Search Results (66)

The increasing complexity of urban structures has significantly elevated the risk and severity of façade fires in high-rise buildings. Unlike traditional models assuming continuous fuel beds, real-world fire scenarios often involve discrete combustible materials arranged in discrete fuel matrices. This study presents a systematic investigation into the influence of lateral spacing on vertical flame propagation behavior. Laboratory-scale experiments were conducted using vertically oriented polymethyl methacrylate (PMMA) fuel arrays under nine different spacing configurations. Results reveal that lateral spacing plays a critical role in determining flame spread paths and intensities. Specifically, with a vertical spacing fixed at 8 cm, a lateral spacing of 10 mm resulted in rapid flame growth, reaching a peak flame height of approximately 96.5 cm within 450 s after ignition. In contrast, increasing the lateral spacing to 15 mm significantly slowed flame development, achieving a peak flame height of just under 90 cm at approximately 600 s. This notable transition in flame dynamics is closely associated with the critical thermal boundary layer thickness (~11.5 mm). Additionally, at 10 mm spacing, a chimney-like effect was observed, enhancing upward air entrainment and resulting in intensified combustion. These findings reveal the coupled influence of geometric configuration and heat transfer mechanisms on façade flame propagation. The insights gained provide guidance for cladding system design, suggesting that increasing lateral separation between combustible elements may be an effective strategy to limit flame spread and enhance fire safety performance in buildings. Full article

Metropolitan city express line tunnels are fully enclosed and often span long distances between stations, allowing multiple trains within a single interval. Traditional segmented ventilation ensures only one train per section, but ultra-long tunnels with shaftless designs introduce new challenges under fire conditions. This study investigates smoke behavior in an ultra-long inter-district tunnel during multi-train blockage scenarios. A numerical model evaluates the effects of train spacing, fire source location, and receding spacing on smoke back-layering, temperature distribution, and flow velocity. Results indicate that when train spacing exceeds 200 m and longitudinal wind speed is above 1.2 m/s, the impact of train spacing on smoke back-layering becomes negligible. Larger train spacing increases back-layering under constant wind speed, while higher wind speeds reduce it. Fire source location and evacuation spacing affect the extent and pattern of smoke spread and high-temperature zones, especially under reverse ventilation conditions. These findings provide quantitative insights into fire-induced smoke dynamics in ultra-long tunnels, offering theoretical support for optimizing ventilation control and evacuation strategies in urban express systems. Full article

Wildfires pose increasing risks to human settlements, particularly in the Wildland–Urban Interface (WUI). This study examines the relationship between land cover (LC) characteristics and housing destruction during the 2023 wildfires in Chile’s Bío-Bío region. Using high-resolution remote sensing data and GIS-based multi-buffer spatial analysis (30 m and 100 m), we assessed LC patterns around affected and unaffected rural houses. Results indicate that the proximity of forest plantations significantly increased housing loss, with a notably higher presence of plantations within 30 m of destroyed houses. In contrast, agricultural and pasture mosaics demonstrated a protective function by reducing fire spread. Shrublands also showed moderate protection, albeit with statistical uncertainty. The findings highlight the critical role of immediate LC in determining wildfire impact, emphasizing the need for integrating LC considerations into wildfire risk management, land-use planning, and policy interventions. Strategies such as creating defensible spaces, enforcing zoning regulations, and promoting fire-resistant landscapes can help mitigate future wildfire damage. This research provides spatially explicit insights that contribute to wildfire risk reduction theory and inform targeted prevention and resilience-building strategies in Chile and other fire-prone regions. Full article

The confluence of global warming, the urban heat island effect, and alterations in the nature of underlying surfaces has led to a continuous escalation in the frequency, scale, and intensity of fires within urban green spaces. Mitigating or eliminating the adverse effects of such fires on the service functions of urban ecosystems, while enhancing the resilience of urban greening systems in disaster prevention and risk reduction, has become a pivotal challenge in modern urban development and management. Academic focus has progressively broadened from isolated urban and forest domains to encompass the more intricate environments of the Wildland–Urban Interface (WUI) and urban–suburban forests, with a particular emphasis on the distinctive characteristics of urban greening and in-depth research. This study employs a combination of CiteSpace bibliometric analysis and a narrative literature review to comprehensively examine three critical aspects of urban fire safety as follows: (1) the evaluation of the fire-resistant performance of landscape plants in urban green spaces; (2) the mechanisms of fire behavior in urban greening systems; and (3) the assessment and prediction of urban fire risks. Our findings indicate that landscape plants play a crucial role in controlling the spread of fires in urban green spaces by providing physical barriers and inhibiting combustion processes, thereby mitigating fire propagation. However, the diversity and non-native characteristics of urban greenery species present challenges. The existing research lacks standardized experimental indicators and often focuses on single-dimensional analyses, leading to conclusions that are limited, inconsistent, or even contradictory. Furthermore, most current fire spread models are designed primarily for forests and wildland–urban interface (WUI) regions. Empirical and semi-empirical models dominate this field, yet future advancements will likely involve coupled models that integrate climate and environmental factors. Fire risk assessment and prediction represent a global research hotspot, with machine learning- and deep learning-based approaches increasingly gaining prominence. These advanced methods have demonstrated superior accuracy compared to traditional techniques in predicting urban fire risks. This synthesis aims to elucidate the current state, trends, and deficiencies within the existing research. Future research should explore methods for screening highly resistant landscape plants, with the goal of bolstering the ecological resilience of urban greening systems and providing theoretical underpinnings for the realization of sustainable urban environmental security. Full article

