Search Results (104)

This work investigates resilient control for uncertain nonlinear systems subject to unknown and unpredictable sensor delays. Conventional observer-based delay-compensation methods typically require known delay bounds or measurable timing information, which limits their applicability to strongly nonlinear dynamics. To address this issue, a resilient adaptive fuzzy observer-based sliding control (AFOSMC) framework is developed. A generalized nonlinear plant model is considered, and an adaptive fuzzy observer is constructed to estimate unmeasured states while explicitly decomposing the delayed measurement residual into estimation and delay components. A sliding-mode controller integrated with fuzzy approximation ensures robust tracking in the presence of modeling uncertainties and delay-induced distortions. A delay-dependent Lyapunov function with an integral term is derived, yielding explicit conditions that guarantee uniform ultimate boundedness (UUB) of all closed-loop signals. The proposed approach provides a unified and delay-resilient solution for nonlinear observer–controller co-design under unpredictable sensing delays. Simulations on a Duffing oscillator with a $0.15$ s sensing delay show that the proposed AFOSMC model achieves a total tracking RMSE of $3.6\times {10}^{-2}$, whereas a baseline sliding-mode controller without delay compensation becomes unstable after delay activation. Full article

This study presents a simulation-based framework for PID controller design in strongly nonlinear dynamical systems. The proposed approach avoids system linearization by directly minimizing a performance index using metaheuristic optimization. Three strategies—Particle Swarm Optimization (PSO), Grey Wolf Optimizer (GWO), and their hybrid combination (PSO-GWO)—were evaluated on benchmark systems including pendulum-like, Duffing-type, and nonlinear damping dynamics. The chaotic Duffing oscillator was used as a stringent test for robustness and adaptability. Results indicate that all methods successfully stabilize the systems, while the hybrid PSO-GWO achieves the fastest convergence and requires the fewest cost function evaluations, often less than 10% of standalone methods. Faster convergence may induce aggressive transients, which can be moderated by tuning the ISO (Integral of Squared Overshoot) weighting. Overall, swarm-based PID tuning proves effective and computationally efficient for nonlinear control, offering a robust trade-off between convergence speed, control performance, and algorithmic simplicity. Full article

This study investigates stochastic bifurcation in a generalized tristable Rayleigh–Duffing oscillator with fractional inertial force under both additive and multiplicative recycling noises. The system’s dynamic behavior is influenced by its inherent spatial symmetry, represented by the potential function, as well as by temporal symmetry breaking caused by fractional memory effects and recycling noise. First, an approximate integer-order equivalent system is derived from the original fractional-order model using a harmonic balance method, with minimal mean square error (MSE). The steady-state probability density function (sPDF) of the amplitude is then obtained via stochastic averaging. Using singularity theory, the conditions for stochastic P bifurcation (SPB) are identified. For different fractional derivative’s orders, transition set curves are constructed, and the sPDF is qualitatively analyzed within the regions bounded by these curves—especially under tristable conditions. Theoretical results are validated through Monte Carlo simulations and the Radial Basis Function Neural Network (RBFNN) approach. The findings offer insights for designing fractional-order controllers to improve system response control. Full article

In coal mine non-solidly grounded systems, high-impedance faults generate minimal zero-sequence currents with obscured characteristics and strong interference, complicating faulted line identification. Existing methods rarely address three-phase imbalance and variable cable parameters, causing selection errors. To this end, a method for identifying the non-effective ground fault routing of mining cables based on Steady-State Impedance Analysis (SSIA) and Holmes–Duffing oscillator small-signal detection is proposed. Firstly, based on SSIA, the mapping relationship that the phase of the zero-sequence current variation in the faulted line is the same as the phase of its voltage relative to the faulted ground is derived before and after the occurrence of the fault. Meanwhile, identifiable differences exist in both phase and amplitude of the zero-sequence current change in faulty lines compared to non-faulty lines before and after fault occurrence. This is used as the criterion for high-impedance ground fault line selection. In the mining environment, zero-sequence current variations are characterized as weak signals, which poses significant challenges for detection. Thus, a Holmes–Duffing oscillator weak signal detection method is proposed. Based on chaotic principles, accurate line selection is achieved by diagnosing chaotic states in oscillator-generated phase trajectories. A specific mine grid simulation via MATLAB/Simulink 2023b validates the method’s efficacy and applicability. Full article

