Search Results (121)

Despite extensive research on blast-resistant concrete structures, a clear scientific deficiency remains in the quantitative understanding of how fiber-reinforced concrete slabs behave under blast loading, particularly when experimental and numerical investigations are not conducted together under identical loading conditions. Existing studies often focus on either conventional reinforced concrete or isolated material systems, providing limited validation of comparative blast performance across different fiber-reinforced concretes. This study addresses this gap by investigating the blast resistance performance of four types of reinforced concrete slabs: normal concrete (NC), ultra-high-performance fiber-reinforced concrete (UHPFRC), organic fiber-reinforced high-performance concrete (O-HPC), and basalt FRP-sheet-strengthened slurry-infiltrated fiber concrete (F-SIFCON), using full-scale blast experiments and validated numerical simulations conducted with ANSYS Explicit Dynamics. Blast tests were performed to obtain time histories of reflected pressure, displacement, acceleration, reaction force, and internal energy. The influence of different fiber systems and FRP strengthening on dynamic response and failure mechanisms was systematically analyzed. The numerical models showed good agreement with experimental measurements, confirming their reliability. The results indicate that the normal concrete slab exhibited brittle failure and poor blast resistance, whereas the F-SIFCON slab demonstrated the best overall performance. Compared with the normal concrete slab, the F-SIFCON slab achieved approximately a 47% reduction in maximum displacement, a 56% increase in peak reaction force, and the highest internal energy absorption of 236 kJ. The UHPFRC and O-HPC slabs also showed improved blast resistance, although with different post-peak response characteristics. These findings demonstrate that hybrid fiber reinforcement combined with FRP strengthening can significantly enhance the blast resistance of concrete slabs and that coupled experimental–numerical approaches provide a robust framework for evaluating structural performance under extreme dynamic loading. Full article

Façades account for approximately 15–20% of a building’s embodied carbon, making them a key target for material decarbonization. While bio-composites are increasingly explored for façade insulation, cladding systems remain dominated by carbon-intensive materials such as aluminum and fiber-reinforced polymers (FRPs). This paper presents findings from a study investigating the use of food-waste-derived bulk fillers in bio-composite materials for façade cladding applications. Several food-waste streams, including hazelnut and pistachio shells, date seeds, avocado and mango pits, tea leaves, and brewing waste, were processed into fine powders (<0.125 μm) and combined with a furan-based biobased thermoset resin to produce flat composite sheets. The samples were evaluated through mechanical testing (flexural strength, stiffness, and impact resistance), water absorption, freeze–thaw durability, and optical microscopy to assess microstructural characteristics before and after testing. The results reveal substantial performance differences between waste streams. In particular, hazelnut and pistachio shell fillers produced bio-composites suitable for façade cladding, achieving flexural strengths of 62.6 MPa and 53.6 MPa and impact strengths of 3.42 kJ/m² and 1.39 kJ/m², respectively. These findings demonstrate the potential of food-waste-based bio-composites as low-carbon façade cladding materials and highlight future opportunities for optimization of processing, supply chains, and material design. Full article

The one-step hybrid forming process is a novel process to fabricate a metal fiber-reinforced plastic (FRP) structure with reduced cycle time and cost compared to classical multi-step methods. It is realized by a combined forming tool for both sheet metal and FRP forming to create a hybrid part in only one step. During the forming process, sheet metal pre-coated with an adhesion promoter is joined with the FRP simultaneously. In this work, the crashworthiness and lightweight potential of a hybrid crash management system manufactured with a hybrid forming process were investigated. It includes the experimental behaviors and finite element analysis of glass mat thermoplastics (GMT), as well as aluminum–GMT hybrid structures, under dynamic axial crushing loadings. Beginning with the original geometry of a series aluminum crash management system, the design was optimized for a hybrid forming process, where an aluminum sheet metal part is reinforced by a GMT structure with a ground layer and additional ribs. The forming behavior and fiber filling of the GMT crash box were determined and analyzed as well. Finite element method optimization was used to obtain the optimal geometry of the hybrid crash box with the highest possible specific energy absorption and the utmost homogeneous force level over displacement. A hybrid bumper beam was also developed, along with other necessary connection parts, to join the beam with the crash box and the entire crash management system (CMS) to the vehicle body. The joining technique was determined to be a key factor restricting the lightweight potential of the hybrid CMS. Full article

