Search Results (98)

Freezing and thawing cycles significantly affect the mechanical and hydraulic behavior of soils, posing detrimental challenges for infrastructures in cold climates. This study develops and validates a coupled Thermal–Hydraulic–Mechanical (THM) model using COMSOL Multiphysics (Version 6.3) to demonstrate the complexities of vapor and water flux, heat transport, frost heave, and vertical stress build-up in unsaturated soils. The analysis focuses on fine sand, sandy clay, and silty clay by examining their varying susceptibilities to frost action. Silty clay generated the highest amount of frost heave and steepest vertical stress gradients due to its high-water retention and strong capillary forces. Fine sand, on the other hand, produced a minimal amount of frost heave and a polarized vertical stress distribution. The study also revealed that vapor flux is more noticeable in freezing fine sand, while silty clay produces the greatest water flux between the frozen and unfrozen zones. The study also assesses the impact of soil properties including the saturated hydraulic conductivity, the particle thermal conductivity, and particle heat capacity on the frost-induced phenomena. Findings show that reducing the saturated hydraulic conductivity has a greater impact on mitigating frost heave than other variations in thermal properties. Silty clay is most affected by these changes, particularly near the soil surface, while fine sand shows less noticeable responses. Full article

Transpiration cooling that utilizes the phase change of a liquid coolant is recognized as an effective thermal protection technique for extreme environments. However, the introduction of phase change within the porous structure brings about challenges, such as vapor blockage, pressure fluctuations, and temperature inversion, which critically influence system reliability. This study conducts numerical analyses of coupled processes of heat transfer, flow, and phase change in transpiration cooling using a Two-Phase Mixture Model. The simulation incorporates a Local Thermal Non-Equilibrium approach to capture the distinct temperature fields of the solid and fluid phases, enabling accurate prediction of the thermal response within two-phase and single-phase regions. The results reveal that under low heat flux, dominant capillary action suppresses dry-out and expands the two-phase region. Conversely, high heat flux causes vaporization to overwhelm the capillary supply, forming a superheated vapor layer and constricting the two-phase zone. The analysis also explains a paradoxical pressure drop, where an initial increase in flow rate reduces pressure loss by suppressing the high-viscosity vapor phase. Furthermore, a local temperature inversion, where the fluid becomes hotter than the solid matrix, is identified and attributed to vapor counterflow and its subsequent condensation. Full article

The development of effective oil adsorbents has attracted a great deal of attention due to the increasingly serious problem of oil pollution. A light and porous collagen (COL)/polyvinyl alcohol (PVA)/vanadium carbide (V₂CT_x) composite aerogel was synthesized using a simple method of blending, directional freezing, and drying. After modification with methyltriethoxysilane (MTMS) via chemical vapor deposition, the aerogel possessed an excellent hydrophobicity and its water contact angle reached 135°. The hydrophobic COL/PVA/V₂CT_x composite aerogel exhibits a porous structure with a specific surface area of 49 m²/g. It also possesses prominent mechanical properties with an 80.5 kPa compressive stress at 70% strain, a low density (about 28 mg/cm³), and outstanding thermal stability, demonstrating a 61.02% weight loss from 208 °C to 550 °C. Importantly, the hydrophobic COL/PVA/V₂CT_x aerogel exhibits a higher oil absorption capacity and stability, as well as a faster absorption rate, than the COL/PVA aerogel when tested with various oils. The hydrophobic COL/PVA/V₂CT_x aerogel has the capacity to adsorb 80 times its own weight of methylene chloride, with help from hydrophobic interactions, Van der Waals forces, intermolecular interactions, and capillary action. Compared with the pseudo first-order model, the pseudo second-order model is more suitable for oil adsorption kinetics. Therefore, the hydrophobic COL/PVA/V₂CT_x aerogel can be used as an environmentally friendly and efficient oil adsorbent. Full article

