Search Results (161)

Technological development in surface treatment for biomedical implants has advanced rapidly, yet the integration of additive manufacturing with controlled nano topography remains underexplored. This study investigates a novel bioactive kinetic screw (BKS) produced by 3D printing and CNC machining, followed by different anodization treatments: plasma electrolytic oxidation (PEO), hard anodization (HA), and soft anodization for TiO₂ nanotube (TNT) formation. Scanning electron microscopy revealed that PEO created a uniform macro–micro porous surface with pore sizes ranging from 5–15 µm and porosity values of 22.4 ± 3.2%, while HA produced smaller, less homogeneous pores (0.5–2 µm, porosity 10.7 ± 2.6%). TNTs were successfully formed with an average diameter of 80 ± 12 nm, although distribution was non-uniform in screw grooves. Preliminary finite element analysis demonstrated that Ti6Al4V nanotubes (diameter 50 nm, length 500 nm) withstood applied torque with maximum von Mises stress of 1.5 × 10⁻⁸ N/nm² and maximum strain of 3.56, indicating mechanical resilience compatible with early implant loading. The findings demonstrate that the proposed anodization protocols generate distinct hierarchical surface morphologies on BKS implants while preserving implant geometry. These results provide a structural basis for future investigations of biological performance. Full article

To improve the wear resistance of 45 steel, nano-agglomerated Al₂O₃-TiO₂-CeO₂/carbon nanotubes (CNT) composite powders were prepared by spray drying and ball milling, followed by plasma spraying to fabricate coatings. The effect of CNT content on microstructure and wear resistance was investigated. The powders showed uniform size and high sphericity. Coatings mainly consisted of α-Al₂O₃, γ-Al₂O₃, and TiO₂. CNT addition refined grain size to 18.3 ± 1.1 nm. The high thermal conductivity of CNT reduced unmelted particles, improving coating density and element uniformity. Average coating thickness was 200 μm. When the CNT content reached 3 wt.%, the coating porosity decreased to 5.01 ± 0.72%. TEM analysis indicated that CeO₂ was mainly located at the grain boundaries. Moreover, the interfaces between CNT (002) and CeO₂ (220) appeared clean and well-bonded. As CNT content increased, microhardness and wear resistance first increased then decreased. At 3 wt.% CNT, the volumetric wear rate was 0.87 ± 0.15 × 10⁻⁵ mm³·N⁻¹·m⁻¹, representing an 8.46-times improvement in wear resistance compared to the substrate. The presence of CeO₂ enhanced the surface activity of CNT, facilitating the formation of lubricating films during friction and contributing to the superior wear resistance of the composite coating. Full article

In this study, we investigated how co-solvent and polymer combinations affect the performance of dye-sensitized solar cells (DSSCs) using TiO₂- and ZnO-modified carbon nanotube (CNT) composite papers as photoelectrodes. Co-solvents such as N,N-dimethylformamide (DMF) and ethylene glycol (EG) were incorporated into polyethylene glycol (PEG)- and poly(ethylene oxide) (PEO)-based gel electrolytes to increase the amount of dissolved I₂/KI redox species and evaluate their influence on the wettability of the electrolyte on CNT composite paper electrodes. PEG-based electrolytes containing DMF or EG improved the fill factor (FF) and power conversion efficiency (PCE) relative to the baseline formulation, with the EG–PEG electrolyte achieving the best single-device PCE of 15.58 × 10⁻³% using the CNT/ZnO composite paper. Replacing PEG with PEO or using PEG + PEO blends led to reduced performance, possibly because the modified polymer composition affected electrolyte wetting, spreading behavior, and penetration into the porous electrode. These results suggest that the wettability and viscosity-related behavior of gel electrolytes are important empirical factors associated with the performance of flexible paper DSSCs, and provide practical guidance for the design of paper-based photovoltaic devices. Full article

