Next Article in Journal
High-Order Spectral Irregular Wave Generation Procedure in Experimental and Computational Fluid Dynamics Numerical Wave Tanks, with Application in a Physical Wave Tank and in Open-Source Field Operation and Manipulation
Next Article in Special Issue
Mega Ports’ Mitigation Response and Adaptation to Climate Change
Previous Article in Journal
Micromechanical Analysis of Lateral Pipe–Soil Interaction Instability on Sloping Sandy Seabeds
Previous Article in Special Issue
The State of the Hydrographic Survey and Assessment of the Potentially Risky Region for Navigation Safety
 
 
Font Type:
Arial Georgia Verdana
Font Size:
Aa Aa Aa
Line Spacing:
Column Width:
Background:
Article

Life Cycle Assessment of Utilizing Bio-Oil to Reduce the Carbon Footprint on the Yangtze River Mainline: A Case Study of Container Ships

Faculty of Maritime and Transportation, Ningbo University, Ningbo 315211, China
*
Author to whom correspondence should be addressed.
J. Mar. Sci. Eng. 2024, 12(2), 226; https://doi.org/10.3390/jmse12020226
Submission received: 29 December 2023 / Revised: 19 January 2024 / Accepted: 20 January 2024 / Published: 26 January 2024
(This article belongs to the Special Issue Recent Research on Sustainable and Safe Maritime Transportation)

Abstract

:
In the context of ecological protection and strict emissions control, the replacement of traditional energy sources with clean energy has become a new direction for the development of the shipping industry. Bio-oil is beneficial to reduce greenhouse gas (GHG) emissions and air pollutants. In this study, life cycle assessment (LCA) and life cycle cost assessment (LCCA) are conducted to evaluate the environmental and economic impacts of diesel and bio-oil as fuel for container ships in the Yangtze River mainline. The results show that compared with diesel, the total greenhouse gas emission is 34.58% lower than diesel, and the total cost is 8.22% higher than that of diesel throughout the whole life cycle of these two fuels. Both LCA results and LCCA results show that bio-oil is an ideal clean energy source. In addition, the abundant raw material resources of bio-oil make it a reliable alternative, which is also of great significance.

1. Introduction

Due to the large amount of human-caused greenhouse gas emissions that have exacerbated global climate change, carbon emission reduction has become the consensus of all countries in the world [1]. The Global Warming Potential (GWP) was developed to compare the contribution of different gases to global warming, expressed as CO2-equivalent (CO2-eq) [2]. The Sixth Assessment Report of the Intergovernmental Panel on Climate Change (IPCC) states that global surface temperatures have risen faster in the last 50 years than in any of the last 2000 years [3]. Therefore, immediate actions to reduce carbon emissions should be taken.
In recent years, ship emissions have become a growing concern. According to the 4th Greenhouse Gas study conducted by the International Maritime Organization (IMO), maritime transport operations emit approximately 1.056 billion tons of carbon dioxide per year, accounting for about 2.89 percent of global greenhouse gas emissions [4]. Three ship types, namely, container shipping, bulk carriers, and oil tankers, are the primary contributors to international shipping’s greenhouse gas (GHG) emissions [4]. Container shipping has been one of the fastest-growing sectors of the shipping industry for the past three decades and is likely to continue to grow rapidly in the future [5]. Therefore, reducing CO2 emissions is an important issue that the container shipping industry must combat to achieve environmental sustainability.
IMO continues to develop and introduce mandatory regulations for energy saving and emission reduction to achieve GHG-reduction targets as soon as possible. IMO implemented the Energy Efficiency Design Index (EEDI) to new ships and the Ship Energy Efficiency Management Plan (SEEMP) to all ships in 2011 [1]. IMO adopted the Initial Strategy for Reducing Greenhouse Gas Emissions from Ships In 2018, followed by a set of guidelines in 2022 to facilitate the implementation of the short-term measure of GHG reduction for ships. Over the past decade, the IMO has taken further action, including further regulatory measures and the revised IMO Greenhouse Gas Strategy to be adopted in 2023 [6]. To support the implementation of these programs, IMO has been implementing a comprehensive program of capacity building and technical assistance, including a series of global projects [7].
Reducing the Carbon Footprint (CF) of the shipping industry can be achieved through certain technical measures, such as replacing traditional fossil fuels with clean fuels. Currently, heavy fuel oil (HFO) is the main fuel used in the shipping industry, which has a high carbon content and generates a lot of greenhouse gases through combustion [8,9]. The use of alternative fuels, such as natural gas, hydrogen, methanol, and biofuel, can help mitigate greenhouse gas emissions. The biofuels presented in this paper are considered “carbon neutral”, meaning that the greenhouse gases emitted from the combustion of biofuels are absorbed by the growing biomass, and the new biomass is further used in the production of biofuels.
Biomass energy has become the fourth largest energy source after coal, oil, and natural gas. It currently accounts for about 10% of the world’s primary energy consumption and it is the most widely used renewable resource with significant emission-reduction effects [10]. According to an estimation by the World Wide Fund for Nature (WWF), the global potential availability of biomass energy amounts to 8212 million tons of standard oil per year. Bio-oil can be obtained by using biomass pyrolysis and is regarded as a promising alternative fuel for fossil fuels due to its advantages of renewability, low carbon emissions, and abundant raw materials.
As an energy product, energy consumption and carbon emissions are present throughout the whole life cycle of bio-oil, from raw material extraction and production to its use, which will affect the surrounding environment to varying degrees. Therefore, it is necessary to study the carbon emission intensity of bio-oil as a marine alternative fuel by using life cycle assessment.
Compared with fossil fuels, bio-oils can reduce CO2 emissions by at least 70%. Wang et al. [11] made a comparative life cycle assessment of marine diesel, liquefied natural gas, methanol, biodiesel, and hydrogen with various energy production methods and studied their environmental impacts on super yachts. Their study investigated energy consumption and the environmental impact of alternative low-emission fuels over the complete vessel lifetime. The results show that the GHG emission reduction of replacing marine gas oil with bio-methanol and bio-diesel is 78.9% and 19.2%, respectively. By conducting a life cycle assessment (LCA) on the first high-power prototype offshore wind farm in China, Chen et al. [12] found that the construction and wind turbine manufacturing stages contribute the most to the environmental impact during the entire lifecycle of this wind farm case. This case can reduce energy consumption and greenhouse gas emissions by 9.23 MJ and 767.9 g CO2-eq for every 1 kWh of electricity produced, respectively. Balcombe et al. [13] applied a comprehensive LCA and life cycle assessment (LCCA) of Liquefied Natural Gas (LNG) as a marine fuel with new emission measurement and supply chain data. The results show that LNG improves the air quality impact, reduces fuel costs, and generates moderate climate benefits. With the best-performing LNG engine and the optimized LNG supply chain, the GWP can be reduced by 28%. Obydenkova et al. [14] proposed a biomass solvolysis route for crude lignin oil (CLO) production from forest residues and applied both LCA and life cycle impact assessment (LCIA) to such a biorefinery concept. The results show that by using such CLO as drop-in biofuel for methanol-propelled ships, up to 84% GHG emission reduction can be achieved compared to fossil alternatives. Kesieme et al. [15] evaluated a life cycle assessment of upstream pathways toward straight vegetable oil (SVO) and biodiesel for shipping. The results show that the cultivation location has a strong influence on the environmental impacts of various pathways due to the differences in yield. Watanabe et al. [16] concluded that the climate mitigation potential of biofuels relative to fossil alternatives is 65–85% in the short term (GWP20) and 78–87% in the long term (GWP100) climate impact.
The purpose of this paper is to evaluate the environmental and economic impact of replacing diesel with bio-oil for ship propulsion. Taking container ships on the Yangtze River mainline in the Anqing–Nanjing section as an example, the GHG emission and life-cycle carbon costs of diesel and bio-oil are determined by full LCA and LCCA.

