Search Results (676)

Reliable communication infrastructure is a fundamental component of Intelligent Transport Systems (ITSs), particularly in scenarios involving maritime corridors and emergency traffic management. In locations where optical fiber deployment is geographically constrained, unmanned aerial vehicle (UAV)-assisted free-space optical (FSO) relay links provide a flexible and rapidly deployable alternative. However, atmospheric attenuation, turbulence-induced fading, and wind-induced UAV misalignment can severely degrade link reliability and disrupt real-time transport data streams. This study proposes a payload-efficient multiple-input multiple-output free-space optical (MIMO-FSO) relay architecture based on a multi-output/single-input (MOSI) uplink and a single-output/multi-input (SOMI) downlink. Here, MOSI denotes multiple ground-based transmit apertures directed toward a single UAV receiving aperture, whereas SOMI denotes one UAV transmitting aperture serving multiple ground-based receiving apertures. Unlike conventional symmetric UAV-assisted MIMO-FSO relays that may duplicate diversity hardware on the aerial node, the proposed design shifts the parallel optical branches to the ground stations and keeps only one optical receiver and one optical transmitter on board the UAV. Under the adopted 4 × 4 comparison assumption, this reduces the UAV-side optical branch count from eight to two, corresponding to a 75% branch-count reduction proxy. System performance is evaluated over a 1.54 km relay link. The analytical framework describes Beer–Lambert attenuation, log-normal/gamma–gamma turbulence, and statistical pointing errors; in the OptiSystem implementation, their combined effects are represented by equivalent aggregate losses of 25 dB/km for atmospheric absorption/scattering and 25.5 dB/km for turbulence- and pointing-related degradation. Comparative simulations for SISO, 2 × 2, and 4 × 4 configurations show that the proposed 4 × 4 architecture increases the Q-factor from 8.38 to 18.25 and changes the OptiSystem-reported minimum BER from 2.73 × 10⁻¹⁷ to 9.95 × 10⁻⁷⁵. Because a finite simulation cannot statistically validate error probabilities of this magnitude through raw error counting, values far below 10⁻¹² are interpreted primarily as comparative indicators of receiver decision margin. The findings provide simulation-based evidence that the proposed architecture is a scalable candidate for resilient optical wireless backhaul in smart transport corridors under adverse propagation conditions. Full article

Sensor networks increasingly combine exposed sensing nodes, optical communication, photonic hardware, near-sensor inference, and distributed infrastructure monitoring. This changes the security problem from protecting packets alone to establishing device provenance, measurement integrity, link confidentiality and availability, trustworthy inference, physical situational awareness, lifecycle control, and governance. This structured review with documented scoping searches examines security by light: mechanisms in which optical or photonic phenomena directly realize, constrain, compute, or observe a security-relevant function. The review synthesizes screened evidence across photonic roots of trust, visible-light communication and LiFi security, photonic intelligence, reservoir and chaotic photonics, and distributed photonic sensing infrastructure. Searches across arXiv, IEEE Xplore, ACM Digital Library, and Scopus yielded 228 deduplicated candidate records, of which 187 were retained as core evidence and eight as contextual evidence. To avoid overstating heterogeneous photonic work, retained records were separated into direct security evidence, security-adjacent capability evidence, background/framework evidence, and excluded records. The central result is architectural: light-enabled mechanisms are most defensible when they provide explicit, confidence-rated evidence to conventional security engineering. In this paper, confidence-rated evidence means evidence whose security interpretation is tied to a stated asset, adversary or failure mode, evidence role, validation setting, robustness limits, deployment fit, and reproducibility condition. This avoids treating optical novelty, spatial confinement, analog complexity, or high-dimensional dynamics as assurance by themselves. The paper develops an auditable taxonomy, evidence appraisal rubric, mechanism-family synthesis, integration architecture, maturity analysis, and research agenda for incorporating light-enabled mechanisms into secure sensor-networked systems. Full article

