Search Results (215)

In this article, femtosecond laser scanning was used to create heterojunctions between silver nanowire (Ag NW) and graphene oxide (GO), resulting in a mechanical and electrical interconnection. Surface plasmon resonances (SPRs) were generated on the nanowire surface by using femtosecond laser irradiation, producing a periodically excited electric field along the Ag NWs. This electric field then interfered with the femtosecond laser field, creating strong localized heating effects, which melted the Ag NW and GO, leading to mechanical bonding between the two. The formation of these heterostructures was attributed to the transfer of plasmon energy from the Ag NW to the adjacent GO surface. Since the connection efficiency of the nanowires is closely related to the specific location and the polarization direction of the laser, FDTD simulations were conducted to model the electric field distribution on the surface of Ag NW and GO structures under different laser polarization directions, varying the lengths and diameters of the nanowires. Finally, the resistance changes of the printed Ag NW paths on the GO thin film after femtosecond laser irradiation were investigated. It was found that laser bonding could reduce the resistance of the Ag NW-GO heterostructures by two orders of magnitude, further confirming the formation of the junctions. Full article

This paper focuses on the switching and modulation techniques of terahertz waves, develops ${\mathrm{VO}}_2$ thin-film materials with an SPP structure, and uses terahertz time-domain spectroscopy (THz-TDS) to study the semiconductor–metal phase transition characteristics of ${\mathrm{VO}}_2$ thin films, especially the photoinduced semiconductor–metal phase transition characteristics of silicon-based ${\mathrm{VO}}_2$ thin films. The optical modulation characteristics of silicon-based ${\mathrm{VO}}_2$ thin films to terahertz waves under different light excitation modes, such as continuous light irradiation at different wavelengths and femtosecond pulsed laser irradiation, were analyzed. Combining the optical modulation characteristics of silicon-based ${\mathrm{VO}}_2$ thin films with the filtering characteristics of SPP structures, composite structures of ${\mathrm{VO}}_2$ thin films with metal hole arrays, composite structures of ${\mathrm{VO}}_2$ thin films with metal block arrays, and silicon-based ${\mathrm{VO}}_2$ microstructure arrays were designed. The characteristics of this dual-function device were tested experimentally. The experiment proves that the ${\mathrm{VO}}_2$ film material with an SPP structure has a transmission rate dropping sharply from 32% to 1% under light excitation; the resistivity changes by more than six orders of magnitude, and the modulation effect is remarkable. By applying the SPP structure to the ${\mathrm{VO}}_2$ material, the material can simultaneously possess modulation and filtering functions, enhancing its optical performance in the terahertz band. Full article

This study investigates near-infrared (NIR)-induced, Phyto-enhanced, second harmonic generation-mediated photodynamic therapy (Phyto-SHG-PDT) using barium titanate (BT)/rhein/polyethylene glycol 100 (PEG100) and BT/Yemenite “Etrog” leaf extract/PEG100 nanoconjugates. We compare continuous-wave (CW), multi-line Argon-ion laser illumination in the NIR range with high-peak-power femtosecond (fs) 800 nm pulses. Under CW NIR light, BT/rhein nanoconjugates reduced PC3 prostate cancer cell viability by 18% versus non-irradiated controls (p < 0.05), while BT/extract nanoconjugates exhibited 15% dark toxicity. The observed SHG signal matched theoretical predictions and previous CW laser studies. Reactive Oxygen Species (ROS) scavenger 1,3-diphenyl-isobenzofuran (DPBF) showed reduced absorbance at 410 nm upon NIR illumination, indirectly supporting SHG emission at 400 nm from nanoconjugates. Under fs-pulsed laser exposure, pronounced two-photon absorption (TPA) and SHG effects were observed in both nanoconjugate types. Our results demonstrate the effectiveness of BT/rhein nanoconjugates under both laser conditions, while the BT/extract nanoconjugates benefited from high-power pulsed excitation. These results highlight the potential of BT-based Phyto-SHG-PDT nanoconjugates for NIR and blue light applications, leveraging nonlinear optical effects for advanced photochemical cancer therapies. Full article

