Search Results (15)

The thermoluminescence (TL) method is one of the most widely used techniques in various studies, including dosimetric applications, dating of archaeological and geological materials, luminescence spectroscopy of certain insulating or semiconducting phosphors, and the detection of ionizing radiation damage. This study examines the TL properties of plagioclase, a feldspar group mineral, focusing on its dose–response behavior, kinetic parameters, and glow curve characteristics. TL measurements of plagioclase samples were carried out with different ionizing radiation doses ranging from 0.1 to 550 Gy. The results show a strong linear dose–response relationship in the 0.3–550 Gy range, with no evidence of saturation or supralinearity. A computerized glow curve deconvolution (CGCD) analysis revealed that the TL glow curve of the mineral consists of five distinct TL peaks with activation energies ranging from 0.842 eV to 0.890 eV and obeying general order kinetics. In addition, an artificial neural network (ANN) model was developed to predict TL glow curves using three optimization algorithms, including Levenberg–Marquardt (LM), Bayesian Regularization (BR), and Scaled Conjugate Gradient (SCG). Among these, the BR algorithm demonstrated the best performance with an accuracy value of 0.99915, a Mean Absolute Error (MAE) of 2.34 × 10⁻³, and a Mean Squared Error (MSE) of 3.82 × 10⁻⁵, outperforming LM and SCG in in terms of generalization and accuracy. The findings of this study demonstrate the effectiveness of combining TL analysis with ANN-based modelling for accurate dose–response predictions and the improved luminescence characterization of plagioclase, supporting the applications of luminescence studies in radiation dosimetry and geochronology. Full article

We investigated the thermoluminescence (TL) properties of Mn-doped zinc zirconate (ZnZrO₃:Mn) phosphors under beta (β) radiation. SEM revealed morphological changes with varying levels of Mn doping (0–5%), while XRD confirmed a pure cubic phase. Mn doping introduced luminescent centers, enhancing emission efficiency. Mn²⁺ ions facilitated green/red emissions (⁴T₁ → ⁶A₁), while Mn⁴⁺ contributed to deep-red emissions (²E → ⁴A₂), making the material suitable for optoelectronic applications. Compared to conventional phosphors, ZnZrO₃:Mn exhibited superior thermal stability, enhanced luminescence, and tunable emissions. The TL dose−response showed a systematic peak shift to higher temperatures with increasing radiation dose, confirming its potential for use in accurate dosimetry. The TL glow curves displayed primary (349 K) and secondary (473 K) peaks that were influenced by heating-rate variations, which led to peak shifts and increased intensity. An innovative thermal-cleaning approach (110–336 °C) refined luminescence by stabilizing deeper traps while erasing shallow-trap signals. This combined effect of Mn doping and thermal treatment optimized ZnZrO₃ phosphors’ structural, optical, and TL properties. These findings provide insights into their potential use in radiation dosimetry and display technologies, offering a new strategy for future perspective luminescent materials Full article

The morphological, structural, and thermoluminescence (TL) properties of LiF:SiO₅ doped with Ce³⁺ solid powder phosphor were systematically analyzed. X-ray diffraction (XRD) confirmed the crystalline nature of single-phase LiF:SiO₅:Ce³⁺ nanoparticles (NPs), with crystalline size (D) determined using the Williamson–Hall (W–H) and Scherrer methods. Ce³⁺ doping induced structural modifications, reflected in variations of full width at half maximum (FWHM), strain, and stress values. The TL glow curve revealed two distinct peaks at approximately 64 °C and 134 °C, shedding light on the electron capture and release mechanisms following beta irradiation. A dose-dependent study demonstrated that TL intensity increased proportionally with radiation exposure, showing a superlinearity relationship up to 6 Gy. Additionally, investigations into different heating rates indicated only a slight shift in peak of the temperature, confirming the thermal stability of the materials. This study provides valuable insights into the TL behavior of LiF:SiO₅:Ce³⁺, making it a promising candidate for radiation dosimetry and luminescence applications. Full article

