Search Results (2,071)

To prevent marine biofouling in seawater lift pumps, electrolyzed seawater containing Cu²⁺ needs to be injected into the pumps. This study employs Computational Fluid Dynamics (CFD) to simulate the variation in Cu²⁺ injection concentration required to achieve a Cu²⁺ concentration of 3 ppb within a 10 cm range around the pump under different operating conditions, including the installation of baffles and varying seawater flow rates. The simulation results demonstrate that CFD can accurately predict the distribution of Cu2+ concentration in electrolyzed seawater, with the distribution significantly influenced by seawater flow direction, necessitating reference to upstream data. When the lift pumps are idle, the required Cu²⁺ injection concentration increases with rising seawater flow rates, reaching 41.9 μg/L at the maximum flow rate of 1.9 m/s. During alternating pump operation, the required Cu²⁺ injection concentration also increases with the flow rate, significantly affected by the pump’s operational position: lower concentrations are required when the upstream pump is active compared to the downstream pump. Additionally, installing baffles around the pumps effectively mitigates the impact of seawater flow on Cu²⁺ distribution, significantly reducing the required injection concentration. This study provides theoretical and data-driven insights for optimising marine biofouling prevention in seawater lift pumps. Full article

Cattle manure accounts for approximately one-third of the total livestock manure produced in the Republic of Korea and is typically composted. To elucidate its feasibility as a renewable resource, this study evaluated the conversion of cattle manure into a solid biofuel and the nutrient recovery potential of its combustion residues. Solid fuel was prepared from cattle manure collected in Gyeongsangbuk-do, Korea, and its fuel characteristics and ash composition were analyzed after combustion. Combustion tests conducted using a dedicated solid fuel boiler showed that an average lower heating value of 13.27 MJ/kg was achieved, meeting legal standards. Under optimized combustion, CO and NO_x emissions (129.9 and 41.5 ppm) were below regulatory limits (200 and 90 ppm); PM was also within the 25 mg/Sm³ standard. The bottom ash contained high concentrations of P₂O₅ and K, and its heavy metal content was below the regulatory threshold, suggesting its potential reuse as a fertilizer material. Although the Zn concentration in the fly ash exceeded the standard, its quantity was negligible. Therefore, the solid fuel conversion of cattle manure can become a viable and environmentally sustainable solution for both bioenergy production and nutrient recycling, contributing to improved waste management in livestock operations. Full article

This study investigates two novel algal biosorbents (Ulothrix sp. and Spirogyra sp.) from Djelfa, Algeria, for methylene blue (MB) removal from aqueous solutions. A comprehensive characterization, including scanning electron microscopy–energy dispersive X-ray spectroscopy (SEM–EDS), Brunauer–Emmett–Teller (BET) analysis, porosity measurements, and Fourier-transform infrared spectroscopy (FTIR), revealed distinct physicochemical properties. Ulothrix exhibited a surface area of 5.35 m²/g with an average pore diameter of 32.77 nm, whereas Spirogyra showed values of 3.47 m²/g and 20.97 nm for the surface area and average pore diameter, respectively. Despite their modest surface areas, both algae demonstrated effective adsorption capacities (6.94 mg/g for Spirogyra vs. 6.38 mg/g for Ulothrix), with optimal doses of 0.01 g and 0.08 g (for 50 mL of MB solution), respectively. Kinetic analysis confirmed pseudo-second-order adsorption (R² > 0.97), indicating chemisorption dominance. Isotherm data best fit the Sips model (R² = 0.94), suggesting heterogeneous monolayer formation. Thermodynamic studies revealed an endothermic (ΔH° > 0), spontaneous (ΔG° < 0), yet favorable adsorption process, highlighting the potential of these naturally abundant algae as sustainable biosorbents for dye wastewater treatment. Full article