Boron nitride nanotubes (BNNTs) are predicted to be promising one-dimensional nonlinear optical materials, but to date, only one experimental observation has been made using individual nanotubes. In this work, second harmonic generation (SHG) was achieved from free-standing bulk BNNT sheets and BNNT coatings on silica substrates. Focusing femtosecond infrared (fs-IR) laser pulses with a wavelength of 800 nm onto the BNNT assemblies resulted in strong SHG at a wavelength of 400 nm. It was observed that due to the thickness variation of the BNNT assemblies and orientational alignment of BNNTs in the assemblies, the intensity of the second-harmonic (SH) radiation changed dramatically when different locations on the samples were investigated. Among all the BNNT assemblies tested, the localized SH response and its dependence on the polarization of the excitation fs-IR pulses were the strongest in BNNT coatings produced by a dip-coating process. By measuring the SH response, the uniformity, reproducibility, and efficiency of BNNT deposition processes could be assessed. For applications requiring a high SH response from BNNT assemblies, the process of dip coating is preferred. Full article

In this paper, we report on the growth and characterization of high doping concentration (2.1 at%) ytterbium (Yb) doped lithium niobate (Yb:LiNbO₃) crystal. By using a slightly modified Czochralski method, we have successfully grown a usable size (2 mm × 2 mm × 30 mm) Yb:LiNbO₃ single crystal. We also conducted the energy-dispersive X-ray spectroscopy (EDS) and the X-ray diffraction (XRD) analyses, which experimentally confirm that the grown crystal is a Yb:LiNbO₃ single crystal. We also measured the absorption and emission spectra of the grown crystal. It was found out that there is a near-flat broad emission within a spectral range of 1004–1030 nm when excited at 980 nm for this high doping concentration Yb:LiNbO₃ crystal. Such a near-flat broad emission can be very useful for realizing high slope efficiency ultrafast (femtosecond) lasing in the Yb:LiNbO₃ crystal due to the low quantum defect of the Yb:LiNbO₃ crystal. We also investigated the electro-optic effect of the Yb:LiNbO₃. The experimental result confirms that the electro-optic (EO) effect of a highly doped (2.1 at%) lithium niobate crystal is close to the EO value of the pure lithium niobate. Thus, the highly doped Yb:LiNbO₃ crystal can still be an effective electrically tunable lasing medium. It can enable electrically tunable, high slope efficiency femtosecond lasing due to the combined features, including (1) a near flat broad emission spectrum at the spectral range of 1004–1030 nm, (2) a non-compromised electro-optic effect at high doping concentration Yb:LiNbO₃ crystal, and (3) a low quantum defect. Full article

In this report, the nonlinear optical (NLO) properties of titanium dioxide nanoparticles (TiO₂ NPs) have been explored experimentally using femtosecond laser light along with the Z-scan approach. The synthesis of TiO₂ NPs was carried out in distilled water through nanosecond second harmonic Nd:YAG laser ablation. Characterization of the TiO₂ NPs colloids was conducted using UV-visible absorption spectroscopy, transmission electron microscopy (TEM), inductively coupled plasma (ICP), and energy-dispersive X-ray spectroscopy (EDX). The TEM analysis indicated that the size distribution and average particle size of the TiO₂ NPs varied from 8.3 nm to 19.1 nm, depending on the laser ablation duration. The third-order NLO properties of the synthesized TiO₂ NPs were examined at different excitation laser wavelengths and incident powers through both open- and closed-aperture Z-scan techniques, utilizing a laser pulse duration of 100 fs and a high repetition rate of 80 MHz. The nonlinear absorption (NLA) coefficient and nonlinear refractive (NLR) index of the TiO₂ NPs colloidal solutions were found to be influenced by the incident power, excitation wavelength, average size, and concentration of TiO₂ NPs. Maximum values of 4.93 × 10⁻⁹ cm/W for the NLA coefficient and 15.39 × 10⁻¹⁵ cm²/W for the NLR index were observed at an excitation wavelength of 800 nm, an incident power of 0.6 W, and an ablation time of 15 min. The optical limiting (OL) effects of the TiO₂ NPs solution at different ablation times were investigated and revealed to be concentration and average size dependent. An increase in concentration results in a more limiting effect. Full article

