Search Results (13)

Water-based lubricants (WBLs) are increasingly being considered for electrified drivetrain applications; however, their electrochemical stability toward bearing steels remains insufficiently understood. This study evaluated the corrosion behavior of through-hardened AISI 52100 bearing steel in novel WBLs to elucidate the corrosion kinetics and surface degradation mechanisms. Round steel disks were cleaned and tested in 50 wt% aqueous dilutions of glycerol, ethylene glycol (MEG), polyethylene glycol (PEG), and polyalkylene glycol (PAG). Electrochemical measurements were conducted using a three-electrode cell in accordance with ASTM G3-14, employing open circuit potential (OCP), linear polarization resistance (LPR), electrochemical impedance spectroscopy (EIS), and potentiodynamic polarization curves. Among the uninhibited fluids, DI water exhibited the highest corrosion current density (19.85 µA/cm²), while glycerol- and PEG-based systems showed the lowest values (0.79 and 0.85 µA/cm², respectively), attributed to organic adsorption at the steel/electrolyte interface. EIS analysis revealed a single charge-transfer-controlled process across all fluids, consistent with a weak, non-passive interfacial oxide whose protective character is modulated by organic adsorption. The addition of NaNO₃ produced divergent effects depending on the base fluid chemistry: the corrosion activity was reduced in DI water and glycerol systems through enhanced passivation, while PEG- and PAG-based formulations showed increased corrosion current densities and reduced charge transfer resistance, attributed to competitive disruption of the polymer boundary layer by nitrate ions. Surface characterization by SEM/EDAX and white-light interferometry corroborated the electrochemical findings, revealing fluid-dependent corrosion morphologies ranging from uniform attack in DI water to localized pitting in polymer-based systems, with NaNO₃ shifting the corrosion mode in PEG/PAG systems from localized to combined localized and uniform attack. These findings highlight the critical role of fluid chemistry in controlling corrosion processes in water-based lubricants and provide mechanistic insight for the development of corrosion-stable formulations for high-performance electrified drivetrain applications. Full article

A multibody simulation model for deep-groove ball bearings is presented. The model considers friction in both the raceway and cage contacts, resulting from radial and axial loads. The model is validated against experimental measurements for a 6319 bearing under oil-bath lubrication over a speed range of 500–3000 min⁻¹ and two load ratios ($C/P=10$ and 6.5). Predicted friction torques show good agreement with measurements, with deviations between 5.5% and 22% at moderate speeds. In addition, electrical contact capacitances are calculated for a 6208 bearing and compared with an analytical approach, showing deviations in the range of 10–14%. Beyond friction prediction, the fully dynamic approach enables time-resolved analysis of roller kinematics and the identification of instability limits under axial excitation. The developed tool therefore enables reliable bearing loss prediction, supports efficiency-oriented drivetrain design, and provides a basis for electro-tribological and stability investigations. Full article

In electric vehicle (EV) drivetrains, lubricant films must not only mitigate friction and wear but also manage stray currents to safely dissipate stray charge and avoid micro-arcing. This study directly compares how a conventional antiwear additive (ZDDP) and a long-chain, ashless, sulfur-free phosphite ester (Duraphos AP240L) manage this balance under current-carrying boundary lubrication conditions. Reciprocating steel-on-steel tests were conducted at fixed load and speed with applied current densities of 0, 0.02, and 42.4 A/cm². Friction and four-probe electrical contact resistance (ECR) were measured in situ, and impedance of tribofilms was measured over a 1–10⁵ Hz range after friction test. In the presence of ZDDP, ECR initially increased and then decreased to a value that was as low as the initial direct contact of two solid surfaces or even lower sometimes. During the initial stage with high ECR, a well-defined impedance semicircle was observed in the Nyquist plot; after forming the tribofilm with low ECR, frequency dependence of impedance could not be measured due to the very low resistance. The decrease in ECR suggested a structural evolution of the anti-wear film on the substrate. However, post-test wear analysis indicated that the formation of this film was accompanied by tribochemical polishing of the countersurface and sometimes pitting of the substrate, which may have been due to localized electrical discharge producing trenches deeper than ~0.5 µm; in additive-free base oil, wear was dominated by ploughing with micro-cutting of the substrate. In contrast, AP240L performed better in terms of friction and wear, showing a remarkable ~30% lower coefficient of friction, while the overall cycle dependence of ECR was similar to the ZDDP case. AP240L showed negligible boundary film controlled wear producing a shallow, smooth track (depth < 0.2 µm) during the friction test, and there was no sign of electrical arc damage. These findings support long-chain, ashless, sulfur-free phosphite esters as promising candidates for EV boundary lubrication where both mechanical and electrical protection are required. Full article

