Search Results (1,491)

Ammonia emissions in poultry houses are common and pose health concerns for animals and workers. However, effective control of these emissions with sustainable products is lacking. Therefore, we investigated if an agricultural byproduct, cottonseed hulls, could be recycled through pyrolysis and used to remove ammonia from air. In this study, the efficacy of ammonia removal was observed using cottonseed hull biomaterials pyrolyzed at seven different temperatures: 250, 300, 350, 400, 500, 600, and 700 °C. In this study, ammonia was passed through a column filled with pyrolyzed material, and ammonia in the filtered air was monitored. The results showed that materials pyrolyzed at intermediate temperatures of 350 and 400 °C were the most efficient at ammonia removal and were able to adsorb approximately 3.7 mg NH₃/g of material. Despite extensive characterization, ammonia adsorption could not be linked to intrinsic material properties. Evaluation of the materials showed that the carbon in the pyrolyzed materials would be stable over time should the spent material be used as a soil amendment. Full article

Brown algae such as Ascophyllum nodosum (AN) and Fucus vesiculosus (FV) are gaining considerable attention as functional feed additives due to their health-beneficial properties. This study evaluated the antioxidant potential of AN and FV extracts in intestinal epithelial cells and the in vivo model Caenorhabditis elegans (C. elegans). Aqueous AN and FV extracts were characterized for total phenolic content (TPC), antioxidant capacity (TEAC, FRAP), and phlorotannin composition using LC-HRMS/MS. Antioxidant effects were assessed in vitro, measuring AAPH-induced ROS production in Caco-2 and IPEC-J2 cells via H₂DCF-DA, and in vivo, evaluating the effects of paraquat-induced oxidative stress and AN or FV treatment on worm motility, GST-4::GFP reporter expression, and gene expression in C. elegans. FV exhibited higher total phenolic content, antioxidant capacity (TEAC, FRAP), and a broader phlorotannin profile (degree of polymerization [DP] 2–9) than AN (DP 2–7), as determined by LC-HRMS/MS. Both extracts attenuated AAPH-induced oxidative stress in epithelial cells, with FV showing greater efficacy. In C. elegans, pre-treatment with AN and FV significantly mitigated a paraquat-induced motility decline by 22% and 11%, respectively, compared to PQ-stressed controls. Under unstressed conditions, both extracts enhanced nematode healthspan, with significant effects observed at 400 µg/g for AN and starting at 100 µg/g for FV. Gene expression analysis indicated that both extracts modulated antioxidant pathways in unstressed worms. Under oxidative stress, pre-treatment with AN and FV significantly reduced GST-4::GFP expression. In the nematode, AN was more protective under acute stress, whereas FV better supported physiological function in the absence of stressors. These findings demonstrate that AN and FV counteract oxidative stress in intestinal epithelial cells and in C. elegans, highlighting their potential as stress-reducing agents in animal feed. Full article

Cutting beech plywood using abrasive water jet (AWJ) technology represents a significant area of research due to increasing demands for precision, quality, and environmental sustainability in manufacturing processes within the woodworking industry. AWJ technology enables non-contact cutting of materials without causing thermal deformation or mechanical damage, which is crucial for preserving the structural integrity and mechanical properties of the plywood. This article investigates cutting beech plywood using technical methods using an abrasive water jet (AWJ) at 400 MPa pressure, with Australian garnet (80 MESH) as the abrasive material. It examines how abrasive mass flow rate, traverse speed, and material thickness affect AWJ lag, which in turn influences both cutting quality and accuracy. Measurements were conducted with power abrasive mass flow rates of 250, 350, and 450 g/min and traverse speeds of 0.2, 0.4, and 0.6 m/min. Results show that increasing the abrasive mass flow rate from 250 g/min to 350 g/min slightly decreased the AWJ cut width by 0.05 mm, while further increasing to 450 g/min caused a slight increase of 0.1 mm. Changes in traverse speed significantly influenced cut width; increasing the traverse speed from 0.2 m/min to 0.4 m/min widened the AWJ by 0.21 mm, while increasing it to 0.6 m/min caused a slight increase of 0.18 mm. For practical applications, it is recommended to use an abrasive mass flow rate of around 350 g/min combined with a traverse speed between 0.2 and 0.4 m/min when cutting beech plywood with AWJ. This balance minimizes jet lag and maintains high surface quality comparable to conventional milling. For thicker plywood, reducing the traverse speed closer to 0.2 m/min and slightly increasing the abrasive flow should ensure clean cuts without compromising surface integrity. Full article

