Search Results (11)

Optical oxygen sensors have attracted considerable attention owing to their high sensitivity, rapid response, and broad applicability. However, their test results may be affected by fluctuations in the pump light source and instability of the detection equipment. In this study, the intrinsic luminescence of pine wood was utilized as the reference signal, and the luminescence of platinum(II) octaethylporphyrin (PtOEP) was employed as the oxygen indication signal, to fabricate a dual-signal ratiometric oxygen sensor PtOEP/PDMS@Pine. The ratio of the luminescence of pine wood to that of PtOEP was defined as the optical parameter (OP). OP increased linearly with oxygen concentration ([O₂]) in the range of 10–100 kPa, and a calibration curve was obtained. The sensor exhibits excellent anti-interference capabilities, effectively resisting fluctuations from laser sources and detection equipment. It also displays stable hydrophobicity with a contact angle of 118.3° and maintains excellent photostability under continuous illumination. The sensor exhibited long-term stability within 90 days and robust recovery performance during cyclic tests, wherein the response time and recovery time were determined to be 1.4 s and 1.7 s, respectively. Finally, the effects of temperature fluctuations and photobleaching on the sensor’s performance have been effectively corrected, enabling accurate oxygen concentration measurements in complex environments. Full article

This study utilized tetramethylammonium hydroxide (TMAH) as a substitute for traditional catalysts and successfully incorporated platinum octaethylporphyrin (PtOEP) into SiO₂ nanoparticles (PtOEP@SiO₂) via the Stöber method. Methyl silicone resin was employed as the matrix material, and a drop-coating technique was applied to fabricate thin films of PtOEP@SiO₂ particles for dissolved oxygen (DO) sensing in seawater. By optimizing the concentrations of TMAH and PtOEP, a highly sensitive oxygen-sensing film with a quenching ratio (I₀/I₁₀₀) of 28 was ultimately developed, with a wide linear detection range (0~20 mg/L, R² = 0.994). Stability tests revealed no significant performance degradation during five oxygen–nitrogen cycle tests. After 30 days of immersion in East China Sea seawater, the quenching ratio decreased by only 6%, confirming its long-term stability and excellent resistance to ion interference. This research provides a novel strategy for developing highly reliable in situ marine DO sensors. Full article

In this study, an approach has been proposed in response to the urgent need for a sensitive and stable method for glucose detection at low concentrations. Platinum octaethylporphyrin (PtOEP) was chosen as the probe and embedded into the matrix material to yield a glucose-sensing film, i.e., Pt/TE-MTS, through a sol–gel process. The optical parameter (OP) was defined as the ratio of phosphorescence in the absence and presence of glucose, and the relationship between OP and glucose concentration (GC) was established in a theoretical way based on the Stern–Volmer equation and further obtained by photoluminescence measurement. OP exhibited a linear relationship with GC in a range of 0–720 μM. The time required by the photoluminescence of the film to reach equilibrium was measured to ensure the completion of the reaction, and it was found that the equilibrium time decreased as the GC increased. The photobleaching behavior and stabilization of the film were monitored, and the result showed that the film exhibited excellent resistance to photobleaching and was quite stable in an aqueous solution. Additionally, a LabVIEW-based GC-detection system was developed to achieve the practical application of the sensing film. In summary, the Pt/TE-MTS film exhibited high sensitivity in detecting the GC with excellent reproducibility, which is of high value in applications. Full article

Sensitivity is one of the crucial factors in determining the quality of a fluorescence/phosphorescence-based gas sensor, and is estimated from the measurement of responses (I₀/I, where I₀ and I refer to the measured optical intensity of a sensor in absence and presence of analyte molecules) at various concentrations of analytes. In this work, we demonstrate phosphorescence-based optical oxygen sensors fabricated on highly porous anodic aluminum oxide (AAO) membranes showing dramatically high response. These sensors exploit the enormous surface area of the AAO to facilitate the effective interaction between the sensing molecules and the analytes. We spin-coat an AAO membrane (200 nm pore diameter) with a platinum-based oxygen sensing porphyrin dye, platinum(II) meso-tetrakis (pentafluorophenyl) porphyrin (PtTFPP), to fabricate a sensor exhibiting I₀/I ~400 at 100% oxygen atmosphere. To address the generality of the AAO membrane, we fabricate a separate sensor with another porphyrin dye, platinum octaethylporphyrin (PtOEP), which exhibits an even higher I₀/I of ~500. Both of these sensors offer the highest responses as an optical oxygen sensor hitherto reported. SEM and EDS analysis are performed to realize the effect of the increased surface area of the AAO membrane on the enhanced sensitivity. Full article

