Search Results (11)

The human body’s ability to recover from bone injuries is remarkable; however, in specific conditions, interventions are required to restore function and prevent complications. To accelerate osteogenesis, several strategies have been explored, including grafts, biomaterials, and adjuvant therapies. The aim of this narrative review was to analyze the preclinical evidence regarding the combination of particulate biomaterials and fibrin derivatives for bone regeneration. Publications using hydroxyapatite, bovine bone, β-tricalcium phosphate, and bioglass in association with fibrin glue, heterologous fibrin sealants, or platelet-rich fibrin were examined to identify recurrent experimental patterns and biological outcomes. According to the studies, hydroxyapatite and bovine bone were the most frequently investigated scaffolds, whereas fibrin glue and heterologous fibrin sealants showed consistent adhesion and favorable host response profiles in animal models. β-tricalcium phosphate demonstrated faster remodeling but lower volumetric stability, and bioglass showed high bioactivity in isolated reports. Despite heterogeneity in particle size, fibrin formulations, defect models, and follow-up periods, most studies reported enhanced bone deposition, vascularization, and integration when particulate biomaterials were combined with fibrin-based matrices. Overall, the evidence suggests that these combinations promote more organized and biologically favorable bone healing under experimental conditions. Future translational and clinical research is required to standardize protocols and determine the therapeutic applicability of these strategies in human bone repair. Full article

Dural tear (DT) and cerebrospinal fluid (CSF) leakage, though uncommon complications, represent a potentially serious risk of anterior cervical spine surgery, particularly in patients with ossification of the posterior longitudinal ligament (OPLL). While the incidence in routine anterior cervical discectomy and fusion (ACDF) or corpectomy (ACCF) is typically below 0.5%, it rises sharply to 4–32% in OPLL cases. Furthermore, it exceeds 60% when dural ossification (DO) is present. Adhesion and ossification obliterate the normal epidural plane, creating a fragile osteofibrotic interface that is highly susceptible to tearing during decompression. This review synthesizes current evidence on the pathophysiology of DT and CSF leakage in anterior cervical spine surgery, provides a framework for risk stratification, and outlines evolving techniques for successful repair and management. Intraoperative management has shifted from direct resection toward dura-preserving floating decompression and biologically reinforced multilayer repair using fascia, collagen matrix, fibrin adhesives, and polyethylene glycol (PEG) hydrogel sealants. Postoperative care emphasizes controlled CSF pressure regulation, sterile wound management, and early ambulation. Most DTs achieve successful closure with timely recognition and standardized treatment. However, persistent leakage may require escalation to composite reconstruction, epidural blood patch, or vascularized flap reinforcement. Emerging technologies such as bioactive hydrogels, 3D-printed dural scaffolds, and artificial intelligence–assisted imaging offer potential future improvements, although clinical adoption remains limited. This review summarizes current evidence on the mechanisms, risk factors, diagnostic predictors, repair strategies, and postoperative management of DT and CSF leakage, with specific attention to OPLL-related DO. A more apparent distinction between established clinical practice and emerging investigational technologies is provided to guide evidence-based decision-making. Full article

This systematic review aimed to evaluate the effect of laser surface treatment on the bond strength of adhesive restorative materials to primary teeth. A comprehensive literature search was conducted in PubMed, Scopus, Embase, Web of Science and WorldCat up to July 2025 using the keywords primary teeth, deciduous teeth, milk teeth, laser, adhesion, bond strength. Twenty-six studies met the inclusion criteria, including 22 shear bond strength (SBS), three microtensile bond strength (µTBS) and one microshear bond strength (µSBS) investigations. Most studies evaluated erbium lasers (Er:YAG, Er,Cr:YSGG), while fewer assessed diode, Nd:YAG or KTP devices. In dentin, erbium lasers at low-to-moderate energy levels consistently produced smear-free, micro-retentive surfaces with open tubules and bond strengths comparable to bur-prepared controls. High-energy irradiation, however, frequently caused microcracks, tubule collapse and reduced adhesion. In enamel, phosphoric acid etching remained the most effective conditioning method, although combined laser–acid pretreatment often improved bonding of sealants and composites. Material-dependent effects were also evident: resin composites generally outperformed glass ionomers, hybrids and bioactive restorative materials. Phosphoric acid etching remains indispensable for enamel conditioning, while dentin benefits from carefully controlled erbium laser irradiation in combination with suitable adhesive systems. Full article