2. LCA Calculation Model

Life Cycle Assessment is a cradle-to-grave assessment. The main idea is to consider the impact throughout the whole life cycle from raw material acquisition, manufacturing, transportation, operation and use, and secondary use of key components to end-of-life recycling during the assessment [17]. It is now widely used to evaluate the environmental impact of products, processes, and activities.
The LCA consists of four steps: definition of objectives and scope, inventory analysis, impact assessment, and interpretation of results [18]. In this paper, the objective of the LCA is to investigate the environmental impact of diesel and bio-oil as ship fuels, focusing only on greenhouse gas emissions—that is, the carbon footprint released during a twenty-year ship lifetime. The scope defines the functional units, system boundaries, data allocation procedures, data requirements, and quality criteria for original data quality requirements for diesel and bio-oil. The functional unit is the carbon footprint released by the consumption of diesel and bio-oil for propulsion over the life of the ship, expressed in ton CO2-eq (tCO2-eq). The system boundary used in this paper is the “Well to Wheel (WTW)” approach, as shown in Figure 1.
In this paper, the WTW is divided into two main stages, namely, the Well-to-Pump (WTP) stage and the Pump-to-Wheel (PTW) stage. The WTP stage, also known as the fuel production stage, includes crude oil or raw biomass extraction and transportation, fuel production and transportation, distribution, storage, and refueling processes. The PTW stage, also known as the fuel use stage, focuses on fuel consumption and greenhouse gas emissions of ship main engines [19]. The assessment compares the total life-cycle emissions of bio-oils with that of diesel to provide insight into the feasibility of alternative fuels in the shipping industry.

2.1. WTP Stage

Total carbon emissions (EWTP) from the production of 1 t of refined oil or bio-oil in the WTP stage are calculated by Equation (1). The WTP stage includes four sub-stages: raw material extraction (E1), raw material transportation (E2), oil refinery or bio-oil production (E3), and refined oil transportation (E4). The carbon emissions from each sub-stage are calculated separately for every 1 t of refined oil or bio-oil produced within the life mileage.
E W T P = E 1 + E 2 + E 3 + E 4
In this study, the crude oil for diesel production comes from the Jiangsu Oilfield. The crude oil is first transportation by tanker truck from Gaoyou, Yangzhou, to Zhoushan Port, Ningbo (510 km). Then, the crude oil is loaded into an oil tanker and shipped to Nanjing Wharf (556 km). Finally, it is transported through pipelines to the refinery (20 km). After diesel oil is produced, it is transported to the gas station (310 km) by tanker truck. The bio-oil is made from oil palms. The bio-oil refinery is built 20 km away from the oil palm plantation, and the harvested oil palm is transported to the refinery by truck. After the bio-oil is produced, it is first transported by tanker truck to Shuifu dock (1100 km) and then transported to Anqing gas station (2100 km) through the waterway.

