# Experimental Investigation of Plow-Chopping Unit

^{1}

^{2}

^{3}

^{4}

^{5}

^{6}

^{*}

## Abstract

**:**

^{2}), changing aperiodically in the frequency range of 0–2.5 Hz, is not accidentally less than the variance of irregularities vibrations of the longitudinal field profile (2.75 cm

^{2}). The plough draft resistant oscillations of the plow-chopping unit had the least impaction at the plowing depth oscillations. The proof of this is the small value of the cross correlation function; for such oscillating processes as ‘plough draft resistance—plowing depth’, it was equal to 0.22, which is 3.4 times less than for oscillating processes ‘surface’s longitudinal profile—plowing depth’. The number of chopped particles less than 15 cm in length increased by 1.5 times, and the number of particles longer than 30 cm decreased by 3 times. With the complete incorporation of plant residues into the soil, their non-chopped part did not exceed 1%.

## 1. Introduction

^{−1}, the range of this indicator oscillations can reach ±30% [9].

^{−1}and even more.

## 2. Material and Method

#### 2.1. Brief Plow-Chopping Unit Performance

#### 2.2. Starting Torque Determination of the Chopper Working Devices

#### 2.3. Main Mode Operation of the Plow-Chopping Unit

^{−1}) and a working range from ±2 g to ±16 g. In this case, the electrical signal enters the Arduino Uno’s analog input and then is transferred to the laptop with a subsequent conversion for processing in the Microsoft Excel environment.

^{−1}).

^{2}and a ruler with a measuring accuracy of ±0.5 cm.

_{1}and the cross-section of the process Y1 (t) when t = t

_{2}.

## 3. Results and Discussion

#### 3.1. Determination of the Operating Mode of the Chopper Plant Residues

#### 3.2. Field Studies of the Plow-Chopping Unit

^{−1}(Figure 10).

^{−1}or 0–2.5 Hz when the operating speed of the plow-chopping unit is 2.0 m·s

^{−1}. Such frequency levels are typical for low-frequency processes, that, in our case, are highly desirable.

^{2}; for fluctuations of the plowing depth, its value is 1.44 cm

^{2}. The difference between these variance values is substantial and nonrandom because, according to the Fisher F-test, the null hypothesis about their equality does not reject a significance level 0.05.

^{2}(Figure 11).

^{2}. The ratio of these variances shows that the true value of the F-test is equal to 1.21. It is less than the F-test’s table value, which for the significance level 0.05, is equal to 1.39. Hence, the null hypothesis of equality of the compared variances is not rejected and both represent the same general sample. Moreover, as follows from the analysis of Figure 11, the frequency composition of vertical oscillations of the tractor’s front axle, both with and without PRR-1.5, is practically the same.

## 4. Conclusions

^{2}, this gain is statistically random and insignificant.

^{2}) is not randomly less than the variance of oscillations of the longitudinal field profile (2.75 cm

^{2}). Even smaller oscillations in the plowing depth depend on fluctuations in the arable-chopping unit’s plow draft resistance.

