Search Results (426)

In this study, a novel direct laser beam turning (DLBT) approach is proposed for the precision machining of AISI 308L austenitic stainless steel, which eliminates the need for cutting tools and thereby eradicates tool wear and vibration-induced surface irregularities. A nanosecond-pulsed Nd:YAG fiber laser (λ = 1064 nm, spot size = 0.05 mm) was used, and Ø1.6 mm × 20 mm cylindrical rods were processed under ambient conditions without auxiliary cooling. The experimental framework systematically evaluated the influence of scanning speed, pulse frequency, and the number of laser passes on dimensional accuracy and material removal efficiency. The results indicate that a maximum diameter reduction of 0.271 mm was achieved at a scanning speed of 3200 mm/s and 50 kHz, whereas 0.195 mm was attained at 6400 mm/s and 200 kHz. A robust second-order polynomial correlation (R² = 0.99) was established between diameter reduction and the number of passes, revealing the high predictability of the process. Crucially, when the scanning speed was doubled, the effective fluence was halved, considerably influencing the ablation characteristics. Despite the low fluence, evidence of material evaporation at elevated frequencies due to the incubation effect underscores the complex photothermal dynamics governing the process. This work constitutes the first comprehensive quantification of pass-dependent diameter modulation in DLBT and introduces a transformative, noncontact micromachining strategy for hard-to-machine alloys. The demonstrated precision, repeatability, and thermal control position DLBT as a promising candidate for next-generation manufacturing of high-performance miniaturized components. Full article

This study presents a detailed analysis of the influence of hole presence and size on the behavior of CFRP composite plates subjected to axial compression. The plates were manufactured by an autoclave method from eight-ply laminate in a symmetrical fiber arrangement [45°/−45°/90°/0°₂/90°/−45°/45°]. Four central hole plates of 0 mm (reference), 2 mm, 4 mm, and 8 mm in diameter were analyzed. Tests were conducted using a Cometech universal testing machine in combination with the ARAMIS digital image correlation (DIC) system, enabling the non-contact measurement of real-time displacements and local deformations in the region of interest. The novel feature of this work was its dual use of independent measurement methods—machine-based and DIC-based—allowing for the assessment of boundary condition effects and grip slippage on failure load accuracy. The experiments were carried out until complete structural failure, enabling a post-critical analysis of material behavior and failure modes for different geometric configurations. The study investigated load–deflection and load–shortening curves, failure mechanisms, and ultimate loads. The results showed that the presence of a hole leads to localized deformation, a change in the failure mode, and a nonlinear reduction in load-carrying capacity—by approximately 30% for the largest hole. These findings provide complementary data for the design of thin-walled composite components with technological openings and serve as a robust reference for numerical model validation. Full article

Based on the experience gained worldwide from potential solutions to the fouling problem of fisheries and aquaculture infrastructure, we attempted to design, construct and test the antifouling efficiency of a new hybrid filament created from non-laminated copper wire braided with synthetic fibers made of Dyneema. The design involved the creation of a hybrid twine substituting a percentage of the synthetic fibers with 0.1–0.15 mm diameter copper wire at 5%, 10%, 20% and 40% levels. There is limited information in the international literature for comparison with our results, since there has never been any attempt to create such a hybrid net. The results showed that for the 6 mm mesh, the maximum openness obtained after the 8-month experimental period was 8.72%, with Cu wire substitution at 35%. For the 12 mm mesh, these values were 27.07% at 26%, and for the 20 mm mesh, they were 33.68% at 28%. A conservative average independent from mesh size to achieve optimum openness in the long term is 30 ± 4.73% Cu wire substitution. In addition, we found that both the mesh size (mm) and the copper substitution percentage affected the fouling process during the experimental period, which lasted 8 months. Full article