Background: Estimating race times for open-water swimming based on pool swimming times could be useful for talent identification and training optimisation. We aimed to compare the swimming speeds of the world’s top and other swimmers in the 2023 Aquatics Championship men’s 10 km OWS race. Methods: Sixty-five swimmers were divided into four groups: G1 (1st–10th positions), G2 (11st–30th positions), G3 (31st–47th positions), and G4 (48th–65th positions). Swimming speed, stroke frequency (SF), and stroke length (SL) for each lap (laps 1–6) were recorded. Critical speed (CS) was calculated from each participant’s personal best times in the 400, 800, and 1500 m freestyle events in the pool. Swimming speed against CS was calculated (%CS). Results: The top performance group (G1) maintained their swimming speed from beginning (lap 1, 1.53 m/s) to end (lap 6, 1.50 m/s), at 92.7 ± 1.9% of CS, characterised by longer SL (1.26 m) and lower SF (72.86 rpm). G3 and G4 were unable to maintain their swimming speed, which decreased from G3: 97.64 ± 1.62% and G4: 96.10 ± 1.96% of CS at lap 1 to G3: 88.39 ± 3.78% and G4: 85.13 ± 5.04% at lap 6. This reduction in swimming speed is consistent with the increased reliance on anaerobic metabolism reported in previous studies under similar conditions. Conclusions: Race pacing for maintaining speeds of 92%CS throughout the race could be an important resilient index in open-water swimming. %CS might be a useful index for estimating the athletic performance level in open-water swimming. Full article

In this work, biochars were produced by pyrolysis of exhausted olive pomace and evaluated as low-cost adsorbents for the removal of methylene blue (MB) from aqueous solutions. The biochar obtained at 400 °C for 1 h, which exhibited the best adsorption performance, was characterized by FTIR, N₂ adsorption–desorption isotherms, SEM-EDX, and proximate analysis, revealing a mesoporous structure with a relatively low specific surface area but enriched in surface functional groups, likely due to the partial degradation of lignocellulosic components. Adsorption experiments were conducted to optimize operational parameters such as solid particle size (2–3 mm), agitation speed (75 rpm), and bioadsorbent dosage (1 g per 0.05 L of MB solution), which allowed for dye removal efficiencies close to 100%. Kinetic studies showed that MB adsorption followed a pseudo-second-order model, while equilibrium data at 30 °C were best described by the Langmuir isotherm (R² = 0.999; SE = 4.25%), suggesting monolayer coverage and strong adsorbate–adsorbent affinity. Desorption trials using water, ethanol, and their mixtures resulted in low MB recovery, whereas the addition of 10% acetic acid significantly improved desorption performance. Under optimal conditions, up to 52% of the retained dye was recovered. Full article

This study presents the development of Cu-doped NiMo/TiO₂ photoelectrocatalysts for simultaneous green hydrogen production and pharmaceutical pollutant removal under simulated solar irradiation. The catalysts were synthesized via wet impregnation (15 wt.% total metal loading with 0.6 wt.% Cu) and thermally treated at 400 °C and 900 °C to investigate structural transformations and catalytic performance. Comprehensive characterization (XRD, BET, SEM, XPS) revealed phase transitions, enhanced crystallinity, and redistribution of redox states upon Cu incorporation, particularly the formation of NiTiO₃ and an increase in oxygen vacancies. Crystallite sizes for anatase, rutile, and brookite ranged from 21 to 47 nm at NiMoCu400, while NiMoCu900 exhibited only the rutile phase with 55 nm crystallites. BET analysis showed a surface area of 44.4 m²·g⁻¹ for NiMoCu400, and electrochemical measurements confirmed its higher electrochemically active surface area (ECSA, 2.4 cm²), indicating enhanced surface accessibility. In contrast, NiMoCu900 exhibited a much lower BET surface area (1.4 m²·g⁻¹) and ECSA (1.4 cm²), consistent with its inferior photoelectrocatalytic performance. Compared to previously reported binary NiMo/TiO₂ systems, the ternary NiMoCu/TiO₂ catalysts demonstrated significantly improved hydrogen production activity and more efficient photoelectrochemical degradation of paracetamol. Specifically, NiMoCu400 showed an anodic peak current of 0.24 mA·cm⁻² for paracetamol oxidation, representing a 60% increase over NiMo400 and a cathodic current of −0.46 mA·cm⁻² at −0.1 V vs. RHE under illumination, nearly six times higher than the undoped counterpart (–0.08 mA·cm⁻²). Mott–Schottky analysis further revealed that NiMoCu400 retained n-type behavior, while NiMoCu900 exhibited an unusual inversion to p-type, likely due to Cu migration and rutile-phase-induced realignment of donor states. Despite its higher photosensitivity, NiMoCu900 showed negligible photocurrent, confirming that structural preservation and surface redox activity are critical for photoelectrochemical performance. This work provides mechanistic insight into Cu-mediated photoelectrocatalysis and identifies NiMoCu/TiO₂ as a promising bifunctional platform for integrated solar-driven water treatment and sustainable hydrogen production. Full article

