Search Results (158)

To address the difficulty of balancing trajectory-tracking accuracy and yaw stability for distributed-drive four-axle heavy trucks under high-speed and large-curvature cornering conditions, this paper proposes a hierarchical cooperative control strategy. The upper layer employs Sliding Mode Control (SMC) to achieve precise trajectory tracking, while the lower layer integrates a sliding-mode-based Direct Yaw Moment Control (DYC) and a differential braking allocation strategy to enhance vehicle stability. TruckSim–Simulink co-simulation results demonstrate that, under large-curvature scenarios such as S-shaped paths, sharp lane changes, and single-lane transitions, the proposed strategy outperforms the conventional SMC method. Specifically, the maximum lateral deviation is reduced by 19.23–23.02%, the peak heading angle error decreases from 5.3° to 3.5°, the maximum yaw rate drops from 12.6°/s to 4.6°/s (a 63.49% reduction), and the peak sideslip angle at the vehicle’s center of mass converges from 4.6° to 3.8° (a 17.39% decrease). The results indicate that the proposed strategy achieves coordinated optimization of trajectory tracking and yaw stability under high-speed, large-curvature cornering conditions, providing both theoretical support and engineering value for high-dynamic control of distributed-drive heavy trucks. Full article

When operating in the marine environment, floating offshore wind turbines (FOWTs) are subjected to various inflow conditions such as wind, waves, and currents. To investigate the effects of complex inflow conditions on offshore wind farms, an integrated fluid-structure interaction computational and coupled dynamic analysis method for FOWTs is employed. An aero-hydro-servo-elastic coupled analysis model of the NREL 5 MW semi-submersible wind turbine array based on the OC4-DeepCwind platform is established. The study examines the variations in power generation, platform motion, structural loads, and flow field distribution of the FOWT array under different wave incident angles and yaw angles of the first column turbines. The results indicate that the changes in power generation, platform motion, and flow field distribution of the wind farm are significantly influenced by the yaw angle. The maximum tower top yaw bearing torque and the tower base Y-direction bending moment of the wind turbines undergo significant changes with the increase in the angle between wind and wave directions. The study reveals the mechanism of power generation and load variation during yaw control of the FOWT array under misaligned wind and wave conditions, providing a theoretical basis for the future development of offshore floating wind farms. Full article

In this work, the yaw control of large wind turbines is studied. The objective is to analyse how to maximise energy conversion by yawing the rotor in response to wind direction while minimising yaw activity. In order to improve the control performance, three algorithms are used and compared: the classic PI controller, the nonlinear PI controller, and the fractional-order nonlinear PI controller. An adaptive dead-zone and anti-windup procedure for amplitude- and rate-limited actuators are also considered, which helps to reach the main objective. Simulation experiments are carried out on a 20 MW reference wind turbine. The results are very promising, showing clear performance improvements. Full article

To address the issue of limited accuracy in vehicle lateral and longitudinal dynamics control—caused by the strong coupling and nonlinearity between the four-wheel steering and distributed drive systems, particularly under crosswind disturbances—a control method integrating differential geometric decoupling with robust control is proposed. This integrated approach mitigates coupling effects among the vehicle motions in various directions, thereby enhancing overall robustness. The control architecture adopts a hierarchical structure: the upper layer takes the deviation between the ideal and actual models as input and generates longitudinal, yaw, and lateral control laws via robust control; the middle layer employs differential geometric methods to decouple the nonlinear system, deriving the total driver-required driving torque, additional yaw moment, and rear-wheel steering angle; and the lower layer utilizes a quadratic programming algorithm to optimize the distribution of driving torque across the four wheels. Finally, simulation verification is conducted based on a co-simulation platform using TruckSim 2022 and MATLAB R2024a/Simulink. The simulation results demonstrate that, compared to the sliding mode control (SMC) and the uncontrolled scenario, the proposed method improves the driving stability and safety of the four-wheel steering distributed drive vehicle under multiple operating conditions. Full article