The axion anti-quark nugget (A$\overline{\mathrm{Q}}$N) model was developed to explain in a natural way the asymmetry between matter and antimatter in Universe. In this hypothesis, a similitude between the dark and the visible components exists. The lack of observability of any type of dark matter up to now, in particular A$\overline{\mathrm{Q}}$Ns, requires finding new ways of detecting these particles, if they exist. In spite of strong interaction with visible matter, for such objects a very small ratio of cross section to mass is expected and thus huge detector systems are necessary. This paper presents a new idea for the direct detection of the A$\overline{\mathrm{Q}}$Ns using minerals as natural rock deposits acting as paleo-detectors, where the latent signals of luminescence produced by interactions of A$\overline{\mathrm{Q}}$Ns are registered and can be identified as an increased and symmetrical deposited dose. The estimates were made for minerals widely distributed on Earth, for which the thermoluminescence (TL) signal is intense and if the thermal conditions are constant and with low temperatures, the lifetime of the latent signals is kept for geological time scales. Full article

Thermoluminescent dosimeters (TLD) and optically stimulated luminescent dosimeters (OSLD) are practical, accurate, and precise tools for point dosimetry in medical physics applications. The objective of this study is to investigate the luminescence properties—both OSL and TL—of lithium fluoride (LiF) doped with magnesium (Mg), copper (Cu), and phosphorous (P) (LiF: Mg, Cu, P), commercially known as TLD-100H. The goal is to devise a methodological approach for dose measurement that allows for obtaining two independently measured dose values at each irradiation point, thereby improving accuracy and precision. The luminescence properties of TLD-100H were studied using a beta irradiation source (90Sr/90Y) integrated into the TL/OSL DA-15 automated Risø reader. This study identified the ideal experimental conditions for optimal dose evaluation and used them for dosimeter calibration across doses ranging from 0.5 to 4.0 Gy. The results demonstrated that, under optimal measurement parameters, the OSL and residual thermoluminescence (ResTL) signals—correlated to two trap systems within the dosimeter—exhibited high reproducibility, stability over multiple cycles, and high precision and accuracy (≤2%). Specifically, the OSL response showed good linear behavior across the investigated dose range, while the ResTL signal exhibited linear behavior between 0.5 and 2 Gy and sublinear behavior for doses >2 Gy. Full article

Objective: This study aims to establish a local diagnostic reference level (LDRL) for single-photon emission tomography/computed tomography (SPECT/CT) and positron emission tomography/CT (PET/CT) with respect to myocardial perfusion imaging (MPI). Materials and Methods: The acquisition protocol and dosimetry data on the MPI procedures of five SPECT/CT scans and one PET/CT scan were collected. Data on technitum-99m sestamibi (^99mTc-sestamibi), ^99mTc-tetrofosmin, thallium-201 (²⁰¹Tl), and rubidium-82 (⁸²RB) were all collected from one centre via questionnaire booklets. Descriptive data analysis was used to analyse all variables, and the 50th percentile was used to analyse each radiation dose quantity. Results: The reported 50th percentile dose for a one-day stress/rest protocol using ^99mTc-sestamibi (445/1147 MBq) and ^99mTc-tetrofosmin (445/1147 MBq) and for a two-day stress/rest protocol using ^99mTc-sestamibi (1165/1184 MBq) and ^99mTc-tetrofosmin (1221/1184 MBq) are in good agreement with reported national diagnostic reference levels (NDRLs). However, the dose from the study data on a one-day stress/rest protocol using ^99mTc-sestamibi was more than the 50th percentile dose from the Brazilian data (370/1110 MBq) on a similar protocol, and the dose from the study data on a two-day stress/rest protocol using ^99mTc-tetrofosmin was more than the 50th percentile dose (1084/1110 MBq) from the United States data on MPI scans. Regarding the computed tomography (CT) portion of the SPECT/CT framework, the 50th percentile doses were lower than all the identified doses in the data considered in the literature reviewed. However, regarding the CT component of the PET/CT MPI scans, the ⁸²RB dose was more than the recorded doses in the CT data in the published literature. Conclusion: This study determined the LDRL of five SPECT/CT protocols and one PET/CT MPI protocol. The results suggest that there may be opportunities to optimise the patient radiation burden from administered activities in patients undergoing SPECT examinations and the CT components associated with ⁸²RB PET/CT scans without compromising diagnostic image quality. Full article