Biosensors operating in the terahertz (THz) region are gaining substantial interest in biomedical analysis due to their significant potential for high-sensitivity trace-amount solution detection. However, progress in compact, high-sensitivity chips and methods for simple, rapid and trace-level measurements is limited by the spatial resolution of THz waves and their strong absorption in polar solvents. In this work, a compact nonlinear optical crystal (NLOC)-based reflective THz biosensor with a few arrays of asymmetrical meta-atoms was developed. A near-field point THz source was locally generated at a femtosecond-laser-irradiation spot via optical rectification, exciting only the single central meta-atom, thereby inducing Fano resonance. The reflective resonance response demonstrated dependence on several aspects, including structure asymmetricity, geometrical size, excitation point position, thickness and array-period arrangement. DNA samples were examined using 1 μL applied to an effective sensing area of 0.234 mm² (484 μm × 484 μm) for performance evaluation. The developed Fano resonance sensor exhibited nearly double sensitivity compared to that of symmetrical sensors and one-gap split ring resonators. Thus, this study advances liquid-based sensing by enabling easy, rapid and trace-level measurements while also driving the development of compact and highly sensitive THz sensors for biological samples. Full article

This study presents the development of highly efficient Surface-Enhanced Raman Scattering (SERS) substrates through femtosecond (fs) laser processing of crystalline silicon (Si), resulting in mountain-like microstructures. These microstructures, when decorated with gold nanoparticles (Au NPs), exhibit remarkable SERS performance due to the creation of concentrated hotspots. The enhanced Raman signals originate from the excitation of localized surface plasmon resonance (LSPR) of the Au NPs and the multi-scale rough morphology of the Si substrates. Finite-element method simulations confirm the electromagnetic field enhancement in narrow gaps, supporting the experimental observations. The fabricated substrates show high uniformity, oxidation resistance, long-term stability, and exceptional reproducibility, making them ideal for molecular detection, especially in food safety applications. A remarkable enhancement factor (EF) of 10¹⁰ is attained in the detection of Malachite Green (MG), boasting a limit of detection (LoD) as low as 10⁻¹⁴ M. This underscores the immense potential of this technique for achieving highly sensitive and dependable SERS-based sensing capabilities. Full article

A highly sensitive optical fiber gas pressure sensor with temperature monitoring is proposed and demonstrated. It is based on a slightly tapered fiber with an inner micro-cavity forming an in-fiber Mach–Zehnder interferometer (MZI), and a micro-channel is drilled into the lateral wall of the in-fiber micro-cavity using a femtosecond laser to allow gas to flow in. Due to the dependence of the refractive index (RI) of air inside the micro-cavity on its gas pressure and the high RI sensitivity of the MZI, the device is extremely sensitive to gas pressure. To prevent fiber breakage, the MZI is housed in a silicate capillary tube with an air inlet. Multiple modes are excited by slightly tapering the inner micro-cavity, and the resonance dips in the sensor’s transmission spectrum feature different linear gas pressure and temperature responses, so a sensitivity matrix algorithm can be used to achieve simultaneous demodulation of two parameters, thus resolving the temperature crosstalk. As expected, the experimental results demonstrated the reliability of the matrix algorithm, with pressure sensitivity reaching up to ~−12.967 nm/MPa and temperature sensitivity of ~89 pm/°C. The features of robust mechanical strength and high air pressure sensitivity with temperature monitoring imply that the proposed sensor has good practical and application prospects. Full article

Excited-state intramolecular proton transfer (ESIPT) reactions are crucial in photoresponsive materials and fluorescent markers. The fluorescent compound 4-aminophthalimide (4-AP) has been reported to exhibit solvent-assisted ESIPT in protic solvents, such as methanol, wherein the solvent interacts with 4-AP to form a six-membered hydrogen-bonded ring that is strengthened upon excitation. Although the controversial observation of ESIPT in 4-AP has been extensively studied, the molecular mechanism has yet to be fully explored. In this study, femtosecond infrared spectroscopy was used to investigate the dynamics of 4-AP in methanol and acetonitrile after excitation at 350 and 300 nm, which promoted 4-AP to the S₁ and S₂ states, respectively. The excited 4-AP in the S₁ state relaxed to the ground state, while 4-AP in the S₂ state relaxed via the S₁ state without the occurrence of ESIPT. The enol form of 4-AP (Enol 4-AP) in the S₁ state was calculated to be ~10 kcal/mol higher in energy than the keto form in the S₁ state, indicating that keto-to-enol tautomerization was endergonic, ultimately resulting in no observable ESIPT for 4-AP in the S₁ state. Upon the excitation of 4-AP to the S₂ state, the transition to Enol-4-AP in the S₁ state was found to be exergonic; however, ESIPT must compete with an internal conversion from the S₂ to the S₁ state. The internal S₂ → S₁ conversion was significantly faster than the solvent-assisted ESIPT, resulting in a negligible ESIPT for the 4-AP excited to the S₂ state. The detailed excitation dynamics of 4-AP clearly reveal the molecular mechanism underlying its negligible ESIPT, despite the fact that it forms a favorable structure for solvent-assisted ESIPT. Full article

