Search Results (1,470)

Blasting operations in surface mining pose a risk of flyrock, which is a critical safety concern for both personnel and infrastructure. This study presents the use of unmanned aerial vehicles (UAVs) and photogrammetric techniques to improve the accuracy of blast design, particularly in relation to controlling burden values and reducing flyrock. The research was conducted in a basalt quarry in Lower Silesia, where high rock fracturing complicated conventional blast planning. A DJI Mavic 3 Enterprise UAV was used to capture high-resolution aerial imagery, and 3D models were created using Strayos software. These models enabled precise analysis of bench face geometry and burden distribution with centimeter-level accuracy. The results showed a significant improvement in identifying zones with improper burden values and allowed for real-time corrections in blasthole design. Despite a ten-fold reduction in the number of images used, no loss in model quality was observed. UAV-based surveys followed software-recommended flight paths, and the application of this methodology reduced the flyrock range by an average of 42% near sensitive areas. This approach demonstrates the operational benefits and enhanced safety potential of integrating UAV-based photogrammetry into blasting design workflows. Full article

Aquatic vegetation plays a crucial role in freshwater ecosystems by providing habitats, regulating water quality, and supporting biodiversity. This study aims to monitor and analyze the dynamics of aquatic vegetation in Chimaditida Shallow Lake, Greece, using Sentinel-2 satellite imagery, with validation from field measurements. Data processing was performed using Google Earth Engine and QGIS. The study focuses on discriminating and mapping two classes of aquatic surface conditions: areas covered with Floating and Emergent Aquatic Vegetation and open water, covering all seasons from 1 March 2024, to 28 February 2025. Spectral bands such as B04 (red), B08 (near infrared), B03 (green), and B11 (shortwave infrared) were used, along with indices like the Modified Normalized Difference Water Index and Normalized Difference Vegetation Index. The classification was enhanced using Otsu’s thresholding technique to distinguish accurately between Floating and Emergent Aquatic Vegetation and open water. Seasonal fluctuations were observed, with significant peaks in vegetation growth during the summer and autumn months, including a peak coverage of 2.08 km² on 9 September 2024 and a low of 0.00068 km² on 28 December 2024. These variations correspond to the seasonal growth patterns of Floating and Emergent Aquatic Vegetation, driven by temperature and nutrient availability. The study achieved a high overall classification accuracy of 89.31%, with producer accuracy for Floating and Emergent Aquatic Vegetation at 97.42% and user accuracy at 95.38%. Validation with Unmanned Aerial Vehicle-based aerial surveys showed a strong correlation (R² = 0.88) between satellite-derived and field data, underscoring the reliability of Sentinel-2 for aquatic vegetation monitoring. Findings highlight the potential of satellite-based remote sensing to monitor vegetation health and dynamics, offering valuable insights for the management and conservation of freshwater ecosystems. The results are particularly useful for governmental authorities and natural park administrations, enabling near-real-time monitoring to mitigate the impacts of overgrowth on water quality, biodiversity, and ecosystem services. This methodology provides a cost-effective alternative for long-term environmental monitoring, especially in regions where traditional methods are impractical or costly. Full article

Coastal erosion, exacerbated by climate change, poses a critical global threat to both the environment and human livelihoods. Acquiring accurate, high-resolution topo-bathymetric data is vital for understanding these dynamic environments, without underestimating the hydrodynamic and meteo-oceanographic conditions. However, traditional methods often present significant challenges in achieving comprehensive, high-resolution topo-bathymetric coverage efficiently in shallow coastal zones, leading to a notable ”white ribbon” data gap. This study introduces a novel, integrated methodology combining unmanned aerial vehicles (UAVs) for terrestrial surveys, unmanned surface vehicles (USVs) for bathymetry, and the Global Navigation Satellite System (GNSS) for ground control and intertidal gap-filling. Through this technologically rigorous approach, a seamless Bathymetry-Topography Digital Surface Model for the Guardamar del Segura dune system (Spain) was successfully elaborated using a DJI Mini 2 UAV, Leica Zeno FLX100 GNSS, and Apache 3 USV. The method demonstrated a substantial time reduction of at least 50–75% for comparable high-resolution coverage, efficiently completing the 86.4 ha field campaign in approximately 4 h. This integrated approach offers an accessible and highly efficient solution for generating detailed coastal elevation models crucial for coastal management and research. Full article

