Search Results (521)

Green technologies are actively being used to produce nanosized zinc oxide, which is in demand for water purification processes to remove pollutants. Despite the success of the green synthesis of ZnO nanoparticles, no scientific approach exists for selecting plant extracts to produce nanoparticles with the desired properties. This study shows that the antioxidant activity of the plant extracts used is a key parameter influencing the properties of the resulting ZnO nanoparticles. This conclusion is based on the results of nanoparticle synthesis with the use of various plant extracts. The antioxidant activity of the extracts increases in the following order: plum–gooseberry–black currant–strawberry–sea buckthorn. The synthesized ZnO nanoparticles were characterized by UV–visible spectroscopy, transmission electron microscopy, and energy-dispersive X-ray spectroscopy. The catalytic properties of ZnO nanoparticles were tested under the degradation of a synthetic methylene blue dye after exposure to UV light. We found that with an increase in the AOA of plant extracts, the size of the nanoparticles decreases, while their photocatalytic activity increases. The smallest (d = 13 nm), most uniform in size (polydispersity index 0.1), and most catalytically active ZnO nanoparticles with a small band gap (2.85 eV) were obtained using the sea buckthorn extract with the highest AOA, pH 10 of the reaction mixture and 0.1 M Zn(CH₃COO)₂∙2H₂O as a precursor salt. ZnO nanoparticles synthesized in the sea buckthorn extract demonstrated the highest dye photodegradation efficiency (96.4%) compared with other nanoparticles. The established patterns demonstrate the “antioxidant activity–size–catalytic activity” triad can be considered as a practical guide for obtaining ZnO nanoparticles of a given size and with given properties for environmental remediation applications. Full article

Porous photocatalysts from agricultural waste, i.e., apricot and peach shell, with titanium dioxide were prepared by a carbonaceous method, the adsorption and photocatalytic degradation and its kinetics about methylene blue (MB) were studied systematically. The properties of the prepared composite sorbents were characterized using Brunauer–Emmett–Teller, surface area, scanning electron microscopy, and energy dispersive spectroscopy analyses. Several key factors, including radiation, pH, temperature, initial MB concentration, contact time, and sorbent dosage, as well as photocatalytic activity were investigated. All the waste-TiO₂ adsorbents showed improved adsorption and photodegradation performance compared to commercial charchoal-TiO₂. The produced materials presented high specific surface areas especially those derived from apricot shell-TiO₂ with a combination of type I and IV adsorption isotherms with a hysteresis loop indicating micro and mesopore structures. In addition, under UV radiation, the composite sorbents exhibited greater MB removal efficiency than non-radiated composite sorbents. The examined conditions have shown the best MB adsorption results at pH greater than 7.5, temperature 30 °C, contact time 120 min, initial concentration 0.5 mg/L MB, and sorbent dosage equal to 2.0 g/L C/MB. The total removal rate of MB is 98.5%, while the respective amount of commercial charcoal-TiO₂ is equal to 75.0%. The kinetic model that best describes the experimental data of MB degradation from the photocatalytic materials is the pseudo-second order model. In summary, this work highlights the effectiveness and feasibility of transforming agricultural waste into carbonaceous composite sorbent for the removal of cationic dyes from wastewater. Future work will involve scaling up the synthesis of the catalyst and evaluating its performance using bed reactors for industrial processes. Full article

This work presents a green chemistry route to obtain titanium dioxide TiO₂ nanoparticles with an average size of about 13.25 nm using lemongrass (Cymbopogon citratus) extract. For these assessments, TiO₂ nanoparticles were added to the coating at concentrations of 1% and 5% w/w on fiber-cement sheets. Self-cleaning evaluation was analyzed by the photodegradation of methylene blue (MB) dye at concentrations of 5, 10, and 20 mg/L applied to the coated sheet, and then exposed to simulated sunlight. The coating containing 5 wt% TiO₂ nanoparticles showed the highest photodegradation, reaching 93.3% after 4 h under simulated sunlight exposure at the lowest MB concentration (5 mg/L). Additionally, average contact angles of 80.4°, 92.03°, and 104.25° were determined for coatings containing 0%, 1%, and 5 wt% TiO₂, respectively. Moreover, the modified 5 wt% TiO₂ exhibited up to 30.9% greater hydrophobicity than the control. Antifungal efficacy against Aspergillus niger and Penicillium was evaluated using the Poisoned Food method with nanoparticles at concentrations of 1 and 3 mg/mL showing a moderate growth inhibition. In conclusion, the versatility demonstrated suggests potential applications such as a nano-additive for aqueous acrylic coatings, improving hydrophobicity, self-cleaning and antifungal properties, which could be attractive to the construction industry. Full article