2.1.1. Raw Material Extraction Stage

The raw material of diesel oil is crude oil, and the crude oil extraction stage mainly includes the steps of oil well exploration, crude oil extraction, crude oil gathering and handling, and crude oil storage and transportation. The carbon emissions in the crude oil extraction stage mainly come from the combustion of fuels used in various types of industrial boilers and engines and from the use of indirect energy such as electricity [19]. This is calculated by multiplying the amount of crude oil required to produce 1 t of diesel or bio-oil (α, t/t) by the carbon emissions from the extraction of 1 t of crude oil (e1, kg/t), such as in the following equation:
E 1 = α × e 1
Based on the data from the National Bureau of Statistics, the average amount of crude oil consumption of 1 ton of diesel oil in China is 2.95 t. According to the carbon emission data regarding the unit crude oil exploitation stage in the GREET model (https://greet.anl.gov/index.php?content=greetdotnet, accessed on 9 October 2023), the average CO2 emission of 1 ton of crude oil exploitation is 0.03638 t after conversion [20].
The raw materials of bio-oil are mainly biomass, such as oil palm, corn straw, and rapeseed hulls. The data on bio-oil in this paper are from bio-oil made from oil palm [21]. In China, oil palm is mainly grown in tropical areas such as Hainan, Yunnan, Guangdong, and Guangxi. The residue of oil palm can be used as biomass fuel. Oil palm fruits grow in bunches, and they are orange-red when ripe, commonly known as oil palm fruit bunches. The fruit bunches are separated by hand or mechanically and split into palm fruit and palm empty fruit bunches. Palm fruit bunches contain about 60–70% moisture, and after mechanical crushing and drying, they become shredded, and the moisture can be reduced to less than 50%, which can be directly burned in boilers as biomass fuel. The palm fruit can be divided into three layers: the outer layer is the palm mesocarp, the middle layer is the palm shell, and the inner layer is the kernel. The mesocarp is pressed to extract palm oil, and the residue is Mesocarp Fiber (MF), which can be used as biomass fuel. The kernels are pressed to extract palm kernel oil, and the residue is a palm kernel cake (CAKE), which can also be used as a biomass fuel. The shell is hard, uniform in size, has good liquidity, is low in moisture, and is high in calorific value, making it a very good biomass fuel that can be burned directly in a furnace [22]. Considering that oil palm absorbs carbon dioxide through photosynthesis during its growth process and taking into account land use change issues, this stage results in negative carbon emissions [23].

2.1.2. Raw Material Transportation Stage

After extraction, the raw materials need to be transported to the refineries in various locations for processing. It is assumed that the loss of raw materials in the transportation stage is not considered. The carbon emission in the transportation stage mainly comes from the energy consumption of transportation means. Possible methods of raw material transportation include pipeline, rail, water, and road transportation. Given the different fuels used by various transportation modes, data on average distance, typical transportation means, and emission factors of each transportation mode are required to calculate carbon emissions at this stage (see Table 1 for details [24]). The carbon emissions of producing 1 ton of fuel in the crude oil transportation stage are calculated by Equation (3) as follows:
E 2 = α × L 1 × S × [ β 1 × m ] × b
where α denotes the consumption of crude oil for production of 1 t fuel, t/t; L1 refers to the average distance of each transportation mode, km; S refers to the energy intensity of each transportation mode, KJ/(t·km); β1 denotes the proportion of fuel used by each transportation mode; m denotes the carbon emission factor of each transportation mode, g/MJ; and b denotes the proportion of each transportation mode.

2.1.3. Refinery Production Stage

Carbon emissions in the refinery production stage include direct emissions and indirect emissions. Direct emissions include combustion emissions, process emissions, and fugitive emissions. Combustion emissions are generated from the combustion of fossil fuels during the refinery production process, process emissions are generated during the refinery production process, and fugitive emissions are leakage or unintentional discharge of gases or vapors during the working process. Indirect emissions mainly include those generated from the use of purchased electricity and steam. The specific calculation method used in this paper is based on the standard of the Chinese petroleum and chemical industry [25], as shown in Equation (4):
E 3 = P r × E a ÷ C
where Pr refers to the energy consumption used for producing 1 ton of fuel, t/t; Ea refers to the total carbon emission of the refinery, kg; and C refers to the total energy consumption equivalent of the refinery, kg.

2.1.4. Transportation of Refined Oil Products

The calculation method to determine the carbon emissions of the refined oil transportation stage is similar to that used in the raw material transportation stage. The only difference is that the carbon emissions are calculated per unit of refined oil transportation in this stage, as shown in Equation (5). To calculate the carbon emissions of this stage, the data on the transportation mode, average distance, typical transportation means in each transportation mode, and their emission factors are required. The data used in this study are listed in Table 2.
E 4 = L 2 × S × [ β 2 × m ] × b
where L2 denotes the average distance of each transportation mode, km; β2 denotes the proportion of fuel used by each transportation mode; m refers to the carbon emission factor of each transportation mode, g/MJ; and b refers to the proportion of each transportation mode.