Background: This study evaluates the impact of fibrinogen enrichment on the structural, mechanical, and bioactive properties of fibrin scaffold derived from balanced protein-concentrate plasma (BPCP), an autologous platelet-rich plasma (PRP) formulation with elevated extraplatelet content. Methods: A novel high-fibrinogen BPCP (HF-BPCP) scaffold was produced by combining BPCP platelet lysate with a concentrated fibrinogen solution at a 1:1 ratio, yielding nearly four-fold physiological fibrinogen levels. Comparative analyses between HF-BPCP and standard BPCP included platelet and fibrinogen quantification, scanning electron microscopy (SEM), rheology, indentation, adhesion testing, coagulation kinetics, retraction assays, biodegradation profiling, and growth factor (GF) release kinetics. Results: HF-BPCP displayed significantly denser fibrin networks with thinner fibers, higher porosity, and markedly faster coagulation times compared to BPCP. Mechanically, HF-BPCP exhibited greater stiffness, higher energy dissipation, and more stable adhesion, while almost eliminating scaffold retraction at 24 h. Despite improved early handling and structural integrity, HF-BPCP degraded more rapidly in vitro under tissue plasminogen activator exposure. GF release analysis showed reduced early peaks of platelet-derived factors (TGF-β1, PDGF-AB, VEGF) but sustained release thereafter, while extraplatelet factors (IGF-1, HGF) exhibited similar profiles between scaffolds. Conclusions: These results indicate that fibrinogen enrichment synergizes with the elevated extraplatelet protein profile of BPCP to enhance scaffold mechanical stability, handling properties, and controlled GF delivery. HF-BPCP combines the adhesive, structural, and bioactive features of fibrin sealants with the regenerative potential of PRP, offering a fully autologous alternative for clinical applications requiring rapid coagulation, high mechanical support, and sustained GF availability. Further preclinical and clinical studies are needed to evaluate therapeutic efficacy in the regenerative medicine field. Full article

The purpose of this study was to evaluate a resin based pit and fissure sealant containing 45S5 bioactive glass (BAG) by examining its ion release, pH variation, and apatite-forming properties. To prepare the experimental materials, 45S5 BAG, used as a filler, was incorporated into the light curable resin matrix at concentrations of 0 (control), 12.5, 37.5, and 50.0 wt.%. Ion release, pH variation, and apatite formation (Raman spectrometer and scanning electron microscopy-energy-dispersive X-ray spectrometry measurements) were performed. While no ions were released from the control group, the experimental groups containing 45S5 BAG showed an increased release of Ca and P ions with increasing amounts of 45S5 BAG (p < 0.05). The pH of the experimental group remained high and was significantly different from the control group (p < 0.05). Unlike the control group, it was confirmed that the apatite peak was formed in the 50.0 wt.% BAG group for 90 days, and the apatite layer consisting of Ca and P was deposited on the surface. Thus, a resin based pit and fissure sealant containing 45S5 BAG is a promising material for preventing secondary caries by releasing ions and forming apatite. Full article