This study utilises the Open Source Energy Modelling System (OSeMOSYS) in conjunction with the Climate, Land, Energy, and Water systems (CLEWs) framework to investigate Thailand’s energy transition, which is designed to achieve carbon neutrality by 2050. Two scenarios have been devised to evaluate the long-term trade-offs among energy, water, and land systems. Data were sourced from esteemed international organisations (e.g., the IEA, FAO, and OECD) and national agencies and organised into a tailored OSeMOSYS Starter Data Kit for Thailand, comprising a baseline and a carbon neutral trajectory. The baseline scenario, primarily reliant on fossil fuels, is projected to generate annual CO₂ emissions exceeding 400 million tons and water consumption surpassing 85 billion cubic meters by 2025. By the mid-century, the carbon neutral scenario will have approximately 40% lower water use and a 90% reduction in power sector emissions. Under the carbon neutral path, renewable energy takes the front stage; the share of renewable electricity goes from under 20% in the baseline scenario to almost 80% by 2050. This transition and large reforestation initiatives call for consistent investment in solar energy (solar energy expenditures exceeding 20 billion USD annually by 2025). Still, it provides notable co-benefits, including greater resource sustainability and better alignment with international climate targets. The results provide strategic insights aligned with Thailand’s National Energy Plan (NEP) and offer modelling evidence toward achieving international climate goals under COP29. Full article

In wet flue gas desulfurization and denitrification processes, nitrite accumulation inhibits denitrification efficiency and induces secondary pollution due to its acidic disproportionation. This study developed a Mn-modified ZSM-5 zeolite catalyst, achieving efficient resource conversion of nitrite in nitrogen-containing wastewater through an O₃ + Mn/ZSM-5 catalytic system. Mn/ZSM-5 catalysts with varying SiO₂/Al₂O₃ ratios (prepared by wet impregnation) were characterized by BET, XRD, and XPS. Experimental results demonstrated that Mn/ZSM-5 (SiO₂/Al₂O₃ = 400) exhibited a larger specific surface area, enhanced adsorption capacity, abundant surface Mn³⁺/Mn⁴⁺ species, hydroxyl oxygen species, and chemisorbed oxygen, leading to superior oxidation capability and catalytic activity. Under the optimized conditions of reaction temperature = 40 °C, initial pH = 4, Mn/ZSM-5 dosage = 1 g/L, and O₃ concentration = 100 ppm, the $\mathrm{N}{\mathrm{O}}_2^{-}$ oxidation efficiency reached 94.33%. Repeated tests confirmed that the Mn/ZSM-5 catalyst exhibited excellent stability and wide operational adaptability. The synergistic effect between Mn species and the zeolite support significantly improved ozone utilization efficiency. The O₃ + Mn/ZSM-5 system required less ozone while maintaining high oxidation efficiency, demonstrating better cost-effectiveness. Mechanism studies revealed that the conversion pathway of $\mathrm{N}{\mathrm{O}}_2^{-}$ followed a dual-path catalytic mechanism combining direct ozonation and free radical chain reactions. Practical spray tests confirmed that coupling the Mn/ZSM-5 system with ozone oxidation flue gas denitrification achieved over 95% removal of liquid-phase $\mathrm{N}{\mathrm{O}}_2^{-}$ byproducts without compromising the synergistic removal efficiency of NO_x/SO₂. This study provided an efficient catalytic solution for industrial wastewater treatment and the resource utilization of flue gas denitrification byproducts. Full article

