Search Results (137)

In rural Ghana, limited access to affordable, clean cooking fuels drives the need for decentralised waste-to-energy solutions. Anaerobic co-digestion (AcoD) offers a viable route for transforming organic residues into renewable energy, with the added benefit of improved process stability resulting from substrate synergy. This study aims to evaluate the technical feasibility and stabilisation challenges of AcoD, using locally available fruit waste and beet molasses at a secondary school in Bedabour (Ghana). Biological methane potential (BMP) assays of different co-digestion mixtures were conducted at two inoculum-to-substrate (I/S) ratios (2 and 4), identifying the highest yield (441.54 ± 45.98 NmL CH₄/g VS) for a mixture of 75% fruit waste and 25% molasses at an I/S ratio of 4. Later, this mixture was tested in a 6 L semi-continuous AcoD reactor. Due to the high biodegradability of the substrates, volatile fatty acid (VFA) accumulation led to acidification and process instability. Three low-cost mitigation strategies were evaluated: (i) carbonate addition using eggshell-derived sources, (ii) biochar supplementation to enhance buffering capacity, and (iii) the integration of a bioelectrochemical system (BES) into the AcoD recirculation loop. The BES was intended to support VFA removal and enhance methane recovery. Although they temporarily improved the biogas production, none of the strategies ensured long-term pH stability of the AcoD process. The results underscore the synergistic potential of AcoD to enhance methane yields but also reveal critical stability limitations under high-organic-loading conditions in low-buffering rural contexts. Future implementation studies should integrate substrates with higher alkalinity or adjusted organic loading rates to ensure sustained performance. These findings provide field-adapted insights for scaling-up AcoD as a viable renewable energy solution in resource-constrained settings. Full article

Microbial fuel cells (MFCs) are bio-electrochemical systems that harness microorganisms to convert organic pollutants in wastewater directly into electricity, offering a dual solution for sustainable wastewater treatment and renewable energy generation. This paper presents a holistic techno-economic and environmental feasibility assessment of large-scale MFC deployment in Dhaka’s industrial zone, Bangladesh, as a relevant case study. Here, treating 100,000 cubic meters of wastewater daily would require a capital investment of approximately USD 500 million, with a total project cost ranging between USD 307.38 million and 1.711 billion, depending on system configurations. This setup has an estimated theoretical energy recovery of 478.4 MWh/day and a realistic output of 382 MWh/day, translating to a per-unit energy cost of USD 0.2–1/kWh. MFCs show great potential for treating wastewater and addressing energy challenges. However, this paper explores remaining challenges, including high capital costs, electrode and membrane inefficiencies, and scalability issues. Full article

This study focuses on electrical stimulation for composting. Using the PSALSAR method, a comprehensive systematic review analysis identified 22 relevant articles. The examined studies fall into four main systems: electric field-assisted aerobic composting (EAAC), electrolytic oxygen aerobic composting (EOAC), microbial fuel cells (MFCs), and thermoelectric generators (TEGs). Apart from the main systems highlighted above, bioelectrochemically assisted anaerobic composting (AnC_{BE, III}) is discussed as an underexplored system with the potential to improve the efficiency of anaerobic degradation. Each system is described in terms of key materials, composter design, operating conditions, temperature evolution, compost maturity, microbial community, and environmental outcomes. EAAC and EOAC systems accelerate organic matter decomposition by improving oxygen distribution and microbial activity, whereas MFC and TEG systems have dual functioning due to the energy generated alongside waste degradation. These innovative systems not only significantly improve composting efficiency by speeding up organic matter breakdown and increasing oxygen supply but also support sustainable waste management by reducing greenhouse gas emissions and generating bioelectricity or heat. Together, these systems overcome the drawbacks of conventional composting systems and promote future environmental sustainability solutions. Full article

Microbial Fuel Cell (MFC) is a novel bioelectrochemical system that catalyzes the oxidation of chemical energy in organic waste and converts it directly into electrical energy through the attachment and growth of electroactive microorganisms on the electrode surface. This technology realizes the synergistic effect of waste treatment and renewable energy production. A CF-NiO-PANI capacitor composite anode was prepared by loading polyaniline on a CF-NiO electrode to improve the capacitance of a CF electrode. The electrochemical characteristics of the composite anode were evaluated using cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS), and the electrode materials were analyzed comprehensively by scanning electron microscopy (SEM), energy diffusion spectrometer (EDS), and Fourier transform infrared spectroscopy (FTIR). MFC system based on CF-NiO-PANI composite anode showed excellent energy conversion efficiency in potato starch wastewater treatment, and its maximum power density increased to 0.4 W/m³, which was 300% higher than that of the traditional CF anode. In the standard charge–discharge test (C1000/D1000), the charge storage capacity of the composite anode reached 2607.06 C/m², which was higher than that of the CF anode (348.77 C/m²). Microbial community analysis revealed that the CF-NiO-PANI anode surface formed a highly efficient electroactive biofilm dominated by electrogenic bacteria (accounting for 47.01%), confirming its excellent electron transfer ability. The development of this innovative capacitance-catalytic dual-function anode material provides a new technical path for the synergistic optimization of wastewater treatment and energy recovery in MFC systems. Full article

