Search Results (435)

Mixed amine/sulfolane (TMS) biphasic solutions have gained attention for their adjustable structure–activity relationships and lower regeneration energy. In this study, monoethanolamine (MEA) is employed as the main absorbent and polyamine as the co-absorbent, which are subsequently mixed with the phase separation promoter sulfolane (TMS) to form ternary biphasic solvent systems. Polyamine co-absorbents include 3-Dimethylaminopropylamine (DMAPA), 3-Diethylaminopropylamine (DEAPA), and Diethylenetriamine (DETA). Phase separation, absorption, and desorption performances were systematically studied. Reaction and phase separation mechanisms were elucidated through ¹³C nuclear magnetic resonance (NMR) spectroscopy. The overall mass transfer coefficients (K_G) were measured using a wetted wall column (WWC). Variations in the amine-to-sulfolane concentration ratio showed minimal impact on phase volume, while temperature and solvent composition significantly influenced phase separation behavior. All three solvents exhibited superior CO₂ capture performance, with CO₂ loadings in the rich phases ranging from 4.09 to 4.71 mol/L and over 96.82% of CO₂ concentrated in them, cyclic capacities reached or exceeded 3 mol/L, and regeneration energy consumption was 29.63–55.51% lower than 5 M MEA. ¹³C NMR analysis indicated that multiple N atoms in polyamines promoted the formation of additional ionic species during CO₂ absorption, thereby enhancing phase separation completeness. Furthermore, K_G values for the ternary systems exceeded that of conventional MEA, with the MEA/DEAPA/TMS system exhibiting a 1.7-fold increase. These findings demonstrated the industrial potential of MEA/polyamine/TMS biphasic solvents for efficient CO₂ capture. Full article

Encapsulated formulations have emerged as a promising tool for increasing nutrient absorption in the food supplement and cosmetic industries. Although the theoretical amplification factors for improving the bioavailability of encapsulated formulations are very high for poorly soluble active compounds, it has long been known that encapsulation can also enhance the absorption of water-soluble ingredients. These findings have led to the development of new technologies for encapsulating nutrients for use in the food industry. However, accurate quantification of nutrients in encapsulated formulations in the food supplement industry remains a challenge. This study presents the development and validation of novel analytical procedures for determining artemisinin in various food supplement formulations. Three formulations were prepared using different emulsifying procedures for artemisinin encapsulation. High-performance liquid chromatography with UV/Vis detection (HPLC-UV/Vis) was used for analysis. Separation was performed using a Waters ACQUITY Premier BEH C18 column. Specialized sample preparation procedures were designed to efficiently disrupt encapsulation and extract artemisinin for precise quantification. Three different sample preparation procedures were required to accurately determine the artemisinin content in the tested formulations. All methods were validated. The precision, linearity expressed as R², LOD, and LOQ of the chromatographic method were 0.39%, 0.9995, 18 µg/mL, and 26 µg/mL, respectively. Recoveries of the sample preparation methods were above 94%. The developed procedures enable accurate determination of artemisinin in encapsulated formulations, ensuring product quality and safety. These findings suggest that, for quality control of encapsulated food products, specialized analytical procedures for individual formulations may need to be developed and validated. Full article

Circular concrete-filled steel tube columns prepared with 100% recycled aggregate concrete (RACFST) are of interest for sustainable, carbon-neutral construction. However, recycled aggregates typically have higher water absorption and lower stiffness, raising concerns about seismic performance. This paper investigates the low-cycle cyclic behavior and displacement ductility of circular RACFST columns. Ten short columns were tested under an axial load ratio of ≈0.20, with varying diameters of 165 and 219 mm and concrete strengths of C30, C40, and C50, along with companion natural-aggregate CFST control specimens. A three-dimensional finite element model was developed and calibrated based on the test results, and parametric simulations were conducted to study the effects of geometry and material parameters. Two distinct flexural failure modes with outward bulging at the base were observed. These two distinct flexural failure modes refer to (1) local outward bulging of the steel tube accompanied by buckling near the base (e.g., specimens RACFSTC40-165-1 and RACFSTC30-219-1) and (2) flexural yielding with extensive concrete crushing around the base region (e.g., specimens RACFSTC50-219-2 and FSTC40-219-2). The first mode was characterized by early steel local deformation and shell instability, while the second showed more distributed plasticity with crushing of recycled aggregate concrete. These modes underline the influence of D/t and concrete strength on failure progression. The results indicate that RACFST columns attain a peak strength comparable to conventional CFST, while achieving significantly greater drift ductility and energy dissipation; the equivalent viscous damping ratio was found to increase with drift at ≈0.04–0.08 for low drifts and ≈0.10–0.18 for moderate drifts, suggesting that existing CFST design provisions are applicable, with only a minor ~3–5% reduction in core concrete strength recommended for stability. Full article