2.2. PTW Stage

In this paper, the Anqing–Nanjing section of the Yangtze River was selected, as shown in Figure 2. The details of the selected Yangtze River mainline container ship with an annual transportation plan are shown in Table 3 [26]. Assuming that the lifetime (LT) of this vessel is fifteen years, the life mile (LM) is calculated by Equation (6):
L M = L T × N A × 2 × l
where NA refers to the number of round trips per year.
The existing power system configuration with a new diesel engine is set as the baseline. Given that the ships have been in use for a short time, it is assumed that the new diesel engine will be replaced within the next 15 years. During this period, the emissions of the different fuels used on these ships are analyzed.
Due to the actual conditions, such as weather conditions and fuel consumption, the actual operating speed of the ship differs from the design speed (Vde). The average ship speed (Vave) is the route length (l) divided by the trip duration (t). The average ship power (Pave) is related to the main engine(s) power and is calculated by Equation (7) as follows:
P a v e = P M E × 0.8 × ( V a v e V d e ) 3
Then, the energy consumption per unit distance (EC, kWh/nm) is calculated according to Equation (8):
E C = P a v e V a v e
Assuming that the energy requirements and energy consumption per unit distance are the same for different power system configurations on existing diesel-powered vessels, the fuel consumption per unit distance (FC, kg/nm) of the vessel is calculated by Equation (9):
F C = E C × S F C
SFC refers to the unit fuel consumption of different fuels, also known as the engine fuel consumption rate. The fuel consumption rates of bio-oil are relatively higher than that of diesel [28].
In the shipping sector, the PTW stage means the fuel use stage—that is, the operation stage of the ship. This stage has exhaust emissions (TE, g/nm) from fuel combustion in the engine. The TE is calculated by multiplying the fuel consumption per unit distance of the ship by the greenhouse gas emission factor of various types of pollutants (EFi), as shown in Equation (10):
T E i = F C × E F i
where i denotes the different types of pollutants.
Greenhouse gases released during the life cycle of the ship by using diesel and bio-oil are expressed in CO2-eq, as shown in Equation (11):
C F = G W P C O 2 × T E C O 2 + G W P C H 4 × T E C H 4 + G W P N 2 O × T E N 2 O
In summary, the total GHG emissions in the WTP phase and PTW stage are calculated in Equation (12) and Equation (13), respectively:
W T P = ( E 1 + E 2 + E 3 + E 4 ) × L M × E C × S F C
P T W = C F × L M

3. LCCA Calculation Model

In order to compare the cost of diesel and bio-oil power units, we need to perform a full life cycle cost assessment of both power systems, which means calculating the total cost of all units over the life of the ship. The total cost includes the investment cost and the development cost. Among them, the investment cost (Cin) includes the ship’s price, engine price, and conversion price. It is calculated by multiplying the average power of the ship by an assumed conversion factor of 1727 CNY/kW [29], as shown in Equation (14):
C i n = P a v e × 1727
The development cost includes the fuel cost, maintenance cost, and carbon emission cost. In China, the price of diesel fuel (PRD) for diesel-powered ships is 6.2 CNY/kg, and the price of bio-oil (PRB) is 5.9 CNY/kg. The life cycle fuel cost (LCFC) is calculated according to Equation (15):
L C F C = L M × F C × P R
where LM denotes life mileage and FC denotes fuel consumption per unit distance of the ship.
According to the work of Iannaccone [30], the ship maintenance cost is assumed to be 0.097 CNY/kWh. The life cycle maintenance cost (LCMC) is calculated as follows:
L C M C = L M × E C × 0.097
where EC refers to the energy consumption of the ship.
Carbon tax refers to the cost of allowed CO2 emissions, which is based on the price of CO2 (CR). There is no cost of carbon emission in the shipping industry yet, but it is necessary to evaluate the cost of carbon emissions because such a carbon price will certainly lead to extra costs for shipping companies. Moreover, there may be a limit on carbon emission allowances in the future. The estimation of carbon tax for China from 2026 to 2040 (CNY/t CO2) is adopted over a span of 15 years from the World Energy Outlook 2019 [31]. The World Energy Outlook 2019 includes CO2 prices in three different scenarios, and only the current policy scenario is discussed here. The current policy scenario refers to the policies implemented in the energy sector currently and does not consider any policy changes in the future. In addition to this, there are prescribed policy scenarios and sustainability scenarios shown in Figure 3. The life cycle carbon emission cost (LCCEC) over a span of 15 years for different scenarios is calculated in the same way according to Equation (17):
L C C E C = i = 1 15 P T W A , i × C R i
where PTWA,i refers to the average annual tailpipe emissions, and CRi refers to the tax price of CO2 in year i.