In this study, TiO₂ nanotube (TNTs) array electrodes were fabricated by electrochemical anodization and subsequently modified through thermal annealing, hydrogenation heat treatment, and chemical decoration with copper species at various immersion times to enhance their electrochemical performance. The structural, morphological, semiconducting, and electrochemical properties of the modified nanotubes were systematically examined. FE-SEM and EDS analyses confirmed the formation of well-aligned TNTs and the successful deposition of copper species, with the most uniform surface distribution achieved for the sample decorated for 45 min. Raman spectroscopy and XRD results revealed that the anatase phase of TiO₂ remained stable after hydrogenation and copper decoration, while minor peak shifts indicated defect evolution and lattice distortion. Electrochemical evaluations, including linear sweep voltammetry, Tafel polarization, electrochemical impedance spectroscopy, and Mott–Schottky analysis, demonstrated a substantial enhancement in electrocatalytic activity following copper decoration. Compared with annealed and hydrogenated electrodes, the decorated samples exhibited markedly lower overpotentials, reduced cathodic Tafel slopes, and decreased charge-transfer resistance. Mott–Schottky analysis confirmed n-type semiconducting behavior for all electrodes, showing that hydrogenation increased donor density, whereas subsequent copper decoration slightly reduced it due to the partial substitution of oxygen vacancies by copper oxide species. Among all samples, the electrode decorated for 45 min (AA′HD45) exhibited the optimal balance between donor density, charge-transfer properties, and electrochemical performance. These results highlight the effectiveness of combining hydrogenation with optimized copper decoration to improve charge transport and interfacial kinetics in TNT electrodes for electrochemical applications. Full article

Dye-sensitized solar cells (DSSCs) remain attractive as low-cost photovoltaic devices; however, their practical efficiency is still constrained by electron-transport losses, interfacial recombination, and incomplete light harvesting in conventional titanium dioxide (TiO₂) photoanodes. The effects of TiO₂ film thickness, multi-walled carbon nanotube (MWCNT) incorporation, and multilayer oxide interface engineering on DSSC performance were examined. Degussa P25-TiO₂ photoanodes were first optimized with respect to thickness, after which controlled MWCNT loadings and sequential compact sol–gel TiO₂ and tin dioxide (SnO₂) sublayers were introduced. The optimum pristine P25-TiO₂ photoanode thickness was 9.11 μm, yielding an open-circuit voltage of 0.74 ± 0.01 V, a short-circuit current density of 14.10 ± 0.40 mA/cm², a fill factor of 56.24 ± 1.00%, and a power-conversion efficiency of 5.93 ± 0.20%. The incorporation of 0.025 wt% MWCNTs increased the efficiency to 6.04 ± 0.20%, corresponding to an absolute gain of 0.11 percentage points. The best performance was obtained with the sol–gel SnO₂/sol–gel TiO₂/P25-CNT multilayer photoanode, which delivered 0.74 ± 0.02 V, 16.22 ± 0.40 mA/cm², 57.59 ± 1.00%, and 6.89 ± 0.30%, respectively. FE-SEM, EIS, XRD, Heated Ultrasonic Cleaner and UV–visible analyses indicate that the multilayer architecture preserves porosity, enhances light harvesting, and suppresses interfacial recombination, while the CNT network facilitates charge transport. Full article

A nanostructured sensing platform based on electrospun functionalized multi-walled carbon nanotubes/poly(3-aminobenzylamine) (FMWCNTs/P3ABA) was developed for the electrochemical detection of dopamine (DA) on fluorine-doped tin oxide (FTO) glass substrate. The electrochemical characteristics of the electrodes were investigated by chronocoulometry (CC) and cyclic voltammetry (CV) in phosphate-buffered saline solution containing K₃[Fe(CN)₆] as a redox mediator. The zeta potential analysis confirmed the presence of a stable surface charge that favors electrostatic interaction with DA molecules. The DA detection was performed in human urine by differential pulse voltammetry (DPV) over a potential of −0.2 to 0.8 V and at scan rate of 5 mV s⁻¹, where the FMWCNTs/P3ABA nanofiber electrode exhibited a high sensitivity of 1.502 µA cm⁻² nM⁻¹, a linear detection range of 10–500 nM (R² = 0.992), and a limit of detection of 1.753 nM. The sensor exhibited stable and reproducible responses, and the fibrous composite effectively discriminated DA from common electroactive interferents, including ascorbic acid, uric acid, creatinine, and glucose. Furthermore, reliable dopamine quantification in human urine samples demonstrates the strong potential of the electrospun FMWCNTs/P3ABA composite nanofiber platform for practical bioanalytical and non-invasive sensing applications in the future. Full article