Object detection in aerial images can provide great support in traffic planning, national defense reconnaissance, hydrographic surveys, infrastructure construction, and other fields. Objects in aerial images are characterized by small pixel–area ratios, dense arrangements between objects, and arbitrary inclination angles. In response to these characteristics and problems, we improved the feature extraction network Inception-ResNet using the Fast Architecture Search (FAS) module and proposed a one-stage anchor-free rotation object detector. The structure of the object detector is simple and only consists of convolution layers, which reduces the number of model parameters. At the same time, the label sampling strategy in the training process is optimized to resolve the problem of insufficient sampling. Finally, a decoupled object detection head is used to separate the bounding box regression task from the object classification task. The experimental results show that the proposed method achieves mean average precision (mAP) of 82.6%, 79.5%, and 89.1% on the DOTA1.0, DOTA1.5, and HRSC2016 datasets, respectively, and the detection speed reaches 24.4 FPS, which can meet the needs of real-time detection. Full article

The accurate monitoring of waterbird abundance and their habitat preferences is essential for effective ecological management and conservation planning in aquatic ecosystems. This study explores the efficacy of unmanned aerial vehicle (UAV)-based high-resolution orthomosaics for waterbird monitoring and mapping along the Lieve Canal, Belgium. We systematically classified habitats into residential, industrial, riparian tree, and herbaceous vegetation zones, examining their influence on the spatial distribution of three focal waterbird species: Eurasian coot (Fulica atra), common moorhen (Gallinula chloropus), and wild duck (Anas platyrhynchos). Herbaceous vegetation zones consistently supported the highest waterbird densities, attributed to abundant nesting substrates and minimal human disturbance. UAV-based waterbird counts correlated strongly with ground-based surveys (R² = 0.668), though species-specific detectability varied significantly due to morphological visibility and ecological behaviors. Detection accuracy was highest for coots, intermediate for ducks, and lowest for moorhens, highlighting the crucial role of image resolution ground sampling distance (GSD) in aerial monitoring. Operational challenges, including image occlusion and habitat complexity, underline the need for tailored survey protocols and advanced sensing techniques. Our findings demonstrate that UAV imagery provides a reliable and scalable method for monitoring waterbird habitats, offering critical insights for biodiversity conservation and sustainable management practices in aquatic landscapes. Full article

Handover (HO) management plays a key role in ensuring uninterrupted connectivity across evolving wireless networks. While previous generations such as 4G and 5G have introduced several HO strategies, these techniques are insufficient to meet the rigorous demands of sixth-generation (6G) networks in ultra-dense, heterogeneous smart city environments. Existing studies often fail to provide integrated HO solutions that consider key concerns such as energy efficiency, security vulnerabilities, and interoperability across diverse network domains, including terrestrial, aerial, and satellite systems. Moreover, the dynamic and high-mobility nature of smart city ecosystems further complicate real-time HO decision-making. This survey aims to highlight these critical gaps by systematically categorizing state-of-the-art HO approaches into AI-based, fuzzy logic-based, and hybrid frameworks, while evaluating their performance against emerging 6G requirements. Future research directions are also outlined, emphasizing the development of lightweight AI–fuzzy hybrid models for real-time decision-making, the implementation of decentralized security mechanisms using blockchain, and the need for global standardization to enable seamless handovers across multi-domain networks. The key outcome of this review is a structured and in-depth synthesis of current advancements, which serves as a foundational reference for researchers and engineers aiming to design intelligent, scalable, and secure HO mechanisms that can support the operational complexity of next-generation smart cities. Full article

The accurate and large-scale mapping of seagrass meadows is essential, as these meadows form primary habitats for marine organisms and large sinks for blue carbon. Image data available for mapping these habitats are often scarce or are acquired through multiple surveys and instruments, resulting in images of varying spatial and spectral characteristics. This study presents an unsupervised domain adaptation (UDA) strategy that combines histogram-matching with the transformer-based SegFormer model to address these challenges. Unoccupied aerial vehicle (UAV)-derived imagery (3-cm resolution) was used for training, while orthophotos from airplane surveys (12.5-cm resolution) served as the target domain. The method was evaluated across three Danish estuaries (Horsens Fjord, Skive Fjord, and Lovns Broad) using one-to-one, leave-one-out, and all-to-one histogram matching strategies. The highest performance was observed at Skive Fjord, achieving an F1-score/IoU = 0.52/0.48 for the leave-one-out test, corresponding to 68% of the benchmark model that was trained on both domains. These results demonstrate the potential of this lightweight UDA approach to generalization across spatial, temporal, and resolution domains, enabling the cost-effective and scalable mapping of submerged vegetation in data-scarce environments. This study also sheds light on contrast as a significant property of target domains that impacts image segmentation. Full article