4. Results

4.1. LCA Results

Taking a Yangtze River mainline container ship as an example, the environmental and economic influences of utilizing diesel and bio-oil fuels in the ship’s power system were evaluated. The emission factors and the global warming potential of greenhouse gases for both fuels are presented in Table 4. The emission factor for diesel fuel is adopted from the fourth IMO GHG study, which is approximately 3206 g of CO2 per kilogram of fuel. The carbon emission factor of bio-oil in the refinery production stage is derived from the research of Chan et al. [21]. The specific life cycle assessment results are shown in Figure 4.
The LCA results show that the total emissions of bio-oil fuels are lower and environmentally friendly compared to diesel. In the WTP stage, the exhaust emission of diesel fuel is only 7522.9461 tCO2-eq, which only accounts for about 11.53% of the whole life cycle exhaust emission. In contrast, the emissions of bio-oil fuels in the WTP stage are much higher than those of diesel fuels, being almost 2 times higher than those of diesel fuels. The major exhaust emissions of bio-oil fuels come from the bio-oil manufacturing stage, which is consistent with the research results of Chan et al. [21]. The share of diesel fuel in this stage is around 6.52%, while the share of bio-oil fuel reaches around 169.14%. The data exceeding 100% are due to the fact that oil palm plants absorb carbon dioxide during their growth process, resulting in a total carbon emission throughout the lifecycle that is lower than the production stage of bio-oil fuel. The production process of bio-oil, like fast pyrolysis, is more energy consuming than that of diesel. In this stage, the energy consumption of the bio-oil pretreatment process and production process account for 98.49% of the whole bio-oil production process, which is consistent with the results of Ng et al. [32]. Therefore, emission reduction during the production of bio-oil fuel may become the focus of future research.
The carbon emission of diesel fuel mainly occurs in the PTW stage. The carbon emission of diesel in the PTW stage is 57,746.409 tCO2-eq, which accounts for about 88.47% of the whole life of diesel. Meanwhile, the carbon emission of bio-oil in the PTW stage is 29,009.2881 tCO2-eq, accounting for about 67.93% of the carbon emission in its whole life cycle. The carbon emissions of bio-oil are only 50.24% of those of diesel during the ship’s operational phase. The carbon emissions released during bio-oil combustion are the carbon dioxide absorbed by oil palms through photosynthesis; thus, bio-oil is generally considered to be “carbon neutral”. The utilization of bio-oil in ship power system configuration reduces the carbon footprint by approximately 34.58% compared to that of diesel.

4.2. LCCA Results

To reduce half of the carbon emissions in the shipping sector by 2050, which was committed by IMO in the initial Greenhouse Gas Strategy, possible policies, including carbon prices, may be required. Thus, when applying LCCA, the cost of carbon emissions throughout the life cycle of the ship needs to be considered. Table 5 shows the carbon emissions during the operation of the ship and the carbon emission cost based on the carbon price of the current policy scenario. The results of the specific life cycle cost assessment are shown in Figure 5.
Since the two fuels are used in the same type of ship, the investment costs and maintenance costs are assumed to be the same. The difference lies in the fuel cost and carbon emission cost. As shown in Figure 5, the fuel cost of bio-oil is higher than diesel fuel because, although the price of bio-oil is slightly lower than diesel, the fuel consumption per unit distance is higher for bio-oil compared to diesel. Meanwhile, the low carbon cost of bio-oil is due to much lower carbon emissions compared to those of diesel fuel during the operation of the ship.

4.3. Sensitivity Analysis

The results of the LCCA analysis in this paper are based on an assumed ship life of 15 years. The ship’s life affects the overall results, so a sensitivity analysis was performed. In this case, the ship’s life is treated as an uncertainty factor, and different results are considered for the ship’s life cycle of 5, 10, and 15 years.
Different ship life cycles have a proportional relationship with investment costs, maintenance costs, and carbon emissions costs, so no comparison is made here. The factor of the ship’s lifetime mainly affects the carbon tax, as these costs increase disproportionately over time. As can be seen in Figure 6, the annual average life cycle carbon costs of both ship power systems are lower than for 10 and 15 years of life when the ship life is 5 years. However, regardless of whether it has a 5-year, 10-year, or 15-year life cycle, the carbon emission cost of bio-oil is approximately 49.76% lower than that of traditional diesel. In the other two scenarios, the carbon emission cost of diesel is also higher than that of bio-oil. In the stated policies scenario, the carbon emission cost of diesel oil is about 11.19 million CNY, while that of bio-oil is about 5.6 million CNY. In the sustainable development scenario, the carbon emission cost of diesel oil is about 36.87 million CNY, while that of bio-oil is about 18.52 million CNY.