We report a versatile, CMOS-compatible fabrication module for sub-100 nm TiN and TaN pillar electrodes, a key building block for sandwich-type test structures. As a demonstration, the electrodes were integrated into carbon nanotube-based nonvolatile random-access memory (CRAM) test structures. High-resolution hydrogen silsesquioxane (HSQ) masks defined by electron beam lithography were transferred into TiN films using optimized Ar/Cl₂ inductively coupled plasma reactive ion etching. Optical emission spectroscopy was used for real-time endpoint detection, ensuring precise etch control. The process achieved a TiN-to-HSQ selectivity of ~1.6 and reproducible nanoscale features with smooth sidewalls and an average taper angle of ~77°. Buffered hydrogen fluoride treatment effectively removed residual HSQ, revealing sharp TiN features and preserving pillar geometry. Atomic force microscopy (AFM) confirmed pillar height and profile fidelity, while conductive AFM verified electrical conductivity after planarization. The module was further demonstrated through the fabrication of TiN pillar arrays, TaN pillars, and sub-100 nm TiN line arrays. A CRAM test structure incorporating TiN pillars exhibited preliminary switching, indicating that both the test structure and fabrication process are feasible. This fabrication module provides a reproducible platform for nanoscale TiN and TaN electrodes, supporting laboratory-scale research and providing a pathway toward future integration of emerging memory and nanoelectronic technologies. Full article

Transparent conductive materials (TCMs) are essential for optoelectrical devices ranging from smart windows and defogging films to soft sensors, display technologies, and flexible electronics. Materials, such as indium tin oxide (ITO) and silver nanowires (AgNWs), are commonly used and offer high optical transmittance and electrical conductivity, but suffer from brittleness, oxidation susceptibility, and require high-cost materials, greatly limiting their use. Carbon nanotube (CNT) networks provide a promising alternative, featuring mechanical compliance, chemical robustness, and scalable processing. This study reports an aqueous ink formulation composed of ultra-long mix-walled carbon nanotubes (UL-CNTs), compatible with the flow coating process, yielding uniform transparent conductive films (TCFs) on polyethylene terephthalate (PET), glass, and polycarbonate (PC). The resulting films exhibit tunable transmittance (85%–88% for single layers; ~57% for three layers at 550 nm) and sheet resistance of 7.5 kΩ/□ to 1.5 kΩ/□ accordingly. These TCFs maintain stable sheet resistance for over 5000 bending cycles and show excellent mechanical durability with negligible effects on heating performance. Post-deposition treatments, including nitric acid vapor doping or flash photonic heating (FPH), further reduce sheet resistance by up to 80% (7.5 kΩ/□ to 1.2 kΩ/□). X-ray photoelectron spectroscopy (XPS) results in reduced surface oxygen content after FPH. The photonic-treated heaters attain ~100 °C within 20 s at 100 V. This scalable, water-based process provides a pathway toward low-cost, flexible, and stretchable devices in a variety of fields, including printed electronics, optoelectronics, and thermal actuators. Full article

Developing photoelectrochemical systems that couple pollutant removal with resource recovery is of great significance for sustainable wastewater treatment. In this study, a dual-function photocatalytic fuel cell (PFC) was developed using a TiO₂ nanotube photoanode modified with an amorphous CoOx cocatalyst, which markedly enhances charge separation and interfacial reaction kinetics. The optimized TiO₂@CoOx electrode achieves a twofold enhancement in photocurrent compared to pristine TiO₂. When applied to Cu²⁺-containing wastewater, the PFC achieved 91% Cu²⁺ removal under N₂-purged conditions, with metallic Cu identified as the sole reduction product. Although dissolved oxygen reduced metal recovery efficiency through competitive electron consumption, it simultaneously increased power generation and improved anodic organic degradation. Overall, the results demonstrate that amorphous-CoOx-modified TiO₂ photoanodes offer an effective platform for integrating sustainable energy production with wastewater remediation and valuable copper recovery. Full article

