Search Results (370)

Biopolymers and bio-based plastics, such as polylactic acid (PLA) and polybutylene succinate (PBS), are recognized as environmentally friendly materials and are widely used, especially in the packaging industry. The purpose of this study was to assess the degradation of PLA- and PBS-based formulations in the forms of granules and films under controlled composting conditions at a laboratory scale. Biodegradation tests of bio-based materials were conducted under controlled aerobic conditions, following the standard EVS-EN ISO 14855-1:2012. Scanning electron microscopy (SEM) was performed using a high-resolution Zeiss Ultra 55 scanning electron microscope to analyze the samples. After the six-month laboratory-scale composting experiment, it was observed that the PLA-based materials degraded by 47.46–98.34%, while the PBS-based materials exhibited a final degradation degree of 34.15–80.36%. Additionally, the PLA-based compounds displayed a variable total organic carbon (TOC) content ranging from 38% to 56%. In contrast, the PBS-based compounds exhibited a more consistent TOC content, with a narrow range from 53% to 54%. These findings demonstrate that bioplastics can contribute to reducing plastic waste through controlled composting, but their degradation efficiency depends on the material composition and environmental conditions. Future efforts should optimize bioplastic formulations and composting systems while developing supportive policies for wider adoption. Full article

The production of bionanocomposite films based on carboxymethyl derivatives of starch and cellulose with sodium montmorillonite (MMT-Na) as a filler was described. The developed films with high absorbency can be used in the preparation of adhesive dressings for wounds oozing as a result of abrasions or tattoos. Carboxymethyl cellulose (CMC), carboxymethyl starch (CMS), and potato starch were used as the raw materials for film manufacturing. Citric acid was used as a crosslinking agent and glycerol as a plasticizer. The following parameters were evaluated for the obtained films: solubility in water, swelling behavior, moisture absorption, and mechanical durability (tensile strength, elongation at break, and Young’s modulus). This study revealed that filler concentration has a significant influence on the stability, durability, and moisture absorption parameters of films. The best nanocomposite with a high absorption capacity was a two-component film CMS/CMC containing 5 pph of sodium montmorillonite and can be used as a base material for wound dressing, among other applications. Full article

Hydrogels have emerged as multifunctional biomaterials in cardiac surgery, offering promising solutions for myocardial regeneration, adhesion prevention, valve engineering, and localized drug and gene delivery. Their high water content, biocompatibility, and mechanical tunability enable close emulation of the cardiac extracellular matrix, supporting cellular viability and integration under dynamic physiological conditions. In myocardial repair, injectable and patch-forming hydrogels have been shown to be effective in reducing infarct size, promoting angiogenesis, and preserving contractile function. Hydrogel coatings and films have been designed as adhesion barriers to minimize pericardial adhesions after cardiotomy and improve reoperative safety. In heart valve and patch engineering, hydrogels contribute to scaffold design by providing bio-instructive, mechanically resilient, and printable matrices that are compatible with 3D fabrication. Furthermore, hydrogels serve as localized delivery platforms for small molecules, proteins, and nucleic acids, enabling sustained or stimuli-responsive release while minimizing systemic toxicity. Despite these advances, challenges such as mechanical durability, immune compatibility, and translational scalability persist. Ongoing innovations in smart polymer chemistry, hybrid composite design, and patient-specific manufacturing are addressing these limitations. This review aims to provide an integrated perspective on the application of hydrogels in cardiac surgery. The relevant literature was identified through a narrative search of PubMed, Scopus, Web of Science, Embase, and Google Scholar. Taken together, hydrogels offer a uniquely versatile and clinically translatable platform for addressing the multifaceted challenges of cardiac surgery. Hydrogels are poised to redefine clinical strategies in cardiac surgery by enabling tailored, bioresponsive, and functionally integrated therapies. Full article