Oil and grease (O&G) pollution in municipal effluents represents a critical environmental challenge. This study contributes a novel experimental assessment of how pressure and recirculation time influence oxygen transfer, microbubble generation, and pollutant removal in a pilot-scale DAF system, providing new insights into process optimization for municipal wastewater treatment. This study evaluated the efficiency of a DAF system in removing organic pollutants and solids from municipal effluent by varying gauge pressure (1–5 bar) and recirculation time (1–20 min). The initial concentrations present in the effluent were 800 mg/L total solids (TS), 590 mg/L total suspended solids (TSS), 450 mg/L oil and grease (O&G), 360 mg/L biochemical oxygen demand (BOD₅), and 710 mg/L chemical oxygen demand (COD). The concentration of dissolved air (interpreted as dissolved oxygen supersaturation) reached 102.3 mg/L and removal efficiencies of 84.4% for O&G, 88.9% for BOD₅, 88.7% for COD, and 85% for TSS were achieved, while pH and dissolved solids (DS) remained stable. The saturation factor (f = 0.8) confirmed efficient oxygen-liquid transfer, attributed to the use of Raschig rings in the absorption column. The significance of this work lies in demonstrating that operating conditions directly enhance oxygen dissolution and flotation performance, highlighting an optimization pathway rarely reported for municipal effluents. The results demonstrate that DAF is a robust, stable, and energy-efficient technology capable of effectively removing organic and lipid loads from municipal effluent, providing a sustainable alternative for the pretreatment and reuse of urban wastewater. Full article

This study investigated the effects of irrigation water salinity on the soil–water characteristic curve (SWCC) using soil samples collected from a typical irrigated area in Yingjisha County, southern Xinjiang. The SWCC was determined experimentally via centrifugation. The correlation degree among influencing factors was evaluated, and a goodness-of-fit assessment of mainstream traditional SWCC models was conducted using MATLAB 2021a. A modified Van Genuchten (VG) model incorporating the influence of irrigation water salinity was developed. The accuracy and reliability of the proposed model were validated through soil column infiltration experiments and numerical simulations. The results demonstrated that the original VG model provided the best fit for loam soils in southern Xinjiang, albeit with non-negligible deviations, indicating the need for further refinement. Significant correlations were identified between soil characteristic indices and model parameters, ranked in descending order of influence as follows: soil dry bulk density > clay content > inorganic salt content > silt content. Soils with higher clay and silt contents, along with greater bulk density, exhibited enhanced water retention capacity, resulting in a flatter SWCC. Although increased irrigation water salinity initially improved the soil’s water absorption capacity, the rate of enhancement gradually diminished with further increases in salinity, ultimately leading to a reduction in overall water retention performance. This study provides a theoretical foundation for the prevention and amelioration of saline soils and also supports the efficient utilization of water resources. Full article

The methanol-to-olefins (MTO) process offers a viable alternative to traditional naphtha cracking for producing light olefins, providing flexibility in feedstock sources and the potential for reduced energy consumption. This study presents a detailed plant-wide design of an MTO process, developed and optimized to increase ethylene and propylene yields while reducing energy consumption. The methodology includes comprehensive reactor modeling of a fast fluidized-bed reactor–regenerator system, accounting for coke formation kinetics, along with rigorous process simulation for the subsequent separation and purification of products. A six-column distillation train has been designed and optimized for the recovery of polymer-grade ethylene and propylene, while dual-stage CO₂ absorption units ensure complete removal of carbon dioxide. Pinch analysis is used to identify opportunities for heat integration, resulting in an optimized heat-exchanger network that significantly reduces the need for external heating and cooling utilities. The results show that the optimized MTO design achieves a methanol conversion rate of over 99.9% and produces a propylene-rich product stream with a propylene-to-ethylene ratio of approximately 1.8, while maintaining a high purity level exceeding 99.5%. By implementing heat integration and recycling by-products, including using off-gas methane as furnace fuel and repurposing waste heat for steam generation, the plant reduces utility requirements by more than 85%, significantly improving energy efficiency. An economic evaluation shows a favorable payback period of approximately 5.4 years and an internal rate of return of 15–16%, confirming the viability and industrial potential of the integrated MTO process for sustainable olefin production. Full article