The escalating heat flux densities in high-performance electronics necessitate superior thermal management. This study enhanced pool-boiling heat transfer, a method offering high heat removal capacity, by leveraging Binder Jetting 3D Printing (BJ3DP) to create complex porous copper structures without the need for chemical treatments. This approach enables a reliable utilization of phenomena like capillarity for improved performance. Three types of porous copper structures, namely Large Lattice, Small Lattice, and Staggered, were fabricated on pure copper substrates and tested via pool boiling of de-ionized and de-gassed water at atmospheric pressure. Compared to a plain polished copper surface, which exhibited a critical heat flux (CHF) of 782 kW/m² at a wall superheat of 18 K, the 3D-printed porous copper surfaces showed significantly improved heat transfer performance. The Staggered surface achieved a conventional CHF of 2342.4 kW/m² (a 199.7% enhancement) at a wall superheat of 24.6 K. Notably, the Large Lattice and Small Lattice structures demonstrated exceptionally stable boiling without reaching the typical catastrophic CHF within the experimental parameters. These geometries continued to increase in heat flux, reaching maximums of 2397.7 kW/m² (206.8% higher at a wall superheat of 55.6 K) and 2577.2 kW/m² (229.7% higher at a wall superheat of 39.5 K), respectively. Subsequently, a gradual decline in heat flux was observed with an increasing wall superheat, demonstrating an outstanding resistance to the boiling crisis. These improvements are attributed to the formation of distinct vapor–liquid pathways within the porous structures, which promotes the efficient rewetting of the heated surface through capillary action. This mechanism supports a highly efficient, self-sustaining boiling configuration, emphasizing the superior rewetting and vapor management capabilities of these 3D-printed porous structures, which extend the boundaries of sustained high heat flux performance. The porous surfaces also demonstrated a higher heat transfer coefficient (HTC), particularly at lower heat fluxes (≤750 kW/m²). High-speed digital camera visualization provided further insight into the boiling phenomenon. Overall, the findings demonstrate that these BJ3DP structured surfaces produce optimized vapor–liquid pathways and capillary-enhanced rewetting, offering significantly superior heat transfer performance compared to smooth surfaces and highlighting their potential for advanced thermal management. Full article

Earth materials in construction demonstrate significant potential attributed to their accessibility, recyclability, and low energy demands for processing. Modern techniques have enhanced their mechanical strength and durability, enabling their application in load-bearing and infill walls while preserving ecological benefits. However, existing studies on indoor heat–humidity regulation primarily emphasize material parameters and macro-level performance. Moreover, the dynamic interactions between the unique thermal storage–release mechanisms and indoor environments have not been systematically analyzed. With the Kelvin equation, capillary mechanics, adsorption theories, and microstructural analysis were integrated in this study to quantify cyclic capillary condensation and evaporation in microvoids. The results reveal that earth materials contain abundant medium-sized pores (19.85–53.83 nm) sustaining vapor exchange with their surroundings. Capillary condensation occurs 0.86–0.96 times the planar surface vapor pressure, influenced by pore size (negatively correlated) and temperature (negatively correlated). During the daytime, capillary evaporation occurs in the nanopores of the raw earth wall under the influence of the outdoor environment’s cyclical temperature and humidity. This process absorbs heat from the indoor environment and raises the ambient humidity. During the nighttime, capillary condensation occurs in the pores, releasing heat to the indoor area and absorbing moisture from the environment, contributing to the balance of the indoor thermal environment of the earth buildings. The findings lay a scientific foundation for quantitatively evaluating earth buildings’ indoor climate control performance, supporting their integration into green building systems. This research bridges knowledge gaps in micro-to-macro thermal dynamics while advancing the ecological optimization of materials for sustainable architecture. Full article