In this paper, a series of polyaniline (PANI)/Ti₃C₂ MXene composites (PMCs) with a biomimetic structure were prepared and employed as an anticorrosion coating application. First, the PANI was synthesized by oxidative polymerization with ammonium persulfate as the oxidant. Then, 2D Ti₃C₂ MXene nanosheets were prepared by treating the Ti₃AlC₂ using the optimized minimally intensive layer delamination (MILD) method, followed by characterization via XRD and SEM. Subsequently, the PMC was prepared by the oxidative polymerization of aniline monomers in the presence of Ti₃C₂ MXene nanosheets, followed by characterization via FTIR, XRD, SEM, TEM, CV, and UV–Visible. Eventually, the PMC coatings with the artificial biomimetic surface structure of a macaw feather were prepared by the nano-casting technique. The corrosion resistance of the PMC coatings, evaluated via Tafel polarization and Nyquist impedance measurements, shows that increasing the MXene loading up to 5 wt % shifts the corrosion potential (E_corr) on steel from −588 mV to −356 mV vs. SCE, reduces the corrosion current density (I_corr) from 1.09 µA/cm² to 0.035 µA/cm², and raises the impedance modulus at 0.01 Hz from 67 kΩ to 3794 kΩ. When structured with the hierarchical feather topography, the PMC coating (Bio-PA-MX-5) further advances the E_corr to +103.6 mV, lowers the I_corr to 7.22 × 10⁻⁴ µA/cm², and boosts the impedance to 96,875 kΩ. Compared to neat coatings without biomimetic structuring, those with engineered biomimetic surfaces showed significantly improved corrosion protection performance. These enhancements arise from three synergistic mechanisms: (i) polyaniline’s redox catalysis accelerates the formation of a dense passive oxide layer; (ii) MXene nanosheets create a tortuous gas barrier that cuts the oxygen permeability from 11.3 Barrer to 0.9 Barrer; and (iii) the biomimetic surface traps air pockets, raising the water contact angle from 87° to 135°. This integrated approach delivers one of the highest combined corrosion potentials and impedance values reported for thin-film coatings, pointing to a general strategy for durable steel protection. Full article

This study investigates the development of corn starch-based biocomposites reinforced with pistachio shell powder, focusing on improving their mechanical and thermal performance. Composite films were prepared by solution casting with pistachio shell contents ranging from 2 wt% to 8 wt% by weight. The materials were characterized using Fourier-transform infrared spectroscopy (FTIR), thermogravimetric analysis (TGA), X-ray diffraction (XRD), and tensile testing. The incorporation of pistachio shell particles led to a progressive improvement in tensile strength and elastic modulus, with the highest values observed in the formulation with 8% reinforcement (SP08). The TGA results indicated a shift in degradation temperatures for the sample with the highest percentage, reflecting a higher thermal stability that is attributed to the interactions between the starch, plasticizer, and cellulosic components of the pistachio shell. The FITR spectra shows very similar structures between starch and pistachio. An XRD analysis shows the alpha-type structure for starch and the cellulose type 1 structure for pistachio. Overall, the results suggest that pistachio shell powder can serve as an effective natural reinforcement, improving the functional properties of starch matrices and promoting the development of environmentally friendly materials derived from agro-industrial waste. Full article

Bio-nanocomposite films were prepared using chitosan, gelatin, and varying concentrations (0, 0.5, 1.0, 2.0, and 5.0 wt%) of titanium dioxide (TiO₂) nanoparticles in acetic acid via a casting method. The incorporation of TiO₂ nanoparticles into the bio-chitosan matrix enhanced ultraviolet (UV) absorption and improved the films’ physical, mechanical, and electrical properties. Additionally, the TiO₂-loaded films exhibited antimicrobial activity, contributing to the extended preservation of packaged products by inhibiting microbial growth. Notably, the bio-nanocomposite films containing 1.0 wt% TiO₂ exhibited an electroactive response, bending under relatively low electric field strength (250 V/mm), whereas the control film without TiO₂ required higher field strength (550 V/mm) to achieve bending. This indicates potential applications in electroactive actuators requiring precise movement control. Among the tested concentrations, films containing 0.5 wt% and 1.0 wt% TiO₂ (Formulas 7 and 8) demonstrated optimal performance. These films presented a visually appealing appearance with no tear marks, low bulk density (0.91 ± 0.04 and 0.85 ± 0.18 g/cm³), a satisfactory electromechanical response at 250 V/m (17.85 ± 2.58 and 61.48 ± 6.97), low shrinkage percentages (59.95 ± 3.59 and 54.17 ± 9.28), high dielectric constant (1.80 ± 0.07 and 8.10 ± 0.73), and superior UV absorption compared with pure bio-chitosan films, without and with gelatin (Formulas 1 and 6). Full article

