Search Results (148)

Indium-based oxide semiconductors have been commercialized because of their excellent electrical properties, but the high cost, limited availability, and environmental toxicity of indium necessitate the development of alternative materials. Among the most promising candidates, zinc–tin oxide (ZTO) is an indium-free oxide semiconductor with considerable potential, but its relatively low carrier mobility and inherent limitations in thin-film quality demand further performance enhancements. This paper proposes a new approach to overcome these challenges by incorporating single-walled carbon nanotubes (SWNTs) as conductive fillers into the ZTO matrix and using a layer-by-layer multiple coating process to construct nanocomposite thin films. As a result, ZTO/SWNTs (0.07 wt.%) thin-film transistors (TFTs) fabricated with three coating cycles exhibited a high saturation mobility of 18.72 cm²/V·s, a threshold voltage of 0.84 V, and a subthreshold swing of 0.51 V/dec. These values represent an approximately four-fold improvement in mobility compared to ZTO TFT, showing that the multiple-coating-based nanocomposite strategy can effectively overcome the fundamental limitations. This study confirms the feasibility of achieving high-performance oxide semiconductor transistors without indium, providing a sustainable pathway for next-generation flexible electronics and display technologies. Full article

This study investigates the development and sensing profile of synthetic melanin nanoparticle-coated electrodes for the electrochemical detection of heavy metals, including lead (Pb), cadmium (Cd), cobalt (Co), zinc (Zn), nickel (Ni), and iron (Fe). Synthetic melanin films were prepared in situ by the deacetylation of diacetoxy indole (DAI) to dihydroxy indole (DHI), followed by the deposition of DHI monomers onto indium tin oxide (ITO) and glassy carbon electrodes (GCE) using cyclic voltammetry (CV), forming a thin layer of synthetic melanin film. The deposition process was characterized by electrochemical quartz crystal microbalance (EQCM) in combination with linear sweep voltammetry (LSV) and amperometry to determine the mass and thickness of the deposited film. Surface morphology and elemental composition were examined using scanning electron microscopy (SEM) and energy-dispersive X-ray spectroscopy (EDX). In contrast, Fourier-transform infrared (FTIR) and UV–Vis spectroscopy confirmed the melanin’s chemical structure and its polyphenolic functional groups. Differential pulse voltammetry (DPV) and amperometry were employed to evaluate the melanin films’ electrochemical activity and sensitivity for detecting heavy metal ions. Reproducibility and repeatability were rigorously assessed, showing consistent electrochemical performance across multiple electrodes and trials. A comparative analysis of ITO, GCE, and graphite electrodes was conducted to identify the most suitable substrate for melanin film preparation, focusing on stability, electrochemical response, and metal ion sensing efficiency. Finally, the applicability of melanin-coated electrodes was tested on in-house heavy metal water samples, exploring their potential for practical environmental monitoring of toxic heavy metals. The findings highlight synthetic melanin-coated electrodes as a promising platform for sensitive and reliable detection of iron with a sensitivity of 106 nA/ppm and a limit of quantification as low as 1 ppm. Full article

The aim of this work was to estimate the impact of polypropylene (BOPP) films with active coatings applied on their surface on the quality of sliced, plant-based meat analogue (PBMA) sausages. The coatings contained zinc oxide nanoparticles and geraniol (AG) or zinc oxide and carvacrol (AC) as active compounds. The outcomes of the study indicated that the total microbial count of ready-to-eat, sliced PBMAs bought from a local store was high, confirming that the plant-based sausage must have been contaminated during slicing. It was shown that BOPP bags and spacers covered with the AG layer reduced the number of mesophilic bacteria in sliced plant-based sausages stored for 96 h, proving that this packaging material maintained the microbial quality of PBMA samples. It has to be underlined that neither S. aureus, L. monocytogenes, Salmonella sp. nor coliform bacteria were detected in the plant sausage samples after 48 h and 96 h of storage in the BOPP packaging covered with the AG and AC coatings, confirming that these slices were acceptable for consumption. However, the textural analysis showed that bags coated with the AC layer were the best bags for 96 h of storage. Full article