The integration requirements of laser ranging, imaging, and communication functions in space target detection have placed higher demands on system performance. This paper takes a modularly designed integrated laser ranging, imaging, and communication system as an example and proposes a light source integration scheme based on fiber phased array beam splitting–coupling technology, effectively enhancing the system’s integration level and compactness. The system employs a Cassegrain optical system and beam splitting structure to achieve functional integration of laser communication, ranging, and polarization imaging. Ground experiments were conducted to evaluate the functional feasibility of the proposed integrated architecture. The visible light polarization imaging experiments at kilometer-level distances demonstrate that polarization-derived information can improve target–background separability under haze and low-contrast conditions. The UAV-based dynamic ranging experiment verifies that the system can acquire, track, and range a moving cooperative target under the tested field conditions, with the measured results being consistent with the designed meter-level ranging requirement. In addition, a 1 km coherent free-space laser communication experiment achieved 20 Gbps QPSK signal transmission with a bit error rate on the order of 10⁻⁷. These results provide experimental support and design references for integrated optoelectronic terminals used in space target observation, space debris monitoring, and related long-distance sensing and communication applications. Full article

This article proposes and experimentally demonstrates a covert key distribution scheme based on the phase fluctuation of a gain-switched laser diode (GSLD). The gain-switched pulse is used to generate the covert signal through spectral broadening and temporal spreading. The amplified spontaneous emission (ASE) light is used to generate ASE noise in the public channel. Eavesdroppers cannot perceive signals hidden in the public noise. The experimental results show that the correlation coefficient of the key waveforms reaches 0.95, and the scheme’s key generation rate (KGR) reaches 1.88 Gbit/s through a 25 km single-mode fiber (SMF). Moreover, the binary bitstreams have passed the NIST statistical test suite. The covert key distribution scheme proposed in this article provides an efficient way for the method of “one-time-pad” key distribution in high-speed optical communication systems. Full article

We propose a time-delay signature suppressed broadband chaotic (TSBC) carrier generation scheme and theoretically investigate its performance in a dual-polarization bidirectional chaotic communication system based on synchronized vertical-cavity surface-emitting lasers (VCSELs). The TSBC scheme is implemented by combining fiber Bragg grating (FBG) feedback with an external electro-optic (EO) phase modulation loop to introduce synergistic nonlinear perturbations. The results demonstrate that the proposed TSBC scheme effectively suppresses the time-delay signature (TDS) to less than 0.03 while significantly enhancing the chaotic carrier bandwidth to over 23 GHz for each polarization channel. Meanwhile, high-quality chaotic synchronization can be achieved with laser parameter mismatches of approximately 30%. Finally, an aggregated 46 Gbit/s dual-polarization bidirectional chaotic transmission is demonstrated, which confirms the effectiveness and the potential of the TSBC dual-polarization bidirectional scheme for secure optical communication applications. Full article

With the advancement of artificial intelligence (AI) technologies such as large language models and autonomous driving, the data traffic via optical interconnects in data centers has surged significantly. The stability of the optical interconnects relies on intelligent operation and maintenance (O&M). Integrated sensing and communication (ISAC) over fibers enables vibration sensing utilizing existing communication fibers, providing critical support for intelligent O&M in data centers. Compared to sensing in the coherent systems, it is difficult to use phase and state of polarization (SOP) monitoring for vibration detection in intensity-modulation and direct-detection (IM-DD) systems. In this paper, we propose a joint phase-based and SOP-based sensing scheme integrated in IM-DD systems. In the proposed scheme, the received IM-DD communication signals are tapped for sensing with a power ratio of 10%. Then the tapped signals are split for vibration sensing based on SOP and phase, respectively. In the phase-based sensing arm, a circulator, a $3\times 3$ coupler and two Faraday rotating mirrors (FRMs) are used to build an unbalanced Michelson interferometer without phase fading and polarization fading. For the purpose of SOP-based sensing, a polarizer is used to monitor the vibration-induced SOP variations. Experimental results demonstrate that the proposed scheme enables vibration sensing based on both phase and SOP across a frequency range of 200 Hz to 10 kHz. Regarding the communication performance, the integration of the sensing system only induces 0.8 dB received optical power penalty. This vibration-sensing scheme based on both phase and SOP can be integrated into pluggable optical modules, providing an efficient and reliable solution for intelligent optical network O&M. Full article