A ceramic–metal composite was synthesized using sol–gel and electrospinning methods to serve as a SERS substrate. The precursors used were tetraethyl orthosilicate, aluminum nitrate, and zirconium, and polyvinylpyrrolidone was added to electrospun nonwoven fibrous membranes. The membranes were sintered, decorated with silver nanoparticles. The enhancement substrates were made of fibers of cylindric morphology with an average diameter of approximately 190 nm, a smooth surface, and 9 nm spherical particles decorating the surface of the fibers. The enhancement capacity of the substrates was tested using pyridine, methyl orange, methylene blue, crystal violet, and Eriochrome black T at different concentrations with Raman spectroscopy to determine whether the size and complexity of the analyte has an impact on the enhancement capacity. Enhancement factors of 2.53 × 10², 3.06 × 10¹, 2.97 × 10³, 4.66 × 10³, and 1.45 × 10³ times were obtained for the signal of pyridine, methyl orange, methylene blue, crystal violet, and Eriochrome black T at concentrations of 1 nM. Full article

Evaluating the properties of single carbon fibers is crucial, as it provides parameters not only for optimizing carbon fiber production processes but also for enhancing composite material properties. In recent years, significant advancement have been made in the evaluations of the transverse compressive properties of single fibers. However, compressive testing methods for fibers in the fine size range remain limited at the commercial scale. The direct measurement of the transverse compressive properties of three domestic high-strength polyacrylonitrile-based single carbon fibers (T300 grade, T700 grade, and T800 grade) with diameters of ~5.5~6.5 μm was made possible through the use of a micro-compression tester. Transverse compressive moduli of 5.19 GPa (0.050), 5.42 GPa (0.104), and 6.63 GPa (0.120) were obtained for domestic T300-, T700- and T800-grade carbon fibers, respectively. In addition, transverse compressive strengths of 2.35 GPa (0.033), 2.65 GPa (0.041), and 2.82 GPa (0.121) were obtained for domestic T300-, T700- and T800-grade carbon fibers, respectively. It is noted that minor deviations in fiber geometry from an ideal circular cross-section may influence absolute modulus and strength values. These fibers exhibit strong anisotropy in the longitudinal and transverse directions from the fiber axis. A correlation between the transverse compressive modulus and strength was found for these fibers. These results provide critical parameters for the optimization of carbon fiber-reinforced composite designs (e.g., enhancing impact resistance in aerospace structures), offering substantial practical value to the field of materials science. Full article

This study proposes a novel algorithm for generating representative volume elements which mitigate microstructural inhomogeneities in fiber-reinforced composites. The algorithm integrates void characteristics obtained from micro-computed tomography to more accurate microstructure models. Based on these models, the effects of void content, spatial distribution, and void diameter on the mechanical behavior of CF/PEEK composites are systematically evaluated using finite element analysis and experimental validation. The results reveal that void content significantly reduces transverse tensile strength and ductility, while void size further accelerates failure and enhances brittleness. In contrast, void distribution has minimal influence on the transverse mechanical response. These findings not only offer qualitative insights into void-induced damage mechanisms but also provide a theoretical basis for optimizing microstructures to enhance the mechanical performance of CF/PEEK and similar composite systems. Finally, the limitations of this study have been discussed, and directions for future research are proposed. Full article

In this work, the effect of the palladium precursor on the Oxygen Reduction Reaction (ORR) performance of lignin-based electrospun carbon fibers was studied. The fibers were spun from a lignin-ethanol solution free of any binder, where different Pd salts were added at two concentration levels. The system implemented to perform the spinning was a coaxial setup in which the internal flow contains the precursor dispersion with the metallic precursor, and ethanol was used as external flow to help fiber formation and prevent drying before generating the Taylor cone. The obtained cloths were thermostabilized in air at 200 °C and carbonized in nitrogen at 900 °C. The resulting carbon fibers were characterized by physicochemical and electrochemical techniques. The palladium precursor significantly affects nanoparticle distribution and size, fiber diameter, pore distribution, surface area and electrochemical behavior. The fibers prepared with palladium acetylacetonate at high Pd loading and carbonized at 900 °C under a CO₂ atmosphere showed high mechanical stability and the best ORR activity, showing near total selectivity towards the 4-electron path. These features are comparable to those of the commercial Pt/C catalyst but much lower metal loading (10.6 wt.% vs. 20 wt.%). The most promising fibers have been evaluated as cathodes in a zinc–air battery, delivering astonishing stability results that surpassed the performance of commercial Pt/C materials in both charging and discharging processes. Full article

