Search Results (303)

Understanding the spatiotemporal evolution and driving mechanisms of soil salinization in the Yellow River Delta is a key research focus in the comprehensive utilization of saline–alkali land. Taking Zhanhua District as the study area, this study extracted soil salinization information using four remote sensing salinity index models (SDI1, SDI2, SDI3, SDI4). Model accuracy was evaluated, and the optimal model (SDI1, with an overall accuracy of 86.21%) was selected to analyze the spatiotemporal dynamics of soil salinization from 1993 to 2023. The XGBoost-SHAP framework was then applied to identify and interpret the driving factors of salinization. Furthermore, future soil salinization trends under climate change were projected based on four scenarios from the Sixth Coupled Model Intercomparison Project (CMIP6), including SSP1-2.6 (low forcing), SSP2-4.5 (medium forcing), SSP3-7.0 (medium-to-high-forcing), and SSP5-8.5 (high forcing). The results show the following: (1) Spatially, soil salinization in Zhanhua District exhibits a pattern of being “lighter in the south and heavier in the north.” Over the past 30 years, salinization has undergone a phased evolution characterized by a transition from “severe in the north and mild in the south” to “overall expansion” and finally to “improvement in the north and optimization in the south,” while the proportional structure of salinization severity levels has remained relatively stable. (2) Among the driving factors, evaporation is the dominant contributor (SHAP value = 0.3357), followed by precipitation (0.1732) and population density (0.1518). Soil moisture, land use, and temperature exert moderate influences, while nighttime light intensity, slope, and elevation contribute relatively less. Overall, soil salinization is jointly controlled by climatic factors and human–nature interactions. (3) Among the future climate scenarios, the SSP1-2.6 low-emission scenario exhibits the most pronounced mitigation trend, with a further reduction in salinization intensity projected by 2100. This study provides a scientific basis and data support for formulating soil salinization control and saline–alkali land management strategies in Zhanhua District and the Yellow River Delta. Full article

Studies have shown that oceanic surface-water salinity varies across the globe and changes over time, while atmospheric water-vapor levels have also increased in recent decades. Evaporation from ocean and inland waters is controlled primarily by meteorological forcing, but the thermodynamic state of the water body also matters. In saline waters, dissolved solutes reduce water activity and thereby reduce the equilibrium tendency of water molecules to enter the vapor phase. In this study, the authors’ coefficient-less aqueous osmotic potential equation was used to examine the thermodynamic effect of representative oceanic salinity differences on evaporative tendency. Calculations were made for recorded surface-water salinities ranging from 31 to 38 kg·m⁻³ of dissolved solutes at an average temperature of 20 °C. Computed osmotic potentials ranged from −2.257 to −2.708 MPa. The corresponding semi-permeable membrane interface pressures ranged from 8.935 to 8.484 MPa, indicating an approximately 5% difference across the selected oceanic salinity range. The interface pressure calculated for solute-free water (11.192 MPa) was more than 24% higher than for the seawater cases considered. These results suggest that salinity acts as a secondary thermodynamic modifier of evaporation potential, whereas radiative, aerodynamic, humidity, and temperature controls remain dominant in determining actual evaporation fluxes. The results also indicate that freshwater bodies and changing land-based evaporative sources may contribute differently to atmospheric water vapor than saline ocean waters. The framework presented here is intended to complement, rather than replace, established evaporation formulations by clarifying how salinity-related osmotic effects can modify the water-side boundary condition. Full article

To address the difficulty of simultaneously achieving effective heat dissipation and adequate humidification in open-cathode air-cooled proton exchange membrane fuel cells (PEMFCs) under medium and high power operation, this study proposes a hydrothermal management strategy based on coordinated ultrasonic atomization humidification and fan speed regulation. A three-dimensional single-cell multiphysics model is developed and validated using a 300 W experimental platform. The effects of atomization frequency and water temperature on stack performance and internal hydrothermal distribution are systematically investigated. Results show that ultrasonic atomization provides inlet precooling, latent heat absorption, and active region humidification, thereby improving hydrothermal uniformity within the stack. Under the optimal condition of 100 kHz and 55 °C, the peak stack power increases by 21.0% to 319.00 W, while voltage consistency and surface temperature uniformity are also improved. Analysis based on the Stokes number and Dalton’s law of partial pressures indicates that the optimum results from a balance between suppressing droplet agglomeration and inertial deposition, and limiting oxygen dilution caused by excessive water vapor. The proposed strategy provides a compact and practical approach for improving the stability, uniformity, and efficiency of air-cooled PEMFCs. Full article