Titanium oxide (TiO₂) is of great interest in solar cell manufacturing, hydrogen production, and organic compound photodegradation. The synthesis variables and methodology affect the morphology, texture, crystalline structure, and phase mixtures of TiO₂, which, in turn, affect the optical and catalytic properties of TiO₂. In this work, the effect of acetic acid as a catalyst and chelating agent on the morphology, texture, crystal structure, optical properties, and photocatalytic activity of TiO₂ samples obtained using the sol–gel method with sodium dodecyl sulfate (SDS) as a template was investigated. The results indicated that acetic acid not only catalyzes the hydrolysis of the TiO₂ precursor but also acts as a chelating agent, causing a decrease in crystallite size from 18.643 nm (T7 sample, pH = 6.8, without addition of acetic acid) to 16.536 nm (T2 sample, pH = 2). At pH 2 and 3, only the anatase phase was formed (T2 and T3 samples), whereas at pH 5 and 6.8, in addition to the anatase phase, the brookite phase (11.4% and 15.61% for samples T5 and T7, respectively) was formed. The band-gap value of TiO₂ decreased with decreasing pH during synthesis. Although the T2 sample had the highest specific surface area and pore volume (232.02 m²g⁻¹ and 0.46 gcm⁻³, respectively), the T3 sample had better efficiency in methylene blue dye photodegradation because its bird-nest-like morphology improved photon absorption, promoting better photocatalytic performance. Full article

ZnO semiconductor-based photocatalysts are mainly studied for the elimination of toxic textile dyes. Metal-doped ZnO displays better performance for this purpose. Herein, Al-doped ZnO (Al–ZnO) was prepared using the mechanochemical calcination method with varying aluminum concentrations for the degradation of the persistent methylene blue (MB) dye. Various characterization techniques, including XRD, FTIR, FESEM, TEM, UV-DRS, and XPS, revealed the improved properties of 3% Al–ZnO in degrading the MB dye. It exhibits 96.56% degradation of 25 mg/L MB dye under 60 min of natural sunlight irradiation with a catalyst dose of 0.5 g/L at a natural pH of 6.4. A smaller particle size, a lower band gap energy of 3.264 eV, and the presence of oxygen vacancies and defect states all facilitate photocatalytic degradation. Radical scavenger experiments using ascorbic acid (for •O₂⁻), 2-propanol (for •OH), and diammonium oxalate (for h⁺) confirmed the crucial role of superoxide (•O₂⁻) and hydroxyl (•OH) radicals in the degradation mechanism. The achievement of 82.80% MB degradation efficiency at the 4th cycle validates the notable stability and excellent reusability of Al–ZnO. Full article