The application of bioinspired nanocomposites in orthopedic implants marks a significant innovation in biomedical engineering, aimed at overcoming long-standing limitations of conventional implant materials. Traditional implants frequently suffer from poor osseointegration, mechanical mismatch with bone, and vulnerability to infection. Bioinspired nanocomposites, modeled after the hierarchical structures found in natural tissues such as bone and nacre, offer the potential to enhance mechanical performance, biological compatibility, and implant functionality. This study reviews and synthesizes current advancements in the design, fabrication, and functionalization of bioinspired nanocomposite materials for orthopedic use. Emphasis is placed on the integration of nanocrystalline hydroxyapatite (nHA), carbon nanotubes (CNTs), titanium dioxide (TiO₂) nanotubes, and other nanostructured coatings that mimic the extracellular matrix. Methods include comparative evaluations of mechanical properties, surface modifications for biocompatibility, and analyses of antibacterial efficacy through nano-topographical features. Bioinspired nanocomposites have been shown to improve osteoblast adhesion, proliferation, and differentiation, thereby enhancing osseointegration. Nanostructured coatings such as TiO₂ nanotubes increase surface hydrophilicity and corrosion resistance, supporting long-term implant stability. Mechanically, these composites offer high stiffness, superior wear resistance, and improved strength-to-weight ratios. Biomimetic combinations of hydroxyapatite, zirconia, and biopolymers have demonstrated effective load transfer and reduced stress shielding. Additionally, antibacterial functionality has been achieved via nanostructured surfaces that deter bacterial adhesion while remaining cytocompatible with host tissues. The integration of bioinspired nanocomposites into orthopedic implants provides a multifunctional platform for enhancing clinical outcomes. These materials not only replicate the mechanical and biological properties of native bone but also introduce new capabilities such as infection resistance and stimuli-responsive behavior. Despite these advancements, challenges including manufacturing scalability, long-term durability, and regulatory compliance remain. Continued interdisciplinary research is essential for translating these innovations from laboratory to clinical practice. Full article

This paper reports an assessment of the photocatalytic activity of TiO₂ nanotubes (TNTs) doped with strontium titanate (SrTiO₃) and sulfur (S) with respect to the decomposition of methylene blue (MB). TNT was obtained by the double anodizing method with further doping of strontium titanate by the hydrothermal method and additional annealing in an atmosphere of N₂ (95%) + H₂S (5%) at 450–550 °C. The photocatalytic activity was evaluated using MB as a pollutant and this study was conducted using an Osram Vita-Lux lamp with a power of 300W as a visible light source. The photocatalytic abilities of the synthesized materials were investigated, and characterized by methods such as SEM, TEM, XRD, EDS, and UV–Vis spectroscopy. Our study showed that the SrTiO₃/TiO₂NT@S composite has a better photocatalytic decomposition ability for the dye under consideration compared to pure TNT and SrTiO₃/TiO₂NT. These results clearly demonstrate the potential of synthesized SrTiO₃/TiO₂NT@S material for applications in water purification and photocatalysis. Full article

Carbon nanotube (CNT) coatings show excellent tribological properties but face challenges in dispersion and industrial application. This study investigated TiO₂ nanoparticle incorporation effects on CNT coating tribological performance. CNT/TiO₂ composite coatings with varying TiO₂ content (0.5–2.0 wt.%) were fabricated on SUS 304 substrates via spin coating. Surface morphology, roughness, wettability, and tribological properties were characterized using confocal microscopy, SEM, Raman spectroscopy, and reciprocating friction tests. Results showed that low TiO₂ concentrations (0.5–0.7 wt.%) achieved optimal performance. The C3-Ti0.5 specimen maintained substrate-level smoothness (Ra = 0.09 μm) while preserving coating integrity. Raman analysis confirmed structural preservation of CNTs (ID/IG ≈ 1.0) across all formulations. Tribologically, C3-Ti0.5 exhibited a friction coefficient of 0.099, approaching pure CNT coating performance (0.090), with a wear rate of 9.00 × 10⁻⁷ mm³/N·mm. Higher TiO₂ concentrations progressively degraded performance, with C3-Ti2 showing increased friction (0.263) and wear rate (2.87 × 10⁻⁶ mm³/N·mm). The 0.5–0.7 wt.% TiO₂ range represents optimal composition for applications requiring both smooth surface finish and superior tribological performance, particularly for precision mechanical components where surface quality and friction control are equally critical. Full article