The production of thermoluminescence (TL) dosimeters fabricated from B₂O₃-CaF₂-Al₂O₃-SiO₂ doped with Cu and Pr for use in diagnostic radiology is the main goal of this research. The TL samples were synthesized via the melt-quench technique processed by melting the mixture at 1200 °C for 1 h, and, after cooling, the sample thus created was divided into two samples and retreated by heating for 2 h (referred to as TLV30) and for 15 h (referred to as TLV17). SEM and EDS analyses were performed on the TL samples to confirm the preparation process and to investigate the effects of irradiation dosimetry on the TL samples. Furthermore, the TL samples were irradiated with γ-rays using a 450 Ci ¹³⁷Cs irradiator and variable X-ray beams (5–70 mGy). Two important diagnostic radiology applications were considered: CT (6–24 mGy) and mammography (2.72–10.8 mGy). Important dosimetric properties, such as the glow curves, reproducibility, dose–response linearity, energy dependence, minimum dose detectability and fading, were investigated for the synthetized samples (TLV17 and TLV30), the results of which were compared with the Harshaw TLD-100. The TLV17 dosimeter showed higher sensitivity than TLV30 in all applied irradiation procedures. The dose–response linearity coefficients of determination R² for TLV17 were higher than TLD-100 and TLV30 in some applications and were almost equal in others. The reproducibility results of TLV17, TLV30 and TLD-100 were less than 5%, which is acceptable. On the other hand, the results of the fading investigations showed that, in general, TLV17 showed less fading than TLV30. Both samples showed a significant decrease in this regard after the first day, and then the signal variation became essentially stable though with a slight decrease until the eighth day. Therefore, it is recommended to read the TL dosimeters after 24 h, as with TLD-100. The SEM images confirmed the existence of crystallization, whilst the EDS spectra confirmed the presence of the elements used for preparation. Furthermore, we noticed that TLV17 had grown dense crystals that were larger in size compared to those of TLV30, which explains the higher sensitivity in TLV17. Overall, despite the fading, TLV17 showed greater radiation sensitivity and dose–response linearity compared with TLD-100. The synthetized TL samples showed their suitability for use as dosimeters in diagnostic radiology radiation dosimetry. Full article

[²¹²Pb]VMT01 is a melanocortin 1 receptor (MC1R) targeted theranostic ligand in clinical development for alpha particle therapy for melanoma. ²¹²Pb has an elementally matched gamma-emitting isotope ²⁰³Pb; thus, [²⁰³Pb]VMT01 can be used as an imaging surrogate for [²¹²Pb]VMT01. [²¹²Pb]VMT01 human serum stability studies have demonstrated retention of the ²¹²Bi daughter within the chelator following beta emission of parent ²¹²Pb. However, the subsequent alpha emission from the decay of ²¹²Bi into ²⁰⁸Tl results in the generation of free ²⁰⁸Tl. Due to the 10.64-hour half-life of ²¹²Pb, accumulation of free ²⁰⁸Tl in the injectate will occur. The goal of this work is to estimate the human dosimetry for [²¹²Pb]VMT01 and the impact of free ²⁰⁸Tl in the injectate on human tissue absorbed doses. Human [²¹²Pb]VMT01 tissue absorbed doses were estimated from murine [²⁰³Pb]VMT01 biodistribution data, and human biodistribution values for ²⁰¹Tl chloride (a cardiac imaging agent) from published data were used to estimate the dosimetry of free ²⁰⁸Tl. Results indicate that the dose-limiting tissues for [²¹²Pb]VMT01 are the red marrow and the kidneys, with estimated absorbed doses of 1.06 and 8.27 mGy_{RBE = 5}/MBq. The estimated percent increase in absorbed doses from free ²⁰⁸Tl in the injectate is 0.03% and 0.09% to the red marrow and the kidneys, respectively. Absorbed doses from free ²⁰⁸Tl result in a percent increase of no more than 1.2% over [²¹²Pb]VMT01 in any organ or tissue. This latter finding indicates that free ²⁰⁸Tl in the [²¹²Pb]VMT01 injectate will not substantially impact estimated tissue absorbed doses in humans. Full article