Offshore wind turbines (OWTs) operate under harsh marine conditions involving strong winds, waves, and salt-laden air, which increase the risk of excessive vibrations and structural failures such as tower collapse. To ensure structural safety and achieve effective vibration control, accurate modal parameter identification is essential. In this study, a vibration monitoring system was developed, and the Bayesian Spectral Decomposition (BSD) method was applied for the operational modal analysis of a 5.5 MW monopile OWT. The monitoring system consisted of ten uniaxial accelerometers mounted at five elevations along the tower, with two orthogonally oriented sensors at each level to capture horizontal vibrations. Due to continuous nacelle yawing, the measured accelerations were projected onto the structural fore–aft (FA) and side–side (SS) directions prior to modal analysis. Two days of vibration and SCADA data were collected: one under rated rotor speed and another including one hour of idle state. Data preprocessing involved outlier removal, low-pass filtering, and directional projection. The obtained data were divided into 20-min segments, and the BSD approach was applied to extract the primary modal parameters in both FA and SS directions. Comparison with results from the Stochastic Subspace Identification (SSI) technique showed strong consistency, verifying the reliability of the BSD method and its advantage in uncertainty quantification. The results indicate that the identified modal frequencies remain relatively stable under both rated and idle conditions, whereas the damping ratios increase with wind speed, with a more significant growth observed in the FA direction. Full article

To address the poor stability of four-wheel steering vehicles under extreme conditions, this paper proposes a coordinated control strategy for vehicles with four-wheel independent drive. The strategy combines the Active Four-Wheel Steering system with the Direct Yaw Moment Control system. First, a shared steering control model is constructed by considering both the vehicle’s path-tracking performance and handling stability. Based on this model, a control strategy for the four-wheel steering system is proposed using a non-cooperative Nash game. Next, a direct yaw moment controller is designed to improve vehicle lateral stability under dangerous driving conditions. To achieve synergy between rear-wheel steering and direct yaw moment control, a rule-based coordination strategy is introduced to optimize the working intervals of each sub-controller. Finally, experimental verification is performed under double-lane-change and slalom conditions using the CarSim/Simulink hardware-in-the-loop platform. All computations were done in MATLAB R2024a, using specific m-files and Simulink functions for implementation, and the controller was implemented using the Micro-Autobox tool. The results demonstrate that the proposed control strategy significantly enhances vehicle path-tracking accuracy and handling stability under extreme driving conditions. Full article

This paper presents a braking force coordination control strategy for electric vehicles based on a hierarchical control architecture. The proposed strategy integrates electronic brakeforce distribution (EBD), direct yaw control (DYC), anti-lock braking system (ABS), and braking force reconstruction functions to effectively enhance braking stability under brake actuator failure conditions. First, a full-vehicle model is established to investigate the braking force coordination process during braking. Then, by analyzing the coupling relationship between the yaw moment and DYC control, a dynamic ABS/DYC coordination strategy is developed. A dynamic computation model of the braking force limited weight coefficient is established, and a three-level braking force coordination mechanism is constructed according to the braking force limited state of each wheel. This mechanism achieves integrated coordination and reconstruction of longitudinal and lateral braking forces. Considering road adhesion, failure sequence, and failure location, eleven typical verification scenarios are designed. Simulation results show that, compared with uncoordinated control methods, the proposed method not only can effectively handle with muti-wheel failure scenarios, but also can reduce the braking distance by up to 7.05% and the lateral deviation by 26.74%, effectively improving the braking safety of electric vehicles. Full article

Modern aircraft usually employ control allocation to distribute virtual control commands among redundant effectors. Infeasible virtual command can occur frequently due to aggressive maneuvers and limited control authority. This paper proposes a lightweight command scaling law for incremental flight control allocation. The method scales the raw incremental virtual command by a direction-preserving gain $K\in$ [0,1]. It is updated via gradient descent on a Lyapunov function that balances allocation error against deviation from unity gain. The proposed adaptive update law ensures the convergence of K to a value that corresponds to the attainable portion of infeasible commands, independent of the specific allocator used. At the same time, feasible virtual commands will be preserved. Its performance was evaluated through open-loop ray sweeps of the attainable moment set and closed-loop INDI simulations for a yaw-limited eVTOL. The results demonstrate that the adaptive scaling gain closely approximates the linear programming ground truth while offering significantly higher computational efficiency. Furthermore, it effectively mitigates cross-axis coupling, reduces peak excursions, and alleviates rotor saturation. These findings highlight the method’s effectiveness, modularity, and suitability for real-time implementation in aerospace applications. Full article

