Search Results (24)

This study presents an analytical framework for evaluating the admissibility of biaxial inclination of rectangular sinking wells. The inclination of the well is interpreted as an eccentric transfer of the vertical load to the concrete plug, which produces a two-dimensional linear stress field beneath the base. Closed-form expressions are derived for the stresses at the four corners of the rectangular base as functions of the eccentricity components associated with the two orthogonal tilt directions. Based on these expressions, the admissibility of inclination is represented by a tilt envelope in the space of the two tilt angles, defining the combinations of tilt components that satisfy the adopted serviceability criterion. The analytical formulation also allows for comparison between the stress-based admissibility limit, the geometric condition corresponding to loss of compressive contact beneath the base, and a simplified indicator of lateral wall-pressure asymmetry acting on the shaft. Parametric analyses show that biaxial inclination leads to stress concentration at the corners of the base and that even relatively small tilt components may combine to produce significant stress amplification. The geometry of the well strongly influences the shape of the admissible tilt envelope, with elongated rectangular wells exhibiting directional anisotropy of the allowable inclination. The proposed analytical approach provides a transparent tool for evaluating inclined wells using basic geometric parameters in engineering practice. Full article

Background: The wear resistance of modern commercial glass-ceramic materials used in dental prostheses was investigated under cyclic contact conditions that included a rotational component. This loading mode has been largely overlooked in conventional in vitro wear testing, yet may be clinically relevant in patients with parafunctional conditions such as bruxism. Methods: Rotational loading was applied using an all-electric testing machine equipped with a biaxial actuator. Loading cycles combined a normal load (50 N) and a rotation (30°), at a frequency of 1 Hz. Microstructure and damage were characterized using advanced microscopy. Results: Rotational loading induced substantial damage across this class of materials, including the formation of glassy tribolayers with limited protective capability under the low-humidity conditions examined. Significant microstructure-dependent variations in wear volume were observed, with specific wear rates indicating severe wear (SWR above 10⁻⁶ mm³/N·m threshold) in three of the five materials tested. Lithium disilicate glass-ceramics, characterized by a high fraction of elongated reinforcement crystals, exhibited the greatest resistance to damage, whereas leucite-based glass-ceramics showed the lowest. The dominant wear mechanisms were plastic-deformation-induced grooving and fracture-driven chipping. The findings are interpreted within established wear models for brittle materials (Archard and fracture-based) and supported by numerical simulations of stress fields across multiple length scales. Implications: The results provide mechanistic insight into rotational wear damage in glass-ceramic systems, a material class particularly susceptible to such loading, and inform strategies for material selection and microstructural design aimed at improving prosthetic durability. Full article

Biodegradable polymers offer a promising solution to the growing issue of global microplastic pollution. To effectively replace conventional plastics, it is essential to develop strategies for tuning the properties of biodegradable polymers without relying on additives. Biaxial stretching promotes anisotropic crystallization in polymer domains, thereby altering the mechanical performance of polymer blends. In this study, we employed a design of experiment (DoE) approach to investigate the effects of biaxial stretching at three drawing temperatures (T_ds) and draw ratios (λs) on a biodegradable blend of poly(lactic acid) (PLA) and poly(butylene adipate-co-terephthalate) (PBAT), aiming to optimize both the strength and ductility. The DoE analysis revealed that the composition, the λ, the interaction between the λ and composition, and the interaction between the T_d and composition significantly affect the elongation at break (ε_Break). For the stress at break (σ_Break), the most influential factors were the interaction between the λ and PLA concentration; a three-way interaction among the λ, PLA, and T_d; the T_d; the λ; and finally the PLA concentration alone. The optimal ε_Break and σ_Break were achieved at a λ = 5 × 5 and T_d = 110 °C, with a composition of 10% PLA and 90% PBAT. The stretched samples exhibited higher crystallinity compared to the pressed samples across all compositions. This work demonstrates that in addition to the composition, the processing parameters, such as the λ and T_d, critically influence the mechanical properties, enabling performance enhancements without the need for compatibilizers or toxic additives. Full article

