Search Results (5,108)

Total knee replacement (TKR) is a common procedure for pain relief and restoration of the mobility of the knee joint in patients with severe knee joint problems. Despite this, some patients still suffer from stiffness, instability, or pain caused by soft tissue imbalance, malalignment, or implant-related issues. Previously, surgeons have had to use their experience and visual judgment to balance the knee, which has resulted in variability of outcomes. Smart knee implants are addressing these issues by using sensor technology to provide real-time feedback on joint motion, pressure distribution, and loading forces. This enables more accurate intra-operative adjustment, enhancing implant positioning and soft tissue balance and eliminating post-operative adjustment. These implants also enable post-operative monitoring, simplifying the ability to have more effective individualized rehabilitation programs directed at optimizing patient mobility and minimizing complications. While the patient pool for smart knee implantation remains not commonly documented, it was found in a study that 83.6% of the patients would opt to have the monitoring device implemented, and nearly 90% find reassurance in monitoring their healing indicators. As the number of knee replacements is likely to rise due to aging populations and the rising prevalence of joint disease, smart implants are a welcome development in orthopedics, optimizing long-term success and patient satisfaction. Smart knee implants are built with embedded sensors such as force, motion, temperature, and pressure detectors placed within the implant structure. These sensors provide real-time data during surgery and recovery, allowing earlier detection of complications and supporting tailored rehabilitation. The design aims to improve outcomes through better monitoring and personalized care. Full article

Background and Objectives: Surgical smoke generated by energy devices during surgery contains hazardous substances and poses health risks to staff in the operating room. Exposure to surgical smoke must be reduced to minimize the risk of health hazards. Many studies have evaluated surgical smoke qualitatively, but few have performed quantitative assessment. The aim of this study was to quantify the number of particles generated during various breast surgery procedures. Materials and Methods: In this prospective, randomized study, breast surgeries performed at Tokyo Medical and Dental University Hospital (the present Institute of Science Tokyo Hospital) between December 2022 and August 2023 were randomly assigned to two groups: the electrosurgical device group and the electrosurgical device with smoke evacuator group. The number of particles generated by energy devices during surgery was measured using a particle counter. Results: Surgical smoke was generated in all procedures. The number of measured particles was significantly less in the electrosurgical device with smoke evacuator group than in the electrosurgical device group during all procedures (all p < 0.001). Conclusions: All breast surgery procedures produced a significant amount of surgical smoke, which was effectively reduced by using an electrosurgical device with a smoke evacuator. These findings support the routine use of smoke evacuators in breast surgery to reduce occupational exposure to hazardous particles. Implementation of such devices could improve operating room safety and may inform future guidelines and institutional policies regarding surgical smoke management. Full article

Sleep is a vital physiological process for recovery and health. In people with knee osteoarthritis (OA), disrupted sleep is common and linked to worse clinical outcomes. Commercial sleep trackers provide an accessible option to monitor sleep in this population, but their accuracy for detecting sleep, wake, and sleep stages remains uncertain. This study compared nighttime sleep data from polysomnography (PSG) and Fitbit Sense in individuals with knee OA and insomnia. Data were collected from 53 participants (60.4% women, mean age 51 ± 8.2 years) over 62 nights using simultaneous PSG and Fitbit recording. Fitbit Sense showed high accuracy (85.76%) and sensitivity (95.95%) for detecting sleep but lower specificity (50.96%), indicating difficulty separating quiet wakefulness from sleep. Agreement with PSG was higher on nights with longer total sleep time, higher sleep efficiency, shorter sleep onset, and fewer awakenings, suggesting better performance when sleep is less fragmented. The device showed limited precision in classifying sleep stages, often misclassifying deep and REM sleep as light sleep. Despite these issues, Fitbit Sense may serve as a useful complementary tool for monitoring sleep duration, timing, and regularity in this population. However, sleep stage and fragmentation data should be interpreted cautiously in both clinical and research settings. Full article

Smartphones have revolutionized our daily lives, becoming portable pocket computers with easy internet access. India, the second-highest smartphone and internet user, experienced a significant rise in smartphone usage between 2013 and 2024. Prolonged smartphone use, exceeding 20 min at a time, can lead to physical and mental health issues, including psychophysiological disorders. Digital devices and their extended exposure to blue light cause digital eyestrain, sleep disorders and visual-related problems. This research examines the impact of 1 h smartphone usage on visual fatigue among young Indian adults. A portable, low-cost system has been developed to measure visual activity to address this. The developed visual activity measurement system measures blink rate, inter-blink interval, and pupil diameter. Measured eye activity was recorded during 1 h smartphone usage of e-book reading, video watching, and social-media reels (short videos). Social media reels show increased screen variations, affecting pupil dilation and reducing blink rate due to continuous screen brightness and intensity changes. This reduction in blink rate and increase in inter-blink interval or pupil dilation could lead to visual fatigue. Full article