In the present study, for the first time, a biodegradable and non-toxic polyphosphoramidate glycohydrogel (PPAGHGel) was prepared by crosslinking a polyphosphoramidate glycoconjugate (PPAG) with hexamethylene diisocyanate (HMDI) under mild conditions. Poly(oxyethylene H-phosphonate) (POEHP) was used as a precursor and was converted into PPAG via the Staudinger reaction with glucose-containing azide (2-p-azidobenzamide-2-deoxy-1,3,4,6-tetra-O-trimethylsilyl-α-D-glucopyranose). Then, crosslinking of PPAG was performed to yield PPAGHGel, which was thoroughly characterized. The gel showed a gel fraction of 83%, a swelling degree of 1426 ± 98%, and G″ = 1560 ± 65 Pa. The gel was fully degraded by alkaline phosphatase (400 U/L, pH 9) in 19 days, while hydrolytically, up to 52% degradation was observed under similar conditions. Multivalent studies of the obtained hydrogel with lectin–Concanavalin A were performed. PPAGHGel binds 92% of Concanavalin A within 24 h and the complex remains stable until the amount of glucose reaches 0.3 mM. PPAGHGel acts as a stabilizer for silver nanoparticles (12 nm). SEM shows pores measuring 10 µm (surface) and 0.1 mm (interior) with capillary channels, confirming the gel’s suitability for biosensors, drug delivery, or wound dressings. The cytotoxic (IC50) and cell-adhesive properties of the obtained hydrogel were investigated on human cell lines (HeLa). Antibacterial activity tests were also performed with gel containing silver nanoparticles against skin-associated pathogenic bacteria. The results show that PPAGHGel possesses excellent biocompatibility, non-adhesive properties and antibacterial activity. Full article

Covalent triazine frameworks (CTFs) have gained recognition as stable porous organic polymers, for example, for CO₂ separation. From the monomer 4,4′-(phenazine-5,10-diyl)dibenzonitrile (pBN), new pBN-CTFs were synthesized using the ionothermal method with a variation in temperature (400 and 550 °C) and the ZnCl₂-to-monomer ratio (10 and 20). N₂ adsorption yielded BET surface areas up to 1460 m²g ⁻¹. The pBN-CTFs are promising CO₂ adsorbents and are comparable to other benchmark CTFs such as CTF-1 with a CO₂ uptake of pBN-CTF-10-550 at 293 K of up to 54 cm³ g⁻¹ or 96 mg g⁻¹, with a CO₂/CH₄ IAST selectivity of 22 for a 50% mixture of CO₂/CH₄. pBN-CTF-10-400 has a very high heat of adsorption of 79 kJ mol⁻¹ for CO₂ near zero coverage in comparison to other CTFs, and it also stays well above the liquefaction heat of CO₂ due to its high microporosity of 50% of the total pore volume. Full article

Combining potassium-containing rocks with conventional KCl may improve the agronomic use of K rock and reduce leaching from high-soluble sources. The aim of this study was to evaluate K rocks (phonolite and alkaline) and the mixture with KCl at different K rates on the biomass production of maize and rice (residual effect), K uptake, and K leaching. The experiment was conducted in greenhouse columns with sandy soil. The experimental design included four K sources: PR (phonolite rock), PR + KCl in an 86:14 mass ratio, AR (alkaline rock), and KCl; three K rates (100, 200, and 400 mg kg⁻¹); and a control (no K), with five replicates. PR + KCl resulted in similar maize biomass (120 g column⁻¹) and K uptake (18 mg g⁻¹) compared to KCl, and it was higher than the PR, the AR, and the control, which produced 86, 48, and 32 g column⁻¹, respectively. The residual effect of PR, PR + KCl, and KCl generated similar rice biomass. K leaching reached 15% of K applied with KCl and was reduced by 50% with K rocks. Thus, the mixture of PR + KCl can improve K fertilization compared to KCl, enhancing maize and rice biomass while reducing K leaching. Full article

Creole goats have adapted to the harsh Andean environment, yet the physiological impacts of high-altitude production systems remain underexplored. This study assessed seasonal and dietary influences on the hematological and biochemical profiles of 45 Creole goats in the Peruvian Andes. The animals were assigned to three diets: D1 (grazing), D2 (grazing + 2000 g hay), and D3 (grazing + 400 g concentrate), across rainy and dry seasons. Biweekly blood sampling measured urea, cholesterol, total protein, albumin, ALP, ALT, WBCL, NeuP, LymP, HGB, and MCV. Season exerted the strongest influence (p < 0.001), with modest dietary effects and a consistent effect of sampling time. Urea, total protein, and albumin increased during the rainy season, though only urea responded significantly to diet. Leukocytosis rose in the dry season and with higher-protein diets, suggesting heightened immune activation under environmental stress. Hemoglobin peaked in the rainy season and early sampling, indicating better oxygenation. MCV and body weight were higher in the dry season, with weight unaffected by diet. These results underscore the complex interplay of environmental and nutritional factors in shaping goat physiology at high altitudes, emphasizing the importance of dynamic modeling in sustainable Andean livestock systems. Full article