Graphene-based nanomaterials, including graphene oxide (GO) and graphene quantum dots (GQDs), exhibit exceptional properties, which might facilitate the functional modification of TiO₂ nanotubes (NTs) for enhanced rapid osseointegration. This study investigated the effects of GO/GQD-deposited TiO₂-NTs on cell proliferation, osteogenic differentiation of rat bone marrow-derived mesenchymal stem cells (BMSCs), and early osseointegration in male 6-week-old Sprague Dawley (SD) rats. TiO₂-NTs (control group) were fabricated on titanium substrates via anodic oxidation. GO and GQDs were electrochemically deposited onto the TiO₂-NTs using cyclic voltammetry with 0.5 mg/mL GO and 0.1 mg/mL GQD dispersions to form NT-GO and NT-GQDs. In vitro assays evaluated cell adhesion, proliferation, and osteogenic differentiation. Implants were randomly inserted into one femoral epiphysis of nine rats (n = 3), and osseointegration was evaluated using micro-computed tomography and sequential fluorescence labeling at 2, 4, and 6 weeks post-implantation. Statistical analysis was conducted using ANOVA. Cyclic voltammetry successfully synthesized NT-GO and NT-GQDs, with Raman spectra confirming D and G bands. Both NT-GO and NT-GQDs exhibited superior cell adhesion, proliferation, and enhanced osteogenic differentiation compared with TiO₂-NTs. Notably, the NT-GQDs significantly promoted new bone formation in vivo. The integration of graphene nanomaterials onto TiO₂-NTs improves biocompatibility and accelerates osteogenesis, suggesting a promising strategy for enhancing osseointegration in orthopedic and dental implants. Full article

Tin(IV) oxide (SnO₂) was deposited onto acid-washed multiwalled carbon nanotubes (MWCNTs) to be used as a support for platinum nanoparticles (PtNPs). The effect of the SnO₂–CNT support on the electrocatalytic activity of the PtNPs for the oxygen reduction reaction (ORR) in 0.1 M HClO₄ solution was investigated. The physical characterization of the catalyst confirms the presence of Pt, Sn and C on the catalyst as well as the presence of the PtNPs on SnO₂. The synthesized catalyst possesses a specific activity of 0.15 mA cm⁻² at 0.9 V, while the commercial Pt/C catalyst showed a specific activity of 0.05 mA cm⁻². Accelerated durability testing (ADT) was performed on both catalysts, with the synthesized PtNP/SnO₂–CNT catalyst retaining over 50% of its initial electrochemically active surface area (ECSA). Thus, the results obtained in this study confirm the positive influence of SnO₂-decorated CNTs on the overall electrocatalytic activity of PtNPs and their stability toward the ORR. Full article

Primary hip and knee arthroplasties are common surgeries in the U.S., with periprosthetic joint infection (PJI) being the leading cause of implant revision. Systemic antibiotics often fail to achieve sufficient local concentrations, driving interest in localized drug delivery. Titanium (Ti) implants modified with titania nanotubes (TNTs) provide an increased surface area for drug loading and controlled release. Previous studies have shown that gentamicin-loaded TNTs inhibit Staphylococcus aureus growth in vitro without compromising osteoblast viability. This study investigated the effect of gentamicin–chitosan (GC)-coated TNT implants in a murine model, hypothesizing a positive impact on osseointegration. Titanium alloy (Ti6Al4V) wires were anodized to form TNTs and then coated with gentamicin–chitosan (GC) via electrophoretic deposition. Implants (Bare, TNT, TNT+GC; n = 30) were inserted bilaterally into femoral canals of C57BL/6J mice. After > 1 month, osseointegration was assessed by histological point counting, scanning electron microscopy (SEM)-based areal analysis, and mechanical pull-out testing. ANOVA was used to identify differences between groups, and linear regression was applied to account for harvest time, bone contact area, and anatomical section. Bone area fraction (BAF) around the implant measured by the SEM–areal method was significantly higher around TNT+GC (18.4% ± 1.1) and TNT (16.5% ± 1.4) versus Bare (9.0% ± 2.3) (p < 0.0028) implants. The maximum fixation strength was higher for TNT (0.878 ± 0.175 N/mm²) and TNT+GC (0.853 ± 0.215N/mm²) when compared to bare implants 0.316 ± 0.082 N/mm²) (p = 0.048 and p = 0.050, respectively). No significant differences appeared between TNT and TNT+GC. These findings indicate that GC coatings on TNT implants do not impair osseointegration and may even enhance bone–implant integration. Such coatings may therefore provide dual benefits, offering antibacterial protection while improving bone fixation, making them a promising strategy for PJI prevention. Further long-term studies are needed to confirm durability and clinical translation. Full article