This paper proposes a coefficient-based method for designing a rocket angular stabilization system that yields an explicit, direct solution for determining the parameters of a PID control law from specified stability and performance indices. Linearized equations of motion in the yaw channel with a PID law are formulated, and the system transfer function and its characteristic polynomial are obtained. Quantitative stability and performance indices are introduced, defined via the coefficients of the characteristic polynomial, and expressed directly through the control law parameters. Based on sufficient conditions for stability and performance, resolving inequalities are derived for the control parameters that meet the prescribed stability and performance requirements. It is shown that the solution set of these inequalities is non-empty; i.e., the problem of finding the required control law parameters always has a solution. In the control-parameter space, the boundaries of the system’s stability and performance regions are explicitly described. A decomposition method and its extension are proposed for the design problem by the required transient process shape and transient time, splitting it into two sequential subproblems: obtaining the required shape and obtaining the required speed. A simple and effective adaptive algorithm is proposed to maintain constant stability and performance indices under variable engine thrust. The results of applying the proposed design methods to the development of a rocket angular stabilization system test stand are presented. Numerical experiments convincingly demonstrate the high effectiveness of the proposed coefficient-based design method—combining sufficient stability and performance conditions with the decomposition approach—for designing the test stand system. Full article

Recently, various forms and purposes of autonomous mobility have been widely developed and commercialized. To control the various iterations of shaped and purposeful mobility, control technology that can adapt to the dynamic characteristics of the mobility and environmental changes is essential. This study presents an adaptive proportional–integral–derivative (PID) controller for longitudinal velocity and yaw rate tracking in autonomous mobility, addressing the aforementioned issue. To design the adaptive PID controller, error dynamics have been designed using error and control input with two coefficients. It is designed that the two coefficients are estimated in real time by recursive least squares with multiple constraints and forgetting factors. The estimated coefficients are used to compute PI gains based on the Lyapunov direct method with constant derivative gain. Multiple constraints, such as value and rate limits, have been incorporated into the RLS algorithm to enhance the control stability. The performance evaluation is conducted through the co-simulation of MATLAB/Simulink and CarMaker under integrated control scenarios, such as longitudinal velocity and yaw rate tracking, for mobility. Full article

To resolve the inherent coupling conflict between trajectory tracking and lateral stability in distributed electric drive buses, this paper proposes a hierarchical cooperative control framework. A simplified two-degree-of-freedom (2-DOF) vehicle model is first established, and kinematically derived reference states for stable motion are computed. At the upper level, a model predictive controller (MPC) generates real-time steering commands while explicitly minimizing lateral tracking error. At the lower level, a proportional integral derivative (PID)-based roll moment controller and a linear quadratic regulator (LQR)-based direct yaw moment controller are designed, with four-wheel torque distribution achieved via quadratic programming subject to friction circle and vertical load constraints. Co-simulation results using TruckSim and MATLAB/Simulink demonstrate that, during high-speed single-lane-change maneuvers, peak lateral error is reduced by 11.59–18.09%, and root-mean-square (RMS) error by 8.67–14.77%. Under medium-speed double-lane-change conditions, corresponding reductions of 3.85–12.16% and 4.48–11.33% are achieved, respectively. These results fully validate the effectiveness of the proposed strategy. Compared with the existing MPC–direct yaw moment control (DYC) decoupled control framework, the coordinated control strategy proposed in this paper achieves the optimal trade-off between trajectory tracking and lateral stability while maintaining the quadratic programming solution delay below 0.5 milliseconds. Full article