This study investigated the dielectric and photocatalytic properties of green-synthesized titanium dioxide nanoparticles (TiO₂ NPs), which are widely utilized semiconductor materials known for their excellent optical, structural, and electronic characteristics. The TiO₂ NPs were synthesized via a green precipitation method from the aqueous extract of Cymbopogon proximus. A comprehensive set of analytical techniques—UV–Vis spectroscopy, XRD, FTIR, TEM, EDX, and DLS—was employed to determine their optical response, crystalline structure, functional groups, morphology, elemental composition, and particle size distribution. UV–Vis analysis revealed a characteristic absorption peak at 327 nm, and the band gap energy, calculated via the Tauc plot method, was 3.16 eV. The XRD results confirmed the formation of a tetragonal TiO₂ phase with an average crystallite size of approximately 4 nm. TEM images further supported the spherical to quasitetragonal morphology and revealed that the aggregated clusters formed conjoint nanostructures. The photocatalytic activity of the TiO₂ NPs was evaluated using a 0.5 mM RhB dye solution under UV–visible irradiation. The synthesized nanoparticles achieved a photodegradation efficiency of 97% after 50 h, with a corresponding rate constant of 0.073402 h⁻¹, indicating their potential for effective photocatalytic pollutant removal. Furthermore, the dielectric behavior of the TiO₂ NPs was examined at room temperature. The material exhibited a high dielectric constant at low frequencies due to interfacial (Maxwell–Wagner) polarization, along with frequency-dependent AC conductivity attributed to charge-carrier hopping mechanisms. These dielectric properties, combined with strong photocatalytic performance, underscore the suitability of green-synthesized TiO₂ NPs for applications in environmental remediation, energy-storage devices, and advanced technologies. Full article

The pervasive discharge of synthetic dyes into aquatic ecosystems poses a significant threat due to their chemical stability, low biodegradability, and carcinogenicity. Conventional dye remediation methods—such as biological treatments, coagulation, and adsorption—have demonstrated limited efficiency and poor reusability, particularly against resilient azo dyes. Cerium oxide (CeO₂) nanoparticles have gained traction as photocatalysts owing to their redox-active surfaces and oxygen storage capabilities; however, issues like particle agglomeration and rapid charge recombination restrict their catalytic performance. To address these challenges, this study presents the novel synthesis of a graphene oxide–cerium oxide (GO-CeO₂) nanocomposite via a facile in situ hydrothermal approach, using graphite from lead pencils as a sustainable precursor. The composite was structurally characterized using UV–visible spectroscopy, XRD, FTIR, and TEM. The GO matrix not only facilitates uniform dispersion of CeO₂ nanoparticles but also enhances interfacial electron mobility and active site availability. The nanocomposite demonstrated exceptional photocatalytic degradation efficiencies for methyl orange (94%), methyl red (98%), congo red (96%), and 4-nitrophenol (85.6%) under sunlight irradiation, with first-order rate constants significantly exceeding those of pure CeO₂. Notably, GO–CeO₂ retained strong catalytic activity over four degradation cycles, confirming its recyclability and structural stability. Total organic carbon (TOC) analysis revealed 79% mineralization of methyl orange, outperforming CeO₂ (45%), indicating near-complete conversion into benign byproducts. This work contributes a scalable, low-cost, and highly active heterogeneous photocatalyst for wastewater treatment, combining green synthesis principles with improved photodegradation kinetics. Its modular architecture and reusability make it a promising candidate for future environmental remediation technologies and integrated photocatalytic systems. Full article

In this paper, by employing an eco-friendly and green approach, semiconductor CuO/ZnO nanocomposite are synthesized using an aqueous extract of Urtica urens. FT-IR, XRD, TEM, SAED, EDX, TGA, and UV-Vis spectroscopy were used for semiconductor characterization. The data revealed the successful formation of crystalline spherical nanocomposites with sizes ranging from 5 to 45 nm. The main components of the synthesized nanocomposites were Cu, Zn, and O, which had different weights and atomic percentages. The maximum absorbance of nanocomposites was 358 nm, with a direct bandgap of 2.25 eV, which is suitable for photocatalysis under visible light. The maximum photocatalytic activity of the synthesized semiconductor nanocomposites for photodegradation of methylene blue dye was 95.8%, where it was 44.5% and 65.5% for monometallic CuO and ZnO, respectively. The optimum conditions for maximum photocatalytic activity were a pH of 9, a dye concentration of 5 mg L⁻¹, and nanocomposite concentration of 1.0 mg mL⁻¹ after 70 min. The reusability of the synthesized semiconductor was promising for the fourth cycle, with a reduced capacity of 5%. Complementary investigations, antimicrobial activity and cytotoxic activity, were performed to increase the application of semiconductor nanocomposites. The data revealed the promising activity of the nanocomposite against E. coli, P. aeruginosa, B. subtilis, S. aureus, C. parapsilosis, C. albicans, and C. tropicalis with low MICs ranging between 50 and 25 µg mL⁻¹. Additionally, compared with normal cell line, the synthesized nanocomposite targeted the cancer cell line HepG2 with a low IC50 value of 69.9 µg mL⁻¹ (vs. IC50 220 µg mL⁻¹ of normal cell line HFB4). Overall, the green-synthesized semiconductor CuO/ZnO nanocomposite showed promising activity as environmental contaminant cleaner and was integrated with antimicrobial and in vitro cytotoxic activities. Full article