Batteries are used as energy storage devices in various equipment. Today, research is focused on solid-state batteries (SSBs), replacing the liquid electrolyte with a solid separator. The solid separators provide electrolyte stability, no leakage, and provide mechanical strength to the battery. Separators are mostly manufactured by either traditional processes or 3D printing technologies. These processes involve making a slurry of plastic, active and conductive material and usually adding a plasticizer when making thin films or filaments for 3D printing. This study investigates the additive manufacturing of solid-state electrolytes (SSEs) by employing fused deposition modeling (FDM) with recyclable, bio-derived polylactic acid (PLA) filaments. Precise control of macro-porosity is achieved by systematically varying key process parameters, including raster orientation, infill percentage, and interlayer adhesion conditions, thereby enabling the formation of tunable, interconnected pore networks within the polymer matrix. Following 3D printing, these engineered porous frameworks are infiltrated with lithium hexafluorophosphate (LiPF₆), which functions as the active ionic conductor. A tailored thermal sintering protocol is then applied to promote solid-phase fusion of the embedded salt throughout the macro-porous PLA scaffold, resulting in a mechanically robust and ionically conductive composite separator. The electrochemical ionic conductivity and structural integrity of the sintered SSEs are characterized through electrochemical impedance spectroscopy (EIS) and standardized mechanical testing to assess their suitability for integration into advanced solid-state battery architectures. The solid-state separator achieved an average ionic conductivity of 2.529 × 10⁻⁵ S·cm⁻¹. The integrated FDM-sintering process enhances ion exchange at the electrode–electrolyte interface, minimizes material waste, and supports cost-efficient, fully recyclable component fabrication. Full article

As the global plastic pollution problem intensifies and the environmental hazards of traditional petroleum-based plastics become increasingly significant, the development of sustainable alternative materials has become an urgent need. This paper systematically reviews the research progress, application status and future trends of new generation bioplastics in the field of food packaging. Bioplastics are categorized into three main groups according to their sources and degradability: biobased biodegradable materials (e.g., polylactic acid PLA, polyhydroxy fatty acid ester PHA, chitosan, and cellulose-based materials); biobased non-biodegradable materials (e.g., Bio-PE, Bio-PET); and non-biobased biodegradable materials (e.g., PBAT, PCL, PBS). Different processing technologies, such as thermoforming, injection molding, extrusion molding and coating technologies, can optimize the mechanical properties, barrier properties and freshness retention of bioplastics and promote their application in scenarios such as food containers, films and smart packaging. Although bioplastics still face challenges in terms of cost, degradation conditions and industrial support, promising future directions are found in the development of the large-scale utilization of non-food raw materials (e.g., agricultural waste, algae), nano-composite technology to enhance the performance, and the development of intelligent packaging functions. Through technological innovation and industry chain integration, bioplastics are expected to transform from an environmentally friendly alternative to a mainstream packaging material, helping to realize the goal of global carbon neutrality. Full article

Plastic film mulching is widely used in protected agriculture. However, the residues of various types of plastic films, as a consequence, severely affect soil quality. The most widely promoted alternative strategy is the use of biodegradable plastic films. Nevertheless, the research on the effects of different types of plastic films on soil properties remains insufficient. This study explored the impacts of different plastic film mulching on the physicochemical properties and microbial communities of soils for pepper cultivation, with three treatments: traditional polyethylene film (PE-Ctr), PBAT biodegradable film (PBAT bio), and reinforced polyethylene film (RPE). The results showed that the soil pH value was the highest in PE-Ctr treatment, and the soil organic matter content was higher in the biodegradable film treatment, while the electrical conductivity (EC), nitrate, and some cations (Ca²⁺, Mg²⁺) were higher in the RPE treatment. The contents of available trace element Zn, Fe, and Mn increased in the PBAT bio treatment. The bacterial richness and evenness indices were higher in PBAT bio treatment than those of other treatments. The fungal community had a relatively high richness, but a lower evenness, compared to the PE-Ctr and PBAT bio treatments. The use of different plastic films significantly affected the composition of soil bacteria, while differences in the composition of soil fungi were only observed between the PBAT bio and RPE treatments. Proteobacteria, Acidobacteriota, and Actinobacteriota were the most dominant bacterial phyla, and Ascomycota and Mortierellomycota were the dominant fungal phylum across all treatments. FAPROTAX functional prediction showed that the abundances of multiple functions of soil bacteria were higher in the RPE treatment, and the chemoheterotrophy function was higher in the PE treatment. FUNGuild analysis indicated that the trophic types and ecological function groups of soil fungi were more abundant in the PBAT bio treatment. Full article