5. Conclusions

In this paper, the life cycle carbon emission and carbon emission cost of utilizing diesel and bio-oil as fuel for container ships on the Yangtze River mainline are calculated and compared based on the life cycle assessment theory. The WTW approach, which is further divided into the WTP and PTW stages, is adopted as the system boundary when applying LCA and LCCA analysis, while the data required for calculating the carbon emission in each stage are gathered.
According to the results of LCA and LCCA analysis, the total emissions of bio-oil fuels are only 34.58% lower than diesel, and the total cost is 8.22% higher than that of diesel; this fuel is still something to look forward to. Considering the global energy crisis, if fossil fuels are used all the time, this non-renewable energy source will be depleted at some point in the future. The abundance of biomass energy makes bio-oil fuel a highly desirable alternative fuel.
The accuracy and applicability of the data are the keys to the calculation of the whole life cycle carbon emissions, which requires a lot of data. Additionally, due to constraints in research duration, this paper only utilizes data pertaining to bio-oil derived from palm. A comparative analysis involving bio-oil from various alternative raw materials will be been conducted in further research. Using the progress of the research in this paper, taking the current research status of related aspects into account, the following perspectives are proposed for the research on the whole life cycle carbon emissions of bio-oil.
In the future, the ship power energy represented by bio-oil is undoubtedly a direction for shipping practitioners to work and a trend for the development of new energy power systems of ships in the future. In the face of the depletion of fossil energy and increasingly serious emission pollution, environmental protection measures have been strengthened, and supportive policies for the development of new clean energy sources have been implemented to promote development all over the world. With the continuous development and application of information technology, new energy research will develop faster and faster in the future. As a major oil importer, China consumes huge amounts of oil, so it is urgent to promote new energy power systems in China.

Author Contributions

C.L.: Investigation, Experimentation, Data Curation, Writing—Original draft. Y.Z. (Yingying Zhu): Conceptualization, Investigation, Methodology, Supervision, Writing—Review and Editing. J.Z.: Investigation, Data Curation, Validation. Y.Z. (Yifan Zhao): Investigation, Validation. G.C.: Conceptualization, Investigation, Methodology, Supervision, Writing—Review and Editing. All authors have read and agreed to the published version of the manuscript.

Funding

This research is supported by the Ningbo Natural Science Foundation, China (grant No. 2022J109), and the Natural Science Foundation of Zhejiang Province, China (grant No. LY20E060003).

Data Availability Statement

The data presented in this study are openly available.

Conflicts of Interest

The authors declare no conflicts of interest.