Hydraulic fracture diagnostics are essential for characterizing fracture geometry, connectivity, and effectiveness in unconventional reservoirs. However, the diversity of available techniques and fragmented understanding of their physical mechanisms hinder multidisciplinary communication and lead to inconsistent field decisions. This review provides a systematic assessment of diagnostic methods, focusing on their physical foundations, applicability, and limitations, and proposes a unified reference framework. Direct diagnostics, including microseismic monitoring, fiber-optic sensing (DTS and DAS), and tiltmeter measurements, are evaluated in terms of data characteristics, interpretation challenges, and field applicability. Indirect methods based on pressure, production, and tracer data—such as DFITs, pressure interference tests, and tracer analysis—are examined for their roles in fracture closure evaluation and interwell connectivity. The review further distinguishes between single-well and multi-well applications, providing a structured classification framework. It highlights that individual methods are constrained by non-uniqueness, modeling assumptions, and non-ideal field conditions, especially in complex fracture networks. Therefore, reliable characterization requires integrating multiple diagnostics with physics-based modeling and uncertainty-aware interpretation. Recent advances in AI and machine learning are also briefly discussed as tools to enhance automated analysis and support real-time, predictive diagnostics. Full article

Fiber dispersion causes pulse broadening and signal distortion. Existing dispersion compensation approaches depend on standardized dispersion parameters at specific wavelengths (e.g., 1550 nm), which often mismatch actual fiber dispersion, leading to residual dispersion. We develop a Sagnac ring interferometry and electro-optic modulation system, combined with machine learning, to accurately characterize the C-band dispersion curve of a G.652D fiber, and inversely design a chirped fiber Bragg grating (CFBG) for tailored compensation. However, when attempting to quantify the residual dispersion numerically, conventional differentiation methods yield physically implausible results. Monte Carlo simulations confirm this fundamental unreliability, yielding a 95% confidence interval of 319,605 ps/(nm·km). To circumvent this limitation, we propose a joint evaluation method based on refractive index flatness and group delay uniformity. Within 1545–1555 nm, both indicators fluctuate by no more than 0.015% relative to their means, confirming that residual dispersion has been effectively suppressed. This approach provides a precise, personalized compensation mechanism applicable to optical fibers with individual dispersion characteristics, offering a controllable path for adaptive dispersion compensation in high-speed communication systems. Full article

The terahertz (THz) frequency band has emerged as a promising frontier for next-generation wireless communication systems targeting ultra-high data rates, ultra-low latency, and spectrum expansion beyond conventional millimeter-wave regimes. Realizing practical THz communication links, however, critically depends on stable, tunable, and integrable signal sources capable of delivering sufficient output power while maintaining spectral purity and energy efficiency. Among the various THz generation approaches, optoelectronic techniques offer unique advantages, including large bandwidth, wide frequency tunability and compatibility with fiber-optic infrastructures. This review provides a technology-focused assessment of key optoelectronic THz source technologies, namely photoconductive antennas, quantum cascade lasers, and unitraveling carrier photodiode (UTC-PD)-based photomixers, with particular emphasis on UTC-PD photomixers due to their strong suitability for continuous-wave THz generation and fiber-compatible architectures. The implications of optoelectronic THz sources for system-level architectures, including THz-over-fiber links, coherent detection schemes, and phased-array integration, are further examined. Finally, critical challenges and emerging research directions toward monolithic photonic–terahertz integration and deployable high-capacity wireless front-ends are discussed. This review aims to provide a structured perspective on the state of optoelectronic THz source technologies and their role in enabling practical next-generation communication systems. Full article