In many developing African countries, milk safety is often managed through traditional methods such as fermentation or boiling over firewood. While these approaches reduce some microbial risks, they present critical limitations. Firewood dependency contributes to deforestation, depletion of agricultural residues, and loss of soil fertility, which, in turn, compromise environmental health and food security. Solar pasteurization provides a reliable and sustainable method for thermally inactivating pathogenic microorganisms in milk and other perishable foods at sub-boiling temperatures, preserving its nutritional quality. This study aimed to evaluate the thermal and microbial performance of a low-cost solar milk pasteurization system, hypothesized to effectively reduce microbial contaminants and retain milk quality under natural sunlight. The system was constructed using locally available materials and tailored to the climatic conditions of the Savanna ecological zone in West Africa. A flat-plate glass solar collector was integrated with a 0.15 cm thick stainless steel cylindrical milk vat, featuring a 2.2 cm hot water jacket and 0.5 cm thick aluminum foil insulation. The system was tested in Navrongo, Ghana, under ambient temperatures ranging from 30 °C to 43 °C. The pasteurizer successfully processed up to 8 L of milk per batch, achieving a maximum milk temperature of 74 °C by 14:00 GMT. Microbial analysis revealed a significant reduction in bacterial load, from 6.6 × 10⁶ CFU/mL to 1.0 × 10² CFU/mL, with complete elimination of coliforms. These results confirmed the device’s effectiveness in achieving safe pasteurization levels. The findings demonstrate that this locally built solar pasteurization system is a viable and cost-effective solution for improving milk safety in arid, electricity-limited regions. Its potential scalability also opens avenues for rural entrepreneurship in solar-powered food and water treatment technologies. Full article

Introduction and Objectives: Risk-sharing agreements (RSAs) have emerged as a key strategy for financing high-cost medical technologies while ensuring financial sustainability. These payment mechanisms mitigate clinical and financial uncertainties, optimizing pricing and reimbursement decisions. Despite their widespread adoption globally, Latin America has reported limited implementation, particularly for high-cost medical devices. This study aims to share insights from designing RSAs in the form of Outcome Protection Programs (OPPs) for medical devices in Latin America from the perspective of a medical devices company. Methods: The report follows a structured approach, defining key OPP dimensions: payment base, access criteria, pricing schemes, risk assessment, and performance incentives. Risks were categorized as financial, clinical, and operational. The framework applied principles from prior models, emphasizing negotiation, program design, implementation, and evaluation. A multidisciplinary task force analyzed patient needs, provider motivations, and payer constraints to ensure alignment with health system priorities. Results: Over two semesters, a panel of seven experts from the manufacturer designed n = 105 innovative payment programs implemented in Argentina (n = 7), Brazil (n = 7), Colombia (n = 75), Mexico (n = 9), Panama (n = 4), and Puerto Rico (n = 3). The programs targeted eight high-burden conditions, including Coronary Artery Disease, atrial fibrillation, Heart Failure, and post-implantation arrhythmias, among others. Private providers accounted for 80% of experiences. Challenges include clinical inertia and operational complexities, necessitating structured training and monitoring mechanisms. Conclusions: Outcome Protection Programs offer a viable and practical risk-sharing approach to financing high-cost medical devices in Latin America. Their implementation requires careful stakeholder alignment, clear eligibility criteria and endpoints, and robust monitoring frameworks. These findings contribute to the ongoing dialogue on sustainable healthcare financing, emphasizing the need for tailored approaches in resource-constrained settings. Full article

This paper presents the design, implementation, and experimental validation of a Condition Monitoring (CM) circuit for SiC-based Power Electronics Converters (PECs). The paper leverages in situ drain–source resistance (R_ds,on) measurements, interfaced with cloud connectivity for data processing and lifetime assessment, addressing key limitations in current state-of-the-art (SOTA) methods. Traditional approaches rely on expensive data acquisition systems under controlled laboratory conditions, making them unsuitable for real-world applications due to component variability, time delay, and noise sensitivity. Furthermore, these methods lack cloud interfacing for real-time data analysis and fail to provide comprehensive reliability metrics such as Remaining Useful Life (RUL). Additionally, the proposed CM method benefits from noise mitigation during switching transitions by utilizing delay circuits to ensure stable and accurate data capture. Moreover, collected data are transmitted to the cloud for long-term health assessment and damage evaluation. In this paper, experimental validation follows a structured design involving signal acquisition, filtering, cloud transmission, and temperature and thermal degradation tracking. Experimental testing has been conducted at different temperatures and operating conditions, considering coolant temperature variations (40 °C to 80 °C), and an output power of 7 kW. Results have demonstrated a clear correlation between temperature rise and R_ds,on variations, validating the ability of the proposed method to predict device degradation. Finally, by leveraging cloud computing, this work provides a practical solution for real-world Wide Band Gap (WBG)-based PEC reliability and lifetime assessment. Full article

