1. Introduction
Relative humidity is an important parameter that determines product quality and process economics in many industrial processes [
1]. Some typical fields of applications are industrial drying, chemical and pharmaceutical industry, production of plastics, flue gas measurement in power plants, agriculture, food processing, heating, ventilation and air conditioning, paper production and coloring of textiles.
One option to measure relative humidity is by means of acoustic techniques. From kinetic gas theory it follows that the speed of sound in air depends on the composition and condition of the air [
2]. The most important parameters that determine the speed of sound in air are: temperature, relative humidity,
CO2 concentration and to a lesser extent absolute pressure. By simultaneous measurement of speed of sound and air temperature, relative humidity can be calculated for given pressure and
CO2 concentration.
Acoustic sensors are non-intrusive, in contrast to other conventional humidity sensors like wet and dry bulb sensors or capacitive sensors. This ensures no pressure loss for in-line applications, high life expectancy and insensitivity to contamination. Another advantage over conventional sensors is the high temperature range. Most important advantage is the high sensitivity and the increase of sensitivity with increasing temperature.
Recently, many studies for humidity sensors have been published, particularly acoustic sensors. However, most of these recent developments in acoustic humidity sensors are based on Surface Acoustic Wave (SAW) sensors, which works with another principle, see the work of Wu
et al. [
3], for example. A comprehensive review on magnetoelastic sensors which can be applied for humidity measurements is given by Grimes
et al. [
4]. The above mentioned conventional and SAW techniques for humidity measurement are local techniques,
i.e., with a measuring volume in the order of one cubic
mm. The acoustic technique of the present paper, on the other hand, yields a chordal beam average of humidity in the desired portion of the duct. Another type of acoustic sensor was developed by Zipser
et al. [
5], which has a different layout and is not in-line. Tsai
et al. uses an ultrasonic sensor for temperature measurement with a correction for humidity [
6].
In the present study, the design and tests of a high accuracy in-line acoustic relative humidity sensor for flowing air-steam mixtures in a duct flow are presented. This includes theory, construction, calibration, considerations on dynamic response and results.
2. Theory
The speed of sound in a gas for which the second virial coefficient,
B, is given, can be calculated from [
2,
7]. In the equation below,
T is in
K:
For each constituent of a gas mixture, γ and B must be known to calculate the speed of sound in the gas mixture. By measuring the speed of sound at constant temperature, T, and pressure, p, determined from measurements of air, the composition of air at constant T and p uniquely depends on the speed of sound.
The constituents of standard dry air according to ISO norm 2533 are listed in
Table 1.
Only the concentrations of N2, O2, Ar, CO2 and Ne and the amount of water vapor have a significant effect on the molar mass of air. If the composition is assumed to be constant except for the amount of water vapor, the mole fraction of water can be determined from the speed of sound.
The use of the second virial coefficient
B of a mixture of gases to calculate humidity,
RH, is examined in [
2]. Much more convenient to use is the following approximate equation:
The coefficients {
ai} are determined by calibration in reference air of known temperature,
T, known humidity,
RH and known speed of sound at the measurement frequency,
c. From 2, the mole fraction of water vapor,
xw, is determined. Relative humidity is then calculated with the aid of:
The saturated vapor pressure of water is calculated from, for example, an Antoine relation [
8]:
Coefficients are A = 8.07131, B = 1730.63, C = 233.426, valid for 1–100 ° C, T in °C and psv in Pa.
The relation between the speed of sound, temperature and relative humidity according to
Equation 2 to
4 is given in
Figure 1. Note that sensitivity for
c increases with increasing temperature and with increasing
RH.
The speed of sound is determined by measuring the ultrasonic transit time of the acoustic signal on a trajectory. The transit time is influenced by the air-steam flow velocity, which is taken into account by averaging the speed of sound in upstream and downstream direction:
with
tm the transit time averaged in
s. Lt is the total length of the acoustic trajectory in
m between transducers
Tr1 and
Tr2, see
Figure 2.
t1 is the transit time in downstream direction and
t2 the transit time in upstream direction in
s.
The average gas flow velocity is determined from the difference in transit time in upstream and downstream direction over the part of the acoustic trajectory
Ls.
Ls is the part of the acoustic trajectory where the ultrasonic waves have a component in the direction of the gas flow (thick outline in
Figure 2). The average transit time is given by:
At a part of the total acoustic trajectory,
Lt, the acoustic trajectory is perpendicular or outside the main flow. Gas flow velocity has no effect on the transit time here. This part of the trajectory is
Ld:
The average transit time over trajectory
Ld is then given by:
Transit times in downstream and upstream direction over trajectory
Ls are:
Due to superposition of the speed of sound on the gas flow velocity over trajectory
Ls, transit times in downstream and upstream direction are:
with
α the angle between flow direction and the acoustic trajectory
Ls, see
Figure 2. Rearranging 10 and eliminating the speed of sound results in an average gas flow velocity of:
Equation 11 allows determination of the average gas velocity from known dimensions (trajectory length and angle) and measured values (transit times) only, without the need of parameters of the gas which affect
c.