In recent years, the demand for high-strength concrete (HSC) for buildings has been steadily increasing. Continuous HSC deep beams are frequently employed in various structural applications, including high-rise buildings, bridges, and parking garages, due to their superior load capacity. Some cases require the addition of openings after the construction for passing utilities such as drainage and electricity. This study experimentally examines four two-span HSC deep beams: one control solid beam, one beam with circular openings, and two beams that utilized different strengthening schemes. The openings were asymmetrical circular openings, with one positioned in each span. This study sought to regain the full capacity of beams with openings by employing two types of strengthening schemes. The first one used bolted steel plates, while the second was a hybrid scheme that combined bolted steel plates with externally bonded fiber-reinforced polymer (FRP) sheets. Test findings demonstrated that both methods effectively restored the load capacity of the strengthened beams. The strengthened beam with steel plates achieved a load capacity of 125% compared to the solid beam. Likewise, the beam retrofitted with hybrid steel/FRP composites reached 117%. Additionally, the energy dissipation and ductility index of the strengthened beam with steel plates were 32% and 77%, respectively, compared to the strengthened beam with hybrid steel/FRP composites. The findings emphasize the effectiveness of the applied retrofitting techniques in restoring the lost capacity due to the cutting of post-construction openings in deep beams. Full article

This research presents an experimental investigation on the compressive behavior of fiber reinforced polymer-confined concrete-filled steel tubes (FRP-CFSTs). The study evaluated 72 specimens, including CFST and FRP-CFST columns, with varying numbers of FRP layer (0–3), steel tube thickness (1.8 to 3.8 mm), and nominal concrete strength (20, 30, 40 MPa). Concrete mixes enhanced with polypropylene fibers and silica fume were used. Material properties for the infill concrete, steel tube yield strength (307 MPa), and CFRP tensile parameters (ultimate strain 2.1%, tensile strength 4900 MPa) were determined. The test specimens were wrapped with CFRP sheets using a wet lay-up process and subjected to axial compression through a 4000-kN capacity machine. The load–deformation behavior until failure, which typically occurred due to FRP rupture from lateral concrete expansion, was recorded. Results revealed that FRP confinement increased the ultimate axial load capacity of CFST columns and enhanced ductility with improvements correlating positively with the number of CFRP layers. Steel tube thickness contributed to an increase in stiffness and load capacity by roughly 15–25%. Concrete mixes incorporating polypropylene fibers and silica fume demonstrated superior performance compared to conventional mixes by reducing brittleness and improving tensile and flexural strengths. These quantitative findings demonstrate the significant influence of FRP confinement and concrete mix design on the enhancing strength, stiffness, and ductility of CFST columns, supported by rigorous experimental characterization and systematic analysis of their composite behavior. Full article

Dams are currently confronted with severe risks from frequent extreme climates and expanding aging deterioration, with traditional mitigation measures struggling to balance efficient prevention/control and long-term management. As an innovative solution, fiber-reinforced polymer (FRP) composites support improved dam safety governance. To address the lack of systematic integration in existing dam-related studies, this paper promotes the development of an FRP in the dam field by comprehensively analyzing and summarizing the material properties, interfacial bonding properties of the FRP, as well as the flexural and compressive characteristics of FRP bar–concrete members and FRP sheet–concrete members while systematically organizing their practical engineering application cases. It also explores the FRP’s potential in hydraulic structures and suggests its wider application therein based on the FRP’s superior properties. Full article