This work examined the thermoluminescence dosimetry characteristics of Ag-doped ZnO thin films. The hydrothermal method was employed to synthesize Ag-doped ZnO thin films with variant molarity of Ag (0, 0.5, 1.0, 3.0, and 5.0 mol%). The structure, morphology, and optical characteristics were investigated using X-ray diffraction (XRD), scanning electron microscope (SEM), energy-dispersive X-ray spectroscopy (EDX), photoluminescence (PL), and UV–vis spectrophotometers. The thermoluminescence characteristics were examined by exposing the samples to X-ray radiation. It was obtained that the highest TL intensity for Ag-doped ZnO thin films appeared to correspond to 0.5 mol% of Ag, when the films were exposed to X-ray radiation. The results further showed that the glow curve has a single peak at 240–325 °C, with its maximum at 270 °C, which corresponded to the heating rate of 5 °C/s. The results of the annealing procedures showed the best TL response was found at 400 °C and 30 min. The dose–response revealed a good linear up to 4 Gy. The proposed sensitivity was 1.8 times higher than the TLD 100 chips. The thermal fading was recorded at 8% for 1 Gy and 20% for 4 Gy in the first hour. After 45 days of irradiation, the signal loss was recorded at 32% and 40% for the cases of 1 Gy and 4 Gy, respectively. The obtained optical fading results confirmed that all samples’ stored signals were affected by the exposure to sunlight, which decreased up to 70% after 6 h. This new dosimeter exhibits good properties for radiation measurement, given its overgrowth (in terms of the glow curve) within 30 s (similar to the TLD 100 case), simple annealing procedure, and high sensitivity (two times that of the TLD 100). Full article

A sensitization procedure is used to enhance the thermoluminescence (TL) sensitivity of phyllite to emit radiation. Phyllite is a type of foliated metamorphic rock made from slate. This study examines naturally grown phyllite rock, which had not been previously studied. Using a Thermo 3500 manual reader, the TL sensitivity of phyllite as a function of dosage was measured. The doses required to perform this study were administered using a ⁶⁰Co source. The statistical regression test of the data had a significance level of p < 0.05. The study also included thermal and pre-dose effects. Using the sensitization procedure, the nonlinearity in TL dose–response was removed, and the sensitivity was increased 44 times that of its original value. The fading study showed a dependence on the test dose. According to the obtained results, the combination of linear dose–response and high sensitivity to gamma radiation makes phyllite an important rock for dating and retrospective dosimetry. Full article

Different types of ceramics and glass have been extensively investigated due to their application in brachytherapy, radiotherapy, nuclear medicine diagnosis, radioisotope power systems, radiation processing of food, geological and archaeological dating methods. This review collects the newest experimental results on the thermoluminescent (TL) properties of crystalline and glassy materials. The comparison of the physico-chemical properties shows that glassy materials could be a promising alternative for dosimetry purposes. Furthermore, the controlled process of crystallization can enhance the thermoluminescent properties of glasses. On the other hand, the article presents information on the ranges of the linear response to the dose of ionizing radiation and on the temperature positions of the thermoluminescent peaks depending on the doping concentration with rare-earth elements for crystalline and glassy materials. Additionally, the stability of dosimetric information storage (fading) and the optimal concentration of admixtures that cause the highest thermoluminescent response for a given type of the material are characterized. The influence of modifiers addition, i.e., rare-earth elements on the spectral properties of borate and phosphate glasses is described. Full article