COVID-19 vaccine hesitancy in Pakistan is a barrier to optimal vaccine uptake and has been situated within a context of hesitancy towards other vaccines. A mixed-methods study was conducted during the initial COVID-19 vaccine roll-out in 2021 in four union councils in Peshawar, consisting of a cross-sectional survey, eight focus group discussions (FGDs) with community members and eight in-depth interviews with healthcare workers (HCWs) to assess perceptions toward vaccines. Multivariable logistic regression was used to assess factors associated with COVID-19 vaccine hesitancy. Of 400 survey participants, 57.3% were vaccine acceptant and 42.8% vaccine hesitant. Just over half (56.8%) perceived COVID-19 vaccines to be safe. Most (88%) reported trust in HCWs to provide accurate vaccine information. FGDs revealed that women received less information about the vaccine compared to men and cultural restrictions were barriers even for those willing to be vaccinated. Correlates of vaccine acceptance included male sex (aOR 2.25; 95% CI 1.29–3.91), age 50 years or greater (aOR 1.74; 95% CI 1.19–6.31), social network support (e.g., vaccine acceptance among an individual’s social network) in receiving COVID-19 vaccines (aOR 2.38; 95% CI 1.45–3.89), community concern about COVID-19 spread (aOR 2.84; 95% CI 1.73–4.66), and trust in HCWs to provide vaccine information (aOR 3.47; 95% CI 1.62–7.42). Future vaccine promotion should prioritize engaging community leaders, sharing transparent information, combatting misinformation and rumors, and implementing household-based interventions especially targeting the importance of vaccination among women and young people to increase uptake. Full article

The durability and fire resilience of concrete structures are increasingly critical in modern construction, particularly under elevated-temperature exposure. With this context, the current study explores the thermal and microstructural characteristics of geopolymer-based ultra-high-performance concrete (G-UHPC) incorporating quartz powder (QP) and silica fume (SF) after exposure to elevated temperatures. SF was used at 15% and 30% to partially replace the precursor material, while QP was used at 25%, 30%, and 35% as a partial replacement for fine sand. The prepared specimens were exposed to 200 °C, 400 °C, and 800 °C, followed by air cooling. Mechanical strength tests were conducted to evaluate compressive and flexural strengths, as well as failure patterns. Microstructural changes due to thermal exposure were assessed using scanning electron microscopy (SEM) and energy-dispersive X-ray spectroscopy (EDS). Among the prepared mixtures, the 30SF35QP mixture exhibited the highest compressive strength (156.0 MPa), followed by the 15SF35QP mix (146.83 MPa). The experimental results demonstrated that G-UHPC underwent varying levels of thermal degradation across the 200–800 °C range yet displayed excellent resistance to thermal spalling. At 200 °C, compressive strength increased due to enhanced geopolymerization, with the control mix showing a 29.8% increase. However, significant strength reductions were observed at 800 °C, where the control mix retained only 30.8% (32.0 MPa) and the 30SF25QP mixture retained 28% (38.0 MPa) of their original strengths. Despite increased porosity and cracking at 800 °C, the 30SF35QP mixture exhibited superior strength retention due to its denser matrix and reduced voids. The EDS results confirmed improved gel stability in the 30% SF mixtures, as evidenced by higher silicon content. These findings suggest that optimizing SF and QP content significantly enhances the fire resistance and structural integrity of G-UHPC, providing practical insights for the design of sustainable, high-performance concrete structures in fire-prone environments. Full article

Shrimp farming is practiced worldwide in tropical and subtropical regions, where shrimp often experience suboptimal temperatures during part of the production cycle, resulting in slower growth. A concentrated functional palatability enhancer (FPE) containing a mixture of chemoattractants was tested. A 12-week experiment at a suboptimal temperature (22 °C) was conducted with Penaeus vannamei (3.25 ± 0.02 g) in a clear water system (400 L with 40 shrimp per tank) with flow-through seawater. A standard diet was supplemented with 0, 1, and 2 g kg⁻¹ of FPE (STD, STD+1, and STD+2) with four replicates for each one. The inclusion of 1 g kg⁻¹ of FPE (STD+1) significantly increased the average final weight by 11.24% and weekly weight gain by 14,00% when compared to STD. The highest tested dose (2 g kg⁻¹) did not result in further improvement in growth performance compared to the control. In addition, the total hemocyte count (THC) remained at an optimal level for the species in the STD+1 treatment under suboptimal temperature conditions compared to the other treatments. We also observed a decrease in Vibrio spp. bacterial counts in STD+1 compared to STD+2. Therefore, the lowest tested dose was shown to positively influence the rearing of P. vannamei at suboptimal temperatures. Full article