Government regulations have required consumer products—electrical and electronic components, toys, furniture, clothing, and cars— to meet ever-increasing flame resistance standards, and industry has met these norms by adding brominated fire retardants. However, end-of-life treatment and up-cycling of these plastics is challenging as the brominated compounds are endocrine disruptors, bioaccumulators, and persist in the environment. Pyrolysis, catalytic cracking, or combustion, to recover its fuel value, produces toxic brominated dibenzodioxins and dibenzofurans Here, we demonstrated the efficacy of a solvothermal treatment that extracts up to 99% of the bromine from high-impact polystyrene (HIPS) and polystyrene (PS) in electrical and electronic waste (e-waste). The process operated between 160 °C and 230 °C with ethylene glycol or triethylene glycol as the solvent and NaOH or KOH as the extraction agent (0.5 M to 2 M). The reaction rates depended on the particle size: 60 mm plastic chunks took up to between 4 and 24 h to react while fibers 3 mm in diameter reacted in less than 5 min. Full article

This study evaluated the effect of mixed meal replacement of soybean meal on growth conditions, carcass traits, and meat quality of finishing pigs by partially and entirely replacing soybean meal with equal proportions of rapeseed, cotton, and sunflower meal. A total of fifty-four pigs with an average initial weight of 97.60 ± 0.30 kg were selected and randomly divided into three groups according to their initial weight, with six pens in each group and three pigs in each pen. The experimental groups were as follows: control group (CON), fed corn–soybean meal type basal diet; corn–soybean mixed meal group (CSM), using equal proportions of rapeseed meal, cotton meal, and sunflower meal (3.52% each) to replace 9.06% of soybean meal in the basal diet; and corn mixed meal group (CMM), using equal proportions of rapeseed meal, cotton meal, and sunflower meal (6.46% each) to replace soybean meal in the basal diet completely. According to the results, the use of mixed meal as a replacement for soybean meal did not have a significant impact (p > 0.05) on the average daily weight gain, average daily feed intake, feed-to-weight ratio, body size, carcass traits, and meat quality of finishing pigs. The entire replacement of soybean meal with a mixed meal resulted in a significant increase (p < 0.05) in leaf fat weight. The use of mixed meal as a substitute for soybean meal had no significant effect (p > 0.05) on the antioxidant capacity and fatty acid composition of the longissimus thoracis in finishing pigs. However, longissimus thoracis muscle fiber diameter was reduced in the mixed meal partially replaced soybean meal group compared to the mixed meal completely replaced soybean meal group (p < 0.05). In addition, mixed meal replacing soybean meal did not significantly affect (p > 0.05) the expression of the longissimus thoracis muscle fiber type genes MYHC1 and MYHC2. Mixed meal replacement of soybean meal did not significantly affect (p > 0.05) the expression of ACACA, FASN, and PPARG genes in the longissimus thoracis. This study showed that mixed meal as an alternative to soybean meal in diets did not have significant negative effects on the growth performance and meat quality of finishing pigs. These results can help develop further mixed meals as a functional alternative feed ingredient for soybean meals in pig diets. Full article