References

  1. Shi, Y. Are greenhouse gas emissions from international shipping a type of marine pollution? Mar. Pollut. Bull. 2016, 113, 187–192. [Google Scholar] [CrossRef]
  2. Yaman, A.B.; Sevimoglu, O. Assessment and modelling of greenhouse gas emissions from waste collection vehicles powered by different fuel types. Int. J. Global Warm. 2021, 23, 274–295. [Google Scholar] [CrossRef]
  3. Wang, X.J.; Wu, G.C.; Qin, Y.Y. Day-to-Day Temperature Variability in China During Last 60 Years Relative to Arctic Oscillation. Earth Space Sci. 2022, 9, e2022EA002587. [Google Scholar] [CrossRef]
  4. Singh, S.; Rambarath-Parasram, V. Considerations for the Latin American and Caribbean Region in Light of the Global Move Towards Low Carbon Shipping. In Best Practices in Manufacturing Processes: Experiences from Latin America; García Alcaraz, J.L., Rivera Cadavid, L., González-Ramírez, R.G., Leal Jamil, G., Chong Chong, M.G., Eds.; Springer International Publishing: Cham, Switzerland, 2019; pp. 53–73. [Google Scholar]
  5. Korlak, P.K. Prediction of the very- and ultra-large Container Ships’ Electricity Generation Capacity at the Initial Design Stage. Nase More 2022, 69, 103–113. [Google Scholar] [CrossRef]
  6. Wan, Z.; El Makhloufi, A.; Chen, Y.; Tang, J. Decarbonizing the international shipping industry: Solutions and policy recommendations. Mar. Pollut. Bull. 2018, 126, 428–435. [Google Scholar] [CrossRef] [PubMed]
  7. Serra, P.; Fancello, G. Towards the IMO’s GHG Goals A Critical Overview of the Perspectives and Challenges of the Main Options for Decarbonizing International Shipping. Sustainability 2020, 12, 3220. [Google Scholar] [CrossRef]
  8. Lou, H.J.; Hao, Y.J.; Zhang, W.W.; Su, P.H.; Zhang, F.; Chen, Y.J.; Feng, D.L.; Li, Y.F. Emission of intermediate volatility organic compounds from a ship main engine burning heavy fuel oil. J. Environ. Sci. 2019, 84, 197–204. [Google Scholar] [CrossRef]
  9. Puskar, M.; Kopas, M.; Puskar, D.; Lumnitzer, J.; Faltinova, E. Method for reduction of the NO(X) emissions in marine auxiliary diesel engine using the fuel mixtures containing biodiesel using HCCI combustion. Mar. Pollut. Bull. 2018, 127, 752–760. [Google Scholar] [CrossRef]
  10. Zhang, S.H.; Shao, J.N.; Lan, C.C.; Bi, Z.X.; Lv, Q. Application status and prospect of biomass energy in ironmaking process. Iron Steel 2022, 57, 13–22. [Google Scholar] [CrossRef]
  11. Wang, Y.F.; Maidment, H.; Boccolini, V.; Wright, L. Life cycle assessment of alternative marine fuels for super yacht. Reg. Stud. Mar. Sci. 2022, 55, 102525. [Google Scholar] [CrossRef]
  12. Chen, J.J.; Mao, B.J.; Wu, Y.F.; Zhang, D.Y.; Wei, Y.Q.; Yu, A.; Peng, L.H. Green development strategy of offshore wind farm in China guided by life cycle assessment. Resour. Conserv. Recy 2023, 188, 106652. [Google Scholar] [CrossRef]
  13. Balcombe, P.; Staffell, I.; Kerdan, I.G.; Speirs, J.F.; Brandon, N.P.; Hawkes, A.D. How can LNG-fuelled ships meet decarbonisation targets? An environmental and economic analysis. Energy 2021, 227, 120462. [Google Scholar] [CrossRef]
  14. Obydenkova, S.; Defauw, L.; Kouris, P.; Smeulders, D.; Boot, M.; van der Meer, Y. Environmental and Economic Assessment of a Novel Solvolysis-Based Biorefinery Producing Lignin-Derived Marine Biofuel and Cellulosic Ethanol. Energies 2022, 15, 7. [Google Scholar] [CrossRef]
  15. Kesieme, U.; Pazouki, K.; Murphy, A.; Chrysanthou, A. Attributional life cycle assessment of biofuels for shipping: Addressing alternative geographical locations and cultivation systems. J. Environ. Manag. 2019, 235, 96–104. [Google Scholar] [CrossRef]
  16. Watanabe, M.D.B.; Cherubini, F.; Cavalett, O. Climate change mitigation of drop-in biofuels for deep-sea shipping under a prospective life-cycle assessment. J. Clean. Prod. 2022, 364, 132662. [Google Scholar] [CrossRef]
  17. Fenner, A.E.; Kibert, C.J.; Woo, J.; Morque, S.; Razkenari, M.; Hakim, H.; Lu, X.S. The carbon footprint of buildings: A review of methodologies and applications. Renew. Sust. Energ. Rev. 2018, 94, 1142–1152. [Google Scholar] [CrossRef]
  18. Adhikari, B.; Lister, T.E.; Reddy, R.G. Techno-economic and life cycle assessment of aluminum electrorefining from mixed scraps using ionic liquid. Sustain. Prod. Consum. 2022, 33, 932–941. [Google Scholar] [CrossRef]
  19. Rahman, M.M.; Canter, C.; Kumar, A. Well-to-wheel life cycle assessment of transportation fuels derived from different North American conventional crudes. Appl. Energ. 2015, 156, 159–173. [Google Scholar] [CrossRef]
  20. Cheng, D.R. Carbon Emissions Calculation of Gasoline and Diesel Fuel Based on Life Cycle Assessment. Master’s Thesis, China University of Petroleum, Beijing, China, 2016. [Google Scholar]
  21. Chan, Y.H.; Yusup, S.; Quitain, A.T.; Tan, R.R.; Sasaki, M.; Lam, H.L.; Uemura, Y. Effect of process parameters on hydrothermal liquefaction of oil palm biomass for bio-oil production and its life cycle assessment. Energy Convers. Manag. 2015, 104, 180–188. [Google Scholar] [CrossRef]
  22. Ayodele, B.V.; Cheng, C.K. Biorefinery for the Production of Biodiesel, Hydrogen and Synthesis Gas Integrated with CHP from Oil Palm in Malaysia. Chem. Prod. Process Model. 2016, 11, 305–314. [Google Scholar] [CrossRef]
  23. Xu, Y.W. Study of Biodiesel Life Cycle Assessment and Low Temprature Combustion of Biodiesel Engine. Master’s Thesis, Shanghai Jiao Tong University, Shanghai, China, 2010. [Google Scholar]
  24. Ou, X.M.; Zhang, X.L. Fossil Energy Consumption and GHG Emissions of Final Energy by LCA in China. China Soft Sci. 2009, 2, 208–214. [Google Scholar]
  25. SH/T 5000-2011; The Calculation Method of CO2 Emissions in Petrochemical Production. Ministry of Industry and Information Technology: Beijing, China, 2011.
  26. Xiao, Q.F. Scheduling Design for Container Ship along Yangtze River Considering Transshipment and Real-Time Scheduling. Master’s Thesis, Dalian Maritime University, Dalian, China, 2020. [Google Scholar]
  27. Huang, Y. The Optimization of Yangtzi Freshwater Liner Shipping Routes. Master’s Thesis, Shanghai Jiao Tong University, Shanghai, China, 2007. [Google Scholar]
  28. Fan, A.L.; Yang, J.; Yang, L.; Wu, D.; Vladimir, N. A review of ship fuel consumption models. Ocean. Eng. 2022, 264, 112405. [Google Scholar] [CrossRef]
  29. Percic, M.; Vladimir, N.; Fan, A.L. Life-cycle cost assessment of alternative marine fuels to reduce the carbon footprint in short-sea shipping: A case study of Croatia. Appl. Energy 2020, 279, 115848. [Google Scholar] [CrossRef]
  30. Iannaccone, T.; Landucci, G.; Tugnoli, A.; Salzano, E.; Cozzani, V. Sustainability of cruise ship fuel systems: Comparison among LNG and diesel technologies. J. Clean. Prod. 2020, 260, 121069. [Google Scholar] [CrossRef]
  31. IEA. World Energy Outlook 2019; IEA: Paris, France, 2019; Available online: https://www.iea.org/reports/world-energy-outlook-2019?language=zh (accessed on 9 October 2023).
  32. Ng, B.J.H.; Zhou, J.; Giannis, A.; Chang, V.W.-C.; Wang, J.-Y. Environmental life cycle assessment of different domestic wastewater streams: Policy effectiveness in a tropical urban environment. J. Environ. Manag. 2014, 140, 60–68. [Google Scholar] [CrossRef]
Figure 1. (a) Schematic diagram of life cycle of diesel-powered ship; (b) Schematic diagram of life cycle of bio-oil-powered ship.
Figure 1. (a) Schematic diagram of life cycle of diesel-powered ship; (b) Schematic diagram of life cycle of bio-oil-powered ship.
Jmse 12 00226 g001
Figure 2. Anqing–Nanjing section of the Yangtze River.
Figure 2. Anqing–Nanjing section of the Yangtze River.
Jmse 12 00226 g002
Figure 3. CO2 tax prices in different scenarios.
Figure 3. CO2 tax prices in different scenarios.
Jmse 12 00226 g003
Figure 4. The life cycle assessment results of diesel and bio-oil.
Figure 4. The life cycle assessment results of diesel and bio-oil.
Jmse 12 00226 g004
Figure 5. The results of the specific life cycle cost assessment of diesel and bio-oil.
Figure 5. The results of the specific life cycle cost assessment of diesel and bio-oil.
Jmse 12 00226 g005
Figure 6. Sensitivity analysis of carbon tax prices over various time periods.
Figure 6. Sensitivity analysis of carbon tax prices over various time periods.
Jmse 12 00226 g006
Table 1. The transportation parameters of crude oil.
Table 1. The transportation parameters of crude oil.
Transportation ModeRatioAverage Transport Distance, kmEnergy Intensity, KJ/(t·km)Carbon Emission Factor [20], g/MJ
Ocean shipping50.00%11,0002380.38
Train45.00%95024041.12
Pipeline 80.00%50030039.50
Ship10.00%25014875.12
Short-distance vehicle transport0.00%0136274.00
The sum of the transportation mode share exceeds 100%, mainly considering foreign crude oil transportation.
Table 2. The transportation parameters of refined oil products.
Table 2. The transportation parameters of refined oil products.
Transportation ModeRatioAverage Transport Distance, kmEnergy Intensity, kJ/(t·km)Carbon Emission Factor [20], g/MJ
Ocean shipping25.00%70002380.38
Train50.00%90024041.12
Pipeline0.00%16030039.50
Ship15.00%120014875.12
Short-distance vehicle transport10.00%50136274.00
Table 3. Main container ship particulars [26,27].
Table 3. Main container ship particulars [26,27].
Ship TypeJianghai Ship
Net weight of ship (t)1773
Ship loading capacity (TEU)300
Main engine(s) power, PME (kW)2940
Specific fuel consumption, SFC (g/kWh)182
Design speed, Vde (nm/h)11.34
Trip duration, t (h) 16.52
Number of crew (person)16
Ship price (millions)28
Route length, l (nm)165.23
Annual number of round trips, NA122
Lifetime, LT (years)15
Table 4. The emission factors and the global warming potential of greenhouse gases.
Table 4. The emission factors and the global warming potential of greenhouse gases.
Emission Factor (1 g/kg Fuel)
GHGGWPDieselBio-oil
CO2132061360
CH4250.060.0077
N2O2980.150.0043
Table 5. The carbon emissions during operations and the carbon cost of the current policy scenario.
Table 5. The carbon emissions during operations and the carbon cost of the current policy scenario.
PTWA,i (tCO2-eq)The Life Cycle Carbon Emission Cost of Current Policy (Million CNY)
Diesel3849.76069.6013
Bio-oil1933.95254.8233
Disclaimer/Publisher’s Note: The statements, opinions and data contained in all publications are solely those of the individual author(s) and contributor(s) and not of MDPI and/or the editor(s). MDPI and/or the editor(s) disclaim responsibility for any injury to people or property resulting from any ideas, methods, instructions or products referred to in the content.