Loss of lubrication in aeronautic drivetrains can lead to catastrophic gearbox failure, and drivetrains must be tested to prove their resistance to loss of lubrication. Research led to a better understanding of the modes of action, interdependencies, and effective measures to optimize drivetrains for a loss of lubrication event. However, there are currently no calculation methods available, so gear design against loss of lubrication is mainly based on experience. This study proposes a novel calculation method that builds upon the scuffing load calculation from ISO/TS 6336-21 to allow for scuffing safety calculation for cylindrical gears facing loss of lubrication. The proposed method synthesizes existing knowledge in the context of loss of lubrication and incorporates further research results concerning the friction, temperature, and scuffing of gears. The calculation method considers relevant gear design aspects and enables estimation of the time-to-failure. A calculation study is used to compare different measures for cylindrical gears facing loss of lubrication. The results demonstrate the remarkable potential for enhancing loss of lubrication performance through increased oil share in the fluid flow, the application of coatings, the adoption of low-loss gear designs, the use of low-friction lubricants, and the incorporation of additives that increase the scuffing temperature. Full article

When exposed to high contact pressure and shear conditions, the sliding and/or rolling contact interfaces of moving mechanical systems can experience significant friction and wear losses, thereby impairing their efficiency, reliability, and environmental sustainability. Traditionally, these losses have been minimized using high-performance solid and liquid lubricants or surface engineering techniques like physical and chemical vapor deposition. However, increasingly harsh operating conditions of more advanced mechanical systems (including wind turbines, space mechanisms, electric vehicle drivetrains, etc.) render such traditional methods less effective or impractical over the long term. Looking ahead, an emerging and complementary solution could be tribocatalysis, a process that spontaneously triggers the formation of nanocarbon-based tribofilms in situ and on demand at lubricated interfaces, significantly reducing friction and wear even without the use of high-performance additives. These films often comprise a wide range of amorphous or disordered carbons, crystalline graphite, graphene, nano-onions, nanotubes, and other carbon nanostructures known for their outstanding friction and wear properties under the most demanding tribological conditions. This review highlights recent advances in understanding the underlying mechanisms involved in forming these carbon-based tribofilms, along with their potential applications in real-world mechanical systems. These examples underscore the scientific significance and industrial potential of tribocatalysis in further enhancing the efficiency, reliability, and environmental sustainability of future mechanical systems. Full article

Electric motors play a decisive role in electric vehicles by converting electrical energy into mechanical motion across various drivetrain components. However, failures in these motors can interrupt the motor function, with approximately 40% of these failures stemming from bearing issues. Key contributors to bearing degradation include shaft voltage, bearing current, and electric discharge material spalling current, especially in motors powered by inverters or variable frequency drives. This review explores the tribological and vibrational aspects of bearing currents, analyzing their mechanisms and influence on electric motor performance. It addresses the challenges faced by electric vehicles, such as high-speed operation, elevated temperatures, electrical conductivity, and energy efficiency. This study investigates the origins of bearing currents, damage linked to shaft voltage and electric discharge material spalling current, and the effects of lubricant properties on bearing functionality. Moreover, it covers various methods for measuring shaft voltage and bearing current, as well as strategies to alleviate the adverse impacts of bearing currents. This comprehensive analysis aims to shed light on the detrimental effects of bearing currents on the performance and lifespan of electric motors in electric vehicles, emphasizing the importance of tribological considerations for reliable operation and durability. The aim of this study is to address the engineering problem of bearing failure in inverter-fed EV motors by integrating electrical, tribological, and lubrication perspectives. The novelty lies in proposing a conceptual link between lubricant breakdown and damage morphology to guide mitigation strategies. The study tasks include literature review, analysis of bearing current mechanisms and diagnostics, and identification of technological trends. The findings provide insights into lubricant properties and diagnostic approaches that can support industrial solutions. Full article