Vitamin E is widely used in cosmetics and dermatological applications for its antioxidant, anti-inflammatory, and healing properties, yet its industrial use is limited by poor stability and bioavailability. To address these challenges, this study developed zein-based microstructures encapsulating vitamin E using electrohydrodynamic (EHD) techniques and evaluated how zein concentration affects morphology and release behavior. The SEM analysis showed that biopolymer (zein) concentration significantly affects microstructure morphology. At low concentrations (1%, 5%, and 15% (w/v)), micro/nanoparticles are formed, and high concentrations (30% (w/v)) yielded only fibers. The average size of the structures produced with zein (1–15% w/v) ranged from 0.38 to 0.90 µm, as measured using the program ImageJ (v1.54d). Structures containing vitamin E were generally smaller than those without. For electrospun fibers made with 30% zein, diameters ranged from 0.49 to 0.74 µm, with vitamin E-containing fibers also being thinner. Conductivity also influenced morphology; higher conductivity developed fibers, while lower conductivity formed particles. The solution with 15% (w/v) zein + 1% (w/w) vitamin E showed a conductivity of 1276 μS, similar to the 15% zein solution (1280 μS), indicating that vitamin E addition had no significant effect on conductivity. Release assays revealed that structures produced with low zein concentrations led to immediate release, while structured made with higher concentrations, prolonged release. A preliminary cosmetic formulation test has been conducted. The vitamin E microstructures were successfully incorporated into aloe vera hydrogel and coconut oil to show their potential for cosmetic applications. Full article

This study investigates the mechanical and impact resistance properties of high-performance cementitious composites (HPCCs) incorporating hybrid fibers under a low water-to-binder ratio, with a focus on the multi-scale synergistic effects of different fiber types. Aramid fibers (AFs), basalt fibers (BFs), and calcium sulfate whiskers (CSWs) contribute to reinforcement at the macro, meso, and micro levels, respectively. Experimental results reveal that hybrid fiber systems significantly outperform single-fiber composites in terms of both impact resistance and crack suppression. The optimal mix design—comprising 3% CSW, 0.067% AF, and 0.033% BF—achieved a remarkable 233.3% increase in impact energy absorption compared to the control group. This enhancement is attributed to the complementary roles of the three fibers: CSWs refine the pore structure and mitigate microcrack propagation; AFs effectively restrain the development of macrocracks due to their high tensile strength and aspect ratio; and BFs contribute to energy dissipation through crack bridging and mechanical interlocking. Statistical analysis using the two-parameter Weibull distribution accurately characterized the variability and reliability of the impact resistance data, while pore structure analysis confirmed a reduction in average pore diameter and a more favorable pore size distribution. These findings underscore the effectiveness of fiber hybridization in improving the mechanical behavior and dynamic load resistance of cement-based composites, offering valuable insights for their application in demanding engineering scenarios. Full article

The agri-food supply chain and other industries that convert agricultural raw materials into various consumer goods generate large quantities of by-products, most of which end up in landfills. This waste, rich in cellulose, provides a significant opportunity for the conversion of agricultural residues into valuable products. In this paper, soybean hulls and hemp waste were subjected to chemical treatments with alkaline (NaOH 2% w/v) and acidic solutions (HCl 1 M) to remove non-cellulosic components and isolate cellulose. The biomass was characterized after each chemical process through FTIR, SEM, EDX, elemental analysis, TGA, and XRD. Lignin was determined following two different procedures, a conventional TAPPI protocol and a method recently proposed in the literature (CASA method). The results indicated that the chemical treatments favored the removal of organic compounds and minerals, increasing the cellulose content in biomass after each step. The purified product of soybean hulls consists of fibers 35–50 µm long and 5–11 µm thick, containing nearly pure cellulose arranged in crystalline domains. Fibers of variable sizes, rich in crystalline cellulose, were isolated from hemp waste. These fibers have diameters ranging between 2 and 60 µm and lengths from 40 to 800 µm and contain considerable amounts of lignin (~14%). Full article