Analyzing wildfire behavior is crucial due to its significant environmental repercussions. Among the various influencing factors, terrain slope and wind velocity are pivotal in governing fire spread characteristics. In the present study, we investigate the influence of negative terrain slopes (up to −45°), backward wind velocities (up to 2 m/s), and their combined effects on the surface fire spread rate using the Wildland-Urban Fire Dynamics Simulator (WFDS). Wind velocity in backward flows reduces the rate of spread by 40% at 30° angles, primarily due to the suppression of radiative heat transfer leading to reduced preheating unburnt areas. However, this effect reduces on lower slopes. The key findings reveal a significant increase in fire intensity and the rate of spread when the terrain slope exceeds 20°. The fire front shape evolves from a relatively flat rounded U-shape to a V-shape; it is shown that a downward slope slightly affects the spread rate, and the fire front shape stays flat. Full article

Wildfires are a recurrent and intensifying natural hazard in Mediterranean regions like Greece, driven by prolonged heatwaves, evolving climatic conditions, and human activities. This study leverages Sentinel-2 satellite imagery and Copernicus geospatial data to assess four early-season wildfire events during May and June 2024, which collectively affected 43.44 km². Burn severity, land cover, and tree cover density were analyzed to evaluate the spatial and environmental impacts of these fires. Validation against Copernicus Emergency Management Service (CEMS) data yielded an overall accuracy of 95.79%, confirming the reliability of the methodology. The Achaia-Ilia wildfire, spanning 40.55 km², exhibited the highest severity, with 26.93% classified as moderate to high severity. Smaller fires, such as Katsimidi (0.66 km²) and Stamata (1.41 km²), revealed the influence of vegetation type and density on fire dynamics, with Stamata’s sparse tree cover mitigating fire spread. The findings highlight the utility of remote sensing technologies for wildfire monitoring, and underscore the need for tailored management strategies, from vegetation control to urban planning, to enhance ecosystem resilience and mitigate wildfire risks in Mediterranean landscapes. Full article

Global climate change is leading to increased wildfire activity in many parts of the world, and with increasing development, a heightened threat to communities in the wildland urban interface. Evaluating the potential for fire to affect communities and critical infrastructure is essential for effective response decision-making and resource prioritization, including evacuation planning, with changing weather conditions during the fire season. Using a receptor–pathway–source assessment framework, we estimate the potential source area from which a wildfire could spread to a community in British Columbia by projecting fire growth outward from the community’s perimeter. The outer perimeter of the source area is effectively an evacuation trigger line for the forecast period. The novel aspects of our method are inverting fire growth in both space and time by reversing the wind direction, the time course of hourly weather, and slope and aspect inputs to a time-evolving fire growth simulation model Prometheus. We also ran a forward simulation from the perimeter of a large fire that was threatening the community to the community edge and back. In addition, we conducted a series of experiments to examine the influence of varying environmental conditions and ignition patterns on the invertibility of fire growth simulations. These cases demonstrate that time-evolving fire growth simulations can be inverted for practical purposes, although caution is needed when interpreting results in areas with extensive non-fuel cover or complex community perimeters. The advantages of this method over conventional simulation from a fire source are that it can be used for pre-attack planning before fire arrival, and following fire arrival, it does not require having an up-to-the-minute map of the fire location. The advantage over the use of minimum travel time methods for inverse modeling is that it allows for changing weather during the forecast period. This procedure provides a practical tool to inform real-time wildfire response decisions around communities, including resource allocation and evacuation planning, that could be implemented with several time-evolving fire growth models. Full article

The frequency of urban fires has grown in recent years everywhere, especially in historic districts, including in Portugal, due to the existence of sensitive igniting materials, the proximity of buildings, the complex urban layout, and the presence of many people. The current study proposes a technique, applied in the Baixa Pombalina (downtown) area in Lisbon, to undertake an appropriate evaluation of the post-earthquake fire cascading effect, which may cause major damage. The earthquake vulnerability and damage scenario were carried out using the Risk-UE method. An empirical fire ignition model was then applied to determine the quantity and location of fire ignitions for different return periods. Furthermore, the simple fire spread Hamada’s model was applied to both the equally spaced grid buildings, as in the original Hamada procedure, and the current study area layout for different time thresholds. Finally, the risk assessment for both models was carried out, allowing for the estimation of earthquake and fire losses, respectively. The results demonstrated that the models are comparable, showing that the Hamada model might be a useful tool for large-scale evaluations aimed at disaster-risk reduction and management since it gives useful information for managing and reducing natural and anthropogenic hazards. Full article