Efficient lubrication lowers friction, wear, and energy losses in automotive drivetrain components. Advanced lubricants are key to sustainable transportation performance, durability, and efficiency. This study analyzes the tribological performance of Group III base oil with CuO and ZnO nanoadditive mixtures. These additives enhance the performance of Group III base oils, making them highly relevant for automotive lubricant applications. An Optimol SRV5 tribometer performed ball-on-disk sliding contact tests with 100Cr6 steel specimens subjected to a 50 N force and a temperature of 100 °C. The test settings are designed to mimic the boundary and mixed lubrication regimes commonly seen in the automobile industry. During the tests, the effect of nanoparticles on friction was measured. Microscopic wear analysis was performed on the worn specimens. The results demonstrate that adding 0.3 wt% CuO nanoparticles to Group III base oil achieves a 19% reduction in dynamic friction and a 47% decrease in disk wear volume compared to additive-free oil. Notably, a 2:1 CuO-to-ZnO mixture produced synergy, delivering up to a 27% friction reduction and a 54% decrease in disk wear. The results show the synergistic effect of CuO and ZnO in reducing friction and wear on specimens. This study highlights the potential of nanoparticles for lubricant development and automotive applications. Full article

The widespread adoption of electric vehicles (EVs) has introduced new challenges in drivetrain lubrication, particularly concerning electrical corrosion, frictional wear, and hydrogen embrittlement. While polyalphaolefin (PAO)-based lubricants are commonly used, they struggle under high-speed and high-torque conditions. In contrast, polyphenyl ether (PPE)-based lubricants offer superior wear resistance and effectively suppress hydrogen generation, making them promising for EV applications. This study examines the effects of current direction and magnitude on tribofilm formation and frictional behavior in a PPE-lubricated environment. The results show that PPE exhibits unique tribofilm adhesion characteristics influenced by electrical conditions, unlike PAO. Surface analysis reveals that the tribofilm mainly consists of amorphous carbon, and friction under an electrical bias induces PPE oxidation, with oxidation products forming more readily at the positive electrode. Tribofilm formation correlated with increased friction and wear, particularly under currents of 10 mA or higher. Although PPE is more sensitive to electrical influences than PAO, it exhibits excellent wear resistance and maintains a low coefficient of friction even under electrification. This suggests that PPE could be suitable for lubrication in electrical environments and may serve as a promising lubricant for EV drive systems and similar applications. Full article

Bicycles are one of the most sustainable forms of transportation and sports available today, known for their environmental friendliness, cost-effectiveness, lightweight design, compactness, and health benefits. The efficiency and power transmission of bicycle drivetrains have emerged as crucial concerns for engineers, bicycle manufacturers, and both professional and amateur cyclists. However, research and publications related to bicycle drivetrain systems and their tribological performance are notably limited. There is a lack of systematic reviews on technological progress and recent research works in this field. This paper aims to redress this imbalance by presenting a comprehensive literature review of power transmission and tribology in bicycle drivetrains through assessing an extensive body of theoretical and practical work encompassing bicycle drivetrains and roller chain drive mechanisms and performance. This review comprises an exploration of bicycle drivetrain mechanisms and components, an examination of subjects related to power transmission mechanics and efficiency, and a thorough analysis of tribological factors in bicycle drivetrains, including friction, wear, and lubrication. A particular focus has been put on the performance of roller chain drives. This review consolidates research findings related to power transmission within the bicycle drivetrain systems and outlines some future perspectives in relevant research. Through this review, we aim to shed light on the existing knowledge gaps within bicycle drivetrain research and offer constructive recommendations for advancements in this field. Full article

The tribological performance of nanolubricants in electric drivetrains has gained attention due to the rapid growth of electric vehicles. Nanomaterials, especially those with high thermal conductivity and low electrical conductivity, are favored as lubricant additives for use in electrical conditions. Low-viscosity lubricants, known for their good thermal conductivity, are increasingly being considered for electric powertrains. Combining appropriate nanomaterials with lubricants can optimize nanolubricants for electric drivetrains, with stability, tribocorrosion, and electro-viscosity being key factors. Traditional tribometers, when modified to apply external electrical power, allow testing of nanolubricants under electrical conditions, providing insights into their behavior with positive and/or negative electrical charges. To achieve accurate and stable results, tribological test systems must be adapted, requiring well-isolated rigs for controlled data collection. This adaptation enables a better understanding of the interaction between nanomaterials and surfaces under lubrication. This paper reviews studies that use modified tribometers to analyze nanolubricant performance under mechanical and electrical conditions and explores the effects of electrical and thermal factors on lubricant properties, nanomaterials, and their mechanisms under triboelectric conditions. Full article