Chaotic systems appear in a wide range of natural and engineering contexts, making the design of reliable and flexible control strategies a crucial challenge. This work proposes a robust control scheme based on the Fractional-Order Backstepping Control (FOBC) method for the stabilization of non-commensurate fractional-order chaotic systems subject to bounded uncertainties and external disturbances. The method is developed through a rigorous stability analysis grounded in the Mittag–Leffler function, enabling the step-by-step stabilization of each subsystem. By incorporating fractional-order derivatives into carefully selected Lyapunov candidate functions, the proposed controller ensures global system stability. The performance of the FOBC approach is validated on fractional-order versions of the Duffing–Holmes system and the Rayleigh oscillator, with the results compared against those of a fractional-order PID (FOPID) controller. Numerical evaluations demonstrate the superior performance of the proposed strategy: the error dynamics converge rapidly to zero, the system exhibits strong robustness by restoring state variables to equilibrium quickly after disturbances, and the method achieves low energy dissipation with a high error convergence speed. These quantitative indices confirm the efficiency of FOBC over existing methods. The integration of fractional-order dynamics within the backstepping framework offers a powerful, robust, and resilient approach to stabilizing complex chaotic systems in the presence of uncertainties and external perturbations. Full article

This study investigates the nonlinear dynamics and control of an underactuated hybrid system consisting of a Duffing oscillator, a pendulum, and a piezoelectric energy harvester. A novel Piezoelectric Harvester Proportional–Derivative (PHPD) control scheme is introduced, which integrates the harvester’s electrical output directly into the feedback loop to achieve simultaneous vibration suppression and energy utilization. The nonlinear governing equations are derived and analyzed using the Multiple-Scale Perturbation Technique (MSPT) to obtain reduced-order dynamics. Bifurcation analysis is employed to identify stability boundaries and critical parameter transitions, while numerical simulations based on the fourth-order Runge–Kutta method validate the analytical predictions. Furthermore, frequency response curves (FRCs) and an ideal system are evaluated under multiple controller and system parameter configurations. Bifurcation classification is performed on the analyzed figure to detect various bifurcations within the system, along with the computation of the Largest Lyapunov Exponent (LLE). The results demonstrate that PHPD control significantly reduces vibration amplitude and accelerates convergence, offering a new pathway for energy-efficient, high-performance control in nonlinear electromechanical systems. Full article

Fractional-order models provide a powerful framework for capturing memory-dependent and viscoelastic dynamics in mechanical systems, which are often inadequately represented by classical integer-order characterizations. This study addresses the identification of dynamic parameters in both single-degree-of-freedom (1-DOF) and three-degree-of-freedom (3-DOF) Duffing oscillators with fractional damping, modeled using the Grünwald–Letnikov characterization. The 1-DOF system includes a cubic nonlinear restoring force and is excited by a harmonic input to induce steady-state oscillations. For both systems, time domain simulations are conducted to capture long-term responses, followed by Fourier decomposition to extract steady-state displacement, velocity, and acceleration signals. These components are combined with a GL-based fractional derivative approximation to construct structured regressor matrices. System parameters—including mass, stiffness, damping, and fractional-order effects—are then estimated using pseudoinverse techniques. The identified models are validated through a comparison of reconstructed and original trajectories in the phase space, demonstrating high accuracy in capturing the underlying dynamics. The proposed framework provides a consistent and interpretable approach for frequency domain system identification in fractional-order nonlinear systems, with relevance to applications such as mechanical vibration analysis, structural health monitoring, and smart material modeling. Full article

