Search Results (6)

Accurate real-time temperature measurement under extreme thermal-pressure conditions remains challenging in aerospace. Sapphire fiber Bragg gratings (FBGs), exhibiting temperature measurement capabilities up to 1900 °C, demonstrate suitability for such extreme environments. However, the development of a high-performance demodulation system capable of processing sapphire FBG signals over wide spectral ranges at elevated speeds remains a technical challenge. This study presents a real-time FBG signal demodulation system that incorporates an all-dielectric subwavelength grating edge filter. The designed grating, comprising a TiO₂/Si₃N₄ subwavelength unit array, modulates Mie-type electric and magnetic multipole resonances to achieve precisely tailored transmission and reflection spectra. Simulation results indicate that the grating exhibits low ohmic loss, excellent linearity, complementary transmission/reflection characteristics, a wide linear range, and angular-dependent tunability. The designed edge-filter-based demodulation system incorporates dual single-point detectors to simultaneously monitor the transmitted and reflected signals. Leveraging the functional relationship between the center wavelength of the FBG and the detected signals, this system enables high-speed, wide-range interrogation of the center wavelength, thus facilitating real-time demodulation for wide-range temperature sensing. The proposed method and system are validated through theoretical modeling, offering an innovative approach for sapphire FBG signal demodulation under extreme thermal-pressure conditions. Full article

The paper presents the application of the acousto-optic tunable filter (AOTF) in surface plasmon resonance (SPR) spectroscopy to measure the optical thickness of thin dielectric coatings. The technique presented uses combined angular and spectral interrogation modes to obtain the reflection coefficient under the condition of SPR. Surface electromagnetic waves were excited in the Kretschmann geometry, with the AOTF serving as a monochromator and polarizer of light from a white broadband radiation source. The experiments highlighted the high sensitivity of the method and the lower amount of noise in the resonance curves compared with the laser light source. This optical technique can be implemented for nondestructive testing in the production of thin films in not only the visible, but also the infrared and terahertz ranges. Full article

In this paper, the thermal stability of a Bloch Surface Wave (BSW) assisted bio-photonic sensor is investigated. The structural analysis is carried out using the transfer matrix method (TMM). The design comprises a truncated one-dimensional photonic crystal (1D-PhC) structure along with a defective top layer. The structural parameters are optimized to excite a BSW at the top interface for an operating wavelength of 632.8 nm. The mode confinement is confirmed by using wavelength interrogation, angular interrogation and surface electric field profile. Further, the effect of thermal variation on BSW excitation angle and sensitivity is carried out. The analysis shows the average variations in excitation angle and sensitivity of about −0.00096 degree/$°\mathrm{C}$ and 0.01046 (degree/RIU)/$°\mathrm{C}$, respectively. Additionally, the analysis is also extended towards different lower wavelengths of 400 nm and 550 nm, which provides average variations in the excitation angles of about −0.0027 degree/$°\mathrm{C}$, and 0.0016 degree/$°\mathrm{C}$. This shows that the structural sensitivity response is more thermally stable at the lower wavelength range. Thus, showing its potential applications in designing thermally stable bio-photonic sensors. Full article

This paper describes a compact refractometer in visible with optical bounds states in the continuum (BICs) using silicon nitride (Si₃N₄) based sub-wavelength medium contrast gratings (MCGs). The proposed device is highly sensitive to different polarization states of light and allows a wide dynamic range from 1.330 (aqueous environment) to 1.420 (biomolecules) monitoring, apart from its being thermally stable. The proposed sensor has a sensitivity of 363 nm/RIU for X polarized light and 137 nm/RIU for Y polarized light. The spectral characteristics have been obtained with a high angular resolution for the smaller angle of incidence, which confirms the BIC hybrid modes with good quality factors and enhanced field confinement. The device is based on a normal-to-the-surface optical launching strategy to achieve exceptional interrogation stability and alignment-free performance. This system can also be used in the CMOS photodetectors for on-chip label-free biosensing. Full article

In this paper, we report the development of a portable energy-efficient interrogator (Perrogator) for wavelength-based optical sensors. The interrogator is based on a compact solution encompassing a white light source and the spectral convolution between the sensor and a tunable filter, which is acquired by a photodetector, where a microcontroller has two functions: (i) To control the filter tuning and to (ii) acquire the photodetector signal. Then, the data is sent to a single-board computer for further signal processing. Furthermore, the employed single-board computer has a Wi-Fi module, which can be used to send the sensors data to the cloud. The proposed approach resulted in an interrogator with a resolution as high as 3.82 pm (for 15.64 nm sweeping range) and maximum acquisition frequency of about 210 Hz (with lower resolution ~15.30 pm). Perrogator was compared with a commercial fiber Bragg grating (FBG) interrogator for strain measurements and good agreement between both devices was found (1.226 pm/µε for the commercial interrogator and 1.201 pm/µε for the proposed approach with root mean square error of 0.0144 and 0.0153, respectively), where the Perrogator has the additional advantages of lower cost, higher portability and lower energy consumption. In order to demonstrate such advantages in conjunction with the high acquisition frequency allowed us to demonstrate two wearable applications using the proposed interrogation device over FBG and Fabry-Perot interferometer (FPI) sensors. In the first application, an FBG-embedded smart textile for knee angle assessment was used to analyze the gait of a healthy person. Due to the capability of reconstructing the FBG spectra, it was possible to employ a technique based on the FBG wavelength shift and reflectivity to decouple the effects of the bending angle and axial strain on the FBG response. The measurement of the knee angle as well as the estimation of the angular and axial displacements on the grating that can be correlated to the variations of the knee center of rotation were performed. In the second application, a FPI was embedded in a chest band for simultaneous measurement of breath and heart rates, where good agreement (error below 5%) was found with the reference sensors in all analyzed cases. Full article

Nanocavity resonators in metals acting as nanofluidic refractive-index sensors were analyzed theoretically. With the illumination of transverse electric polarized light, the proposed refractive index sensor structure acts as a pure electromagnetic resonator without the excitation of surface plasmons. The reflected signal from the nanocavity resonators can be very sensitive to the refractive index of the fluids inside the nanocavities due to the enhancement of the electric field of the resonant mode inside the cavities. Such a sensor configuration can be a useful tool for probing the refractive index change of the fluid inside the nanocavities using the spectral, angular or intensity interrogation schemes. The wavelength sensitivity of 430 nm/RIU, angular sensitivity of 200–1,000 deg/RIU and intensity sensitivity of 25.5 RIU⁻¹ can be achieved in the proposed sensor configuration. Full article