Grape stalk (GS) from winemaking is a waste rich in antioxidant compounds that can be valorized to obtain active food packaging materials. Biocomposite films of poly (butylene succinate) (PBS) and poly(3-hydroxybutyrate)-co-hydroxyvalerate (PHBV) with 10% of GS particles, previously submitted or not to subcritical water extraction at 170 °C and 180 °C, were obtained by melt blending and characterized. The fibres were better integrated in the PHBV matrix than in PBS, while other molecular compounds from the fillers were released to the polymer matrix, allowing for their antioxidant action. Fillers promoted the stiffness of PBS films (11–44%), reducing their resistance to break and extensibility by 25%, without significant changes in polymer crystallinity or thermal stability. However, this reduced the crystallinity (13%) and thermal stability of PHBV films, decreasing their rigidity (55%). All fibres promoted the oxygen barrier capacity in composites (by about 20–35% for PBS and PHBV, respectively) while also providing them with UV light blocking effects. This barrier effect enhanced the ability of the films to preserve sunflower oil against oxidation, while in PHBV composites, the migration of antioxidant compounds was also detected. No remarkable differences in the effects of the different GS fillers on the properties of composites were detected. Full article

High-performance flexible sensors capable of direct integration with biological tissues are essential for personalized health monitoring, assistive rehabilitation, and human–machine interaction. However, conventional devices face significant challenges in achieving conformal integration with biological surfaces, along with sufficient biomechanical compatibility and biocompatibility. This research presents an in situ 3D biomanufacturing strategy utilizing Direct Ink Writing (DIW) technology to fabricate functional bioelectronic interfaces directly onto human skin, based on a novel annealing PEDOT:PSS/PVA composite bio-ink. Central to this strategy is the utilization of a novel annealing PEDOT:PSS/PVA composite material, subjected to specialized processing involving freeze-drying and subsequent thermal annealing, which is then formulated into a DIW ink exhibiting excellent printability. Owing to the enhanced network structure resulting from this unique fabrication process, films derived from this composite material exhibit favorable electrical conductivity (ca. 6 S/m in the dry state and 2 S/m when swollen) and excellent mechanical stretchability (maximum strain reaching 170%). The material also demonstrates good adhesion to biological interfaces and high-fidelity printability. Devices fabricated using this material achieved good conformal integration onto a finger joint and demonstrated strain-sensitive, repeatable responses during joint flexion and extension, capable of effectively transducing local strain into real-time electrical resistance signals. This study validates the feasibility of using the DIW biomanufacturing technique with this novel material for the direct on-body fabrication of functional sensors. It offers new material and manufacturing paradigms for developing highly customized and seamlessly integrated bioelectronic devices. Full article

This study investigates the valorization of agri-food residues by repurposing industrial rosehip oil waste for sustainable food packaging development. Market demands for environmentally friendly alternatives to conventional packaging materials prompted the development of laminated multilayer materials for trays through thermo-compression, using modified cassava starch with citric acid as a compatibilizer. Physicochemical characterization revealed appropriate surface roughness (Rz of 31–64 μm) and controlled water absorption capacities of the composite materials (contact angle of 85–95°), properties critical for food quality preservation and safety. The incorporation of polylactic acid (PLA) films in the laminates significantly enhanced the mechanical performance, increasing the stress resistance by 5 to 10 times, and improved moisture resistance, showing a 78–82% reduction in the materials’ water absorption capacity and an almost 50% decrease in water content and solubility, depending on the processing method. Results indicated that these biocomposite laminates represent a viable alternative to conventional polystyrene foam trays for food packaging. Two distinct multilayer manufacturing processes were comparatively evaluated to optimize production efficiency by reducing the energy consumption and processing time. This research contributes to circular economy principles by transforming agricultural waste into value-added laminated materials with commercial potential. Full article