Radio-over-Fiber (RoF) integrated with Free-Space Optical (FSO) communication as a fronthaul is a promising solution for next-generation wireless systems, but severely suffers from the frequency-selective characteristics of hybrid RoF-FSO channels. This paper presents a measurement-driven, deployment-oriented optimization that jointly performs structure-aware pilot placement and sixth-order polynomial regression channel interpolation to enhance spectral efficiency and signal quality in quasi-static indoor FSO environments. Differential channel analysis across three transmission scenarios—Electrical Back-to-Back (B2B), Fiber B2B, and FSO—identifies critical subcarriers with high frequency-selective variation that require dense pilot allocation. A gradient-based algorithm positions 50 pilots with dense spacing (every 3 subcarriers) in critical regions and sparse spacing (every 9 subcarriers) in stable regions, reducing pilot overhead by 26.5% and increasing data capacity by 5.3% (340 → 358 subcarriers) compared to uniform placement of 68 pilots. Sixth-order polynomial regression models the non-linear channel frequency response, overcoming limitations of conventional linear interpolation. Experimental validation on a 4-QAM RoF-OFDM system over 40.6 MHz bandwidth shows that structure-aware pilot placement alone reduces Error Vector Magnitude (EVM) by 15.9%, while polynomial regression alone improves it by 15.7%. Combined optimization of structure-aware pilot placement with polynomial regression interpolation achieves 23.5% EVM reduction and 460× lower BER, equivalent to 3.2 dB SNR gain at BER = ${10}^{-6}$. Comparative analysis of four system configurations confirms consistent performance advantages across SNRs of 12–30 dB. The proposed measure-once, optimize-forever paradigm requires only one-time channel characterization, making it suitable for short-range controlled quasi-static indoor FSO links in 5G/6G fronthaul, optical wireless networks, and inter-building backhaul applications. Full article

Mode coupling in multimode step-index polymer optical fibers (SI POFs) plays a critical role in determining signal integrity and bandwidth performance in optical communication systems. It originates from intrinsic random perturbations that influence power distribution among propagating modes, making accurate prediction of steady-state distributions (SSDs) essential for reliable system design. In this work, we model mode coupling as a stochastic process using the Langevin equation, incorporating simulated Langevin forces to numerically evaluate modal power evolution and steady-state behavior. The proposed approach demonstrates strong agreement with previously reported experimental results, validating its capability to capture energy redistribution mechanisms induced by fiber imperfections. From a telecommunications perspective, the model provides valuable insights into modal dispersion, bandwidth limitations, and signal degradation in SI POF-based links. These results establish a robust and efficient framework for analyzing and optimizing multimode SI POFs, supporting their application in high-speed data transmission and short-reach optical communication networks. Full article

The Garisenda Tower, along with the neighboring Asinelli Tower, is arguably the symbol of the city of Bologna. They are the sole remnants of about one hundred towers that formed the city’s skyline in medieval times. As such, the monitoring of their state of health has been of great interest to the scientific community for more than a century—one example being the studies of Prof. Cavani in the early 1900s. The Garisenda Tower, famous for its impressive lean, is the object of Structural Health Monitoring (SHM) involving a multitude of devices. Some examples are a 30 m long pendulum installed on the inside of the tower to measure the planar displacement of the tower’s top; Fiber-Optical Strings (FOSs) installed in the walls of the basement to measure their vertical deformation; and piezoelectric acoustic emission (AE) sensors, also installed on the walls of the tower’s basement to detect elastic waves generated by micro-cracking. This rich experimental setup allows for the investigation of the tower’s stability and damage assessment. In this work, attention is focused on two analyses: The first is a Principal Component Analysis (PCA) study that investigates the correlation between AE data and other SHM data, such as in situ temperature, pendulum displacement, and AE rate. The second analysis corresponds with numerical finite element (FE) studies that assess damage in the base of the tower. Initially, the Smeared Cracking material model is used to understand which zones of the tower are more damaged. Moreover, a possible critical scenario due to increasing tower tilt is investigated. Finally, a viscoelastic formulation of the materials at the base of the tower is used to account for creep to understand the possible viscous effects at the base of the tower. Full article