This study investigates the effect of a nonlinear saturation controller (NSC) on the van der Pol–Mathieu–Duffing oscillator (VMDO). The oscillator is a single degree of freedom (DOF) system. It is driven by an external force. It is described by a nonlinear differential equation (DE). The multiple-scale perturbation method (MSPT) is applied. It gives second-order analytical solutions. The first indirect Lyapunov method is used. It provides the frequency–response equation. It also shows the stability conditions. Internal resonance is included. The analysis considers steady-state responses. It studies simultaneous primary resonance with a 1:2 internal resonance (${\Lambda }_1\cong {\varpi }_1$ and ${\varpi }_1\cong 2{\varpi }_2$). Time–response simulations are presented. They show controlled and uncontrolled systems. Numerical solutions (NSs) are obtained with the fourth-order Runge–Kutta method (RK-4). They are compared with the approximate analytical solution (AS). The agreement is strong. It confirms the perturbation method. It shows that the method captures the main system dynamics. Full article

The growing demand for low-frequency, broadband vibration and noise suppression technologies in next-generation mechanical equipment has become increasingly urgent. Effective negative mass locally resonant structures represent one of the most paradigmatic classes of acoustic metamaterials. Their unique elastic wave bandgaps enable efficient suppression of low-frequency vibrations, while inherent nonlinear effects provide significant potential for the design and tunability of these bandgaps. To achieve ultra-low-frequency and ultra-broadband vibration attenuation, this study employs Duffing oscillators exhibiting negative-stiffness characteristics as structural elements, establishing a bistable nonlinear acoustic-metamaterial mechanical model. Subsequently, based on the effective negative mass local resonance theory, the perturbation solution for the dispersion curves is derived using the perturbation method. Finally, the effects of mass ratio, stiffness ratio, and nonlinear term on the starting and cutoff frequencies of the bandgap are analyzed, and key geometric parameters influencing the design of ultra-low vibration reduction bandgaps are comprehensively investigated. Subsequently, the influence of external excitation amplitude and the nonlinear term on bandgap formation is analyzed using numerical computation methods. Finally, effective positive mass, negative mass, and zero-mass phenomena within distinct frequency ranges of the bandgap and passband are examined to validate the theoretically derived results. The findings demonstrate that, compared to a positive-stiffness system, the bandgap of the bistable nonlinear acoustic metamaterial incorporating negative-stiffness Duffing oscillators shifts to higher frequencies and widens by a factor of $\sqrt{2}$. The external excitation amplitude F changes the bandgap starting frequency and cutoff frequency. As F increases, the starting frequency rises while the cutoff frequency decreases, resulting in a narrowing of the bandgap width. Within the frequency range bounded by the bandgap starting frequency and cutoff frequency, the region between the resonance frequency and cutoff frequency corresponds to an effective negative mass state, whereas the region between the bandgap starting frequency and resonance frequency exhibits an effective positive mass state. Critically, the bandgap encompasses both effective positive mass and negative mass regions, wherein vibration propagation is suppressed. Concurrently, a zero-mass state emerges within this structure, with its frequency precisely coinciding with the bandgap cutoff frequency. This study provides a theoretical foundation and practical guidelines for designing nonlinear acoustic metamaterials targeting ultra-low-frequency and ultra-broadband vibration and noise mitigation. Full article

For systems such as the van der Pol and van der Pol–Duffing oscillators, the study of their oscillation is currently a very active area of research. Many authors have used the bifurcation method to try to determine oscillatory behavior. But when the system involves n separate delays, the equations for bifurcation become quite complex and difficult to deal with. In this paper, the existence of periodic oscillatory behavior was studied for a system consisting of n coupled equations with multiple delays. The method begins by rewriting the second-order system of differential equations as a larger first-order system. Then, the nonlinear system of first-order equations is linearized by disregarding higher-degree terms that are locally small. The instability of the trivial solution to the linearized equations implies the instability of the nonlinear equations. Periodic behavior often occurs when the system is unstable and bounded, so this paper also studied the boundedness here. It follows from previous work on the subject that the conditions here did result in periodic oscillatory behavior, and this is illustrated in the graphs of computer simulations. Full article