Magnesium-based alloys are considered to be promising materials for the fabrication of temporary bone repair medical implants. The AZ31 magnesium-based (AZ31-Mg) alloy contains 3% aluminum and 1% zinc in its microstructure, which gives it mechanical strength and corrosion resistance. Nonetheless, the corrosion rate is high, which can lead to implant failure due to rapid degradation, which triggers the release of harmful metal ions. In the present work, a passive layer was obtained on the AZ31-Mg alloy, and subsequently, a cerium oxide (CeO₂) coating was deposited through a chemical conversion treatment using 0.01 M CeO₂ as a precursor. Based on X-ray photoelectron spectroscopy, the calculated amount of Ce(IV) and Ce(III) present in AZ31-Mg(OH)₂/CeO₂ was 93.6% and 6.4%, respectively. AZ31-Mg(OH)₂/CeO₂ showed improved corrosion resistance compared with the bare sample. The in vitro assessment of MC3T3-E1 pre-osteoblast cell viability showed that AZ31-Mg(OH)₂/CeO₂ was biocompatible after incubation for 24 and 72 h. The results revealed that the CeO₂ coating confers greater electrochemical stability and biocompatibility properties, mostly due to the presence of Ce⁴⁺ ions. Full article

The present study employed the spin-coating method for the preparation of nanostructured crystalline zinc oxide (ZnO) thin films on FTO glass substrates. Subsequently, cadmium selenide (CdSe) layers were deposited on the surfaces using two distinct chemical methods: successive ionic layer adsorption and reaction (SILAR) and chemical bath deposition (CBD). The obtained films were then characterized by a variety of analytical methods, including XRD, SEM, AFM, EDX spectroscopy, UV–vis spectrophotometry, and linear sweep voltammetry. The XRD and SEM studies demonstrated that all of the films exhibited a polycrystalline nature, with the crystallinity of the cadmium selenide thin films prepared using the SILAR method exceeding that obtained by the CBD method. The SEM and AFM images revealed the uniformity of the cadmium selenide films on the FTO substrates, with no visible cracks or pores. The EDX spectra confirmed the presence of the expected elements in the thin films. The optical band gaps (E_g) for CdSe prepared with the SILAR or CBD method were determined to be 1.85 and 1.97 eV, respectively. Full article

This study addresses the challenges of efficient, large-scale production of flexible transparent conducting electrodes (TCEs). We fabricate TCEs on polyethylene terephthalate (PET) substrates using a high-speed roll-to-roll (R2R) compatible method that combines gravure printing and photonic curing. The hybrid TCEs consist of Ag metal bus lines (Ag MBLs) coated with silver nanowires (AgNWs) and indium zinc oxide (IZO) layers. All materials are solutions deposited at speeds exceeding 10 m/min using gravure printing. We conduct a systematic study to optimize coating parameters and tune solvent composition to achieve a uniform AgNW network. The entire stack undergoes photonic curing, a low-energy annealing method that can be completed at high speeds and will not damage the plastic substrates. The resulting hybrid TCEs exhibit a transmittance of 92% averaged from 400 nm to 1100 nm and a sheet resistance of 11 Ω/sq. Mechanical durability is tested by bending the hybrid TCEs to a strain of 1% for 2000 cycles. The results show a minimal increase (<5%) in resistance. The high-throughput potential is established by showing that each hybrid TCE fabrication step can be completed at 30 m/min. We further fabricate methylammonium lead iodide solar cells to demonstrate the practical use of these TCEs, achieving an average power conversion efficiency (PCE) of 13%. The high-performance hybrid TCEs produced using R2R-compatible processes show potential as a viable choice for replacing vacuum-deposited indium tin oxide films on PET. Full article

Different materials are studied for environmental gas sensors as well as photodetection prototypes. A ZnO/MoS₂ p-n junction was synthetized to act as a multifunctional sensor prototype. After the ZnO was prepared on a silicon substrate by using DC sputtering at room temperature, molybdenum disulfide layers were spin-coated on a nanostructured zinc oxide flake-shaped surface to form an active layer. The heterostructure’s composite surface was examined using scanning electron microscopy, energy-dispersed X-ray, and Raman spectroscopy. Responses to light frequencies, light intensities, and gas chemical tracing were characterized, revealing an enhanced multifunctional performance of the prototype. Characterizations of light-induced photocurrents indicted that the obtained response strength (photocurrent/illumination light power) was up to 0.01 A/W, and the response time was less than 5 ms. In contrast, the gas-sensing measurements showed that its response strength (variation in resistance/original resistance) was up to 3.7% and the response time was down to 150 s when the prototype was exposed to ammonia gas, with the concentration down to 168 ppm. The fabricated prototype appears to have high stability and reproducibility, quick response and recovery times, as well as a high signal-to-noise ratio. Full article