Fischer–Tropsch synthesis (FTS) facilitates the conversion of syngas, derived from feedstocks such as biomass, coal, and natural gas, into valuable hydrocarbons (HCs). This investigation employed optimization methods, specifically Gibbs energy minimization, to perform a thermodynamic characterization of the low-temperature Fischer–Tropsch (LTFT) reaction for HC generation. The CONOPT3 solver within GAMS 23.2.1 software was utilized for solving the developed model. To represent the complex FTS product spectrum, twenty-three compounds, encompassing C₂–C₂₀ aliphatic hydrocarbons, were considered using a stoichiometric framework. The study explored the impact of operational parameters, including temperature (350–550 K), pressure (5–30 bar), and H₂/CO molar feed ratio (1.0–2.0/0.5–1.0), on hydrocarbon synthesis. Evaluation of the outcomes focused on HC yield and product characteristics. A significant sensitivity of the reaction to operating parameters was observed. Notably, lower temperatures, elevated pressures, and a H₂/CO ratio of 2.0/1.0 were identified as optimal for fostering the formation of longer-chain HCs. The developed model demonstrated robustness and efficiency, with rapid computation times across all simulations. Full article

Renewable energy sources (RES) are the foundation of the ongoing energy transition in Poland and worldwide. However, increased use of RES has brought several challenges, as most of these sources are dependent on weather conditions. The instability and lack of control over electricity production lead to both overloads and power shortages in transmission and distribution networks. A significant advantage of biogas plants over sources such as photovoltaics or wind turbines is their ability to control electricity generation and align it with actual demand. Biogas produced during fermentation can be temporarily stored in a biogas tank above the digester and later used in an enlarged CHP unit to generate electricity and heat during peak demand periods. While demand-driven biogas plants operate similarly to traditional installations, their development requires navigating regulatory and administrative procedures, particularly those related to the grid connection of the generated electricity. In Poland, it has only recently become possible to obtain grid connection conditions for such installations, following the adoption of the Act of 28 July 2023, which amended the Energy Law and certain other acts. However, the biogas sector still faces challenges, particularly the need for effective incentive mechanisms and the removal of regulatory and economic barriers, especially given its estimated potential of up to 7.4 GW. Full article

Membrane fouling remains a major challenge in full-scale membrane bioreactor (MBR) systems, reducing operational efficiency and increasing maintenance needs. This study introduces a predictive and analytic framework for membrane fouling by integrating artificial intelligence (AI)-driven feature engineering and explainable AI (XAI) using real-world data from an MBR treating food processing wastewater. The framework refines the target parameter to specific flux (flux/transmembrane pressure (TMP)), incorporates chemical oxygen demand (COD) removal efficiency to reflect biological performance, and applies a moving average function to capture temporal fouling dynamics. Among tested models, CatBoost achieved the highest predictive accuracy (R² = 0.8374), outperforming traditional statistical and other machine learning models. XAI analysis identified the food-to-microorganism (F/M) ratio and mixed liquor suspended solids (MLSSs) as the most influential variables affecting fouling. This robust and interpretable approach enables proactive fouling prediction and supports informed decision making in practical MBR operations, even with limited data. The methodology establishes a foundation for future integration with real-time monitoring and adaptive control, contributing to more sustainable and efficient membrane-based wastewater treatment operations. However, this study is based on data from a single full-scale MBR treating food processing wastewater and lacks severe fouling or cleaning events, so further validation with diverse datasets is needed to confirm broader applicability. Full article

Retired chemically polluted sites in southern Jiangsu Province, China, are characterized by dense nonaqueous phase liquids (DNAPLs) and extremely thick aquifers (>30 m), which pose substantial challenges for determining investigation and remediation depths during redevelopment and exploitation. This study constructed a 2D groundwater transport model using TMVOC to systematically investigate the migration, diffusion, and natural attenuation processes of two typical DNAPLs—1,2-dichloroethane (DCE) and carbon tetrachloride (CTC)—under three scenarios: individual transport, mixed transport, and heterogeneous aquifer conditions, with a simulation period of 35 years. In individual transport scenarios, DCE and CTC showed distinct migration behaviors. DCE achieved a maximum vertical transport distance of 14.01 m and a downstream migration distance of 459.58 m, while CTC reached 13.57 m vertically and 453.51 m downstream. When transported as a mixture, their migration was inhibited: DCE’s vertical and downstream distances decreased to 13.76 m and 440.46 m, respectively; and CTC’s to 13.23 m and 420.32 m, likely due to mutual solvent effects that altered their physicochemical properties such as viscosity and solubility. Under natural attenuation conditions, both DNAPLs ceased downstream transport by the end of the 6th year. DCE concentrations dropped below its risk control value (0.81 mg/L) by the 14th year, and CTC (with a risk control value of 0.23 mg/L) by the 11th year. By the 10th year, DCE’s downstream plume had retreated to 48.65 m, and CTC’s to 0.95 m. In heterogeneous aquifers, vertical upward transport of DCE and CTC increased to 14.82 m and 14.22 m, respectively, due to the partial absence of low-conductivity silt layers, while their downstream distances decreased to 397.99 m and 354.11 m, constrained by low-permeability lenses in the migration path. These quantitative results clarify the dynamic differences in DNAPL transport under varying conditions, highlighting the impacts of multicomponent interactions, natural attenuation, and aquifer heterogeneity. They provide critical references for risk management, scientific determination of remediation depths, and safe exploitation of retired chemically polluted sites with similar hydrogeological characteristics. Full article