Dendrobium moschatum neutral polysaccharide (DMP-NP) was isolated using a water extraction–ethanol precipitation method, followed by purification with DEAE-cellulose anion-exchange resin and a dextran gel column. The resulting DMP-NP1 exhibited a weight-average molecular weight of 16.23 kDa. The molar ratio of monosaccharides was as follows: glucose–mannose–galactose–fucose–rhamnose = 78.54:19.11:1.59:0.53:0.23, with a glucose-to-mannose ratio of 4.1:1. Infrared spectroscopic analysis revealed characteristic carbohydrate absorption peaks and confirmed the presence of pyranosidic linkages. NMR analysis revealed that DMP-NP1 possesses a backbone mainly formed by 1→4 glycosidic linkages, a small number of 1→6 branches, and O-acetyl substitutions at the C2 and C3 positions of mannose residues. In vitro experiments demonstrated that treatment with 0–20 μg/mL (0–1.23 μM) DMP-NP significantly enhanced the activities of catalase (CAT) and superoxide dismutase (SOD) in IPEC-J2 cells, along with upregulation of the corresponding antioxidant genes. Concurrently, DMP-NP reduced the secretion of key pro-inflammatory cytokines, including TNF-α, IL-1β, and IL-6, and downregulated the expression of genes associated with both antioxidant and inflammatory signaling pathways. Collectively, these findings indicate that DMP-NP not only prevents but also ameliorates LPS-induced inflammatory injury in intestinal epithelial cells, thereby providing a basis for the application of DMP-NP in intestinal inflammation mitigation. Full article

Carbon emission reduction strategies are crucial for addressing global climate change, with chemical absorption-based carbon capture technology being one of the core methods for achieving large-scale CO₂ mitigation. The current research focus in chemical absorption lies in selecting blended amine–catalyst systems and applying efficient absorption–desorption equipment. This study employs the Lattice Boltzmann Method (LBM) to simulate the catalytic CO₂ absorption process within an absorption column, obtaining data such as solution flow velocity, CO₂ absorption rate, and temperature distribution. The simulation results align well with experimental data from a continuous pilot-scale setup. Furthermore, the effects of different operating parameters and catalyst conditions on the absorption process were investigated. The findings indicate that higher catalyst volume fractions and smaller catalyst particle sizes enhance CO₂ absorption but may also lead to significant temperature rises across the column. Additionally, an optimized ternary amine–catalyst combination should be selected over a single amine to achieve superior CO₂ absorption capacity. Provided that the cyclic loading capacity is maintained, the absorbent solution flow rate should be minimized to ensure optimal absorption efficiency. Full article

Blast damage to structural members poses serious risks to both buildings and people, making it important to understand how these elements behave under extreme loads. Columns in reinforced concrete (RC) structures are especially critical, as their sudden failure can trigger progressive collapse, unlike beams or slabs that have more redundancy. This state-of-the-art review brings together the current knowledge of the blast response of RC columns, focusing on their failure patterns, dynamic behavior, and key loading mechanisms. The studies covered include experiments, high-fidelity numerical simulations, emerging machine learning approaches, and analytical models for columns of different shapes (square, rectangular, circular) and strengthening methods, such as fiber reinforcement, steel-concrete composite confinement, and advanced retrofitting. Composite columns are also reviewed to compare their hybrid confinement and energy-absorption advantages over conventional RC members. Over forty specific studies on RC columns were analyzed, comparing the results based on geometry, reinforcement detailing, materials, and blast conditions. Both near-field and contact detonations were examined, along with factors like axial load, standoff distance, and confinement. This review shows that RC columns respond very differently to blasts depending on their shape and reinforcement. Square, rectangular, and circular sections fail in distinct ways. Use of ultra-high-performance concrete, steel fibers, steel-concrete composite, and fiber-reinforced polymer retrofits greatly improves peak and residual load capacity. Ultra-high-performance concrete can retain a significantly higher fraction of axial load (often >70%) after strong blasts, compared to ~40% in conventional high-strength RC under similar conditions. Larger sections, closer stirrups, higher transverse reinforcement, and good confinement reduce spalling, shear failure, and mid-height displacement. Fiber-reinforced polymer and steel-fiber wraps typically improve residual strength by 10–15%, while composite columns with steel cores remain stiff and absorb more energy post-blast. Advanced finite element simulations and machine learning models now predict displacements, damage, and residual capacity more accurately than older methods. However, gaps remain. Current design codes of practice simplify blast loads and often do not account for localized damage, near-field effects, complex boundary conditions, or pre-existing structural weaknesses. Further research is needed on cost-effective, durable, and practical retrofitting strategies using advanced materials. This review stands apart from conventional literature reviews by combining experimental results, numerical analysis, and data-driven insights. It offers a clear, quantitative, and comparative view of RC column behavior under blast loading, identifies key knowledge gaps, and points the way for future design improvements. Full article

