Dear Colleagues,

Optical fibers coated with suitable protective layers are well suited to distributed fiber sensing systems (DFSS) based on Rayleigh, Raman, and Brillouin backscattering in small cross-sectional spaces and have found successful use in a wide variety of applications, including civil structures, transmission lines, railway, and downhole monitoring, among others. To improve overall system performance, many of these DFSS use multiple fibers. For example, DFSS use both single mode (SM) and multimode (MM) fibers for simultaneous measuring of several parameters, such as temperature and strain. The measured parameters are affected by wavelength-dependent loss caused by splices, stress on the optical fiber, fiber degradation in hydrogen environments, and radiation; this loss can also vary over time. As a compromise of SM and MM, the quasi-single mode operation in few mode (FM) fibers allows for larger input pump power before the establishment of detrimental effects induced by fiber nonlinearities, due to the well-controlled effective fundamental mode area. Moreover, FM supports only a few spatial modes, and the coupling between the fundamental mode and higher order modes can be largely suppressed with careful design. The performance of FM DFSS is mainly determined by the optical parameters of the used FM fibers. Thus, 2-mode and 4-mode FM fibers were designed and fabricated for DFSS, but the units do not limit the number of modes. An additional more advanced, single optical structure containing more than one core is multicore (MC) fibers, with small-diameter sensing elements that provide a high-density waveguide count. Using these fibers solves the problem of conduit and/or installation cable congestion and eliminates fiber-to-fiber positional error, as each waveguide in the MC fiber is permanently fixed in its parallel configuration with respect to other waveguides in the MC fiber structure. These MC fibers are typically coated with acrylate materials that are unsuitable for applications involving higher temperatures and harsh environments, such as may be encountered in many industrial sensing applications, but new coatings, for example, ETFE, are also proving useful.

Thus, this Special Issue aims to attract both theoretical and practical works that deal with optical fibers as a key element of DFSS. Of particular interest are submissions on, but not limited to, basic technologies of the modeling, design, fabrication, and utilization of optical fibers for different, including extremal, applications of DFSS; the effect of optical fibers’ characteristics on the performance of DFSS in general; and problems regarding the interconnections of different fiber types. This Special Issue will also focus on the fiber construction in modern DFSS multiplexing of the three main backscattering mechanisms—Rayleigh, Raman, and Brillouin—in conjunction with fiber Bragg gratings written in SM, MM, FM, and MC fibers. Review articles that describe the current state of the art are also welcome.

Dr. Oleg Morozov
Guest Editor

Manuscript Submission Information

Manuscripts should be submitted online at www.mdpi.com by registering and logging in to this website. Once you are registered, click here to go to the submission form. Manuscripts can be submitted until the deadline. All submissions that pass pre-check are peer-reviewed. Accepted papers will be published continuously in the journal (as soon as accepted) and will be listed together on the special issue website. Research articles, review articles as well as short communications are invited. For planned papers, a title and short abstract (about 100 words) can be sent to the Editorial Office for announcement on this website.

Submitted manuscripts should not have been published previously, nor be under consideration for publication elsewhere (except conference proceedings papers). All manuscripts are thoroughly refereed through a single-blind peer-review process. A guide for authors and other relevant information for submission of manuscripts is available on the Instructions for Authors page. Fibers is an international peer-reviewed open access monthly journal published by MDPI.

Please visit the Instructions for Authors page before submitting a manuscript. The Article Processing Charge (APC) for publication in this open access journal is 2000 CHF (Swiss Francs). Submitted papers should be well formatted and use good English. Authors may use MDPI's English editing service prior to publication or during author revisions.

• SM fibers
• MM fibers
• FM fibers
• MC fibers
• fiber bragg gratings in DFSS
• quasi-distributed fiber sensor systems
• optomechanics of fibers
• fibers for arctic applications
• fibers for atom energetics applications
• fibers for underwater applications
• fibers for space applications
• fibers for railway applications
• fibers for high-voltage applications
• technologies and means for optical fiber monitoring
• materials for optical fiber sensing development
• photonic crystal fibers for sensing applications
• fiber sensor systems for aviation and space applications