The transition toward sustainable and decentralized energy solutions necessitates the development of innovative bioelectronic systems capable of harvesting and converting renewable energy. Here, we present a novel photo-bioelectrochemical fuel cell architecture based on a biohybrid anode integrating laser-induced graphene (LIG), poly(3,4-ethylenedioxythiophene) (PEDOT), and isolated thylakoid membranes. LIG provided a porous, conductive scaffold, while PEDOT enhanced electrode compatibility, electrical conductivity, and operational stability. Compared to MXene-based systems that involve complex, multi-step synthesis, PEDOT offers a cost-effective and scalable alternative for bioelectrode fabrication. Thylakoid membranes were immobilized onto the PEDOT-modified LIG surface to enable light-driven electron generation. Electrochemical characterization revealed enhanced redox activity following PEDOT modification and stable photocurrent generation under light illumination, achieving a photocurrent density of approximately 18 µA cm⁻². The assembled photo-bioelectrochemical fuel cell employing a gas diffusion platinum cathode demonstrated an open-circuit voltage of 0.57 V and a peak power density of 36 µW cm⁻² in 0.1 M citrate buffer (pH 5.5) under light conditions. Furthermore, the integration of a charge pump circuit successfully boosted the harvested voltage to drive a low-power light-emitting diode, showcasing the practical viability of the system. This work highlights the potential of combining biological photosystems with conductive nanomaterials for the development of self-powered, light-driven bioelectronic devices. Full article

Plastic pollution remains a critical global environmental challenge, with conventional disposal methods contributing to ecosystem degradation. Simultaneously, energy scarcity affects numerous rural communities, limiting development opportunities. This study presents an innovative approach that integrates microbial fuel cells (MFCs) with Klebsiella oxytoca to simultaneously degrade plastic waste and generate bioelectricity. The monitoring results over 40 days revealed optimal performance on day 28, with a peak voltage of 0.714 ± 0.026 V and an electric current of 3.149 ± 0.124 mA. The biocatalyst exhibited an electrical conductivity of 140.466 ± 5.180 mS/cm and an oxidation-reduction potential of 109.519 ± 5.35 mV, indicating efficient electron transfer. Furthermore, the MFCs achieved a maximum power density of 11.391 ± 0.814 mW/cm² with a current density of 5.106 mA/cm², demonstrating their potential for sustainable energy production. Fourier transform infrared (FTIR) analysis confirmed structural modifications in the plastic, with decreased vibrational peaks indicative of polymer degradation. Additionally, scanning electron microscopy (SEM) micrographs revealed porosity and surface cracks, highlighting Klebsiella oxytoca’s biodegradation capacity. These findings establish the viability of bioelectrochemical systems for simultaneous waste remediation and renewable energy generation, paving the way for scalable applications in environmental biotechnology. By coupling microbial degradation with electricity production, this research supports the development of sustainable solutions aligned with the principles of circular economy and climate change mitigation. Full article

The need for sustainable and efficient water decontamination methods has led to the increasing use of redox enzymes such as glucose oxidase (GOx). GOx immobilization on textile supports provides a promising alternative for catalyzing pollutant degradation in bio-Fenton (BF) and bio-electro-Fenton (BEF) systems. However, challenges related to enzyme stability, reusability, and environmental impact remain a concern. This communication paper outlines innovative strategies developed to address these challenges, notably the use of ecotechnologies to achieve efficient GOx immobilization while maintaining biocatalytic activity. Plasma ecoprocesses, amino-bearing biopolymer-chitosan, as well as a bio-crosslinker genipin have been used efficiently on conductive carbon and non-conductive polyester-PET nonwovens. In certain cases, immobilized GOx can retain high catalytic activity after multiple cycles, making them an effective biocatalyst for organic dye degradation (Crystal Violet and Remazol Blue) via bio-Fenton reactions, including total heterogeneous bio-Fention system. Moreover, the conductive carbon felt-based bioelectrodes successfully supported simultaneous pollutant degradation and energy generation in a BEF system. This work highlights the potential of textile-based enzyme immobilization for sustainable wastewater treatment, bio-electrochemical energy conversion, and also for bacterial deactivation. Future research will focus on optimizing enzyme stability and enhancing BEF efficiency for large-scale applications. Full article