A wheeled–legged robot has the advantage of stable and agile movement on flat ground and an excellent ability to overcome obstacles. However, when faced with a narrow footprint, there is a limit to its ability to move. We developed the control moment gyroscope (CMG) unicycle–legged robot to solve this problem. A scissored pair of CMGs was applied to control the roll balance, and the pitch balance was modeled as a double-inverted pendulum. We performed Linear Quadratic Regulator (LQR) control and model predictive control (MPC) in a system in which the control systems in the roll and pitch directions were separated. We also devised a method for controlling the rotation of the robot in the yaw direction using torque generated by the CMG, and the performance of these controllers was verified in the Gazebo simulator. In addition, forward driving control was performed to verify mobility, which is the main advantage of the wheeled–legged robot; it was confirmed that this control enabled the robot to pass through a narrow space of 0.15 m. Before implementing the verified controllers in the real world, we built a CMG test platform and confirmed that balancing control was maintained within $\pm 1^{\circ }$. Full article

This study examines the effects of partial wakes caused by upstream turbine yaw control on the trailing-edge noise of a downstream turbine under stable and neutral atmospheric conditions. Using a combined model coupling the unsteady vortex lattice method (UVLM) with the Curl wake model, calibrated with large eddy simulation data, wake behavior and noise characteristics were analyzed for yaw angles from −30° to +30°. Results show that partial wakes slightly raise overall noise levels and lateral asymmetry of trailing-edge noise, while amplitude modulation (AM) strength is more strongly influenced by yaw control. AM varies linearly with wake deflection at moderate yaw angles but behaves nonlinearly beyond a threshold due to large wake deflection and deformation. Findings reveal that yaw control can significantly increase the lateral asymmetry in the AM strength directivity pattern of the downstream turbine, and that AM characteristics depend on the complex interplay between inflow distribution and convective amplification effects, highlighting the importance of accurate wake prediction, along with appropriate consideration of observer point location and blade rotation, for evaluating AM characteristics of a wind turbine influenced by a partial wake. Full article

To improve the adaptability of 4WID electric vehicles under various operating conditions, this study introduces a model predictive control approach utilizing a neural network for adaptive weight parameter prediction, which integrates four-wheel steering and longitudinal driving force control. To address the difficulty in adjusting the MPC weight parameters, the neural network undergoes offline training, and the Snake Optimization method is used to iteratively optimize the controller parameters under diverse driving conditions. To further enhance vehicle stability, the real-time stability state of the vehicle is assessed using the $\beta -\dot{\beta }$ phase plane method. The influence of vehicle speed and road adhesion on the instability boundary of the phase plane is comprehensively considered to design a stability controller based on different instability degree zones. This includes an integral sliding mode controller that accounts for both vehicle tracking capability and stability, as well as a PID controller, which calculates the additional yaw moment based on the degree of instability. Finally, an optimal distribution control algorithm coordinates the longitudinal driving torque and direct yaw moment while also considering the vehicle’s understeering characteristics in determining the torque distribution for each wheel. The simulation results show that under various operating conditions, the proposed control strategy achieves smaller tracking errors and more concentrated phase trajectories compared to traditional controllers, thereby improving path tracking precision, vehicle stability, and adaptability to varying conditions. Full article

To address the poor trajectory tracking of mining trucks in narrow, high-curvature paths, this study explores the impact of four-wheel steering (4WS) and direct yaw moment control (DYC) on vehicle stability. A validated two-degree-of-freedom 4WS vehicle model was developed. A fuzzy logic controller with dual inputs (yaw rate and yaw angular acceleration) and a single output (compensatory yaw moment) was designed, alongside an optimal torque distribution controller based on tire friction circle theory to allocate the resultant yaw moment. A co-simulation platform integrating TruckSim and MATLAB/Simulink was established, and experiments were conducted under steady-state and double-lane-change conditions. Comparative analysis with traditional front-wheel steering and alternative control methods reveals that the 4WS mining truck with fuzzy-controlled optimal torque distribution achieves a reduced turning radius, enhancing maneuverability and stability. Hardware-in-the-loop (HIL) testing further validates the controller’s effectiveness in real-time applications. Full article