The operation of bacteriorhodopsin (BR) from the archaeon Halobacterium salinarum is based on the photochromic reaction of isomerization of the chromophore group (the retinal protonated Schiff base, RPSB) from the all-trans to the 13-cis form. The ultrafast dynamics of the reverse 13-cis → all-trans photoreaction was studied using femtosecond transient absorption spectroscopy in comparison with the forward photoreaction. The forward photoreaction was initiated by photoexcitation of BR by pulse I (540 nm). The reverse photoreaction was initiated by photoexcitation of the product K₅₉₀ at an early stage of its formation (5 ps) by pulse II (660 nm). The conversion of the excited K₅₉₀ to the ground state proceeds at times of 0.19, 1.1, and 16 ps with the relative contributions of ~20/60/20, respectively. All these decay channels lead to the formation of the initial state of BR as a product with a quantum yield of ~1. This state is preceded by vibrationally excited intermediates, the relaxation of which occurs in the 16 ps time range. Likely, the heterogeneity of the excited state of K₅₉₀ is determined by the heterogeneity of its chromophore center. The forward photoreaction includes two components—0.52 and 3.5 ps, with the relative contributions of 91/9, respectively. The reverse photoreaction initiated from K₅₉₀ proceeds more efficiently in the conical intersection (CI) region but on the whole at a lower rate compared to the forward photoreaction, due to significant heterogeneity of the potential energy surface. Full article

Metallic nanoparticles have gained attention in technological fields, particularly photonics. The creation of silver/gold (Ag/Au) alloy NPs upon laser exposure of an assembly of these NPs was described. First, using the Nd: YAG pulsed laser ablation’s second harmonic at the same average power and exposure time, Ag and Au NPs in distilled water were created individually. Next, the assembly of Ag and Au NP colloids was exposed again to the pulsed laser, and the effects were examined at different average powers and exposure times. Furthermore, Ag/Au alloy nanoparticles were synthesized with by raising the average power and exposure time. The absorption spectrum, average size, and shape of alloy NPs were obtained by using an ultraviolet-visible (UV–Vis) spectrophotometer and transmission electron microscope instrument. Ag/Au alloy NPs have been obtained in the limit of quantum dots (<10 nm). The optical band gap energies of the Ag/Au alloy colloidal solutions were assessed for different Ag/Au alloy NP concentrations and NP sizes as a function of the exposure time and average power. The experimental data showed a trend toward an increasing bandgap with decreasing nanoparticle size. The nonlinear optical characteristics of Ag/Au NPs were evaluated and measured by the Z-scan technique using high repetition rate (80 MHz), femtosecond (100 fs), and near-infrared (NIR) (750–850 nm) laser pulses. In open aperture (OA) Z-scan measurements, Ag, Au, and Ag/AuNPs present reverse saturation absorption (RSA) behavior, indicating a positive nonlinear absorption (NLA) coefficient. In the close-aperture (CA) measurements, the nonlinear refractive (NLR) indices (n₂) of the Ag, Au, and Ag/Au NP samples were ascribed to the self-defocusing effect, indicating an effective negative nonlinearity for the nanoparticles. The NLA and NLR characteristics of the Ag/Au NPs colloids were found to be influenced by the incident power and excitation wavelength. The optical limiting (OL) effects of the Ag/Au alloy solution at various excitation wavelengths were studied. The OL effect of alloy NPs is greater than that of monometallic NPs. The Ag/Au bimetallic nanoparticles were found to be more suitable for optical-limiting applications. Full article