Microbial electrolysis cells (MECs) represent a pioneering technology for sustainable hydrogen production by leveraging bioelectrochemical processes. This study investigates the performance of a single-chamber cathodic MEC, where a cation exchange membrane separates the electrically active bioanode from the cathode. The system was constantly fed with a synthetic carbonaceous solution, employing a working potential of +0.3 V vs. SHE and an organic loading rate of 2 gCOD/Ld with a hydraulic retention time of 0.3 d. Notably, no methanogenic activity was detected, likely due to the establishment of an alkaline pH in the cathodic chamber. Under these conditions, the system exhibited good performance, achieving a current density of approximately 115 A/m³ and a hydrogen production rate of 1.28 m³/m³d. The corresponding energy consumption for hydrogen production resulted in 6.32 kWh/Nm³ H₂, resulting in a slightly higher energetic cost compared to conventional electrolysis; moreover, an average energy efficiency of 85% was reached during the steady-state condition. These results demonstrate the potential of MECs as an effective and sustainable approach for biohydrogen production by helping the development of greener energy solutions. Full article

Microalgal biomass contributes to the valorization of urban and agro-industrial solid waste via hydrothermal co-liquefaction (co-HTL) for the production of biocrude, a sustainable substitute for petroleum. Tropical and populous countries like Brazil generate a lot of agro-industrial waste, such as sugarcane bagasse and malt bagasse, as well as sludge from sewage treatment plants. Such residues are potential sources of biocrude production via thermochemical conversion. To increase biocrude productivity, microalgal biomass has been successfully used in mixing the co-HTL process feed with different residues. In addition to biocrude, co-HTL generates an aqueous phase that can be used to produce H₂ and/or electricity via microbial energy cells. In this sense, this paper aims to present the potential for generating energy from solid waste commonly generated in emerging countries such as Brazil based on a simplified scheme of a conceptual biorefinery employing algal biomass co-HTL together with sugarcane bagasse, malt bagasse, and sludge. The biorefinery model could be integrated into an ethanol production plant, a brewery, or a sewage treatment plant, aiming at the production of biocrude and H₂ and/or electricity by bioelectrochemical systems, such as microbial electrolysis cells and microbial fuel cells. Full article

A microbial fuel cell (MFC) is a bio-electrochemical system that utilizes electroactive microorganisms to generate electricity. These microorganisms, which convert the energy stored in substrates such as wastewater into electricity, grow on the anode. To ensure biocompatibility, anodes are typically made from carbon-based materials. Therefore, a carbon-based material (by-product of coconut processing) was selected for testing in this study. The anode was prepared by bonding activated coconut carbon with carbon paint on a glass electrode. The aim of this study was to analyze the feasibility of using an electrode prepared in this manner as a surface layer on the anode of an MFC. The performance of an electrode coated only with carbon paint was also evaluated. These two electrodes were compared with a carbon felt electrode, which is commonly used as an anode material in MFCs. In this research, the MFC was fed with a by-product of yeast production, namely a molasses decoction from yeast processing. Measurements were conducted in a standard two-chamber glass MFC with a glass membrane separating the chambers. During the experiment, parameters such as start-up time, cell voltage during MFC start-up, output cell voltage, and power density curves were analyzed. The carbon paint-coated electrode with the activated coconut carbon additive demonstrated operating parameters similar to those of the carbon felt electrode. The results indicate that it is possible to produce electrodes (on a base of by-product of coconut processing) for MFCs using a painting method; however, to achieve a performance comparable to carbon felt, the addition of activated coconut carbon is necessary. This study demonstrates the feasibility of forming a biocompatible layer on various surfaces. Incorporating activated coconut carbon does not complicate the anode fabrication process, as fine ACC grains can be directly applied to the wet carbon paint layer. Additionally, the use of carbon paint as a conductive layer for the active anode in MFCs offers versatility in designing electrodes of various shapes, enabling them to be coated with a suitable active and conductive layer to promote biofilm formation. Moreover, the findings of this study confirm that waste-derived materials can be effectively utilized as electrode components in MFC anodes. The results validate the chosen research approach and emphasize the potential for further investigations in this field, contributing to the development of cost-efficient electrodes derived from by-products for MFC applications. Full article