Share and Cite

MDPI and ACS Style

Li, C.; Zhu, Y.; Zhu, J.; Zhao, Y.; Chen, G. Life Cycle Assessment of Utilizing Bio-Oil to Reduce the Carbon Footprint on the Yangtze River Mainline: A Case Study of Container Ships. J. Mar. Sci. Eng. 2024, 12, 226. https://doi.org/10.3390/jmse12020226

AMA Style

Li C, Zhu Y, Zhu J, Zhao Y, Chen G. Life Cycle Assessment of Utilizing Bio-Oil to Reduce the Carbon Footprint on the Yangtze River Mainline: A Case Study of Container Ships. Journal of Marine Science and Engineering. 2024; 12(2):226. https://doi.org/10.3390/jmse12020226

Chicago/Turabian Style

Li, Chaoran, Yingying Zhu, Jinyuan Zhu, Yifan Zhao, and Geng Chen. 2024. "Life Cycle Assessment of Utilizing Bio-Oil to Reduce the Carbon Footprint on the Yangtze River Mainline: A Case Study of Container Ships" Journal of Marine Science and Engineering 12, no. 2: 226. https://doi.org/10.3390/jmse12020226

Note that from the first issue of 2016, this journal uses article numbers instead of page numbers. See further details here.

Article Metrics

Back to TopTop