Innovative applications of high-resolution airborne imaging are explored for detecting grapevine diseases. Driven by the motivation to enhance early disease detection, the method’s effectiveness lies in its capacity to identify isolated cases of grapevine yellows (Flavescence dorée and Bois Noir) and trunk disease (Esca complex), crucial for preventing the disease from spreading to unaffected areas. Conducted over a 17 ha vineyard in the Forlì municipality in Emilia-Romagna (Italy), the aerial survey utilized a photogrammetric camera capturing centimeter-level resolution images of the whole area in 17 minutes. These images were then processed through an automated analysis leveraging RGB-based spectral indices (Green–Red Vegetation Index—GRVI, Green–Blue Vegetation Index—GBVI, and Blue–Red Vegetation Index—BRVI). The analysis scanned the 1.24 · 10⁹ pixels of the orthomosaic, detecting 0.4% of the vineyard area showing evidence of disease. The instances, density, and incidence maps provide insights into symptoms’ spatial distribution and facilitate precise interventions. High specificity (0.96) and good sensitivity (0.56) emerged from the ground field observation campaign. Statistical analysis revealed a significant edge effect in symptom distribution, with higher disease occurrence near vineyard borders. This pattern, confirmed by spatial autocorrelation and non-parametric tests, likely reflects increased vector activity and environmental stress at the vineyard margins. The presented pilot study not only provides a reliable detection tool for grapevine diseases but also lays the groundwork for an early warning system that, if extended to larger areas, could offer a valuable system to guide on-the-ground monitoring and facilitate strategic decision-making by the authorities. Full article

Stand structural configuration dictates ecosystem functional performance. Mangrove ecosystems, located in ecologically sensitive coastal ecotones, require efficient acquisition of stand structure parameters and health assessments based on these parameters for practical applications. Effective assessment of mangrove ecosystem health, crucial for their functional performance in ecologically sensitive coastal ecotones, relies on efficient acquisition of stand structure parameters. This study developed a UAV (Unmanned Aerial Vehicle)-based framework for mangrove health evaluation integrating stand structure parameters, utilizing UAV visible-light imagery, field plot surveys, and computer vision techniques, and applied it to the assessment of a national nature reserve. We obtained the following results: (1) A deep neural network, combining UAV visible-light data with tree height constraints, achieved 88.29% overall accuracy in simultaneously identifying six dominant mangrove species; (2) Stand structure parameters were derived based on individual tree extraction results in seedling zones along forest edges (with canopy individual tree segmentation accuracy ≥ 78.57%), and a stand health evaluation model was constructed; (3) Health assessment revealed that the core zone exhibited significantly superior stand health compared to non-core zones. This method demonstrates high efficiency, significantly reducing the time and effort for monitoring, and offers robust support for future mangrove forest health assessments and adaptive conservation strategies. Full article

Flying wing Unmanned Aerial Vehicles (UAVs) are an interesting flight configuration, considering its benefits over aerodynamic, structural and added stealth aspects. The existing configurations are thoroughly studied from the literature survey and useful observations with respect to design and analysis are obtained. The proposed design method includes distinct calculations of the UAV and modelling using 3D experience. The created innovative models are simulated with the help of computational fluid dynamics techniques in ANSYS Fluent to obtain the aerodynamic parameters such as forces, pressure and velocity. The optimization process continues to add more desired modifications to the model, to finalize the best design of flying wing frame for the chosen application and mission profile. In total, nine models are developed starting with the base model, then leading to the conventional, advanced and nature inspired configurations such as the falcon and dragonfly models, as it has an added advantage of producing high maneuverability and lift. Following this, fluid structure interaction analysis has been performed for the best performing configurations, resulting in the determination of variations in the structural behavior with the imposition of advanced composite materials, namely, boron, Kevlar, glass and carbon fiber-reinforced polymers. In addition to this, a hybrid material is designed by combining two composites that resulted in superior material performance when imposed. Control dynamic study is performed for the maneuvers planned as per mission profile, to ensure stability during flight. All the resulting parameters obtained are compared with one another to choose the best frame of the flying wing body, along with the optimum material to be utilized for future analysis and development. Full article

Debris flows pose significant risks to mountainous regions, and quick, accurate volume estimation is crucial for hazard assessment and post-disaster response. Traditional volume estimation methods, such as ground surveys and aerial photogrammetry, are often limited by cost, accessibility, and timeliness. While remote sensing offers wide coverage, existing optical and Synthetic Aperture Radar (SAR)-based techniques face challenges in direct volume estimation due to resolution constraints and rapid terrain changes. This study proposes a Super-Resolution Shape from Shading (SRSFS) approach enhanced by a Non-local Piecewise-smooth albedo Constraint (NPC), hereafter referred to as NPC SRSFS, to estimate debris-flow erosion volume using single high-resolution optical satellite imagery. By integrating publicly available global Digital Elevation Model (DEM) data as prior terrain reference, the method enables accurate post-disaster topography reconstruction from a single optical image, thereby reducing reliance on stereo imagery. The NPC constraint improves the robustness of albedo estimation under heterogeneous surface conditions, enhancing depth recovery accuracy. The methodology is evaluated using Gaofen-6 satellite imagery, with quantitative comparisons to aerial Light Detection and Ranging (LiDAR) data. Results show that the proposed method achieves reliable terrain reconstruction and erosion volume estimates, with accuracy comparable to airborne LiDAR. This study demonstrates the potential of NPC SRSFS as a rapid, cost-effective alternative for post-disaster debris-flow assessment. Full article