In microCT imaging, there is a close relationship between the dose of radiation absorbed by animals and the image quality, or spatial resolution. Although the radiation levels used in these systems are generally non-lethal, they can induce cellular or molecular alterations that affect the experimental results. Here, we describe a dosimetric characterization of the different image acquisition modalities used by the microCT unit of the Albira microPET/SPECT/CT scanner, which is a widely used multimodal imaging system in preclinical research. The imparted dose at the animal surface (IDS) was estimated based on Boone’s polynomial interpolation method and experimental measurements using an ionization chamber and thermoluminescent dosimeters. The results indicated that the imparted dose at surface level delivered to the mice was in the 30 to 300 mGy range. For any combination of current (0.2 or 0.4 mA) and voltage (35 or 45 kV), in the Standard, Good, and Best image acquisition modalities, the dose imparted at surface level in rodents was below its threshold of deterministic effects (250 mGy); however, the High Res modality was above that threshold. Full article

The phosphate glass samples doped with Tb₂O₃ oxide (general formula: P₂O₅-Al₂O₃-Na₂O-Tb₂O₃) were synthesized and studied for usage in high-dose radiation dosimetry (for example, in high-activity nuclear waste disposals). The influence of terbium concentration on thermoluminescent (TL) signals was analyzed. TL properties of glasses were investigated using various experimental techniques such as direct measurements of TL response vs. radiation dose, T_max–T_stop and VHR (various heating rate) methods, and glow curve deconvolution analysis. The thermoluminescence dosimetry (TLD) technique was used as the main investigation tool to study detectors’ dose responses. It has been proved that increasing the concentration of terbium oxide in glass matrices significantly increases the thermoluminescence yield of examined material. For the highest dose range (up to 35 kGy), the dependence of the integrated thermoluminescent signals vs. dose can be considered as a saturation-type curve. Additional preheating of samples improves linearity of signal vs. dose dependencies and leads to a decrease of the signal loss over time. All obtained data suggest that investigated material can be used in high-dose radiation dosimetry. Additional advantages of the investigated dosimetric system are its potential ability to re-use the same dosimeters multiple times and the fact that reading dosimeters only requires usage of a basic TL reader without any modifications. Full article

In this work, structural and thermoluminescence (TL) characteristics for ZnB₂O₄:xTb³⁺ (x = 0.01, 0.02, 0.03, 0.04, 0.05, and 0.10 mole) phosphors were investigated. The phosphors were prepared via synthesis of nitric acid. The X-ray diffraction (XRD) studies show that the synthesized samples can be indexed to nearly single-phase cubic ZnB₂O₄. The TL characteristics following ⁹⁰Sr beta irradiation (40 mCi) were studied. TL intensity is found to depend on Tb concentration. The optimal concentration of the doped Tb³⁺ is 0.03 mol in TL measurements. TL dose responses of the phosphors to beta doses of 0.143, 0.715, 1.43, 15, 30 and 60 Gy showed fairly linear behavior. The minimum detectable dose (MDD) value for ZnB₂O₄:0.04Tb³⁺ was found to be 87 mGy. The kinetic parameters of the ZnB₂O₄:0.03Tb³⁺ sample were estimated by the glow curve deconvolution, the initial rise, the curve fitting, and the peak shape methods. The results indicate that these phosphors are thought to be promising candidates as TL materials. The results provide valuable knowledge of the characteristics of Tb-doped ZnB₂O₄ for use in dosimetry research. Full article

In this work we report on the thermoluminescence (TL) and optically stimulated luminescence (OSL) properties of β-Na(Gd,Lu)F₄:Tb³⁺ nanophosphors prepared via a standard high-temperature coprecipitation route. Irradiating this phosphor with X-rays not only produces radioluminescence but also leads to a bright green afterglow that is detectable up to hours after excitation has stopped. The storage capacity of the phosphor was found to be (2.83 ± 0.05) × 10¹⁶ photons/gram, which is extraordinarily high for nano-sized particles and comparable to the benchmark bulk phosphor SrAl₂O₄:Eu²⁺,Dy³⁺. By combining TL with OSL, we show that the relatively shallow traps, which dominate the TL glow curves and are responsible for the bright afterglow, can also be emptied optically using 808 or 980 nm infrared light while the deeper traps can only be emptied thermally. This OSL at therapeutically relevant radiation doses is of high interest to the medical dosimetry community, and is demonstrated here in uniform, solution-processable nanocrystals. Full article