The development of cheap and efficient photocatalysts for the degradation of organic pollutants in textile printing and dyeing wastewater is of great importance for addressing environmental issues, although it remains challenging. In this study, nano-CuS particles were doped on cotton linter aerogels using a straightforward method for the degradation of methylene blue (MB) and organic pollutants in textile wastewater. Material morphology and structure were analyzed using XRD, SEM/EDS mapping, XPS, BET surface area measurements, and UV-Vis spectroscopy, while their performance was evaluated through various tests. The results demonstrated that a 10 mg catalyst material achieved complete degradation of a 20 mL methylene blue solution (15 mg/L) within 120 min. Moreover, the degradation rates of two types of textile wastewater, reactive red wastewater and reactive yellow wastewater, were both above 90% within 120 min and reached complete degradation within 150 min using the 10 mg catalyst material. The experimental results demonstrate that copper sulfide nanoparticles anchored in cotton linter carbon aerogel can increase the contact area of the photocatalytic reaction system, improve the photoelectron transfer, and thus enhance the photocatalytic reaction efficiency, providing a useful foundation for developing economical photocatalysts and effective dye degradation technologies. Full article

Chromophore domains were proposed in a previous work as the mediators of self-healing of optical properties in dye-doped polymers. A statistical mechanical model based on domains matches all observed self-healing dynamics as a function of dye concentration, temperature and light intensity. This suggests that domains are responsible. However, there is no direct observation of domains, nor has their physical morphology been determined. This work reports the first observation of domains in a self-healing polymer using resonant soft X-ray scattering (RSoXS), which gives a domain size in the range of 39.3 Å to 62.8 Å. This range includes the domain model’s prediction of an average domain size of roughly 30 molecules, which is about 56 Å, if the molecules form a loosely packed ball. X-ray scattering of samples of concentration spanning from neat polymer to the saturation limit of disperse orange 11 (DO11) dye in poly(methyl methacrylate) (PMMA) polymer shows domains in the expected size scales, with the mode of the effective scattering width varying little with concentration. However, for constant domain shape, the mode peak would decrease in q with increasing concentration, according to the domain model. This work suggests that the domain shape might change with concentration, which warrants further investigations of domain topology and geometry. The important evidence presented in this work is the direct experimental observation of domains, which is central to self-healing models. Full article

The development of materials for the remediation and monitoring of water environments remains a significant challenge in the field of environment and materials science. In this study, a nickel-based coordination polymer, [Ni(L)(H₂O)₃]_n·nH₂O (1), was synthesized employing 4,4′-(1H,1′H-[2,2′-biimidazole]-1,1′-diyl)dibenzoic acid (H₂L). Single-crystal X-ray diffraction analysis showed that L²⁻ ligands connect Ni²⁺ ions into 1D Z-shaped chains via two coordination modes. The chains are further assembled into a 3D supramolecular structure through hydrogen bonding interactions. The photocatalytic test showed that complex 1 could effectively degrade the organic dye methylene blue (MB). Under the conditions of catalyst dosage 5 mg, MB initial concentration 20 ppm and pH 7, the degradation efficiency reached 87.7% within 180 min. In addition, complex 1 can be used for the electrochemical detection of norfloxacin (NOR) by differential pulse voltammetry (DPV), exhibiting a linear response in the concentration range of 2–197 μM and the detection limit (LOD) of 1.74 μM. These results demonstrate that complex 1 has bifunctional properties of photocatalytic degradation of organic dyes and electrochemical sensing of antibiotic NOR, making it a promising candidate material for the synergistic treatment of complex pollutants. Full article