Triplet-triplet annihilation upconversion (TTA-UC) nanoparticles (NPs) have emerged as imaging probes and therapeutic probes in recent years due to their excellent optical properties. In contrast to lanthanide ion-doped inorganic materials, highly efficient TTA-UC can be generated by low excitation power density, which makes it suitable for clinical applications. In the present study, we used biodegradable poly(lactic-co-glycolic acid) (PLGA)-NPs as a delivery vehicle for TTA-UC based on the heavy metal porphyrin Platinum(II) octaethylporphyrin (PtOEP) and the polycyclic aromatic hydrocarbon 9,10-diphenylanthracene (DPA) as a photosensitizer/emitter pair. TTA-UC-PLGA-NPs were successfully synthesized according to an oil-in-water emulsion and solvent evaporation method. After physicochemical characterization, UC-efficacy of TTA-UC-PLGA-NPs was assessed in vitro and ex vivo. TTA-UC could be detected in the tumour area 96 h after in vivo administration of TTA-UC-PLGA-NPs, confirming the integrity and suitability of PLGA-NPs as a TTA-UC in vivo delivery system. Thus, this study provides proof-of-concept that the advantageous properties of PLGA can be combined with the unique optical properties of TTA-UC for the development of advanced nanocarriers for simultaneous in vivo molecular imaging and drug delivery. Full article

The advanced and widespread use of microfluidic devices, which are usually fabricated in polydimethylsiloxane (PDMS), requires the integration of many sensors, always compatible with microfluidic fabrication processes. Moreover, current limitations of the existing optical and electrochemical oxygen sensors regarding long-term stability due to sensor degradation, biofouling, fabrication processes and cost have led to the development of new approaches. Thus, this manuscript reports the development, fabrication and characterization of a low-cost and highly sensitive dissolved oxygen optical sensor based on a membrane of PDMS doped with platinum octaethylporphyrin (PtOEP) film, fabricated using standard microfluidic materials and processes. The excellent mechanical and chemical properties (high permeability to oxygen, anti-biofouling characteristics) of PDMS result in membranes with superior sensitivity compared with other matrix materials. The wide use of PtOEP in sensing applications, due to its advantage of being easily synthesized using microtechnologies, its strong phosphorescence at room temperature with a quantum yield close to 50%, its excellent Strokes Shift as well as its relatively long lifetime (75 µs), provide the suitable conditions for the development of a miniaturized luminescence optical oxygen sensor allowing long-term applications. The influence of the PDMS film thickness (0.1–2.5 mm) and the PtOEP concentration (363, 545, 727 ppm) in luminescent properties are presented. This enables to achieve low detection levels in a gas media range from 0.5% up to 20%, and in liquid media from 0.5 mg/L up to 3.3 mg/L at 1 atm, 25 °C. As a result, we propose a simple and cost-effective system based on a LED membrane photodiode system to detect low oxygen concentrations for in situ applications. Full article

We present an all-polymer optical fiber sensor for the sensing of dissolved oxygen by phase-fluorometry. The sensing matrix is applied as a film on the fiber end-surface, and consists of poly-methylmethacrylate (PMMA), the oxygen quenchable luminophore platinum-octaethylporphyrin (PtOEP) and the luminophore coumarin 545T for increasing the brightness of PtOEP by way of resonance energy transfer (RET), also called light harvesting. We show that by using Hansen Solubility Parameters (HSPs), it is possible to quantitatively formulate a solvent mixture with a good solubility of the polymer matrix and the luminophores simultaneously. Our approach can readily be extended to other polymers and luminophores and is therefore a valuable tool for researchers working with photoluminescence and polymeric matrices. Full article