Graphene oxide (GO) films have attracted significant attention due to their potential in separation and filtration applications. Based on their unique lamellar structure and ultrathin nature, GO films are difficult to maintain in a free-standing form and typically require substrate support. Consequently, understanding their film formation behavior and mechanisms on substrates is of paramount importance. This work employs commonly used nonwoven fibrous membranes as substrates and guided by the coffee-ring theory, systematically investigates the film formation behaviors, film morphology, and underlying mechanisms of GO films on fibrous membranes with varying wettability. Fibrous membranes with different wetting properties—hydrophilic, hydrophobic, and superhydrophobic—were prepared via electrospinning and initiated chemical vapor deposition (iCVD) surface modification techniques. The spreading behaviors, deposition dynamics, capillary effects, and evaporation-induced film formation mechanisms of GO suspensions on these substrates were thoroughly examined. The results showed that GO formed belt-like, ring-like, and circular patterns on the three fibrous membranes, respectively. GO films encapsulated more than the upper half, approximately the upper half, and the top portion of fibers, respectively. Pronounced wrinkling of GO films was observed except for those on the hydrophilic fibrous membrane. This work demonstrates that tuning the wettability of fibrous substrates enables precise control over GO film morphology, including fiber encapsulation, wrinkling, and coverage area. Furthermore, it deepens the understanding of the interactions between 1D nanofibers and 2D GO sheets at low-dimensional scales, laying a foundational basis for the optimized design of membrane engineering. Full article

This study investigates the coupled hygrothermal behavior of mycelium-based composites (MBCs) as a function of their microstructural organization, governed by fungal species, substrate type, additive incorporation, and treatment method. Eleven composite formulations were selected and characterized using a multi-scale experimental approach, combining scanning electron microscopy, dynamic vapor sorption, vapor permeability tests, capillary uptake measurements, and transient thermal conductivity analysis. SEM analysis revealed that Ganoderma lucidum forms dense and interconnected hyphal networks, whereas Trametes versicolor generates looser, localized structures. These morphological differences directly influence water vapor transport and heat conduction. Additive-enriched composites exhibited up to 21.8% higher moisture uptake at 90% RH, while straw-based composites demonstrated higher capillary uptake and free water saturation (up to 704 kg/m³), indicating enhanced moisture sensitivity. In contrast, hemp-based formulations with Ganoderma lucidum showed reduced sorption and vapor permeability due to limited pore interconnectivity. Thermal conductivity varied nonlinearly with temperature and moisture content. Fitting the experimental data with an exponential model revealed a moisture sensitivity coefficient thirty times lower for GHOP compared to VHOP, highlighting the stabilizing effect of a compact microstructure. The distinction between total and effective porosity emerged as a key factor in explaining discrepancies between apparent and functional moisture behavior. These findings demonstrate that hygric and thermal properties in MBCs are governed not by porosity alone, but by the geometry and connectivity of the internal fungal network. Optimizing these structural features enables fine control overheat and mass transfer, laying the groundwork for the development of high-performance, bio-based insulation materials. Full article

It is challenging for mortar to simultaneously enhance the transmission property of water vapor while maintaining excellent waterproofness and impermeability. However, in some applications, both are necessary. Therefore, three different kinds of modifiers, i.e., cementitious capillary crystalline waterproof materials (XYPEX), γ-methacryloxy-propyl-trimethoxy-silane (KH570), and styrene-butadiene rubber latex (SB), are employed to explore how modified mortar can possess excellent waterproofness, impermeability, and the water vapor transmission property simultaneously. Combining characterization techniques, the influencing factors of these three properties are studied. The results indicate that XYPEX promotes the formation of hydration products within pores, improves waterproofness and impermeability, but decreases the water vapor transmission property. KH570 introduces numerous pores ranging from 0.1 to 5 micrometers and enhances the hydrophobicity of mortar; at 1.25% and 2.5% contents, the modified mortar exhibits excellent waterproofness and water vapor transmission property but poor impermeability. SB introduces numerous air pores and forms polymer films; at 20% content, the modified mortar exhibits excellent waterproofness and water vapor transmission property, with impermeability remaining unchanged, making SB a favorable modifier that combines these three properties. Finally, the mechanisms of these three properties are discussed, which provides a theoretical reference for the control of mortar’s waterproofing, impermeability, and water vapor transmission. The selection of modifiers is based on the actual performance requirements. Full article