Generally speaking, excessive side thrust and roller slippage are two different aspects affecting cam-roller mechanisms. In novel large-scale hydraulic drivetrains for offshore wind turbines, the highly dynamic nature of these mechanisms combined with the interplay of cyclic loads, frictional torques and inertia promote slippage at the cam-roller interface. At larger scales, the effects of roller inertia become much more pronounced, as the inertia escalates exponentially with the roller’s radius. This study presents a comparative analysis between radial and offset roller followers in novel large-scale hydraulic drivetrains, where offset followers are incorporated to minimize the side thrust. The framework encompasses a comprehensive kinematic and force analysis, to provide the inputs for two lubrication models integrated into the torque-balance equation, where the possibility of slippage is allowed. The findings reveal that the equivalent side thrust can be reduced by 51% with offset followers. Both configurations experience slippage during the low-load phase, but it rapidly diminishes during the high-load phase. This sudden transition in rolling conditions results in a sharp increase in surface temperature and traction force, emphasizing the importance of minimizing sliding at the interface. However, besides the substantial side thrust reduction, offset followers showed superior tribological performance, mitigating undesirable thermal and frictional effects. Full article

Electric vehicle sales are growing globally in response to the move towards a greener environment and a reduction in greenhouse gas emissions. As in any machine, grease lubricants will play a significant role in the component life of these new power plants and drivetrains. In this paper, the role of grease lubrication in electric vehicles (EVs) and hybrid vehicles (HVs) will be discussed in terms of performance requirements. Comparisons of grease lubrication in EVs and HVs for performance requirements to current internal combustion engines (ICEs) will be reviewed to contrast the major differences under different operating conditions. The operating conditions for grease lubrication in these EVs and HVs are demanding. Greases formulated and manufactured to meet specific performance specifications in EVs and HVs, which will operate within these specific electrification components, will be reviewed. Specifically, the thermal and electrified effects from the higher operating temperatures and electromagnetic fields on lubricant degradation, rheology, elastomer compatibility, and corrosion protection of the grease need to be evaluated to accurately meet the performance requirements for EVs and HV. The major differences between EVs and conventional ICEVs can be grouped into the following technical areas: energy efficiency, noise, vibration, and harshness (NVH), the presence of electrical current and electromagnetic fields from electric modules, sensors and circuits, and bearing lubrication. Additional considerations include thermal heat transfer, seals, corrosion protection, and materials’ compatibility. The authors will review the future development trends of EVs/HVs on driveline lubrication and thermal management requirements. The future development of electric vehicles will globally influence the selection and development of gear oils, coolants, and greases as they will be in contact with electric modules, sensors, and circuits and will be affected by electrical current and electromagnetic fields. The increasing presence of electrical parts in EVs/HVs will demand the corrosion protection of bearings and other remaining mechanical components. Thus, it is imperative that specialized greases should be explored for specific applications in EVs/HVs to ensure maximum protection from friction, wear, and corrosion to guarantee the longevity of the operating automobile. Low-viscosity lubricants and greases will be used in EVs to achieve improvements in energy efficiency. However, low-viscosity fluids reduce the film thickness in the driveline application. This reduced film thickness increases the operating temperature and reduces the calculated fatigue life of the bearings. Bearing components for EVs/HVs will be even more crucial as original equipment manufacturers (OEMs) specify these low-viscosity fluids. The application of premium bearing components using low-viscosity grease will leverage materials, bearing geometries, and surface topography to combat the impact of low-viscosity lubricants. In addition, EVs and HVs will create their own NVH challenges. Wind and road noise are more prominent, with no masking noise from the ICE. Increasing comfort, quality, and reliability issues will be more complicated with the introduction of new electrified powertrain and E-driveline subsystems. This paper elaborates on the current development trends and industrial test standard for the specified grease used for electrical/hybrid driveline lubrication. Full article

Economic and societal changes and technological development guide the focus of tribology research. “Classical” tasks, such as the improvement of materials or the tuning of a lubricant, have long been replaced by a function-oriented aggregate design, including specifications defined by needs arising from production and the environment. Tribology faces, among other remarkable changes, a paradigm shift according to the tendency to replace classic internal combustion engine (ICE) drivetrains with electric drives. How tribology will develop, and which research topics will prevail in the future, are being explored by several studies based on the experience of experts. The variety of contributions to journals and conferences provide an indicator of the importance of such tasks or topics. Here, a report on the ECOTRIB 2019—7th European Conference on Tribology held in Vienna, Austria, is presented. From the available information, an even stronger integration of other disciplines into tribology is noticeable, with certain hype in the fields of advanced material technology, sensor integration and the implementation of data science. Measures to rethink tribology from both an organizational and scientific point of view to cope with future tasks are being targeted and comprehensively implemented in the current research program “InTribology”, operated by the Austrian Center of Competence for Tribology (AC²T) in Wiener Neustadt, Austria. Full article