The large-scale production of plastic and the resulting release of waste is leading to a huge accumulation of micro-sized particles in the environment that could have an impact on not only aquatic organisms but also on humans. Despite the extensive literature on the subject, there is still an insufficient harmonization of methodologies for the collection and analysis of microplastics (MPs) in complex matrices; especially for high density polymers; such as polyvinyl chloride (PVC), which tend to sink and accumulate in sediments, becoming available to benthonic organisms. In this article, mussels have been chosen as model for microplastic accumulation due to their extensive filtering activity and their wide distribution in both fresh and salt water basins. To facilitate the identification and quantification of microplastics taken up by mussels, novel fluorescent and metal-doped PVC microplastics (PVC-Platinum octaethylporphyrin (PtOEP) MPs in the size range of 100 µm) have been synthesized and characterized. For the analysis of the mussels following exposure, an enzymatic protocol using amylase, lipase, papain, and SDS for organic material digestion and a sucrose-ZnCl₂ density gradient for the selective separation of ingested microplastics has been developed. The final identification of MPs was performed by fluorescence microscopy. This work can greatly benefit the scientific community by providing a means to study the behavior of PVC MPs, which represent an example of a very relevant yet poorly studied high density polymeric contaminant commonly found in complex environmental matrices. Full article

A ratiometric oxygen sensor based on a platinum octaethylporphyrin (PtOEP)–coumarin 6 (C6)/poly (styrene-trifluoroethyl methacrylate) (poly (St-TFEMA)) film was developed for automatic dissolved oxygen (DO) detection. The oxygen-sensing film according to the dynamic quenching mechanism was prepared by embedding platinum octaethylporphyrin (PtOEP) and coumarin 6 (C6) in poly (styrene-trifluoroethyl methacrylate) (poly (St-TFEMA)). The optical parameter (OP) was defined as the ratio of the oxygen-insensitive fluorescence from C6 to the oxygen-sensitive phosphorescence from PtOEP. A calibration equation expressing the correlation between the OP values and DO content described by a linear function was obtained. A program based on the Labview software was developed for monitoring the real-time DO content automatically. The influence of the excitation intensity and fluctuation on the OP values and the direct luminescence signal (integration areas) was compared, verifying the strong anti-interference ability of the sensor. The detection limit of the sensor was determined to be 0.10 (1) mg/L. The switching response time and recovery time of the sensor were 0.4 and 1.3 s, respectively. Finally, the oxygen sensor was applied to the investigation of the kinetic process of the DO content variation, which revealed an exponential relationship with time. Full article

This paper presents a simple, high resolution imaging approach utilizing ratiometric planar optode for simultaneous measurement of dissolved oxygen (DO) and pH. The planar optode comprises a plastic optical film coated with oxygen indicator Platinum(II) octaethylporphyrin (PtOEP) and reference quantum dots (QDs) embedded in polystyrene (PS), pH indicator 5-Hexadecanoylamino-fluorescein (5-Fluorescein) embedded in Hydromed D4 matrix. The indicator and reference dyes are excited by utilizing an LED (Light Emitting Diode) source with a central wavelength of 405 nm, the emission respectively matches the different channels (red, green, and blue) of a 3CCD camera after eliminating the excitation source by utilizing the color filter. The result shows that there is low cross-sensitivity between the two analytes dissolved oxygen and pH, and it shows good performance in the dynamic response ranges of 0–12 mg/L and a dynamic range of pH 6−8. The optode has been tested with regard to the response times, accuracy, photostability and stability. The applied experiment for detecting pH/Oxygen of sea-water under the influence of the rain drops is demonstrated. It is shown that the planar optode measuring system provides a simple method with low cross-talk for pH/Oxygen imaging in aqueous applications. Full article

We have proposed a novel concept of a pressure sensor called electroluminescent pressure sensor (ELPS) based on oxygen quenching of electroluminescence. The sensor was fabricated as an organic light-emitting device (OLED) with phosphorescent dyes whose phosphorescence can be quenched by oxygenmolecules, and with a polymer electrode which permeates oxygen molecules. The sensor was a single-layer OLED with Platinum (II) octaethylporphine (PtOEP) doped into poly(vinylcarbazole) (PVK) as an oxygen sensitive emissive layer and poly(3,4-ethylenedioxythiophene) mixed with poly(styrenesulfonate) (PEDOT:PSS) as an oxygen permeating polymer anode. The pressure sensitivity of the fabricated ELPS sample was equivalent to that of the sensor excited by an illumination light source. Moreover, the pressure sensitivity of the sensor is equivalent to that of conventional pressure-sensitive paint (PSP), which is an optical pressure sensor based on photoluminescence. Full article