Femtosecond lasers have garnered widespread attention owing to their subdiffraction processing capabilities. However, their intricate natures, involving intrapulse feedbacks between transient material excitation and laser propagation, often present significant challenges for near-field ablation predictions and simulations. To address these challenges, the current study introduces an improved finite-difference time-domain method (FDTD)–plasma model (plasma)–two-temperature model (TTM) framework for simulating the ablation processes of various nanospheres on diverse substrates, particularly in scenarios wherein dynamic and heterogeneous excitations significantly influence optical-field distributions. Initially, FDTD simulations of a single Au nanosphere on a Si substrate reveal that, with transitions in the excitation states of the substrate, the field-intensity distribution transforms from a profile with a single central peak to a bimodal structure, consistent with experimental reports. Subsequently, simulations of a polystyrene nanosphere array on a SiO₂ substrate reveal that different excitation states of the nanospheres yield two distinct modes, namely near-field enhancement and masking. These modes cannot be adequately modeled in the FDTD simulations. Our combined model also considers the intrapulse feedback between the electromagnetic-field distribution resulting from near-field effects and material excitations. Furthermore, the model can quantitatively analyze subsequent electron–phonon coupling and material removal processes resulting from thermal-phase transitions. Consequently, our model facilitates predictions of the femtosecond-laser ablation of single nanospheres or nanosphere arrays with varying sizes and materials placed on substrates subjected to near-field effects. Full article

Laser-induced fluorescence spectroscopy (LIFS) is actively used for remote sensing of atmospheric aerosols and is currently one of the most sensitive and selective techniques for determining small concentrations of substances inside particles. The use of high-power femtosecond laser sources for LIFS-based remote sensing of aerosols contributes to the development of new-generation fluorescence atmospheric lidars since it makes it possible to overcome the energy threshold for the nonlinear-optical effects of multiphoton absorption in particles and receive the emission signal at long distances in the atmosphere. Our study is aimed at the development and experimental demonstration of the technique of nonlinear laser-induced fluorescence spectroscopy (NLIFS) based on the remote excitation of aerosol fluorescent emission stimulated by a spatially structured high-power femtosecond laser pulse. Importantly, for the first time to our knowledge, we demonstrate the advances in using stochastically structured plasma-free intense light channels (postfilaments) specially formed by the propagation of femtosecond laser radiation through a turbulent air layer to improve NLIFS efficiency. A multiple increase in the received signal of two-photon-excited fluorescence of polydisperse-dyed aqueous aerosols by the structured postfilaments is reported. Full article

The thermal stability of oxyfluorotellurite glass systems, (65-x)TeO₂-20ZnF₂-12PbO-3Nb₂O₅-xPr₂O₃, doped with praseodymium was examined. The different concentrations of praseodymium oxide (x = 0.5 and 2 mol%) were applied to verify the thermal, optical and luminescence properties of the materials under study. The relatively high values of the Dietzel (ΔT) and Saad–Poulain (S or H′) thermal stability factors determined using a differential thermal analysis (DTA) indicate the good thermal stability of the glass matrix, which gradually improves with the content of the active dopant. The temperature dependence of optical spectra in the temperature range 300–675 K for the VIS–NIR region was investigated. The involved Pr³⁺ optical transition intensities and relaxation dynamic of the praseodymium luminescent level were determined. The ultrashort femtosecond pulses were utilized to examine a dynamic relaxation of the praseodymium luminescent levels. Although the measured emission of the Pr³⁺ active ions in the studied glass encompasses the quite broad spectral region, the observed luminescence may only be attributed to ³P_J excited states. As a result, the observed decrease in the experimental lifetime for the ³P₀ level along with the increasing activator content was identified as an intensification of the Pr–Pr interplay and the associated self-quenching process. The maximum relative sensitivities (S_r) estimated over a relatively wide temperature range are ~0.46% K⁻¹ (at 300 K) for FIR (I₅₃₀/I₄₉₇) and 0.20% K⁻¹ (at 600 K) for FIR (I₆₃₀/I₄₉₇), which seems to confirm the possibility of using investigated glasses in optical temperature sensors. Full article