## Author Contributions

## Funding

## Institutional Review Board Statement

## Informed Consent Statement

## Data Availability Statement

## Conflicts of Interest

## References

- Bulgakov, V.; Adamchuk, V.; Nadykto, V.; Kistechok, O.; Olt, J. Theoretical research into the stability of motion of the ploughing tractor-implement unit operating on the ‘push-pull’ principle. Agron. Res.
**2017**, 15, 1517–1529. [Google Scholar] - Gillund, R.D. Front Mounted Implement. U.S. Patent 4,930,801, 5 June 1990. [Google Scholar]
- Nadykto, V.; Ivanov, S.; Kistechok, O. Investigation of the draft-and-power, and agrotechnical indicators of the work of a ploughing aggregate, created according to the scheme ‘push-pull’. J. Res. Appl. Agric. Eng.
**2017**, 62, 136–139. [Google Scholar] - Thompstone, R.G.; Cowell, P.A. The Influence of Front Linkage Geometry on Tractor-implement Interaction. J. Agric. Eng. Res.
**1990**, 45, 175–186. [Google Scholar] [CrossRef] - Lysych, M.N. A study of the static lateral stability of a tillage machine-tractor unit on a virtual stand. J. Phys. Conf. Ser.
**2020**, 1515, 1–7. [Google Scholar] [CrossRef] - Singh, N.; Pandey, K. Development of Visual Basic Program to Design Front Mounted Three-Point Linkage for Higher Power Tractors. Adv. Res.
**2017**, 11, 1–10. [Google Scholar] [CrossRef] - Singh, N.; Pandey, K.P. Design, Development and Laboratory Testing of a Front Mounted Three Point Linkages for Higher Power Tractors. Int. J. Sci. Environ. Technol.
**2017**, 6, 2087–2099. [Google Scholar] - Persson, S. Mechanics of Cutting Plant Material; American Society of Agricultural Engineers: St. Joseph, MI, USA, 1987; p. 288. [Google Scholar]
- Rotz, C.A.; Muhtar, H.A. Rotary Power Requirements for Harvesting and Handling Equipment. Appl. Eng. Agric.
**1992**, 8, 751–757. [Google Scholar] [CrossRef] - Srivastava, A.K.; Goering, C.E.; Rohrbach, R.P.; Buckmaster, D.R. Engineering Principles of Agricultural Machines; American Society of Agricultural and Biological Engineers: St. Joseph, MI, USA, 2012; p. 559. [Google Scholar]
- Zhang, M.; Sword, M.L.; Buckmaster, D.R.; Cauffman, G.R. Design and Evaluation of a corn Silage Harvester Using Shredding and Flail Cutting. Trans. ASAE
**2003**, 46, 1503–1511. [Google Scholar] [CrossRef] [Green Version] - Dorn, B.; Stadler, M.; Van Der Heijden, M.; Streit, B. Regulation of cover crops and weeds using a roll-chopper for herbicide reduction in no-tillage winter wheat. Soil Tillage Res.
**2013**, 134, 121–132. [Google Scholar] [CrossRef] - Kumhála, F.; Chyba, J.; Pexa, M.; Čedík, J. Measurement of mulcher power input in relation to yield. Agron. Res.
**2016**, 14, 1380–1385. [Google Scholar] - Yisa, M.G.; Terao, H.; Noguchi, N.; Kubota, M. Dynamics of Tractor-implement Combinations on Slopes (Part III): Stability Regions and Optimum Design Parameters. J. Fac. Agric. Hokkaido Univ.
**1998**, 68, 1–17. [Google Scholar] - Kalimullin, M.; Abdrakhmanov, R.; Salimzyanov, M.; Latypov, R. To question of determining design parameters of working body of rotary chopper of tops. Eng. Rural Dev.
**2020**, 19, 1224–1229. [Google Scholar] [CrossRef] - Jia, H.; Wang, L.; Li, C.; Tan, H.; Ma, C. Combined stalk-stubble breaking and mulching machine. Soil Tillage Res.
**2010**, 107, 42–48. [Google Scholar] [CrossRef] - Damanauskas, V.; Velykis, A.; Satkus, A. Efficiency of disc harrow adjustment for stubble tillage quality and fuel consumption. Soil Tillage Res.
**2019**, 194, 104311. [Google Scholar] [CrossRef] - Zhou, H.; Zhang, J.; Xia, J.M.; Tahir, H.; Zhu, Y.; Zhang, C. Effects of subsoiling on working quality and total power consumption of high stubble straw returning machine. Int. J. Agric. Biol. Eng.
**2019**, 12, 56–62. [Google Scholar] [CrossRef] - Qingjie, W.; Hongbo, Z.; Jin, H.; Li, H.; Wanzhi, C.; Xianghong, C.; Rasaily, R.G. Design and experiment of blades-combined no and minimum-till wheat planter under controlled traffic farming system. Trans. Chin. Soc. Agric. Eng.
**2016**, 32, 12–17. [Google Scholar] - Nadykto, V.; Kyurchev, V.; Bulgakov, V.; Findura, P.; Karaiev, O. Influence of the plough with tekrone moldboards and landsides on ploughing parameters. Acta Technol. Agric.
**2020**, 23, 40–45. [Google Scholar] - Kazakevich, P.P. Amelioratory plowing of peat bogs and substantiation of the basic parameters of a double-cut plow. In Proceedings of the National Academy of Sciences of Belarus. Agrarian Series; Publishing House Belorusskaya Nauka: Minsk, Belarus, 2019; pp. 470–480. [Google Scholar] [CrossRef]
- Bulgakov, V.; Adamchuk, V.; Arak, M.; Nadykto, V.; Kyurchev, V.; Olt, J. Theory of vertical oscillations and dynamic stability of combined tractor-implement unit. Agron. Res.
**2016**, 14, 689–710. [Google Scholar]

**Figure 7.**Dynamics torque ${\mathrm{M}}_{\mathrm{pto}}$ at the various operating modes of the tractor’s front PTO: 1–540 rpm; 2–1000 rpm.