A series of experiments were conducted on quartz sand beds wetted with transformer oil under initial temperatures of 80–140 °C and fuel–sand mass ratios of 1:4–1:8. The flame spreading process over the fine sand bed wetted with limited liquid fuel can be divided into the development and quasi-steady stages. Experimental results reveal that the flame spread rate in the quasi-steady stage increases with the initial temperature and fuel–sand mass ratio. The effect of sand bed width on flame spread depends on the initial temperature. The flame spread rate is insensitive to the sand bed width at low initial temperatures; however, it increases with sand bed width at an initial temperature close to the flash point of liquid fuel. This discrepancy mainly results from the enhanced capillary effect due to the decreased viscosity at high initial temperatures. The capillary effect is the dominant factor determining fuel vaporization and, thus, the flame spread rate, and flame radiation plays an increasing role with increasing initial temperature. The maximum flame height is sensitive to sand bed width and fuel–sand mass ratio but changes little with initial temperature. A dimensionless model was proposed to predict the normalized flame height. Full article

We present a corrosion-resistant quadrupole ion trap mass spectrometer (QIT-MS) for the direct detection of biosignature gasses in chemically reactive planetary atmospheres, such as Venusian clouds. The system employs a Paul trap with hyperbolic titanium alloy electrodes and alumina spacers for chemical durability and precise ion confinement. An yttria-coated iridium filament serves as the thermionic emitter within a modular electron gun capable of axial and radial ionization. Analytes are introduced through fused silica capillaries and crescent inlets into a miniature pressure cell. The testbed integrates high-voltage RF electronics, pressure-regulated sample delivery, and FPGA-based control for real-time tuning. Continuous operation in 98% sulfuric acid vapor for over three months demonstrated no degradation in emitter or sensor performance. Mass spectra revealed H₂SO₄ fragmentation and thermally induced decomposition up to 425 K. Spectral variations with filament current and electron energy highlight thermal and electron-induced dissociation dynamics. Operational modes include high-resolution scans and selective ion ejection (e.g., CO₂⁺, N₂⁺) to enhance the detection of PH₃⁺, H₂S⁺, and daughter ions. The compact QIT-MS platform is validated for future missions targeting corrosive atmospheres, enabling in situ astrobiological investigations through the detection of biosignature gasses such as phosphine and hydrogen sulfide. Full article

Conventional heat pipes (CHPs) with capillary wicks are fundamental in various engineering applications due to their exceptional heat transfer efficiency and minimal temperature gradients. Despite the recent advancements in heat pipe modeling, existing reviews predominantly emphasize loop or pulsating heat pipes, neglecting the extensive application and design challenges associated with CHPs. This review aims to address this lack by providing a comprehensive analysis of existing modeling techniques for CHPs, with a specific focus on their methodological innovations, validation strategies, and limitations, in order to outline a structured classification of models and provide useful suggestions for future research. The main findings of this work reveal a predominance of numerical lumped parameter models, which balance simplicity and computational efficiency, but often oversimplify complex phenomena. In fact, although numerical 2D and 3D models could offer greater accuracy at higher computational costs, they often share similar limitations with lumped parameter models. Additionally, some crucial aspects, including gravitational effects, real gas behavior in vapor modeling, activation effects, and operating limits, remain underexplored. Therefore, future research should address these gaps, to enhance the applicability of CHPs across different fields and operating conditions. In particular, an integrated approach is recommended, combining physics-based models with data-driven techniques, and supported by a robust and systematic experimental validation strategy, to ensure the reliability and generality of the developed models. Such modeling efforts are expected to guide the development of more effective and reliable heat pipe designs. Full article