In this work, we report the synthesis of perovskite-type Ba-doped LaFeO₃ (La_1−xBa_xFeO₃, x = 0.00, 0.02, 0.04, and 0.06) nanofibers (NFs) using the electrospinning method. The synthesized La_1−xBa_xFeO₃ materials have a fibrous structure with an average fiber diameter of 250 nm. The fibers, in turn, consist of smaller crystalline particles of 20–50 nm in size. The sensor properties of La_1−xBa_xFeO₃ nanofibers were studied when detecting 20 ppm CO, CH₄, methanol, and acetone in dry air in the temperature range of 50–350 °C. Doping with barium leads to a significant increase in sensor response and a decrease in operating temperature when detecting volatile organic compounds (VOCs). The process of acetone oxidation on the surface of the most sensitive La_0.98Ba_0.02FeO₃ material was studied using in situ diffuse reflectance infrared Fourier transform spectroscopy (DRIFTS) and temperature-programmed desorption in combination with mass spectrometry (TPD-MS). A mechanism for the sensor signal formation is proposed. Full article

This research introduces a biosensor utilizing surface plasmon resonance in a photonic crystal fiber (PCF) configuration. PCF uses fused silica as the base material, with a layer of gold placed over the U-channels in the cross-section of the fiber to create a surface plasmon resonance. There are three different sizes of internal fiber optic air hole diameters, with a larger channel circle below the u-channel for the formation of an energy leakage window. COMSOL software 6.0 assisted us in tuning the fiber optic structure and performance for the study, and the structural parameters analyzed mainly include the channel circle diameter, the channel circle spacing, the profundity measurement of the polished layer, and the nanoscale size variation of metal films. The results of the simulation study show that the optical fiber sensor achieves refractive index (RI) responsiveness across the 1.30 to 1.41 range, and in the RI interval of 1.40 to 1.41, the sensor exhibits the largest resonance peak shift, and its highest sensitivity reaches 10,200 nm/RIU, and the smallest full width at half peak (FWHM) corresponds to the RI of 1.34 with a value of 4.8 nm, and the highest figure of merit (FOM) corresponds to the RI of 1.34 with a value of 895.83 (1/RIU). COMSOL 6.0 simulation software, was used to simulate the changes in blood refractive index corresponding to different glucose concentrations, and the detection performance of the sensor for different concentrations of glucose was tested. Then, the results show that the glucose concentration in 75 mg/dL–175 mg/dL with RI detection sensitivity is 3750 nm/RIU, where the maximum refractive index sensitivity is 5455 nm/RIU. It shows that the sensor can be applied in the field of biomedical applications, with its convenience, fast response, and high sensitivity, it has great potential and development prospect in the market. Full article

Background/Objectives: Low-frequency alternating current (LFAC) has been shown to induce nerve conduction block (LFACb). However, the effects of LFAC on conduction delay prior to block remain unclear. This study investigates the impact of LFACb on conduction velocity and blocking thresholds in myelinated and unmyelinated fibers using experimental and computational models. Methods: Four models were employed to analyze LFACb effects: (1) in-vivo experiments in earthworms examined conduction delays across nerve bundles with distinct conduction velocities; (2) ex-vivo experiments in canine vagus nerves assessed the upstream and downstream effects of LFAC waveforms ranging from 50 mHz to 500 mHz; (3) in-silico simulations using the Horn, Yoshida, and Schild (HYS) model for unmyelinated fibers explored size-dependent conduction delays and blocking thresholds; and (4) in-silico simulations using the McIntyre, Richardson, and Grill (MRG) model extended to 504 Nodes of Ranvier characterized myelination effects, localized nodal interactions, and diameter-dependent thresholds. Results: LFAC-induced conduction delays were independent of LFAC frequency but strongly influenced by fiber diameter and conduction velocity. Larger fibers exhibited lower block thresholds and shorter delays before block onset. In contrast, smaller fibers demonstrated prolonged subthreshold conduction delays before achieving full block. Conclusions: These findings suggest that LFACb could serve as a neuromodulation tool for selectively blocking larger fibers while preserving smaller fiber function. This has potential applications in functional electrical stimulation (FES) and temporary, non-destructive nerve blocks for clinical and research applications. Full article