The accuracy of numerical predictions in sheet metal processes involving multiaxial stress–strain states (e.g., blanking, riveting, and incremental forming) heavily depends on the characterisation of plastic anisotropy under multiaxial loading conditions. A fully calibrated 3D plastic anisotropy model is essential for this purpose. While in-plane material behaviour can be conventionally characterised through uniaxial and equi-biaxial tensile tests, calibrating out-of-plane material behaviour remains a significant challenge. This behaviour, governed by out-of-plane shear stress and associated material parameters, is typically described by out-of-plane shear yielding. These parameters are notoriously difficult to determine, leading researchers to frequently assume isotropic behaviour or identical shear parameters for in-plane and out-of-plane responses. Although advanced calibrations may utilise crystal plasticity modelling, there remains a critical need for macro-mechanical characterisation methods. This paper presents an out-of-plane shear testing and material characterisation procedure based on full-field strain measurements using digital image correlation (DIC). Strains within the shear zone are measured via DIC and employed in the Finite Element Model Updating (FEMU) to identify out-of-plane shear parameters of a 2.42 mm thick, cold-rolled AW5754-H22 aluminium alloy sheet, using the Yld2004-18p yield criterion. Given that the characteristic strain response at this scale may be influenced by local crystal structure behaviour on the surface, this paper evaluates the feasibility of such measurements. Finally, to test the validity of the full-field-based approach, the FEMU-identified parameters are compared against results obtained through a classical optimisation procedure based on force-elongation measurements from the shear zone. Full article

Porous sound absorption ceramic is one of the most promising materials for effectively eliminating noise pollution. However, its high production cost and low mechanical strength limit its practical applications. In this work, low-cost and in situ mullite whisker-reinforced porous sound-absorbing ceramics were prepared using recyclable construction waste and Al₂O₃ powder as the main raw materials, and AlF₃ and CeO₂ as the additives, respectively. The effects of CeO₂ content, AlF₃ content, and sintering temperature on the microstructure and properties of the porous ceramics were systematically investigated. The results showed that a small amount of CeO₂ significantly promoted the growth of elongated mullite crystals in the resultant porous ceramics, decreased the growth temperature of the mullite whiskers, and significantly increased the biaxial flexural strength. When 2 wt.% CeO₂ and 12 wt.% AlF₃ were added to the system, mullite whiskers were successfully obtained at a sintering temperature of 1300 °C for 1 h, which exhibited excellent properties, including an open porosity of 56.4 ± 0.6%, an average pore size of 1.32–2.54 μm, a biaxial flexural strength of 23.7 ± 0.9 MPa, and a sound absorption coefficient of >0.8 at 800–4000 Hz. Full article

The deformation behavior and microstructure of 6061 aluminum alloy processed by severe plastic deformation (SPD) using biaxial alternate forging that can evaluate the forming limit and mechanical properties of alloys, simultaneously, were investigated in this study. A finite element (FE) analysis on the biaxial alternating forging process, considering the strain-hardening coefficient and forging pass of the material, was conducted. When the strain-hardening coefficient is 0, an average effective strain of 440% was found within a diameter of 4 mm in the core of the workpiece after eight passes, while it was 300% at the same pass number when the strain-hardening coefficient was 0.2. The average effective strain estimated from the FE analysis was about 264% after eight passes of forging, which is considered to be a level of SPD that significantly exceeds the elongation of the raw material. As a result of the tensile test according to the forging pass, after two passes, the strength of the material could be gradually improved without significant degradation of elongation. Even though a large strain of 264% was found after eight passes were applied, deformed grains and twins with no recrystallized structure in optical microstructures with different forging passes were found. Full article

During orthodontic tooth movement (OTM), areas of compressive and tensile forces are generated in the periodontal ligament (PdL), a mechanoreactive connective tissue between the teeth and alveolar bone. Mechanically stimulated PdL fibroblasts (PdLFs), the main cell type of PdL, express significantly increased levels of growth differentiation factor 15 (GDF15). In compressed PdL areas, GDF15 plays a fundamental role in modulating relevant OTM processes, including inflammation and osteoclast activation. However, the specific function of this factor in tensile areas has not yet been investigated. Thus, the aim of this study was to investigate the role of GDF15 in the mechanoresponse of human PdLFs (hPdLFs) that were exposed to biaxial tensile forces in vitro. Using siRNA-mediated knockdown experiments, we demonstrated that GDF15 had no impact on the anti-inflammatory force response of elongated hPdLFs. Although the anti-inflammatory markers IL1RN and IL10, as well as the activation of immune cells remained unaffected, we demonstrated an inhibitory role of GDF15 for the IL-37 expression. By analyzing osteogenic markers, including ALPL and RUNX2, along with an assessment of alkaline phosphatase activation, we further showed that the regulation of IL-37 by GDF15 modulates the osteogenic differentiation potential of hPdLFs. Despite bone resorption in tensile areas being rather limited, GDF15 was also found to positively modulate osteoclast activation in those areas, potentially by adjusting the IL-37 levels. In light of our new findings, we hypothesize that GDF15 modulates force-induced processes in tissue and bone remodeling through its various intra- and extracellular signaling pathways as well as interaction partners. Potentially acting as a master regulator, the modulation of GDF15 levels may hold relevance for clinical implications. Full article