This study investigates the development of mixed matrix membranes based on polyethersulfone incorporated with attapulgite for gas separation applications, addressing the existing gap regarding the use of this mineral in dense membranes obtained exclusively by solvent evaporation and its combined effects on microstructure and transport. The membranes were prepared by phase inversion via solvent evaporation, using solvent/polymer ratios of 75/25 and 80/20 and a thickness of 0.25 mm. The solutions were evaluated in terms of viscosity, and the membranes were characterized by structural techniques such as X-ray diffraction (XRD), atomic force microscope (AFM), contact angle, mechanical properties (tensile testing), and water vapor permeation. The results showed that attapulgite incorporation promoted a reduction in surface roughness (up to ~40%) and a decrease in contact angle (from ~89° to ~68°), indicating increased hydrophilicity. In addition, water vapor permeability was influenced in a non-linear manner, with optimized performance observed at 3 wt% filler loading. Solution viscosities remained within ranges suitable for processing. Structural analyses indicated compatibility between the phases, while morphology changes dependent on filler content were decisive for transport behavior. It is concluded that attapulgite is a promising additive for fine-tuning membrane properties, enabling optimization of the sorption–diffusion balance and improvement of membrane performance in separation applications. Full article

The crystal structure regulation of Ti₃O₅ by Al₂O₃ doping and its effect on the optical properties of TiO₂ films prepared by electron beam evaporation were systematically studied. Ti₃O₅ coating materials with different Al₂O₃ doping contents (0–50 at%) were prepared by vacuum melting, and the corresponding TiO₂ films were deposited on K9 glass substrates via electron beam vacuum evaporation. The phase structure, phase transition temperature, chemical composition and optical properties of the materials and films were characterized by XRD, DSC, EDS, XPS, UV-Vis and AFM. Results show that Al₂O₃ doping induces the phase transition of Ti₃O₅ from a room-temperature stable β-phase to a high-temperature stable λ-phase, with complete transition at 5 at% doping. Al³⁺ with a smaller ionic radius causes lattice contraction and local distortion of Ti₃O₅, enabling stabilization at room temperature of the λ-phase. For TiO₂ films, 12.5 at% doping is the optimal state with the stable composition transfer under this condition. With the increase in Al₂O₃ doping content, the refractive index and extinction coefficient of TiO₂ films decrease continuously, while the optical band gap and surface roughness show an increasing trend. The changes in optical properties are mainly ascribed to the low refractive index of Al₂O₃, lattice compressive strain effect and oxygen vacancy passivation induced by Al³⁺. This study clarifies the regulation effect of Al₂O₃ doping on Ti₃O₅ phase transition and TiO₂ film optical properties, and provides theoretical basis and experimental reference for the doping modification of TiO₂ films and their practical applications in consumer electronics and optical filter devices. Full article

Background: Evaporative water loss from burn wounds is a major but often neglected component of early fluid requirements. Despite its physiological importance, no dedicated review has quantified acute post-burn evaporative water loss (TEWL) and its interaction with modern resuscitation strategies in over 40 years. Recent mass-casualty burn events in specialized centers have re-emphasized the clinical importance of accurate early fluid balance, which is particularly challenging. Methods: A scoping review (PRISMA-ScR) of historical quantitative studies and 23 contemporary (2015–2025) adult major-burn resuscitation cohorts was conducted. Expected TEWL was derived from Lamke benchmarks; interstitial edema was estimated from the only available regression of simultaneous fluid input and 24 h weight change. A novel TEWL/edema ratio was tested against resuscitation volume (mL/kg/%TBSA) and the established input/output (I/O) ratio. Results: In the acute phase, the median TEWL normalized to total body surface area was 71 mL/m²/h [52–79 mL/m²/h], allowing for calculation of the TEWL/edema ratio. The TEWL/edema ratio was inversely correlated with the resuscitation fluid dose (R² = 0.811) and the I/O ratio as well (R² = 0.86), crossing unity at 2.85 mL/kg/%TBSA. A ratio > 1 signals high evaporative drive and/or possible under-resuscitation; a ratio < 1 alerts to fluid creep before significant weight gain. Conclusions: The TEWL/edema ratio is the first physiology-grounded, easily calculable resuscitation endpoint that complements urine output by providing insight into whether administered fluid is lost as obligatory evaporation or sequestered as edema. Routine estimation of expected TEWL and early monitoring of the TEWL/edema ratio may help guide goal-directed burn resuscitation, especially when early excision is delayed or impossible. Given the substantial inter-individual variability, the ratio derived from aggregate data should not be interpreted as a patient-specific predictor. Full article