2.1. Sensitivity and Accuracy
The main advantages of the acoustic humidity sensor become clear by observing the sensitivity of the relative humidity measurement on temperature. Relative humidity is determined by separate, but instantaneous, speed of sound and temperature measurements. Sensitivity of relative humidity is then given by:
The equation above is graphically represented by
Figure 3. Relative humidity is very dependent on temperature. The accuracy of the relative humidity measurement is dominated by the accuracy of the independent temperature measurement.
In practice, accuracy is limited to the accuracy of reference relative humidity sensors at calibration. At temperatures below 50 °C, a small error in temperature results in large errors in humidity measurement. However, in the range of 50–100 °C very accurate humidity measurements over the full range of 0–100 %
RH are possible, given a typical temperature measurement accuracy of ± 0.1 °C. This in contrast to other popular relative humidity measurement techniques like capacitive humidity sensors which become less accurate at high humidity and temperature levels [
1], typically far worse than 2 %
RH above 80 °C. Moreover, at constant temperature, variations in relative humidity can be measured very fast, at about 100
Hz, because the response time mainly depends on the speed of sound and typical transit times of the acoustic trajectory. Other popular relative humidity measurement techniques like capacitive humidity sensors suffer from response times in the order of seconds, depending on gas flow velocity. Although
CO2-concentration and pressure also affect speed of sound, thus the relative humidity, these influences are negligible for
CO2 in the
ppm range and for pressures from 75 to 105
kPa [
2].
4. Calibration
Temperature sensors are calibrated from 0 to 100 °C with an insulated Julabo MP open bath circulator and a reference thermometer. Accuracy of each SMT sensor is 0.14 °C. To take possible temperature gradients into account, temperatures are averaged over the height and weighed by the corresponding mass velocity [
9]. Accuracy of the averaged temperature over four sensors is 0.07 °C. Details on calibration of the temperature sensors are given in [
10].
The length of the acoustic trajectory is calibrated by measuring the transit times at no flow conditions for given temperature and relative humidity in an insulated reference box. c is known and transit times t1 and t2 should be equal. Lt is found to be 502.8 ± 0.1 mm. Ls is determined by the design of the measurement device and is found to be 260.0 ± 0.1 mm.
The average gas flow velocity is calibrated over a range of 0 to 12
m/s to 0.13
m/s accurate in a wind tunnel with a reference flow meter [
11].
Relative humidity measurements are calibrated in a Weiss SB22-300 climate chamber with a Michell S4000 cooled mirror optical dewpoint hygrometer, accurate to ±1 %
RH and a psychrometer better than 3 %
RH accurate. Calibration is performed at ambient pressure. A field of 40 measurements is assessed: temperatures from 20.0 to 90.0 °C in steps of 10.0 °C at relative humidities of 10 to 90 % in steps of 20 %. This results in coefficients of
Equation 2 as given in
Table 2. Comparison between the calibration points and the approximation by
Equation 2 with the coefficients of
Table 2 is shown in
Figure 5.
7. Conclusions
In this study, an in-line acoustic relative humidity sensor for air-steam mixtures in duct flow has been designed. The measurement device is capable of measuring line averaged gas velocity, temperature and humidity instantaneously by applying two ultrasonic transducers and an array of four SMT temperature sensors. Measurement range is gas velocity of 0–12
m/s, 0–100 °C and 0–100% relative humidity at ambient pressure. Main advantage over conventional humidity sensors is the high sensitivity at high
RH at temperatures exceeding 50 °C, with accuracy increasing with increasing temperature. The sensors are non-intrusive and resist highly humid environments. Accuracy for line averaged flow velocity is 0.13
m/s, average temperature 0.07 °C after calibration. With this temperature measurement accuracy, intrinsic accuracy of relative humidity is better than 2 %
RH above 50 °C and within 1 %
RH from 70 to 100 °C. The practical accuracy in relative humidity at constant temperature solely depends on the the humidity calibration with the cooled mirror optical dewpoint hygrometer and a psychrometer, which is typically 1 to 3 %
RH best practice, respectively [
1]. Preliminary tests at the test section inlet of a wind tunnel for condensing heat exchangers have shown improved accuracy in the measurement of the energy balance.