The aim of this study was to assess the chemical/mechanical properties of ion-releasing dental sealants containing strontium-bioactive glass nanoparticles (Sr-BGNPs) and monocalcium phosphate monohydrate (MCPM). Two experimental sealants, TS1 (10 wt% Sr-BGNPs and 2 wt% MCPM) and TS2 (5 wt% Sr-BGNPs and 4 wt% MCPM), were prepared. Commercial controls were ClinproXT (CP) and BeautiSealant (BT). The monomer conversion (DC) was tested using ATR–FTIR (n = 5). The biaxial flexural strength (BFS) and modulus (BFM) were determined (n = 5) following 24 h and 7 days of immersion in water. The Vickers surface microhardness (SH) after 1 day in acetic acid (conc) versus water was tested (n = 5). The bulk and surface calcium phosphate precipitation in simulated body fluid was examined under SEM-EDX. The ion release at 4 weeks was analyzed using ICP-MS (n = 5). The DC after 40 s of light exposure of TS1 (43%) and TS2 (46%) was significantly lower than that of CP (58%) and BT (61%) (p < 0.05). The average BFS of TS1 (103 MPa), TS2 (123 MPa), and BT (94 MPa) were lower than that of CP (173 MPa). The average BFM and SH of TS1 (2.2 GPa, 19 VHN) and TS2 (2.0 GPa, 16 VHN) were higher than that of CP (1.6 GPa, 11 VHN) and BT (1.3 GPa, 12 VHN). TS1 showed higher Ca, P, and Sr release than TS2. Bulk calcium phosphate precipitation was detected on TS1 and TS2 suggesting some ion exchange. In conclusion, the DC of experimental sealants was lower than that of commercial materials, but their mechanical properties were within the acceptable ranges. The released ions may support remineralizing actions. Full article

The incorporation of remineralizing additives into sealants has been considered as a feasible way to prevent caries by potential remineralization through ions release. Thus, this systematic review aimed to identify the remineralizing additives in resin-based sealants (RBS) and assess their performance. Search strategies were built to search four databases (PubMed, MEDLINE, Web of Science and Scopus). The last search was conducted in June 2020. The screening, data extraction and quality assessment were completed by two independent reviewers. From the 8052 screened studies, 275 full-text articles were assessed for eligibility. A total of 39 laboratory studies matched the inclusion criteria. The methodologies used to assess the remineralizing effect included microhardness tests, micro-computed tomography, polarized-light microscopy, ions analysis and pH measurements. Calcium phosphate (CaP), fluoride (F), boron nitride nanotubes (BNN), calcium silicate (CS) and hydroxyapatite (HAP) were incorporated into resin-based sealants in order to improve their remineralizing abilities. Out of the 39 studies, 32 studies focused on F as a remineralizing agent. Most of the studies confirmed the effectiveness of F and CaP on enamel remineralization. On the other hand, BNN and CS showed a small or insignificant effect on remineralization. However, most of the included studies focused on the short-term effects of these additives, as the peak of the ions release and concentration of these additives was seen during the first 24 h. Due to the lack of a standardized in vitro study protocol, a meta-analysis was not conducted. In conclusion, studies have confirmed the effectiveness of the incorporation of remineralizing agents into RBSs. However, the careful interpretation of these results is recommended due to the variations in the studies’ settings and assessments. Full article

Background: Sealing occlusal pits and fissures is an effective preventive measure against dental caries. Pit and fissure sealants (PFS) should be strongly bonded to the teeth to prevent partial or complete loss of the sealant, which may limit its preventive effect. Objective: The objective of the study was to compare the microtensile bond strength (μTBS) of bioactive resin-based sealants (Bio-RBS) and resin-based sealants (RBS), with and without the use of a bonding agent, to the enamel of primary and permanent teeth. Methods: One hundred and twenty caries-free primary molar specimens and 120 permanent molar specimens were divided to eight groups (30 specimens per group), both primary and permanent teeth were sealed with a Bio-RBS BioCoat^TM (Premier^®, Plymouth Meeting, PA, USA) or with a RBS Clinpro^TM (3M ESPE, Saint Paul, MN, USA), with or without the use of a bonding agent (Prime & Bond NT; Dentsply, Inc., Charlotte, NC, USA). Half the specimens were aged with 5000 thermal cycles, and all specimens were tested for the μTBS and failure mode. Results: The mean μTBS of aged Bio-RBS was higher in permanent teeth than primary teeth, and the aging process reduced the μTBS of RBS more than that of Bio-RBS. Moreover, the addition of a bonding agent improved the μTBS of aged RBS in permanent teeth. Conclusion: We concluded that Bio-RBS exhibit superior μTBS than RBS when applied to permanent teeth. Full article