This study aims to reduce the phase transition temperature (PTT) of W-doped vanadium dioxide (VO₂) multilayer thin films. We designed and fabricated two asymmetric multilayer thin film structures; namely, TiO₂/VO₂-5%W/ITO and ITO/VO₂-5%W/TiO₂. The W-doped VO₂-based Trilayer thin films were deposited using an electron beam evaporation combined with the ion-assisted deposition (IAD) technique. An experimental study was conducted on the temperature-dependent residual stress and optical properties of the two asymmetric VO₂-based three-layer structures. The VO₂-based thin films were characterized using UV–Vis–NIR spectrophotometry, Fourier transform infrared spectroscopy (FTIR), Raman spectroscopy, and an improved Twyman–Green interferometer combined with fast Fourier transform (FFT) analysis for residual stress measurement. The trilayer structures incorporated a ~60 nm thick W-doped VO₂ middle layer, which plays a critical role in modulating thermochromic behavior and residual stress evolution. The results show that both trilayer thin films demonstrated excellent optical performance in transmission spectra. Raman spectral analysis revealed a blue shift in the characteristic W-doped VO₂ peaks, accompanied by a decrease in peak intensity as the temperature increased. Heating experiments on asymmetric W-doped VO₂ trilayer thin films revealed that the critical transition temperature of the ITO/VO₂-5%W/TiO₂/B270 trilayer film structure was significantly reduced to 45 °C. This demonstrates the effectiveness of our proposed multilayer film design in improving the PTT of W-doped VO₂ thin films. Analysis of the changes in residual stress of the trilayer thin films during heating experiments revealed that the residual stress shifted from compressive to tensile in the temperature range of 40 °C to 50 °C. The thermal expansion coefficient and biaxial modulus of the TiO₂/VO₂-5%W/ITO trilayer film structure were 5.37 × 10⁻⁶ °C⁻¹ and 295.7 GPa, respectively. In addition, the thermal expansion coefficient and biaxial modulus of the ITO/VO₂-5%W/TiO₂ trilayer film structure were 6.65 × 10⁻⁶ °C⁻¹ and 745.0 GPa. Full article

The conversion of surplus electrical energy into thermal energy represents an effective pathway for increasing the flexibility of renewable-energy systems. This study presents an experimental and numerical assessment of a compact vapor-assisted sensible heat storage unit designed to transform electrical input into stored thermal energy using a controlled evaporation–condensation process inside a vertical steel cylinder. An 800 W immersion heater was employed to generate vapor, while nine temperature sensors monitored the thermal response of the evaporator, enclosure air, and storage medium. Two operating configurations, insulated and non-insulated, were investigated to characterize charging and discharging dynamics. In parallel, CFD simulations performed in ANSYS Fluent were used to analyze coupled heat transfer and phase-change mechanisms. The results demonstrate efficient electrical-to-thermal energy conversion, with rapid temperature rise during charging driven by vapor-assisted convection following the onset of boiling. Experimental data and numerical predictions consistently reveal a transition from conduction-dominated heating to a phase-change-enhanced regime, which accelerates heat distribution and thermal homogenization within the storage unit. Comparative tests further indicate that reduced external losses improve heat retention during discharge. Overall, the combined experimental–numerical approach confirms the capability of the proposed compact system to store electrically generated heat in a stable and repeatable manner, highlighting its potential for daily photovoltaic energy buffering and small-scale renewable-energy applications. Full article

This study aimed to establish normative in-shoe plantar foot temperature patterns across three static postures—lying, sitting, and standing—in healthy individuals, providing a clinically relevant baseline for interpreting in-shoe thermograms in diabetic or peripheral arterial disease (PAD) populations. A single-center prospective study included 20 healthy adults (40 limbs; 22–74 years) who underwent vascular and neurological screening prior to data collection. Plantar temperature was continuously recorded using Tarsos^® Smart Insoles with 21 embedded sensors per foot during three consecutive 10 min phases: supine, sitting, and standing. Data were analyzed for regional differences across the toes, metatarsals, arch, and heel using statistical and visual methods. Distinct posture-related temperature patterns were observed. The arch consistently exhibited the highest temperatures, while the toes remained cooler across all phases. Supine positioning resulted in relatively uniform temperature increases, whereas sitting and standing demonstrated more-stable but region-specific patterns, with slower rates of temperature change and more pronounced regional variation. Compared with barefoot thermography, the in-shoe condition showed greater heat retention and reduced evaporative cooling, highlighting the importance of context-specific baseline data. These findings demonstrate the influence of posture on plantar thermal distribution in the in-shoe environment and support the use of embedded monitoring systems for continuous assessment where surface thermography is not feasible. Full article