The increasing demand for sustainable energy has spurred the exploration of advanced technologies for biodiesel production. This paper investigates the use of Dielectric Barrier Discharge (DBD)-generated low-temperature plasmas to enhance the conversion of fatty acid methyl esters (FAMEs) into hydrogenated fatty acid methyl esters (H-FAMEs) and other high-value hydrocarbons. A key mechanistic advance is achieved via in situ distillation: at the reactor temperature, unsaturated C18 and C20 FAMEs remain liquid due to their low melting points, while the corresponding saturated C18:0 and C20:0 FAMEs (with melting points of approximately 37–39 °C and 46–47 °C, respectively) solidify and deposit on a glass substrate. This phase separation continuously exposes fresh unsaturated FAME to the plasma, driving further hydrogenation and thereby delivering high overall conversion efficiency. The non-thermal, energy-efficient nature of DBD plasmas offers a promising alternative to conventional high-pressure, high-temperature methods; here, we evaluate the process efficiency, product selectivity, and scalability of this room-temperature, atmospheric-pressure approach and discuss its potential for sustainable fuel-reforming applications. Full article

The urbanization-driven surge in kitchen waste necessitates optimized dry anaerobic digestion (DAD; total solids > 15%). Despite its valorization potential, this technology requires efficiency improvements due to mass transfer constraints. This study evaluated TS effects (15%, 20%, or 25%) on methane production. The TS = 20% system achieved peak cumulative methane yield (405.73 ± 11.71 mL/gVS), exceeding TS = 15% (348.09 ± 12.19 mL/gVS) and TS = 25% (293.08 ± 3.55 mL/gVS). This optimization was attributable to synergistic maintenance of metabolic equilibrium through autonomous pH recovery, rapid VFAs degradation, and enhanced TAN tolerance. Conversely, TS = 25% exhibited impaired mass transfer efficiency under high solids, causing VFAs accumulation, ammonia toxicity, and progressive pH decline to 7.5, indicating system destabilization. Organic degradation analysis confirmed superior conversion efficiency in TS = 20% through dynamic SPS–SPN equilibrium. Microbial analysis revealed enhanced metabolic efficiency via synergistic interactions between acetoclastic and hydrogenotrophic methanogens in TS = 20%. This research provides technical parameters for optimizing methane production in kitchen waste DAD systems. Full article

Mercury is a highly toxic heavy metal that poses serious threats to human health and environmental safety, highlighting the critical importance of accurate Hg²⁺ detection. In this study, a novel fluorescent probe AP was synthesized by conjugating fluorescein, serving as the luminescent group, with pyridine-2-carboxaldehyde to enable selective Hg²⁺ detection. Hg²⁺ binds to AP in a 1:2 stoichiometric ratio, inducing the opening of the spiro-lactam ring and resulting in a significant fluorescence enhancement. The probe exhibited excellent selectivity and sensitivity toward Hg²⁺. A strong linear correlation was observed between its fluorescence intensity and Hg²⁺ concentration (R² = 0.99952), with a detection limit of as low as 9.75 × 10⁻⁸ mol/L. The average recoveries of Hg²⁺ across various water matrices ranged from 95.23% to 103.40%, with relative standard deviations (RSDs) below 3.07%. These results indicate that the probe performs effectively in real water-sample testing. Full article