**Figure 8.**Speed change of torque ${\mathrm{M}}_{\mathrm{pto}}$ at the various operating modes of the tractor’s front PTO: 1–540 rpm; 2–1000 rpm.

**Figure 9.**Normalized correlation functions of the surface’s longitudinal profile (1) and plowing depth (2) oscillations.

**Figure 10.**Normalized spectral densities of oscillations of the surface’s longitudinal profile (1) and plowing depth (2).

**Figure 11.**Normalized spectral densities of vertical oscillations of tractor’s front axle with (1) and without (2) chopper.

**Figure 12.**Cross correlation functions of plowing depth oscillations from the influence of the surface’s longitudinal profile and plough draft resistance.

Tractor HTZ-16131: Power Engine (kW) | 132.4 |
---|---|

operating mass (kg) | 7800 |

front wheels track (mm) | 2100 |

rear wheels track (mm) | 2100 |

front wheels: tire size | 16.9R38 |

air pressure (bar) | 1.3 |

rear wheels: tire size | 16.9R38 |

air pressure (bar) | 1.1 |

PTO operating mode (rpm) | 540 1000 |

Chopper PRR-1.5: | |

operating mass (kg) | 400 |

working width (m) | 1.70 |

Plough PLN-5-35: | - |

operating mass (kg) | 800 |

plough bottoms number | 5 |

working width (m) | 1.75 |

Index | Value |
---|---|

Soil humidity (%) | 19.9 |

Soil bulk density (g cm^{−3}) | 1.39 |

Height of sunflower stubble (cm) | 43 ± 2 |

Working speed of plow-chopping unit (m s^{−1}) | 2.0 |

Working width of plow-chopping unit (m) | 1.76 |

Plowing depth: mean (cm) | 25.0 |

confidence interval (95%, cm) | 25.0 ± 0.3 |

variance (cm^{2}) | 1.44 |

standard deviation (±cm) | 1.20 |

coefficient of variation (%) | 4.8 |

Plough draft resistance: mean (kN) | 25.2 |

confidence interval (95%, kN) | 25.2 ± 0.6 |

variance (kN^{2}) | 3.61 |

standard deviation (±kN) | 1.90 |

coefficient of variation (%) | 7.5 |

Rpm | Number of Stubble Residues (%) | Total Chopping (%) | ||
---|---|---|---|---|

<15 cm | 15–30 cm | >30 cm | ||

540 | 41.3 | 43.4 | 15.3 | 95.5 |

1000 | 63.5 | 32.7 | 3.8 | 99.0 |

Publisher’s Note: MDPI stays neutral with regard to jurisdictional claims in published maps and institutional affiliations. |

© 2021 by the authors. Licensee MDPI, Basel, Switzerland. This article is an open access article distributed under the terms and conditions of the Creative Commons Attribution (CC BY) license (http://creativecommons.org/licenses/by/4.0/).

## Share and Cite

**MDPI and ACS Style**

Bulgakov, V.; Aboltins, A.; Beloev, H.; Nadykto, V.; Kyurchev, V.; Adamchuk, V.; Kaminskiy, V.
Experimental Investigation of Plow-Chopping Unit. *Agriculture* **2021**, *11*, 30.
https://doi.org/10.3390/agriculture11010030

**AMA Style**

Bulgakov V, Aboltins A, Beloev H, Nadykto V, Kyurchev V, Adamchuk V, Kaminskiy V.
Experimental Investigation of Plow-Chopping Unit. *Agriculture*. 2021; 11(1):30.
https://doi.org/10.3390/agriculture11010030

**Chicago/Turabian Style**

Bulgakov, Volodymyr, Aivars Aboltins, Hristo Beloev, Volodymyr Nadykto, Volodymyr Kyurchev, Valerii Adamchuk, and Viktor Kaminskiy.
2021. "Experimental Investigation of Plow-Chopping Unit" *Agriculture* 11, no. 1: 30.
https://doi.org/10.3390/agriculture11010030