This study presents a technique for categorizing Aedes aegypti mosquitoes infected with the Zika virus under laboratory conditions. Our approach involves the utilization of the near-infrared spectroscopy technique and machine learning algorithms. The model developed utilizes the absorption of light from 350 to 1000 nm. It integrates Linear Discriminant Analysis (LDA) of the signal’s windowed version to exploit non-linearities, along with Support Vector Machine (SVM) for classification purposes. Our proposed methodology can identify the presence of the Zika virus in intact mosquitoes with a balanced accuracy of 96% (row C2HT, average of columns TPR (%) and SPC (%)) when heads/thoraces of mosquitoes are scanned at 4, 7, and 10 days post virus infection. The model was 97.1% (10 DPI, row C2AB, column ACC (%)) accurate for mosquitoes that were used to test it, i.e., mosquitoes scanned 10-days post-infection and mosquitoes whose abdomens were scanned. Notable benefits include its cost-effectiveness and the capability for real-time predictions. This work also demonstrates the role played by different spectral wavelengths in predicting an infection in mosquitoes. Full article

The Directional Polarimetric Camera (DPC) onboard the Gaofen-5 (02) satellite includes gas absorption bands that are crucial for the quantitative retrieval of clouds, atmospheric aerosols, and surface parameters. However, in-flight radiometric calibration of these bands remains challenging due to strong absorption features and the lack of onboard calibration devices. In this study, a calibration method that exploits functional relationships between the reflectance ratios of gas absorption and adjacent reference bands and key surface–atmosphere parameters over sunglint were presented. Radiative transfer simulations were combined with polynomial fitting to establish these relationships, and prior knowledge of surface pressure and water vapor column concentration was incorporated to achieve high-precision calibration. Results show that the calibration uncertainty of the oxygen absorption band is mainly driven by surface pressure, with a total uncertainty of 3.01%. For the water vapor absorption band, uncertainties are primarily associated with water vapor column concentration and surface reflectance, yielding total uncertainties of 3.45%. Validation demonstrates the robustness of the proposed method: (1) cross-calibration using desert samples confirms the stability of the results, and (2) the retrieved surface pressure agrees with the DEM-derived estimates, and the retrieved total column water vapor agrees with the MODIS products, confirming the calibration. Overall, the method provides reliable in-flight calibration of DPC gas absorption bands on Gaofen-5 (02) and can be adapted to similar sensors with comparable spectral configurations. Full article

Gnetol (trans-2,3′,5′,6-tetrahydroxystilbene), a naturally occurring stilbene structurally related to resveratrol (trans-3,5,4′-trihydroxystilbene; RES), has been reported to possess multiple health-promoting activities. In order to support its potential nutraceutical application, a reliable chromatography–tandem mass spectrometry (LC–MS/MS) assay was developed and validated for the quantitative determination of gnetol in mouse plasma and tissue samples, using isotopically labeled RES-¹³C₆ serving as the internal standard (IS). Electrospray ionization (ESI) was performed in negative mode, with multiple reaction monitoring (MRM) transitions m/z 243.2 → 175.0 for gnetol and m/z 233.1 → 191.0 for the IS. Chromatographic separation was achieved on a reversed-phase HPLC column using a 5-min gradient delivery of acetonitrile and 2 mM ammonium acetate at 0.5 mL/min and 40 °C. The linear calibration curve covered the concentration range of 5.0–1500 ng/mL, and the method validation confirmed its selectivity, accuracy, precision, stability, and dilution integrity. The developed method was subsequently applied to a biodistribution study in mice after oral administration of gnetol at 400 µmol/kg (equivalent to 97.7 mg/kg). Gnetol was rapidly absorbed and extensively distributed in key pharmacologically relevant organs. Despite its poor aqueous solubility, oral uptake was not significantly hindered. Collectively, these findings demonstrate that gnetol exhibits favorable absorption and tissue distribution profiles, supporting its promise as a candidate for nutraceutical development. Full article