Development of bio-based active packaging systems for lipid stabilization presents critical importance in preserving lipid integrity and ensuring food safety. Zein/citric acid (Z/CA) composite films containing grape seed ethanol extract (GSEE) (0–8% w/w) were prepared by the solvent casting method. The structural, functional, and environmental properties of the films, including physical and chemical properties, mechanical properties, antioxidant capacity, antibacterial activity, oxidation inhibition effect, and biodegradability, were comprehensively characterized and evaluated. Progressive GSEE enrichment significantly enhanced film thickness (p < 0.05), hydrophobicity, and total phenolic content, while increasing water vapor permeability by 61.29%. Antioxidant capacity demonstrated radical scavenging enhancements of 83.75% (DPPH) and 89.33% (ABTS) at maximal GSEE loading compared to control films. Mechanical parameters exhibited inverse proportionality to GSEE concentration, with tensile strength and elongation at break decreasing by 28.13% and 59.43%, respectively. SEM microstructural analysis revealed concentration-dependent increases in surface asperity and cross-sectional phase heterogeneity. Antimicrobial assays demonstrated selective bacteriostatic effects against Gram-negative pathogens. Notably, the composite film containing 6 wt% GSEE had a remarkable restraining effect on the oxidation of lard. The soil degradation experiment has confirmed that the Z/CA/GSEE composite film can achieve obvious degradation within 28 days. The above results indicate that the Z/CA/GSEE composite material emerges as a promising candidate for sustainable active food packaging applications. Full article

Money Art is a growing contemporary practice where artists transform banknotes into unique visual works. While conceptually powerful, these artworks present significant conservation challenges due to their fragile substrates and complex material compositions. This study investigates the degradation behaviour of UniPosca acrylic markers applied on zero-euro banknotes, drawing on the techniques of artist RichardHTT, and explores bio-based protective strategies suitable for their preservation. Laboratory samples were prepared to replicate the original artwork and subjected to accelerated ageing. A multi-analytical approach was employed, including multispectral imaging, Fourier trasform infrared (FTIR) and Raman spectroscopy, and scanning electron microscopy (SEM-EDS) colorimetric analysis. Thickness and adhesion properties were assessed with contact micrometry and peel tests, while wettability was evaluated through static contact angle measurements. Four biopolymer coatings, chitosan and chitosan–nanocellulose films with varying CNC concentrations, were evaluated for their transparency, mechanical stability, and compatibility with the substrate. Results showed that painted areas, especially those with blue and black pigments, experienced marked degradation, while, after coating application, samples demonstrated improved chromatic stability, hydrophobicity, and adhesion. Importantly, all coatings were fully removable via enzymatic cleaning with α-amylase, confirming their reversibility. This research highlights the potential of chitosan-based biocomposites as conservation materials for non-traditional artworks and contributes to developing tailored, reversible strategies for contemporary art preservation. Full article

To address the problem of environmental pollution caused by the extensive use of low-density polyethylene (LDPE) mulch film, this study developed a novel sprayable mulch using natural fibers and biodegradable polymers. Urea–formaldehyde resin (UF), strengthened with polyvinyl alcohol (PVA), was used as a modifier to induce beneficial physicochemical structural changes in PVA-modified urea–formaldehyde (PUF) resins. Characterization of these resins was conducted using Fourier transformation infrared spectroscopy (FT-IR), thermogravimetric analysis (TGA), and scanning electron microscopy (SEM). Preparation of the biodegradable mulch was conducted using Xuan paper waste residue (XP) as an enhancer, with PUF as the auxiliary agent. The resulting film (PUF-XP) was examined for differences in thickness, morphological characterization, and rate of weight loss, and the effects of different covering films on cucumber growth, root development, soil temperature, and weed control were evaluated. Characterization reveals that when the PVA content was 4% (W4UF), the film had the lowest free formaldehyde content (0.26%) and highest elongation at break (5.70%). In addition, W4UF could easily undergo thermal degradation at 278.4 °C and possessed a close-knit, three-dimensional structural network. W4UF was then mixed with paper powder and water in various proportions to produce three mulch films (BioT1, BioT2, and BioT3) that demonstrated excellent water retention and heat preservation and inhibited weed growth by 68.8–96.8%. Compared to no mulching (NM), BioT1 increased both the specific root length and root density, as well as improved the plant height, stem diameter, and total biomass of the cucumbers by 43.5%, 34.1%, and 33.9%, respectively. Therefore, a mass ratio of paper powder, water, and W4UF of 1:30:2 produced a biodegradable mulch film that could be used as an alternative to LDPE, mitigating the environmental pollution rendered by synthetic plastic mulch films and offering the potential for a sustainable agricultural application. Full article