Introduction: Despite clinical evidence for efficacy, there has been minimal uptake of transcranial direct current stimulation (tDCS) for musculoskeletal conditions. Thus, our objective was to explore the perceptions and experiences of people living with lower-limb musculoskeletal injury as well as healthy physically active populations and relate this to the usage of tDCS and key aspects of tDCS design that would improve the capacity for implementation. Methods: We conducted a qualitative descriptive study of 16 participants (44% women) using semi-structured focus groups to identify the descriptions and experiences of people living with lower-limb musculoskeletal injury and healthy physically active populations. A thematic template was used to create a coding structure. Codes were then grouped, and key themes were derived from the data. Results: Four primary themes were identified from focus groups. These were (i) the impact of musculoskeletal injuries on health and quality of life, (ii) performance and injury recovery as facilitators to using tDCS, (iii) barriers and facilitators to tCDS application and (iv) design and aesthetic factors for a tDCS device. Discussion: Our qualitative descriptive study identified four themes relevant to the successful implementation of tDCS into rehabilitative and performance practice. To increase the likelihood of successful tDCS implementation, these barriers should be addressed and facilitators promoted. This should include innovative approaches to device application and structure that allow for a stylish, user-friendly design. Full article

The COVID-19 pandemic catalyzed the rapid adoption of remote patient monitoring (RPM) technologies such as telemedicine and wearable devices (WDs), significantly transforming healthcare delivery. Telemedicine made virtual consultations possible, reducing in-person visits and infection risks, particularly for the management of chronic diseases. Wearable devices enabled the real-time continuous monitoring of health that assisted in condition prediction and management, such as for COVID-19. This narrative review addresses these transformations by uniquely synthesizing findings from 13 diverse studies (sourced from PubMed and Google Scholar, 2020–2024) to analyze the parallel evolution of telemedicine and WDs as interconnected RPM components. It highlights the pandemic’s dual impact, as follows: accelerating RPM innovation and adoption while simultaneously unmasking systemic challenges such as inequities in access and a need for robust integration approaches; while telemedicine usage soared during the pandemic, consumption post-pandemic, as indicated by the reviewed studies, suggests continued barriers to adoption among older adults. Likewise, wearable devices demonstrated significant potential in early disease detection and long-term health management, with promising applications extending beyond COVID-19, including long COVID conditions. Addressing the identified challenges is crucial for healthcare providers and systems to fully embrace these technologies and this would improve efficiency and patient outcomes. Full article

Molecular sensor systems, e.g., implantables and wearables, provide extensive health-related monitoring. Glucose sensor systems have historically prevailed in wearable bioanalysis applications due to their continuous and reliable glucose monitoring, a feat not yet accomplished for other biomarkers. However, the advancement of reagentless detection methodologies may facilitate the creation of molecular sensor systems for multiple analytes. Improving the sensitivity and selectivity of molecular sensor systems is also crucial for biomarker detection under intricate physiological circumstances. The term multidomain molecular sensor systems is utilized to refer, in general, to both biological and chemical sensor systems. This review examines methodologies for enhancing signal amplification, improving selectivity, and facilitating reagentless detection in multidomain molecular sensor devices. The review also analyzes the fundamental components of multidomain molecular sensor systems, including substrate materials, bodily fluids, power, and decision-making units. The review article further investigates how extensive data gathered from multidomain molecular sensor systems, in conjunction with current data processing algorithms, facilitate biomarker detection for precision medicine. Full article

Consumer-accessible and user-friendly smart products such as unmanned aerial vehicles (UAVs), or drones, have become widely used, adaptable, and acceptable devices to observe, assess, measure, and explore urban and natural environments. A drone’s relatively low cost and flexibility in the level of expertise required to operate it has enabled users from novice to industry professionals to adapt a malleable technology to various disciplines. This review examines the academic literature and maps how drones are currently being used in 93 rural and regional city councils in New South Wales, Australia. Through a systematic review of the academic literature and scrutiny of current drone use in these councils using publicly available information found on council websites, findings reveal potential uses of drone technology for local governments who want to engage with smart technology devices. We looked at how drones were being used in the management of the council’s environment; health and safety initiatives; infrastructure; planning; social and community programmes; and waste and recycling. These findings suggest that drone technology is increasingly being utilised in rural and regional areas. While the focus is on rural and regional New South Wales, a review of the academic literature and local council websites provides a snapshot of drone use examples that holds global relevance for local councils in urban and remote areas seeking to incorporate drone technology into their daily practice of city, town, or region governance. Full article