Hypersaline culture media used for cultivation of Dunaliella salina represent complex multicomponent aqueous systems whose cooling–heating phase behavior remains insufficiently characterized. In this study, the thermal transitions of two biologically relevant hypersaline media (Artari and Ramaraj) were investigated using differential scanning calorimetry (DSC) and cryomicroscopy. The media were examined at NaCl concentrations of 1.5, 2.0, and 4.0 M, corresponding to moderate to highly concentrated brine conditions comparable to natural salt lakes and evaporative basins. DSC analysis revealed pronounced salinity-dependent suppression of ice crystallization and modification of melting transitions relative to classical NaCl–water systems. Increased NaCl concentration reduced recrystallization during heating and shifted peak temperatures, indicating kinetic and compositional effects in the unfrozen fraction. Rapid cooling promoted formation of partially amorphous phases, consistent with limited vitrification in highly concentrated media. Cryomicroscopy directly confirmed changes in ice morphology, nucleation density, and crystal growth dynamics under varying salinity and thermal histories. The combined calorimetric and microscopic approach demonstrates that complete hypersaline cultivation media exhibit phase behavior that cannot be fully extrapolated from simplified binary systems. These findings provide new insight into the physicochemical stability of multicomponent brines during cooling and highlight the critical role of salinity and thermal history in controlling crystallization pathways in hypersaline aqueous environments. Full article

To support the integration of high shares of renewable energy and enhance the operational flexibility of thermal power systems, thermosyphon have been considered as promising high-efficiency heat transfer components for thermal energy storage applications. In this study, a water-based thermosyphon motivated by molten-salt thermal energy storage scenarios is investigated numerically to clarify its internal heat-transfer behavior under different operating conditions. A two-dimensional CFD model is established based on the Volume-of-Fluid (VOF) multiphase approach coupled with the Lee phase-change model. The effects of heating power (3.5–5.0 kW) and liquid filling ratio (25–40%) on wall temperature distribution and thermal resistance characteristics are systematically analyzed. The results indicate that increasing the filling ratio improves the uniformity of the evaporator wall temperature, and a filling ratio of 40% leads to a relatively favorable liquid distribution and the lowest total thermal resistance within the investigated range. The evaporator thermal resistance exhibits a “decrease–increase” trend with heating power and reaches a minimum value of 1.019 × 10⁻⁴ K/W at 4.5 kW, while the condenser thermal resistance decreases monotonically with in-creasing heating power. This study provides comparative numerical insights into the coupled effects of heating power and filling ratio on thermosyphon performance, offering a reference for the component-level design and parameter selection of heat pipe heat exchangers in molten-salt-related thermal energy storage systems. Full article

Thin liquid film evaporation leverages latent heat and low thermal resistance to achieve superior heat transfer capabilities, making it pivotal for next-generation high-heat-flux thermal management systems. This paper presents a systematic review of the fundamental mechanisms, interfacial transport behaviors, and experimental techniques associated with static thin films and falling liquid films. This work elucidates the complex coupling of Marangoni convection, van der Waals disjoining pressure, and contact line dynamics. These mechanisms collectively govern film stability and the intensity of non-equilibrium phase change in the micro-region. The influence of surface wettability and dynamic contact angle hysteresis on hydraulic replenishment and dry spot formation is critically analyzed, offering insights into optimizing surface engineering strategies. In addition, the review categorizes advanced non-intrusive diagnostics, including optical interferometry, laser-induced fluorescence (LIF), and infrared thermography, evaluating their capacity to resolve spatiotemporal variations in film thickness (ranging from 10 nm to several μm) and temperature under complex boundary conditions. Special attention is directed toward falling film evaporation over horizontal tubes, addressing flow regime transitions and the impact of interfacial shear from external airflow. The work concludes by identifying key challenges in multi-physics coupling and proposing future directions for synchronized diagnostics and adaptive surface design. Full article