In order to establish a general design methodology for water-based electromagnetic metamaterial absorber microstructures, a topology optimization method for water-based metamaterial absorber microstructures design was proposed in this paper. According to Mie resonance and impedance matching theory, the realization mechanism and physical model of the broadband water-based metamaterial absorber were constructed. The highest average in-band absorption rate was taken as the design object; the topological optimization model for water-based metamaterial absorber design was established. A metamaterial absorber microstructure with 16 discretized water columns inside the unit cell was designed as an example. The obtained structure exhibited a very high average in band absorption rate in the specific frequency band. The proposed method was a collaborative optimization approach that employed a single type of design variable, namely water column height, to simultaneously adjust surface impedance matching and specific resonant modes. It provided a feasible method for achieving the highest average absorption rate within a specific band. Full article

Scaffolds are temporary structures that workers usually use during building or repair work. These structures can be built in different shapes and types depending on the type of joints to which the beams and columns of the scaffolds are connected. Due to their temporary nature, they are very sensitive to vibration under dynamic or static actions, and this causes many accidents and unstable behaviours in them. This unstable behaviour has different reasons, including bracing conditions and slenderness of the columns, stiffness of joints and anchors, imperfections in the construction, damage and corrosion due to climate change, etc. This article aims to reanalyse the mechanical properties of scaffold joints and anchors and obtain some critical factors in the overall stability of the mentioned structures, including load-bearing capacity, initial stiffness, energy absorption, and ductility. To this aim, some recent research on scaffolds has been summarised and discussed, and then the failure mode and mechanical behaviour of the scaffolds in different types of scaffold joints and anchors have been estimated and considered from previous studies. Moreover, some mechanical properties, including ductility, initial stiffness, and energy absorption, have been estimated and developed based on the force-displacement curves of previous studies. The results highlight the crucial importance of the mechanical properties and behaviour of anchors and joints in estimating the behaviour and stability of scaffolds. The results also revealed that determining the mechanical characteristics of the mentioned elements can have a significant influence on the optimisation and design of scaffolds more accurately and predictably. Moreover, determining the mechanical properties of the anchors and joints can enhance our insights and understanding of how the mentioned parameters can improve the behaviour, stability, and safety of the scaffold structures. Full article

Isorhapontigenin (trans-3,5,4′-trihydroxy-3′-methoxystilbene; ISO), a dietary derivative of resveratrol (trans-3,5,4′-trihydroxystilbene; RES), exhibits diverse health-promoting properties. To facilitate its potential development as a nutraceutical, a simple and reliable high-performance liquid chromatography (HPLC) method was developed and validated for the quantification of ISO in various murine biological matrices. Chromatographic separation was achieved with a reversed-phase HPLC column through a 17 min gradient delivery of a mixture of acetonitrile and formic acid (0.1% v/v) at a flow rate of 1.5 mL/min at 50 °C. Quantification was performed using ultraviolet (UV) detection at 325 nm, with a lower limit of quantification (LLOQ) of 15 ng/mL in both plasma and tissue homogenate samples. The method demonstrated excellent selectivity, accuracy, and precision, and ISO remained stable under the tested conditions. This method was subsequently employed to investigate the tissue distribution of ISO in mice following oral administration at a dose of 200 µmol/kg (equivalent to 51.7 mg/kg). ISO was rapidly absorbed and extensively distributed across major pharmacologically relevant organs. Despite its limited aqueous solubility, its oral absorption was not significantly compromised. Given its oral bioavailability and broad tissue distribution, ISO represents a promising candidate for further nutraceutical development. Full article