Bubble growth processes are highly influenced by the elongational viscosity of the blowing agent-loaded polymer melt. Therefore, the elongational viscosity is an important parameter for the development of new polymers for foaming applications, as well as for the prediction of bubble growth processes. Thus, knowledge of the initial expansion and deformation behavior in dependency on the polymer, the blowing agent concentration, and the process conditions is necessary. This study presents a novel method for the in-line observation and analysis of the initial expansion and deformation behavior within the bead foam extrusion process. For this purpose, nitrogen as the blowing agent was injected into the polymer melt (PS and PLA) during the extrusion process. The in-line observation system consists of a borescope equipped with a camera, which was integrated into the water box of an underwater pelletizer. The camera is controlled by a developed trigger by means of angular step signal analysis of a rotary encoder on the cutter shaft of the underwater pelletizer. Thus, images can be taken at any time during the foaming process depending on the cutter position to the die outlet. It is shown that the developed method provides reliable results and that the differences of the initial expansion and deformation behavior during bubble growth can be analyzed in-line in dependency on real foaming process conditions and the type of polymer used. Full article

Strain energy density functions are used in CAE analysis of hyperelastic materials such as rubber and elastomers. This function can originally be obtained only by experiments using biaxial deformation, but the difficulty of such experiments has made it almost impossible to put the function to practical use. Furthermore, it has been unclear how to introduce the strain energy density function necessary for CAE analysis from the results of biaxial deformation experiments on rubber. In this study, parameters of the Ogden and Mooney–Rivlin approximations of the strain energy density function were derived from the results of biaxial deformation experiments on silicone rubber, and their validity was verified. These results showed that it is best to determine the coefficients of the approximate equations for the strain energy density function after 10 cycles of repeated elongation of rubber in an equal biaxial deformation state, followed by equal biaxial elongation, uniaxial constrained biaxial elongation, and uniaxial elongation to obtain these three stress–strain curves. Full article

The effect of a promising method of performing a thermomechanical treatment which provides the nanocrystalline structure formation in bulk NiTi shape memory alloy samples and a corresponding improvement to their properties was studied in the present work. The bi-axial severe plastic deformation of Ti-50.7at.%Ni alloy was carried out on the MaxStrain module of the Gleeble system at 350 and 330 °C with accumulated true strains of e = 6.6–9.5. The obtained structure and its mechanical and functional properties and martensitic transformations were studied using DSC, X-ray diffractometry, and TEM. A nanocrystalline structure with a grain/subgrain size of below 80 nm was formed in bulk nickel-enriched NiTi alloy after the MaxStrain deformation at 330 °C with e = 9.5. The application of MaxStrain leads to the formation of a nanocrystalline structure that is characterized by the appearance of a nano-sized grains and subgrains with equiaxed and elongated shapes and a high free dislocation density. After the MaxStrain deformation at 330 °C with e = 9.5 was performed, the completely nanocrystalline structure with the grain/subgrain size of below 80 nm was formed in bulk nickel-enriched NiTi alloy for the first time. The resulting structure provides a total recoverable strain of 12%, which exceeds the highest values that have been reported for bulk nickel-enriched NiTi samples. Full article

Due to the lack of raw material and forced by political demand, an increasing percentage of postconsumer materials (PCR) shall be used in all processing methods in polymer technology. Thermoforming, as one of the oldest polymer-processing methods, has special requirements regarding the melt stability at high temperatures. Low melt stability affects the thermoforming in a negative manner, as the low stiffness leads the sheet to sag during the heating phase. In this study, two-layer sheets are used in order to improve melt stability of PCR material. The focus is placed on the influence of rheological properties on the biaxial stretching behavior of mono- and two-layer sheets in partially molted state. In order to create a stabilizing layer, two different thermoformable virgin materials with a melt flow rate (MFR) of 3 g/10 min and 6 g/10 min were chosen. The second layer consists of instable PCR materials with a MFR of 16 g/10min and 50 g/10 min. Rheological investigations, molecular characterization and biaxial stretching tests are used to show the benefit of two-layer sheets for processing PCR material under elongational stress. The results show that the use of two-layer sheets can improve the biaxial stretching properties, so that two-layer sheets can offer a significant potential in the processing of PCR materials in thermoforming. Full article