The unique vegetation in riparian zones is fundamental for various ecological and socio-economic functions in these transitional areas. Sustainable management requires detailed spatial information about the occurring flora. Here, we present a Deep Learning (DL)-based approach for processing multimodal high-resolution remote sensing data (aerial RGB and near-infrared (NIR) images and elevation maps) to generate a classification map of the tidal Elbe and a section of the Rhine River (Germany). The ground truth was based on existing mappings of vegetation and biotope types. The results showed that (I) despite a large class imbalance, for the tidal Elbe, a high mean Intersection over Union (IoU) of about 78% was reached. (II) At the Rhine River, a lower mean IoU was reached due to the limited amount of training data and labelling errors. Applying transfer learning methods and labelling error correction increased the mean IoU to about 60%. (III) Early fusion of the modalities was beneficial. (IV) The performance benefits from using elevation maps and the NIR channel in addition to RGB images. (V) Model uncertainty was successfully calibrated by using temperature scaling. The generalization ability of the trained model can be improved by adding more data from future aerial surveys. Full article

Unmanned Aerial Vehicles (UAVs) have become increasingly prevalent in both governmental and civilian applications, offering significant reductions in operational costs by minimizing human involvement. There is a growing demand for autonomous, scalable, and intelligent coordination strategies in complex aerial missions involving multiple Unmanned Aerial Vehicles (UAVs). Traditional control techniques often fall short in dynamic, uncertain, or large-scale environments where decentralized decision-making and inter-agent cooperation are crucial. A potentially effective technique used for UAV fleet operation is Multi-Agent Reinforcement Learning (MARL). MARL offers a powerful framework for addressing these challenges by enabling UAVs to learn optimal behaviors through interaction with the environment and each other. Despite significant progress, the field remains fragmented, with a wide variety of algorithms, architectures, and evaluation metrics spread across domains. This survey aims to systematically review and categorize state-of-the-art MARL approaches applied to UAV control, identify prevailing trends and research gaps, and provide a structured foundation for future advancements in cooperative aerial robotics. The advantages and limitations of these techniques are discussed along with suggestions for further research to improve the effectiveness of MARL application to UAV fleet management. Full article

Fish kills are sudden mass mortalities that occur in freshwater and marine systems worldwide. Fish kill surveys are essential for assessing the ecological and economic impacts of fish kill events, but are often labor-intensive, time-consuming, and spatially limited. This study aims to address these challenges by exploring the application of unoccupied aerial systems (or drones) and deep learning techniques for coastal fish carcass detection. Seven flights were conducted using a DJI Phantom 4 RGB quadcopter to monitor three sites with different substrates (i.e., sand, rock, shored Sargassum). Orthomosaics generated from drone imagery were useful for detecting carcasses washed ashore, but not floating or submerged carcasses. Single shot multibox detection (SSD) with a ResNet50-based model demonstrated high detection accuracy, with a mean average precision (mAP) of 0.77 and a mean average recall (mAR) of 0.81. The model had slightly higher average precision (AP) when detecting large objects (>42.24 cm long, AP = 0.90) compared to small objects (≤14.08 cm long, AP = 0.77) because smaller objects are harder to recognize and require more contextual reasoning. The results suggest a strong potential future application of these tools for rapid fish kill response and automatic enumeration and characterization of fish carcasses. Full article

Compliant force control is a fundamental capability for enabling robots to interact safely and effectively with dynamic and uncertain environments. This paper presents a comprehensive survey of compliant force control strategies, intending to enhance safety, adaptability, and precision in applications such as physical human–robot interaction, robotic manipulation, and collaborative tasks. The review begins with a classification of compliant control methods into passive and active approaches, followed by a detailed examination of direct force control techniques—including hybrid and parallel force/position control—and indirect methods such as impedance and admittance control. Special emphasis is placed on advanced compliant control strategies applied to structurally complex robotic systems, including aerial, mobile, cable-driven, and bionic robots. In addition, intelligent compliant control approaches are systematically analyzed, encompassing neural networks, fuzzy logic, sliding mode control, and reinforcement learning. Sensorless compliance techniques are also discussed, along with emerging trends in hardware design and intelligent control methodologies. This survey provides a holistic view of the current landscape, identifies key technical challenges, and outlines future research directions for achieving more robust, intelligent, and adaptive compliant force control in robotic systems. Full article