By using clear vapor–liquid interface line images of the liquid inside the capillary, the measurement coordinate points of the vapor–liquid interface line were measured. A new method for measuring liquid contact angle has been proposed, which was used to calculate the actual coordinate points and fit the actual vapor–liquid interface line of the liquid. Finally, an angle measurement tool is used to measure the angle of the actual vapor–liquid interface line and obtain the actual contact angle of the liquid. Effectively reducing the influence of refraction on the contact angle by correcting the errors caused by the refractive index of different materials, it can be used for the precise measurement of the static contact angle of liquids. By measuring the static contact angle of the upper and lower liquid surfaces of the liquid column, it was found that the presence of refraction caused a difference of [1.84°, 5.61°] between the actual and measured values of the static contact angle. Full article

Liquid Electron Ionization (LEI) is a powerful and robust interface for the qualitative and quantitative analysis of medium-low-molecular-weight compounds, including numerous environmental pollutants and toxicological substances. Although the robustness and performance of this interface have already been demonstrated, research on its optimization can still improve instrumental performance in terms of detectability. In this study, different setups of the interface’s vaporization micro-channel (VMC) made using different capillaries and various sizes were tested to evaluate the correspondent instrumental performance. The results show that a new combination of capillaries in the interface set up significantly improves instrumental detectability, reaching LOD values almost five times lower than those of the previous setup. Full article

The monitoring of contaminants in imitation jewelry has become important nowadays due to the high amount of products sold worldwide. Due to the complexity of the sample matrix (composed mainly of metals in high concentration), sample analysis can be very challenging. One interesting alternative for this purpose is the use of photochemical vapor generation coupled to inductively coupled plasma optical emission spectrometry (PVG-ICP-OES) due to the ability of separating the analytes from the sample solution prior to analysis; additionally, it is considered an eco-friendly approach if compared to other vapor generation techniques. Thus, this work presents the development and application of a PVG-ICP-OES system for the determination of Hg and Pb in imitation jewelry after sample dissolution in hydrochloric acid. The PVG system was built with two UV lamps (254 nm), a quartz capillary reactor, and a glass gas-liquid separator. Acetic acid concentration and UV exposure time were optimized using a central composite design, as well as the carrier gas flow rate and the radiofrequency (RF) power for the ICP-OES. The optimum conditions were achieved at 30% v/v acetic acid, 60 s reaction time, 0.035 L min⁻¹ carrier gas flow rate, and 1310 W for RF power. The influence of the sample matrix and chemical modifiers were studied, where it was found that the presence of the sample matrix may cause suppression of the analytical signal. The accuracy of the method was evaluated by recovery tests, which ranged from 88 to 102%. The detection limits ranged from 1 to 3 mg g⁻¹, allowing the monitoring of Hg and Pb in imitation jewelry. Full article

Microchannel heat exchangers, with their large specific surface area, exhibit high heat/mass transfer efficiency and have a wide range of applications in chemical engineering and energy. To enhance microchannel flow boiling heat transfer, a top-connected microchannel heat exchanger with a Ni/Ag micro/nano composite surface was designed. Using anhydrous ethanol as the working fluid, comparative flow boiling heat transfer experiments were conducted on regular parallel microchannels (RMC), top-connected microchannels (TCMC), and TCMC with a Ni/Ag micro/nano composite surface (TCMC-Ni/Ag). Results show that the TCMC-Ni/Ag’s maximum local heat transfer coefficient reaches 179.84 kW/m²·K, which is 4.1 times that of RMC. Visualization reveals that its strongly hydrophilic micro/nano composite surface increases bubble nucleation density and nucleation frequency. Under medium-low heat flux, the vapor phase converges in the top-connected region while bubbles form on the microchannel surface; under high heat flux, its capillary liquid absorption triggers a thin-liquid-film convective evaporation mode, which is the key mechanism for improved heat transfer performance. Full article