To promote the application of the bamboo grid in the soil–rock mixture subgrade in mountain areas, the mechanical properties of bamboo reinforcement were investigated in this study, and the reinforcement effect and interface characteristics of uniaxial/biaxial bamboo grid on the soil–rock mixture under different vertical loads was comparatively analyzed. The results show that the tensile force (2% elongation) of the bamboo reinforcement is 50.21 kN/m, and its average tensile strength is 236.01 MPa. Moreover, bamboo reinforcement has excellent shear and flexural properties. In general, the reinforcement effect of the biaxial bamboo grid on the soil–rock mixed subgrade is better than that of the uniaxial bamboo grid. In the case of using a uniaxial bamboo grid, its pull-out curve is generally a strain-softening type. As for the biaxial bamboo grid, due to the existence of bite force, its pull-out curve usually presents a strain-hardening type. Compared with the uniaxial bamboo grid, the friction coefficient of the reinforcement–soil interface using the biaxial bamboo grid is higher, and the interfacial shear stress is increased by 72.2–91.2%. Full article

In order to ease the white pollution problem, biodegradable packaging materials are highly demanded. In this work, the biodegradable poly (butylene adipate-co-terephthalate)/MXene (PBAT/Ti₃C₂T_X) composite casting films were fabricated by melt mixing. Then, the obtained PBAT/Ti₃C₂T_X composite casting films were biaxially stretched at different stretching ratios so as to reduce the water vapor permeability rate (WVPR) and oxygen transmission rate (OTR). It was expected that the combination of Ti₃C₂T_X nanosheets and biaxial stretching could improve the water vapor and oxygen barrier performance of PBAT films. The scanning electron microscope (SEM) observation showed that the Ti₃C₂T_X nanosheets had good compatibility with the PBAT matrix. The presence of Ti₃C₂T_X acted as a nucleating agent to promote the crystallinity when the content was lower than 2 wt%. The mechanical tests showed that the incorporation of 1.0 wt% Ti₃C₂T_X improved the tensile stress, elongation at break, and Young’s modulus of the PBAT/Ti₃C₂T_X nanocomposite simultaneously, as compared with those of pure PBAT. The mechanical dynamical tests showed that the presence of Ti₃C₂T_X significantly improved the storage modulus of the PBAT nanocomposite in a glassy state. Compared with pure PBAT, PBAT-1.0 with 1.0 wt% Ti₃C₂T_X exhibited the lowest OTR of 782 cc/m²·day and 10.2 g/m²·day. The enhancement in gas barrier properties can be attributed to the presence of Ti₃C₂T_X nanosheets, which can increase the effective diffusion path length for gases. With the biaxial stretching, the OTR and WVPR of PBAT-1.0 were further reduced to 732 cc/m²·day and 6.5 g/m²·day, respectively. The PBAT composite films with enhanced water vapor and water barrier performance exhibit a potential application in green packaging. Full article

In ascending thoracic aortic aneurysms (ATAAs), aneurysm kinematics are driven by ventricular traction occurring every heartbeat, increasing the stress level of dilated aortic wall. Aortic elongation due to heart motion and aortic length are emerging as potential indicators of adverse events in ATAAs; however, simulation of ATAA that takes into account the cardiac mechanics is technically challenging. The objective of this study was to adapt the realistic Living Heart Human Model (LHHM) to the anatomy and physiology of a patient with ATAA to assess the role of cardiac motion on aortic wall stress distribution. Patient-specific segmentation and material parameter estimation were done using preoperative computed tomography angiography (CTA) and ex vivo biaxial testing of the harvested tissue collected during surgery. The lumped-parameter model of systemic circulation implemented in the LHHM was refined using clinical and echocardiographic data. The results showed that the longitudinal stress was highest in the major curvature of the aneurysm, with specific aortic quadrants having stress levels change from tensile to compressive in a transmural direction. This study revealed the key role of heart motion that stretches the aortic root and increases ATAA wall tension. The ATAA LHHM is a realistic cardiovascular platform where patient-specific information can be easily integrated to assess the aneurysm biomechanics and potentially support the clinical management of patients with ATAAs. Full article

Ductile-to-brittle transition (DBT) temperature and brittle fracture stress, σ_F, are important toughness criteria for structural materials. In this paper, low-carbon steels with an ultrafine elongated grain (UFEG) structure (transverse grain size 1.2 μm) and with two ferrite (α)-pearlite structure with grain sizes 10 µm and 18 µm were prepared. The UFEG steel was fabricated using multipass warm biaxial rolling. The tensile tests with a cylindrical specimen and three-point bending tests with a single-edge-notched specimen were performed at −196 °C. The local stress near the notch was quantitatively calculated via finite element analysis (FEA). The σ_F for each sample was quantified based on the experimental results and FEA. The relationship between σ_F and d_α in the wide range of 1.0 μm to 138 μm was plotted, including data from past literature. Finally, the conditions of grain size and temperature that cause DBT fracture in low-carbon steel were shown via the stress−d^−1/2 map. The results quantitatively showed the superiority of α grain size for brittle fracture. Full article