Lightweight Aggregate Reinforced Concrete (LWARC) is increasingly used in structural systems to reduce dead load, especially in flat slabs. This study focuses on LWARC-incorporating polystyrene foam as a partial aggregate replacement, achieving a dry unit weight reduction from 23.0 kN/m³ to 19.0 kN/m³. While beneficial for lowering dead loads, this substitution exacerbates punching shear vulnerability, necessitating innovative strengthening solutions. Fiber-Reinforced Polymers (FRPs), recognized for their high strength-to-weight ratio, corrosion resistance, and adaptability, are employed to address these limitations. This paper evaluates the punching shear strengthening of LWARC flat slabs using externally bonded carbon fiber-reinforced polymer (CFRP) sheets, embedded through-section (ETS) steel bars, and ETS glass fiber-reinforced polymer (GFRP) bars. Ten specimens were tested under concentric loading, including an unstrengthened control slab. Experimental results were compared with predictions from ECP 203-2023, ACI 318-19, and BS 8110 to assess code applicability. Strengthened specimens demonstrated significant improvements in punching capacity and ductility. The ETS steel bar technique increased punching strength by 41% compared to the control, while inclined reinforcement configurations outperformed vertical layouts by 24% due to optimized shear transfer. Full article

This study presents a high-performance external strengthening strategy for reinforced concrete (RC) beam–column joints, integrating near-surface mounted (NSM) Carbon Fiber Reinforced Polymer (C-FRP) ropes with externally bonded C-FRP sheets. The X-shaped ropes, anchored diagonally on both principal joint faces and complemented by vertical ropes at column corners, provide enhanced core confinement and shear reinforcement. C-FRP sheets applied to the beam’s plastic hinge region further increase flexural strength and delay localized failure. Three full-scale, shear-deficient RC joints were subjected to cyclic lateral loading. The unstrengthened specimen (JB0V) exhibited rapid stiffness deterioration, premature joint shear cracking, and unstable hysteretic behavior. In contrast, the specimen strengthened solely with X-shaped C-FRP ropes (JB0VF2X2c) displayed a markedly slower rate of stiffness degradation, delayed crack development, and improved energy dissipation stability. The fully retrofitted specimen (JB0VF2X2c + C-FRP) demonstrated the most pronounced gains, with peak load capacity increased by 65%, equivalent viscous damping enhanced by 55%, and joint shear deformations reduced by more than 40%. Even at 4% drift, it retained over 90% of its peak strength, while localizing damage away from the joint core—a performance unattainable by the unstrengthened configuration. These results clearly establish that the combined C-FRP rope–sheet system transforms the seismic response of deficient RC joints, offering a lightweight, non-invasive, and rapidly deployable retrofit solution. By simultaneously boosting shear resistance, ductility, and energy dissipation while controlling damage localization, the technique provides a robust pathway to extend service life and significantly enhance post-earthquake functionality in critical structural connections. Full article

Traditional fiber-reinforced polymer (FRP) retrofit methods can restore the strength of reinforced concrete columns well, but stiffness is also partly restored. To increase the initial stiffness of retrofitted columns, this study investigated the seismic behavior of retrofitted resilient reinforced concrete (RRC) columns that were retrofitted by different methods, including high-strength mortar retrofit, carbon fiber-reinforced polymer (CFRP) retrofit, and CFRP and steel plate retrofit. In addition, the effect of the axial load was also considered. Quasi-static tests were conducted twice on five specimens, i.e., before and after repairing. The first test was used to create earthquake damage, and the second test was used to compare the seismic behavior of the retrofitted columns. The experimental results indicated that the CFRP retrofit method, whether with a steel plate or not, can restore the lateral resistance capacity well; furthermore, the drift-hardening behavior and self-centering performance were well maintained. The residual drift ratio of the CFRP-retrofitted column was less than 0.5%, even at a drift ratio of 3.5%, and less than 1% at the 6% drift ratio. However, the initial stiffness was only partly restored using the CFRP sheet. The introduction of steel plates was beneficial in restoring the initial stiffness, and the stiffness recovery rate remained above 90% when CFRP sheets and steel plates were used simultaneously. The strain distribution of the CFRP sheet showed that the steel plate did work at the initial loading stage, but the effect was limited. By using the steel plate, the CFRP hoop strain on the south side was reduced by 68% at the 6% drift ratio in the push direction and 38% in the pull direction. The axial strain of CFRP cannot be ignored due to the larger value than the hoop strain, which means that the biaxial stress condition should be considered when using an FRP sheet to retrofit RC columns. Full article