The Duffing–van der Pol oscillator is a very prominent and interesting standard model. There is a substantial body of varied literature on this topic. In this article, we propose a new class of oscillators by adding new factors to its dynamics. Investigations in light of Melnikov’s approach are considered. Several simulations are composed. A few specialized modules for testing the dynamics of the hypothetical oscillator under consideration are also given. This will be an essential component of a much broader Web-based scientific computing application that is planned. Possible control over oscillations: approximation with restrictions is also discussed; some probabilistic constructions are also presented. Full article

This paper presents the derivation of an exact solution for a damped nonlinear oscillator of arbitrary order (both integer and non-integer). A coefficient relationship was defined under which such a solution exists. The analytical procedure was developed based on the application of the Ateb (inverse beta) function. It has been shown that an exact solution exists for a specific relationship between the damping coefficient and the coefficient of the linear elastic term, and that this relationship depends on the order of nonlinearity. The exact amplitude of vibration was found to be a time-decreasing function, depending on the initial amplitude, damping coefficient, and the order of nonlinearity. The period of vibration was also shown to depend not only on the amplitude but also on both the nonlinearity coefficient and its order. For cases where the damping coefficient of the exact oscillator is slightly perturbed, an approximate solution based on the exact one was proposed. Three illustrative examples of oscillators with different orders of nonlinearity were considered: a nearly linear oscillator, a Duffing oscillator, and one with strong nonlinearity. For all cases, the high accuracy of the asymptotic solution was confirmed. Since no exact analytic solution exists for a purely nonlinear damped oscillator, an approximate solution was constructed using the solution of the corresponding undamped oscillator with a time-varying amplitude and phase. In the case of a purely cubic damped oscillator, the approximate solution was compared with numerical results, and good agreement was demonstrated. Full article

The 3-dimensional modified van der Pol–Duffing oscillator has been studied by several authors. We complete its study, first characterizing its zero-Hopf equilibria and then its zero-Hopf bifurcations—i.e., we provide sufficient conditions for the existence of three, two or one periodic solutions, bifurcating from the zero-Hopf equilibrium localized at the origin of coordinates. Recall that an equilibrium point of a 3-dimensional differential system whose eigenvalues are zero and a pair of purely imaginary eigenvalues is a zero-Hopf equilibrium. Finally, we determine the dynamics of this system near infinity, i.e., we control the orbits that escape to or come from the infinity. Full article

The literature devoted to the issue of a forced modified Van der Pol–Duffing oscillator with asymmetric potential is a major and varied way to represent nonlinear dissipative chemical dynamics. It is known that this model is based on the real reaction–kinetic scheme. In this paper, we suggest a novel class of oscillators that are appealing to users due to their numerous free parameters and asymmetric potential. The rationale for this is because an expanded model is put out that enables the investigation of both classical and more recent models that have been reported in the literature at a “higher energy level”. We present a few specific modules for examining these oscillators’ behavior. A much broader Web-based application for scientific computing will incorporate this as a key component. Probabilistic construction to offer possible control over the oscillations is also considered. Full article

Solving nonlinear oscillations is challenging, as solutions to the corresponding differential equations do not exist in most cases. Therefore, numerical methods are usually employed to calculate the precise oscillation frequency. In addition, many interesting mathematical approaches leading to approximate solutions have also been developed. This paper focuses on a classic case of a nonlinear oscillator: the oscillator with an odd-power polynomial restoring force. This case encompasses nearly all scenarios of undamped nonlinear oscillations. The idea is to combine two well-known strategies from the literature: He’s approximation, which is simple to apply and valid for small amplitudes, and the analytical solutions for oscillations with power-law restoring forces. It is shown that by combining these approaches, a universal equation accurate for any amplitude is derived. Many tests of the proposed method’s accuracy are presented using polynomials of various degrees and classic examples, such as the rotating pendulum, cubic–quintic Duffing oscillators, and oscillators with cubic and harmonic restoring forces. In addition, a novel ‘electrical analogue’ of the oscillation with a polynomial-type restoring force is introduced to demonstrate that the methods presented in this paper can be applied in real industrial applications. Full article