The sustainable management of Northern China’s vulnerable agro-pastoral ecotone requires a clearer understanding of how tillage systems affect crop productivity through local soil-climate interactions. Therefore, this study was conducted to quantify and compare the long term effects of different tillage practices on soil hydrothermal regimes, resource use efficiency, and maize yield stability in a semi-arid agroecosystem. A long term five-year field experiment with maize was conducted in this ecotone to assess three tillage methods: no tillage (NT), deep ploughing (DP), and conventional rotary tillage (RT). Seasonal monitoring included soil moisture, temperature, bulk density, and straw cover. Analyses focused on soil water use efficiency (WUE), the production efficiency per soil thermal unit (PEsoil), and pathways affecting theoretical calculated yield. Results show that relative to RT and DP, NT consistently elevated soil water content within the 0–30 cm profile during the growing season, with the most marked increases from pre-sowing to the V12 stage. This water-conserving effect was stronger in wet years, highlighting the role of precipitation in NT’s performance. DP also retained more soil water than RT, particularly in deeper layers, though its effect was less pronounced than NT’s. Regarding temperature, NT lowered the daily mean soil temperature and accumulated growing degree days (GDD) in early growth phases, a result of residue cover buffering thermal changes. Despite reduced heat accumulation, NT achieved the greatest efficiencies for both heat and water use (PEsoil and WUE), showing increases of 62.03% and 16.64% over RT, respectively, without yield penalty. Key mechanisms include permanent straw mulch under NT, which curtails evaporation, promotes water infiltration, and stabilizes soil structure, thereby modulating hydrothermal dynamics. Structural equation modeling indicated that soil water content, ear number per hectare, and hundred-kernel weight directly and positively determined final yield. Tillage methods exerted indirect effects on yield by modifying soil physical traits and microclimatic conditions. In this semi-arid setting, both NT and DP outperformed RT in conserving soil water, moderating soil temperature, and boosting resource use efficiency. These practices present viable strategies for strengthening crop resilience and sustaining productivity amid climatic variability. Full article

Hybrid systems consisting of metal–fullerene composites exhibit intriguing properties but often suffer from thermal instability. With proper control, such instability can be harnessed to enable the formation of sophisticated nanostructures with nanometric precision. These self-organization phenomena are not limited to thermal stimulation alone but can also be triggered by other external stimuli. In this work, we investigate the morphological evolution of thin films composed of evaporated C₆₀ and sputtered nickel mixtures, focusing on how external stimuli influence both their structural and electrical properties. Thin films were prepared under controlled deposition conditions, and their surface morphology was analyzed using advanced characterization techniques. Progressive changes in film morphology were observed as a function of composition and external treatment, highlighting the interplay between metallic and molecular components. In particular, it was observed that, due to the annealing treatment, the sample undergoes strong phase separation, with the formation of structures tens of microns in diameter and an increase in electrical resistance, exhibiting insulating behavior. These findings provide insights into the mechanisms governing hybrid thin film formation and suggest potential applications in electronic, optoelectronic, and energy-related devices. Full article

The COVID-19 pandemic led to an unprecedented slowdown in global economic and transportation activities, offering a unique opportunity to assess the relationship between human activity and atmospheric pollution. This study analyzes global variations in major air pollutants and meteorological conditions during the pandemic period using multi-satellite and reanalysis datasets. Nitrogen dioxide (NO₂) data were obtained from the OMI sensor aboard NASA’s Aura satellite, while carbon monoxide (CO) observations were taken from the MOPITT instrument on Terra. Reanalysis products from MERRA-2 were used to assess CO, sulfur dioxide (SO₂), black carbon (BC), organic carbon (OC), and key meteorological variables, including temperature, precipitation, evaporation, wind speed, and direction. Average concentrations of pollutants for April, May, and June 2020, representing the lockdown phase, were compared with the average values of the same months during 2017–2019, representing pre-pandemic conditions. The difference between these multi-year means was used to quantify spatial changes in pollutant levels. Results reveal widespread reductions in NO₂, CO, SO₂, and BC concentrations across major industrial and urban regions worldwide, consistent with decreased anthropogenic activity during lockdowns. Meteorological analysis indicates that the observed reductions were not primarily driven by short-term weather variability, confirming that the declines are largely attributable to reduced emissions. Unlike most previous studies, which examined local or regional air-quality changes, this work provides a consistent global-scale assessment using harmonized multi-sensor datasets and uniform temporal baselines. These findings highlight the strong influence of human activities on atmospheric composition and demonstrate how large-scale behavioral and economic shifts can rapidly alter air quality on a global scale. The results also provide valuable baseline information for understanding emission–climate interactions and for guiding post-pandemic strategies aimed at sustainable air-quality management. Full article