The operating principle of a fuel cell is attracting increasing attention in the development of self-powered electrochemical sensors (SPESs). In this type of sensor, the chemical energy of the analyzed substance is converted into electrical energy in a galvanic cell through spontaneous electrochemical reactions, directly generating an analytical signal. Unlike conventional (amperometric, voltammetric, and impedimetric) sensors, no external energy in the form of an applied potential is required for the redox detection reactions to occur. SPESs therefore have several important advantages over conventional electrochemical sensors. They do not require a power supply and modulation system, which saves energy and costs. The devices also offer greater simplicity and are therefore more compatible for applications in wearable sensor devices as well as in vivo and in situ use. Due to the dual redox properties of hydrogen peroxide, it is possible to develop membraneless fuel cells and fuel-cell-based hydrogen peroxide SPESs, in which hydrogen peroxide in the analyzed sample is used as the only source of energy, as both an oxidant and a reductant (fuel). This also suppresses the dependence of the devices on the availability of oxygen. Electrode catalyst materials for different hydrogen peroxide reaction pathways at the cathode and the anode in a one-compartment cell are a key technology for the implementation and characteristics of hydrogen peroxide SPESs. This article provides an overview of the operating principle and designs of H₂O₂–H₂O₂ fuel cells and H₂O₂ fuel-cell-based SPESs, focusing on biomimetic and nanozyme catalysts, and highlights recent innovations and prospects of hydrogen-peroxide-based SPESs for (bio)electrochemical analysis. Full article

Microalgae microbial fuel cells (pMFCs) are distinguished by their ability to combine waste utilization with the simultaneous recovery of energy and valuable materials. The generation of high current density is linked to the efficient electron transfer to the anode via the anodic biofilm and the high photosynthetic activity of the microalgae cultivated in the cathode chamber. This review explores the impact of wastewater type on energy production and wastewater treatment. Additionally, it discusses the challenges related to microalgae growth in the cathode chamber, the necessity of aeration, and the sequestration of carbon dioxide from the anode chamber. The efficiency of microalgae in utilizing nutrients from various types of wastewater is also presented. In conclusion, the comparison between wastewater treatment and energy balance in pMFCs and conventional wastewater treatment plants is provided. On average, MFCs consume only 0.024 kW or 0.076 kWh/kg COD, which is approximately ten times less than the energy used by activated sludge bioprocesses. This demonstrates that MFCs offer highly efficient energy consumption compared to traditional wastewater treatment systems while simultaneously recovering energy through exoelectrogenic, bioelectrochemical processes. Full article

Bioelectrochemical systems (BESs) are devices capable of converting chemical energy into electrical energy using microorganisms as catalysts. These systems have been extensively studied at the laboratory level, but, due to multiple difficulties, their large-scale implementation has been explored only sparingly. This study presents the most recent technological advances for scaling up BESs. In the same way, the main technical and economic challenges that hinder the correct implementation of these systems at a large scale are mentioned. The study concludes with a review of successful case studies in scaling up BESs and discusses future directions and emerging trends. Full article

The rapid technological advancements and the shift towards clean energy have significantly increased the demand for metals, leading to an increasing metal pollution problem. This review explores recent advances in bioelectrochemical systems (BES) for metal recovery from waste, especially Acid Mine Drainage (AMD) and Electrical, Electronic Wastes (EEW) and waste from smelters, highlighting their potential as a sustainable and economically viable alternative to traditional methods. This study addresses the applications and limitations of current BES recovery techniques. BES, including microbial fuel cells (MFCs), microbial electrolytic cells (MECs), and Microbial Desalination Cells (MDCs), offer promising solutions by combining microbial processes with electrochemical reactions to recover valuable metals while reducing energy requirements. This review categorizes recent research into two main areas: pure BES applications and BES coupled with other technologies. Key findings include the efficiency of BES in recovering metals like copper, chromium, vanadium, iron, zinc, nickel, lead, silver, and gold and the potential for integrating BES with other systems to enhance performance. Despite significant progress in BES application for metal recovery, challenges such as high costs and slow kinetics remain, necessitating further research to optimize materials, configurations, and operational conditions. The work also includes an economic assessment and guidelines for BES development and upscale. This review underscores the critical role of BES in advancing sustainable metal recovery and mitigating the environmental impact of metal pollution. Full article

This review evaluates the feasibility of using microalgal culture for sustainable energy production, emphasizing microbial fuel cells (MFCs) and biophotovoltaics (BPVs). This study’s uniqueness is rooted in its thorough examination of recent developments (2014–present) in microalgal strain selection, bioreactor design, and electrode materials. Furthermore, this review combines microalga cultivation with wastewater treatment, highlighting its importance. Notably, it examines advanced methodologies, such as the use of genetic engineering to enhance microalgal traits, nanotechnology to optimize electrode efficacy, and artificial intelligence (AI) to optimize bioelectrochemical systems. In addition, this study identifies possible future research avenues by examining microalga–bacterium consortia and cascaded biobattery systems. Consequently, the incorporation of case studies illustrating microalga biobatteries’ practical applications in low-power devices and wastewater treatment underscores the technology’s promise. Similarly, this study examines significant problems with enhancing farming methods, reconciling cost and yield, and integrating renewable energy sources with the grid, offering vital insights for academics and policymakers. Ultimately, this review emphasizes the need for economical cultivation methods, waste stream utilization, and scalable bioreactor designs, thereby considerably advancing sustainable energy options. Full article