Permafrost extent and active layer thickness (ALT) have implications for polar-region infrastructure and communities. Much of the world’s permafrost is rich in ground ice and can become highly unstable during seasonal freeze–thaw cycling. Monitoring these dynamics is critical for quantifying infrastructure risk, informing new construction, and prioritizing essential repairs of existing infrastructure. Fiber optic distributed acoustic sensing (DAS) offers an alternative, providing high-resolution monitoring over large distances. This proof-of-concept study evaluates a surface-deployed DAS cable as a rapid, nondestructive tool for observing seasonal thaw in discontinuous permafrost in Fox, Alaska. During three field campaigns (May 2024, September 2024, and June 2025), a surface laid cable recorded active source sledgehammer strikes. Dispersion curves extracted from the surface wave data were aligned with theoretical curves using a simplified two-layer forward model, representing a seasonally thawed layer overlying hard frozen ground. Based on best fit estimates derived from this model, the active layer thickness was calculated at approximately 0.8 m in May 2024, thickening to 1.9 m in September 2024, and 0.65 m in June 2025. These results demonstrate that surface-deployed DAS can effectively observe changes in permafrost seasonal thaw. This technique could be used prior-to and/or in-addition-to performing more invasive, time-consuming subsurface investigation. Full article

Rare-earth-doped microsphere cavities have attracted significant interest for applications in miniaturized photonic devices due to their unique optical properties. In this work, Yb³⁺/Er³⁺ co-doped microsphere cavities were fabricated via a melting method, which enables uniform interior doping at high and tunable rare-earth concentrations through a simpler and more cost-effective process compared with existing coating and fiber-etching approaches. Whispering gallery modes (WGMs) enhanced upconversion luminescence, which was observed using tapered fiber coupling, producing a vivid green fluorescence ring near the equatorial region of the microsphere. The luminescence characteristics of the microsphere cavity were investigated by measuring the fluorescence spectra under varying excitation powers. The results indicated that the fluorescence emission follows a two-photon absorption process, consistent with the upconversion emission mechanism of Er³⁺. A finite difference time domain (FDTD) model was employed to simulate the optical field distribution within the microsphere cavity. At a microsphere diameter of 90 μm and a coupling gap of 0 μm, both the 980 nm pump light and the emitted light were effectively confined near the equatorial region of the microsphere, forming WGM confinement patterns. These findings are expected to advance the application of rare-earth-doped microsphere cavities in fields such as biosensing, bioimaging, optical communications, and upconversion microlasers. Full article

Ultrafast physical random bit generators (PRBGs) are essential components for modern applications in secure communication, quantum cryptography, encrypted optical fiber sensing and artificial intelligence. While optical chaos-based PRBGs offer high-speed capabilities, conventional systems often rely on discrete components that suffer from system complexity and environmental instability. This paper proposes and experimentally demonstrates a robust, integrated solution using a two-section mutual injection DFB laser. The device was fabricated using the reconstruction equivalent chirp (REC) technique, which provides precise control over grating phase variation while utilizing low-cost, high-volume fabrication methods. The laser sections, each measuring 450 μm in length, were designed with a free-running wavelength difference of 0.3 nm to ensure a flat optical spectrum and enhanced chaotic dynamics. By optimizing the bias currents, we achieved a chaos RF bandwidth of 20.1 GHz. Notably, the resulting chaotic signal lacks time-delayed signatures, which simplifies the randomness extraction process. To generate random bits, the chaotic waveform was sampled by an 8-bit analog-to-digital converter at 100 GSa/s. Following post-processing through delay-subtracting and the extraction of the four least significant bits (4-LSBs), we realized a total physical random bit rate of 400 Gb/s. The randomness of the generated sequence was successfully verified using the NIST SP 800-22 statistical test suite. This approach offers a compact, energy-efficient, and high-performance integrated chaotic source suitable for secure communication and high-performance computation. Full article