Energy production is a global concern, encouraging the search for sustainable alternatives such as charcoal, a promising solid biofuel. This study evaluated the effects of temperature and carbonisation time on charcoal produced from Quercus wood. Carbonisation was carried out at 550 °C for 30 min, 700 °C for 30 min and under two progressive heating profiles: one starting at 550 °C for 30 min and increasing to 700 °C for a further 30 min, and another starting at 300 °C for 2 h and rising to 1000 °C for 10 min. Mass and volumetric yield, bulk density, proximate analysis, calorific value, energy yield and fuel ratio were determined. The results showed that carbonisation temperature affected charcoal properties. Mass and volumetric yields were highest at 550 °C (30.10% and 4.81 m³ t⁻¹) in Q. convallata and Q. urbanii. At higher temperatures, bulk density (0.56 g cm⁻³), fixed carbon (91.51%) and calorific value (32.82 MJ kg⁻¹) increased in Q. urbanii. Lower temperatures led to lower moisture levels (2.46%) and a higher energy yield (48.02%). Overall, temperatures above 700 °C improved energy properties, while those below 550 °C favoured higher yields. Species’ characteristics also influenced charcoal quality. These findings offer valuable insights into optimising the carbonisation of Quercus species and supporting the development of more efficient, sustainable charcoal production methods. Full article

In the context of wastewater treatment plant optimization, this study presents a novel approach based on a virtual sensor architecture designed to estimate total nitrogen levels in effluent and assess plant performance using an operational indicator. The core of the system is an intelligent agent that integrates real-time sensor data with machine learning models to infer nitrogen dynamics and anticipate deviations from optimal operating conditions. Central to this strategy is the operational nitrogen indicator (ONI), a weighted aggregation of four sub-indicators: legal compliance (Nactual%), the nitrogen dynamic trend (Tnitr%), removal efficiency (Enitr%), and microbial balance (NP%), each of which captures a critical dimension of the nitrogen removal process. The ONI enables the early detection of stress conditions and facilitates adaptive decision-making by quantifying operational status in terms of regulatory thresholds, biological requirements, and dynamic stability. This approach contributes to a shift toward smart wastewater treatment plants, where virtual sensing, autonomous control, and throttling-aware diagnostics converge to improve process efficiency, reduce operational risk, and promote environmental compliance. Full article

This work aims to assess the droplets produced by a novel evaporation process, proposed as an alternative for managing tequila vinasses, using a spectral camera with three spectral bands and a thermal camera mounted on an unmanned aerial vehicle (UAV). High-resolution satellite images with seven spectral bands complemented this characterization. The spectral characterization was conducted by comparing three experimental conditions: the background of the study area without droplets, the droplets generated from purified water, and the droplets produced from tequila vinasses. Two monitoring campaigns, conducted in November 2024 and January 2025, revealed that the tequila vinasse droplets exhibited a maximum influence radius of 16 m, primarily regulated by wind speed conditions (6–16 km/h). Thermal analysis identified the droplet plume as a zone with a lower temperature, creating a thermal contrast of up to 6.6 °C against the average background temperature of 36.6 °C. No significant difference was observed in the influence radius between the droplets generated from vinasse and those from potable water. Spectral analysis of the UAV and satellite images showed significant (p < 0.05) differences in reflectance when the droplets were present (e.g., the coastal blue band increased from an average of 14.43 to 95.59 when vinasse droplets were present). This suggests that the presence of chemical compounds altered light absorption and reflection. However, the instrument’s sensitivity limited the detection of organic compounds at concentrations below its detection limit. The monitoring data presented in this manuscript is crucial for developing strategies to mitigate the potential environmental impacts of the droplets emitted by this novel process. Full article

Since dust aerosols are one of the major pollutants in Georgia, it is important to study the aeolian desert dust (ADD) invasion to Georgia from the neighboring deserts to find out its contribution to the dust pollution problem. Therefore, the main objective of this study is to investigate the history, frequency and routes of ADD invasions to the Caucasus (Georgia) using modern models and technologies for 1.5 years. Using WRF-Chem/dust, CAMS and HYSPLIT mathematical models; MODIS satellite images; and PM10 field data, 38 cases of not strong ADD invasions to Georgia were found, and two typical cases are presented and analyzed in this paper. The results of the modeling studies from 15 March 2023 to 15 September 2024 showed that the WRF-Chem/dust (GOCART) v.4.5.1 model simulated the ADD transport to Georgia from the surrounding deserts quite well. Daily monitoring of ADD migration routes showed that in the easternmost region of Georgia (the most vinicultural and agricultural region), the number of ADD invasions was approximately three times higher than in other regions of Georgia, which is a novelty of this study due to the lack of ground dust measurement stations in the easternmost region of Georgia. Full article