This article compares two new textile materials used to clean up spills of oil or two oil products (crude oil, diesel fuel, and base oil SN 150). The plain-woven cotton fabric is hydrophilic, with a typical porous structure. After coating with a layer of chitosan modified with benzaldehyde and cross-linked with glutaraldehyde (CB), its hydrophobicity increases, hence the sorption affinity to hydrophobic hydrocarbons. Including in situ synthesized zinc oxide particles in the hydrophobic chitosan layer (CBZ) changes its structure and increases the sorption capacity. The morphology of the layers was assessed using scanning electron microscopy (SEM) and by comparing the contact angles of the pollutants against the cotton fabric and the composite materials. EDX analysis and mapping for the Zn element show that zinc is homogeneously distributed on the fabric surface. The roughness enhancement and mesoporous structure under the influence of zinc oxide particles were established by the Brunauer Emmett Teller (BET) method and atomic force microscopy (AFM). The advantages of textile composites are their flexibility, stability, and ability to float on the water and wipe up oil spills. It was found that the materials can be successfully regenerated and used repeatedly, making them highly effective because the sorbed crude oil or petroleum products can be separated and utilized. Full article

The challenging wind conditions surrounding power transmission lines exacerbate the wear and corrosion of transmission line fittings. Thermal diffusion galvanizing technology, a novel method for obtaining galvanizing layers, significantly enhances the wear and corrosion resistance of metal components, thereby extending their service life. Holding temperature plays a critical role in determining the performance of the thermally diffused zinc coating. In this study, we prepared thermally diffused zinc coatings containing rare earth oxides on 35CrMo steel at various holding temperatures and evaluated their morphology, wear resistance, and corrosion resistance. The findings indicate that increasing the holding temperature enhances the diffusion of zinc and iron, yielding thicker coatings with a maximum thickness of 60 μm at a holding temperature of 450 °C. Notably, the zinc coating produced at a holding temperature of 410 °C exhibits optimal wear resistance at room temperature, and the wear failure mechanisms were predominantly abrasive wear and oxidative wear with slight adhesive wear. In addition, the zinc coating produced at a holding temperature of 430 °C exhibits optimal corrosion resistance at room temperature. Full article

Zinc–tin oxide (ZTO) thin films (ZnO)_x(SnO₂)_1−x with different material composition x (0 < x < 1) are deposited by spin coating on glass substrates at room temperature. The Differential Scanning Calorimetry (DSC) data of the precursor compounds show gradual phase transitions up to 480 °C. These data are used for an appropriate regime for thermal annealing of the layers. X-ray photoelectron spectroscopy (XPS) data show mixed oxide compound formation in states Zn²⁺, Sn⁴⁺ and O²⁻ of the constituents. Optical investigation manifests high transmittance above 80% in the visible spectral range and an optical band gap of 3.3–3.7 eV. The work functions vary between 4.1 eV and 5 eV, depending on the annealing, with deviations less than 1% for surface 1 mm² scans. Stack devices ITO/ZTO/metal with different metal contacts are formed. The I–V (current–voltage) measurements of the fabricated stacks exhibit Ohmic or nonlinear behavior, depending on the material composition and the work function levels. Full article

Infections continue to pose significant challenges in dentistry, necessitating the development of innovative solutions that can effectively address these issues. This study focuses on creating coatings made from polymethyl methacrylate (PMMA) enriched with zinc oxide–silver composite nanoparticles, layered to Ti6Al4V–titanium alloy substrates. The application of these materials aims to create a solution for the abutments utilized in complete dental implant systems, representing the area most susceptible to bacterial infections. The nanoparticles were synthesized using a hydrothermal method, optimized through specific temperature and pressure parameters to achieve effective morphologies and sizes that enhance antibacterial efficacy. The layers were applied to the titanium substrate using the spin coating technique, chosen for its advantages and compatibility with the materials involved. Comprehensive analyses were conducted on the antimicrobial powders, including X-ray diffraction, Fourier transform infrared spectroscopy, scanning electron microscopy, and energy-dispersive X-ray spectroscopy. Furthermore, the PMMA-based coatings incorporating antimicrobial nanoparticles were evaluated to ensure uniformity and homogeneity across the titanium alloy surface by IR mapping and SBF immersion–SEM analysis. The antimicrobial activity of the samples was demonstrated with impressive results against Staphylococcus aureus, Pseudomonas aeruginosa, and Candida albicans, as assessed through biofilm modulation studies. The biocompatibility of the samples was validated through in vitro cell-based assays, which demonstrated excellent compatibility between PMMA-based coatings and human preosteoblasts, confirming their potential suitability for future use in dental implants. Full article