Background/Objectives: Excessive sugar intake through sugar-sweetened beverages (SSBs) has raised global concerns due to its association with various health risks. This study evaluates the effectiveness of nudges—in the form of order placement, variety expansion, and a combination of both—in promoting non-SSB purchases at self-service kiosks, a key environment for SSB consumption. Methods: This study was conducted using a real-world kiosk at food and beverage outlets in South Korea from 28 May to 12 July, 2024. A total of 183 consumers aged 19 to 29 participated in this study. A single kiosk device was used with four screen layouts, each reflecting a different nudge strategy. Participants were unaware of these manipulations when making their purchases. After their purchases, participants completed a survey. All data were analyzed using IBM SPSS Statistics for Windows, Version 29.0. Results: Females reported significantly higher positive attitudes, preferences, and perceived necessity regarding nudges compared to males. In particular, both the single (variety) and combination (order and variety) nudges received positive responses from females (p < 0.001). The combination nudge significantly increased non-SSB purchases compared to the control (p < 0.05) and single (order) nudge groups (p < 0.01), which suggests that combination nudge is effective in promoting healthier beverage choices. Females were also more likely to purchase non-SSBs than males (p < 0.05). Conclusions: The findings suggest that the combination nudge strategy effectively promotes healthier beverage choices in real kiosk settings. Notably, females demonstrate significantly higher positive attitudes, preferences, and perceived necessity regarding nudges compared to males, and are also more likely to purchase non-SSBs. These findings offer valuable insights for real-world applications aimed at encouraging healthier consumption behaviors. Full article

Spinal cord injury (SCI) is a major disability that, to this day, does not have a permanent cure. The spinal cord extends caudally through the body structure of the vertebral column and is part of the central nervous system (CNS). The spinal cord enables neural communication and motor coordination, so injuries can disrupt sensation, movement, and autonomic functions. Mechanical and traumatic damage to the spinal cord causes lesions to the nerves, resulting in the disruption of relayed messages to the extremities. Various forms of treatment for the spinal cord include functional electrical stimulation (FES), epidural electrical stimulation (EES), ‘SMART’ devices, exoskeleton and robotic systems, transcranial magnetic stimulation, and neuroprostheses using AI for the brain–computer interface. This research is going to analyse and review these current treatment methods for spinal cord injury and identify the current gaps and limitations in these, such as long-term biocompatibility, wireless adaptability, cost, regulatory barriers, and risk of surgery. Future advancements should work on implementing wireless data logging with AI algorithms to increase SCI device adaptability, as well as maintaining regulatory and health system integration. Full article

With the rapid technological advancements in wearable devices, motion and health management have significantly improved, enabling the measurement of various biometric data with compact equipment. Our research focuses on motion measurement but, in general, full-body motion estimation requires motion capture systems or multiple inertial sensors, making it necessary to directly measure movement itself. In this study, we propose estimating full-body posture using inverse kinematics based on trunk posture and limb-end information collected through wearable devices. To enhance estimation accuracy in this underdetermined problem, we employ Physics-Informed Neural Networks (PINNs), which efficiently learn using physical laws as a loss function, along with a high-precision inverse kinematics model of a digital human. Through this approach, we enable high-accuracy full-body posture estimation even with wearable devices in underdetermined scenarios. Full article

The incorporation of digital health into the medical curricula is becoming more important to better prepare doctors in the future. Digital health comprises a wide range of tools such as electronic health records, health information technology, telemedicine, telehealth, mobile health applications, wearable devices, artificial intelligence, and virtual reality. The present study aimed to explore the medical and biomedical students’ perspectives on the integration of digital health in medical curricula. A cross-sectional study was conducted on the medical and biomedical undergraduate students at the College of Medicine and Health Sciences at Sultan Qaboos University. Data was collected using a self-administered questionnaire. The response rate was 37%. The majority of respondents were in the MD (Doctor of Medicine) program (84.4%), while 29 students (15.6%) were from the BMS (Biomedical Sciences) program. A total of 55.38% agreed that they were familiar with the term ‘e-Health’. Additionally, 143 individuals (76.88%) reported being aware of the definition of e-Health. Specifically, 69 individuals (37.10%) utilize e-Health technologies every other week, 20 individuals (10.75%) reported using them daily, while 44 individuals (23.66%) indicated that they never used such technologies. Despite having several benefits, challenges exist in integrating digital health into the medical curriculum. There is a need to overcome the lack of infrastructure, existing educational materials, and digital health topics. In conclusion, embedding digital health into medical curricula is certainly beneficial for creating a digitally competent healthcare workforce that could help in better data storage, help in diagnosis, aid in patient consultation from a distance, and advise on medications, thereby leading to improved patient care which is a key public health priority. Full article