Objective: To assess the remineralizing abilities and compare the flexural strength and elastic modulus of different bioactive pit and fissure sealants. Materials and Methods: Human enamel samples were randomly and blindly sealed with one of the following bioactive materials: BioCoat (Bc), ACTIVA KIDS (Av) and BeautiSealant (Bu). Seal-it (Si) was used as a non-bioactive sealant beside a control blank (B) group with no sealant. The sealed samples were subjected to a pH-cycling model (7 days of demineralization–remineralization cycles). The enamel surface hardness change (SHC), scanning electron microscopy-energy dispersive X-ray spectroscopy (SEM-EDX) and polarized light microscopy were used to assess the remineralizing abilities of the studied sealants. Flexural strength and elastic modulus were also assessed following the ISO 4049 protocols. One-way analysis of variance (ANOVA) was used to analyze the results. Results: Bc sealant showed the highest FS and EM (p < 0.05). The contact with Bc and Bu sealants showed significantly lower %SHL (p < 0.05) in comparison to the other. These findings were supported by the results of SEM-EDX and polarized imaging by showing higher percentages of calcium and phosphate ions with the former sealants and thinner demineralized enamel bands. Conclusion: In this study, Bc showed the highest flexural strength. Bc and Bu sealants outperformed the other studied sealants in terms of their remineralization abilities. Full article

Since pits and fissures are the areas most commonly affected by caries due to their structural irregularity, bioactive resin-based sealant (RBS) may contribute to the prevention of secondary caries. This study aims to investigate the mechanical, physical, ion-release, enamel remineralisation, and antibacterial capabilities of the novel RBS with bioactive glass (BAG) and 2-methacryloyloxyethyl phosphorylcholine (MPC). For the synthesis, 12.5 wt% BAG and 3 wt% MPC were incorporated into RBS. The contact angle, flexural strength, water sorption, solubility, and viscosity were investigated. The release of multiple ions relating to enamel remineralisation was investigated. Further, the attachments of bovine serum albumin, brain heart infusion broth, and Streptococcus mutans on RBS were studied. Finally, the thickness and biomass of a human saliva-derived microsm biofilm model were analysed before aging, with static immersion aging and with thermocycling aging. In comparison to commercial RBS, BAG+MPC increased the wettability, water sorption, solubility, viscosity, and release of multiple ions, while the flexural strength did not significantly differ. Furthermore, RBS with MPC and BAG+MPC significantly reduced protein and bacteria adhesion and suppressed multi-species biofilm attachment regardless of the existence of aging and its type. The novel RBS has great potential to facilitate enamel remineralisation and suppress biofilm adhesion, which could prevent secondary dental caries. Full article

Cariogenic oral biofilms are strongly linked to dental caries around dental sealants. Quaternary ammonium monomers copolymerized with dental resin systems have been increasingly explored for modulation of biofilm growth. Here, we investigated the effect of dimethylaminohexadecyl methacrylate (DMAHDM) on the cariogenic pathogenicity of Streptococcus mutans (S. mutans) biofilms. DMAHDM at 5 mass% was incorporated into a parental formulation containing 20 mass% nanoparticles of amorphous calcium phosphate (NACP). S. mutans biofilms were grown on the formulations, and biofilm inhibition and virulence properties were assessed. The tolerances to acid stress and hydrogen peroxide stress were also evaluated. Our findings suggest that incorporating 5% DMAHDM into 20% NACP-containing sealants (1) imparts a detrimental biological effect on S. mutans by reducing colony-forming unit counts, metabolic activity and exopolysaccharide synthesis; and (2) reduces overall acid production and tolerance to oxygen stress, two major virulence factors of this microorganism. These results provide a perspective on the value of integrating bioactive restorative materials with traditional caries management approaches in clinical practice. Contact-killing strategies via dental materials aiming to prevent or at least reduce high numbers of cariogenic bacteria may be a promising approach to decrease caries in patients at high risk. Full article