Accurate prediction of fiber-reinforced polymer (FRP)-concrete interfacial bond strength is critical for ensuring the safety of FRP-strengthened structures. This study proposes a predictive model based on extreme gradient boosting (XGBoost), which is enhanced via the Nevergrad optimization framework, to address the limited accuracy of traditional empirical approaches. By integrating seven optimizers from the Nevergrad platform, the model achieves global hyperparameter optimization, and a five-fold cross-validation strategy is employed to improve generalization. The prediction results based on 855 sets of single-lap shear test data demonstrate that the optimized model exhibits significantly superior performance on the test set (R² = 0.9726, RMSE = 1.8745, MAE = 1.3857). Compared to the existing best-performing empirical model, the R² is improved by 22.3%, while the RMSE and MAE are reduced by 63.4% and 61.8%, respectively. SHAP interpretability analysis indicates that the width, thickness, elastic modulus, and bond length of the FRP sheets are the main factors influencing the bond strength prediction. The predictive model developed in this study combines high accuracy with strong interpretability, providing a reliable, intelligent tool for designing FRP-strengthened structures. Full article

To improve the construction performance of inorganic adhesives used for bonding fiber-reinforced polymer (FRP) sheets to reinforce concrete structures, make rational use of resources, and reduce carbon emissions, double-shear tests on the interface bonding performance between bonded FRP sheets and cement mortar test blocks, as well as four-point bending tests on bonded carbon fiber-reinforced polymers (CFRPs) to reinforce concrete beams, were conducted using basic magnesium sulfate cement (BMSC) as the adhesive. The influence laws of parameters, such as the type of FRP sheet and the number of FRP sheet bonding layers on the shear performance of the bonding interface between BMSC and cement mortar test blocks, were investigated, as well as the influence laws of the number of CFRP sheet bonding layers and the type of binder on the bending performance of CFRP sheet-reinforced beams. The test results show that the ultimate load of CFRP-reinforced beams bonded with BMSC as the binder increased by 17.4% to 44.4% compared with the unreinforced beams and simultaneously improved the flexural stiffness and crack-limiting ability of the reinforced beams. The failure of the reinforced beam begins with the separation of the CFRP sheet from the concrete at the middle and bottom of the beam span. When the CFRP sheet of the reinforced beam is one layer and two layers, the flexural bearing capacity reaches 91.4% and 96%, respectively, of the reinforced beam, with epoxy resin as the binder under the same conditions. With the increase in the number of CFRP layers, the flexural bearing capacity of the reinforced beam improves, but the increased flexural bearing capacity does not increase proportionally with the increase in the number of sheet layers. By introducing the influence coefficient of BMSC on the flexural bearing capacity (FBC) of reinforced beams, based on the test results, the formula for calculating the FBC of concrete beams, which are reinforced with CFRP sheets bonded by BMSC, was developed. After verification, the calculation formulas established in this paper have high accuracy and can provide theoretical references for similar engineering applications. Full article