Throughout millions of years of biological evolution, shell structures have developed a highly complex layered organic–inorganic structure that makes them effective against a wide range of external impacts, including mechanical stress and chemical corrosion. Therefore, shell-like biomimetic materials are considered to possess high strength and toughness. Nevertheless, although shell structures have exhibited superior performance across multiple domains, understanding of their structural complexities and corrosion protection mechanisms remains relatively limited within the scope of human knowledge. In this study, alternating ZnO–graphene/epoxy coatings featuring shell-like structures were synthesized, and their anticorrosion properties were evaluated through the incorporation of ZnO to enhance the dispersion of graphene. Electrochemical impedance spectroscopy (EIS) tests showed that with an increased number of ZnO–graphene layers, the coating resistance of the bionic composite coating also increased: from 8.21 × 10⁷ Ω·cm² of the pure epoxy coating to 7.64 × 10⁸ Ω cm². The composite coating, comprising three alternating layers of zinc oxide and four layers of epoxy resin, exhibited an electrochemical impedance two orders of magnitude greater than that of pure epoxy resin following immersion in a 3.5% sodium chloride solution, demonstrating excellent corrosion resistance. The results showed that with increased ZnO–graphene layers, ZnO–graphene disperses more uniformly in water and has greater rigidity. Full article

Black nickel coatings are pursued for both decorative purposes and advanced applications, including solar collectors, space technologies, and optical devices. The term “black nickel” typically refers not only to nickel but also to nickel alloys that can exhibit the characteristic black coloration, either bright or matte. This review provides an in-depth look at various techniques for producing black nickel coatings, focusing on both electrodeposition and electroless deposition methods. The discussion covers the different bath compositions and deposition conditions used to achieve the distinctive black color. The origins of black coloration in electrodeposited nickel and its alloys are shown in detail, emphasizing the crucial role of bath components and the formation of black compounds such as oxides, sulfides, and/or the nickel–zinc intermetallic compound. This review also highlights the necessity of oxidizing acid etching to blacken Ni–P electroless deposits, leading to the formation of a thin layer of black nickel oxides on a porous surface. The key properties of black nickel coatings are discussed, along with their relevance for various practical applications. Full article

Photodetectors and gas sensors are vital in modern technology, spanning from environmental monitoring to biomedical diagnostics. This paper explores the UV detection and gas sensing properties of a zinc oxide (ZnO) nanorod array (ZNA) grown on silver nanowire mesh (AgNM) using a hydrothermal method. We examined the impact of different zinc acetate precursor concentrations on their properties. Results show the AgNM forms a network with high transparency (79%) and low sheet resistance (7.23 Ω/□). A sol–gel ZnO thin film was coated on this mesh, providing a seed layer with a hexagonal wurtzite structure. Increasing the precursor concentration alters the diameter, length, and area density of ZNAs, affecting their performance. The ZNA-AgNM-based photodetector shows enhanced dark current and photocurrent with increasing precursor concentration, achieving a maximum photoresponsivity of 114 A/W at 374 nm and a detectivity of 6.37 × 10¹⁴ Jones at 0.05 M zinc acetate. For gas sensing, the resistance of ZNA-AgNM-based sensors decreases with temperature, with the best hydrogen response (2.71) at 300 °C and 0.04 M precursor concentration. These findings highlight the potential of ZNA-AgNM for high-performance UV photodetectors and hydrogen gas sensors, offering an alternative way for the development of future sensing devices with enhanced performance and functionality. Full article

In this work, bismuth sulfide (Bi₂S₃) thin films were deposited by a chemical bath deposition (CBD) technique (called soft chemistry), while titanium dioxide (TiO₂) nanoparticles were synthesized by sol–gel and zinc oxide (ZnO) nanoparticles were extracted from alkaline batteries. The resulting nanoparticles were then deposited on the Bi₂S₃ thin films by spin coating at 1000 rpm for 60 s each layer to create heterojunctions of Bi₂S₃/ZnO and Bi₂S₃/TiO₂. These materials were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), and energy dispersive X-ray spectroscopy (EDX). The optical and contact angle analyses were undertaken by UV–Vis spectroscopy and a contact microscopy angle meter, respectively. The calculated band gap values were found to be between 1.9 eV and 2.45 eV. The Bi₂S₃ presented an orthorhombic structure, the TiO₂ nanoparticles presented an anatase structure, and the ZnO nanoparticles presented a wurtzite hexagonal crystal structure. Furthermore, heterogeneous solar photocatalysis was performed using the Bi₂S₃, Bi₂S₃/ZnO, and Bi₂S₃/TiO₂ thin film combinations, which resulted in the degradation of Congo red increasing from 8.89% to 30.80% after a 30 min exposure to sunlight. Full article