In the aspect of water purification, a photoactive hybrid material based on reduced graphite oxide (RGO) with covalently, coordinatively, and through van der Waals interactions bonded zirconium(IV) phthalocyanine (PcZr) is proposed. In the material, the phthalocyanine complex plays the role of photosensitizer, while RGO is considered a carrier, ensuring high surface area and supporting PcZr activation. The central metal atom of PcZr directly interacts with lateral active oxygen-containing surface groups of graphite oxide, mainly –OH and –COOH. Thus, the proposed method of synthesis under solvothermal conditions allowed obtaining a relatively high concentration of the dye (0.2 wt.%) in the system based on a partially reduced and exfoliated graphite oxide. Optical studies confirmed the presence of PcZr through absorption and luminescence spectra. Additionally, effective generation of reactive oxygen species was demonstrated by testing the transformation of a dye indicator (diphenylisobenzofuran). Photocatalytic activity of the system was confirmed by photooxidizing selected organic dyes (methylene blue, Rhodamine B, Brilliant Green, and Eriochrome Black T) in a water medium, tested in slightly acidic conditions under red light. The greatest overall decrease in absorption during the photodegradation test was observed for Brilliant Green, reaching 88% after 3 h of irradiation. Full article

Metal-organic frameworks (MOFs), a class of crystalline porous materials featuring a high specific surface area, tunable pore structures, and functional surfaces, exhibit remarkable potential in fluorescent sensing. This review systematically summarizes recent advances in the construction strategies, sensing mechanisms, and applications of MOF-based fluorescent sensors. It begins by highlighting the diverse degradation pathways that MOFs encounter in practical applications, including hydrolysis, acid/base attack, ligand displacement by coordinating anions, photodegradation, redox processes, and biofouling, followed by a detailed discussion of corresponding stabilization strategies. Subsequently, the review elaborates on the construction of sensors based on individual MOFs and their composites with metal nanomaterials, MOF-on-MOF heterostructures, covalent organic frameworks (COFs), quantum dots (QDs), and fluorescent dyes, emphasizing the synergistic effects of composite structures in enhancing sensor performance. Furthermore, key sensing mechanisms such as fluorescence quenching, fluorescence enhancement, Stokes shift, and multi-mechanism coupling are thoroughly examined, with examples provided of their application in detecting biological analytes, environmental pollutants, and food contaminants. Finally, future directions for MOF-based fluorescent sensors in food safety, environmental monitoring, and clinical diagnostics are outlined, pointing to the development of high-performance, low-cost MOFs; the integration of multi-technology platforms; and the construction of intelligent sensing systems as key to enabling their practical deployment and commercialization. Full article

The increasing discharge of organic pollutants such as dyes and antibiotics poses severe threats to aquatic ecosystems and human health. Conventional wastewater treatment methods are often limited by high energy consumption, secondary pollution, or low efficiency under visible light. It is crucial to design novel photocatalysts that can simultaneously utilize visible photons and enable swift transport of photoinduced charge carriers to drive contaminant decomposition. Herein, novel BiOCl/MIL-121 composites were synthesized via a straightforward hydrothermal route. A suite of complementary microscopic and spectroscopic analyses, including SEM, TEM, XRD and XPS, were employed to elucidate the material’s composition. Furthermore, collective evidence from spectroscopic and electrochemical analyses confirms markedly improved light absorption and charge separation efficiency within the BiOCl/MIL-121 photocatalyst. The 5% BiOCl/MIL-121 composite achieved 93.7% removal of Rhodamine B in 60 min, exhibiting a high photocatalytic degradation rate. Similarly, 5% BiOCl/MIL-121 photodegraded 80.4% of tetracyclin, which was much better than that of BiOCl. A plausible interfacial charge-transfer mechanism was deduced from the band structure of the 5% BiOCl/MIL-121 composite and experimental evidence from radical scavenger studies. This study provides an effective strategy for constructing a composite photocatalyst and offers a green way for the efficient degradation of organic pollutants. Full article