Currently, there are many infrastructures for which these design service lives are expired. These lifespans have been extended through retrofitting and strengthening. Usually, the existing reinforced concrete (RC) structures are strengthened by applying steel plate bonding and concrete enlargement methods. However, since fiber-reinforced polymer (FRP) composite materials have properties that are better than those of steel and concrete materials, i.e., being light weight, with anticorrosive material, a high ratio of strength to weight, and better workability, FRP sheet bonding methods for RC members have been developed, and practical applications have been gradually increased worldwide, statically. The methods may also have some potential to strengthen the members under impact and blast loading. In this paper, to rationally improve the impact resistance of RC beams under flexure, beams were strengthened by bonding an FRP sheet to the bottom tension side. Then, low-velocity impact loading tests (hereafter referred to as impact loading tests) using a 300 kg steel weight were carried out on the beams strengthened with carbon FRP (CFRP) sheets of different areal masses to investigate the failure mode at the ultimate state of the beams, in which the areal mass is physically similar to the amount of the sheet reinforcing RC beams and hereafter referred to as the sheet volume. Two sheet volumes (one is an areal mass of 300 g/m² having a 0.17 mm thickness and the other is of 600 g/m² having a 0.33 mm thickness) were compared, and two static failure modes, concrete crushing-intermediate crack (IC) debonding and premature IC debonding, were observed. The following results were obtained from this study: taking a static calculated moment ratio M_y/M_u of the rebar yield-moment M_y to the ultimate moment M_u for each beam, in the case of the beams having an M_y/M_u (=0.67) larger than 0.65 that went through static failure in the concrete crushing-IC debonding mode, the beams failed in sheet rupturing mode subjected to an impact load. When the sheet volume was comparatively large and a static calculated moment ratio M_y/M_u (=0.6) was less than 0.65, the beams collapsed in the premature IC debonding mode under not only static but also impact loading, and the impact resistance of the beams was enhanced with an increasing sheet volume; this increase was greater in the impact loading case than in the static loading case. Full article

The inefficiency of unreinforced concrete beams as flexural members poses a challenge because concrete’s tensile strength is significantly lower than its compressive strength. In response to this challenge, reinforcement bars are commonly employed near the tension zone of reinforced concrete (RC) beams. Nonetheless, structures constructed with RC face challenges such as reduced live load capacity, concrete deterioration, and the corrosion of reinforcement bars over time. To address this, ongoing research is exploring maintenance and retrofitting techniques using high-strength, lightweight fiber-reinforced polymer (FRP) composite materials such as carbon fiber-reinforced polymer (CFRP) and glass fiber-reinforced polymer (GFRP). In this study, the flexural performance of corroded RC beams was enhanced through retrofitting with CFRP plates and sheets. The corroded RC beams were fabricated using an applied-current method with a 5% NaCl solution to induce a 10% target corrosion level under controlled laboratory conditions. Flexural tests were conducted to evaluate the structural performance, failure modes, load–displacement relationships, and energy dissipation capacities. The results showed that CFRP reinforcement mitigates the adverse effects of corrosion-induced reduction in rebar cross-sectional areas, leading to increased stiffness and improved load-carrying capacity. In particular, CFRP reinforcement increased the yield load by up to 36.5% and the peak load by up to 90% in corroded specimens. The accumulated energy dissipation capacity also increased by 92%. These enhancements are attributed to the effective load-sharing behavior between the corroded rebar and the CFRP reinforcement. Full article

The push for sustainability in all facets of manufacturing has led to an increased interest in biomass as an alternative to non-renewable materials. Hemp bast fiber mats were produced from a bacterial retting process, named BFM, as the fiber reinforcement. The objective of this study was to evaluate the feasibility of laminating BFM with polylactic acid (PLA) for a composite panel product. Since both BFM and PLA are biodegradable, the resulting BFM-PLA composites will be 100% biodegradable. PLA pallets were processed into thin polymer sheets which served as the matrix. The BFM and PLA plates were laminated in five layers and compression-molded into composite panels. Experiments were conducted on the three BFM-to-PLA ratios (35/65, 45/55, and 50/50). Mechanical properties (tensile and bending properties) and physical properties (thickness swell and water absorption) were tested and compared to the currently commercial sheet molding compound (SMC) from fiber glass. The thermal behavior of the BFM/PLA composites was characterized using dynamic mechanical analysis (DMA) and differential scanning calorimetry (DSC). The developed BFM/PLA composite product is a sustainable alternative to existing synthetical fiber-reinforced polymer (FRP) that is biodegradable in landfill at the end of life. Full article