Asymmetrical V-shaped tunnels often appear in tunnels crossing the river or urban underground road tunnels. The smoke flow inside is affected by a lot of factors. A full understanding of the smoke flow in this kind of tunnel is the basis of the smoke control. In this study, the effects of slope composition and fire heat release rate (HRR) on the longitudinal induced airflow velocity, the smoke back-layering length at the small slope side, and the maximum ceiling temperature were studied by the numerical method. The results show that when the fire occurs at the slope change point of the V-shaped tunnel, the maximum ceiling temperature decreases with the increase in the slope of the large-slope side tunnel. The longitudinally induced velocity is primarily related to the slope of the large-slope side tunnel and the fire HRR. When the slope difference between the side tunnels or the slope of the large-slope side tunnel is large, the smoke in the small-slope side tunnel flows back toward the fire source after reaching its maximum dispersion distance and then reaches a quasi-steady state. The smoke back-layering length is mainly affected by the slope and length of the large-slope side tunnel. When the slope of the large-slope side tunnel is 9%, the induced airflow velocity from the small-slope side can prevent the spread of smoke. The empirical models of the smoke back-layering length and the longitudinal induced airflow velocity in the small-slope side tunnel are drawn, respectively, by the theoretical analysis and the numerical results. This study can provide technical support for the design and operation of smoke control systems in V-shaped tunnels. Full article

Fire is a prevalent hazard that poses a significant risk to public safety and societal progress. The continuous expansion of densely populated urban areas, exacerbated by global warming and the increasing intensification of urban heat islands, has led to a notable increase in the frequency and severity of fires worldwide. Incorporating measures to withstand different types of calamities has always been a crucial aspect of urban infrastructure. Well-designed plant communities play a pivotal role as a component of green space systems in addressing climate-related challenges, effectively mitigating the occurrence and spread of fires. This study conducted field research on 21 sites in the green belt around Shanghai, China, quantifying tree morphological indexes and coordinate positions. The spatial structure attributes of different plant communities were analyzed by principal component analysis, CRITIC weighting approach, and stepwise regression analysis to build a comprehensive fire resistance prediction model. Through this research, the relationship between community spatial structures and fire resistance was explored. A systematic construction of a prediction model based on community spatial structures for fire resistance was undertaken, and the fire resistance performance could be quickly judged by easily measured tree morphological indexes, providing valuable insights for the dynamic prediction of fire resistance. According to the evaluation and ranking conducted by the prediction model, the Celtis sinensis, Sapindus saponaria, Osmanthus fragrans, Koelreuteria paniculata, and Distylium racemosum + Populus euramericana ‘I-214’ communities exhibited a high level of fire resistance. On the other hand, the Koelreuteria bipinnata + Ligustrum lucidum, Ginkgo biloba + Camphora officinarum + Ligustrum lucidum, and Ligustrum lucidum + Sapindus saponaria communities obtained lower scores and were positioned lower in the ranking. It is emphasized that the integration of monitoring and regulation is essential to ensure the ecological integrity and well-being of green areas in the Wildland–Urban Interface. Full article

Proactive prevention and fighting fire at industrial facilities, often located in urbanized clusters, should include the use of modern methods for modeling danger zones that appear during the spread of the harmful combustion products of various chemicals. Simulation modeling is a method that allows predicting the parameters of a danger zone, taking into account a number of technological, landscape, and natural-climatic factors that have a certain variability. The purpose of this research is to develop a mathematical simulation model of the formation process of a danger zone during an emergency at an industrial facility, including an explosion of a container with chemicals and fire, with the spread of an aerosol and smoke cloud near residential areas. The subject of this study was the development of a simulation model of a danger zone of combustion gases and its graphical interpretation as a starting point for timely decision making on evacuation by an official. The mathematical model of the process of danger zone formation during an explosion and fire at an industrial facility presented in this article is based on the creation of a GSL library from data on the mass of explosion and combustion products, verification using the Wald test, and the use of algorithms for calculating the starting and ending points of the danger zone for various factor values’ variables, constructing ellipses of the boundaries of the distribution of pollution spots. The developed model makes it possible to calculate the linear dimensions and area of the danger zone under optimistic and pessimistic scenarios, constructing a graphical diagram of the zones of toxic doses from the source of explosion and combustion. The results obtained from the modeling can serve as the basis for making quick decisions about evacuating residents from nearby areas. Full article

In 2020, wildfires scarred over 4,000,000 hectares in the western United States, devastating urban populations and ecosystems alike. The significant impact that wildfires have on plants, animals, and human environments makes wildfire adaptation, management, and mitigation strategies a critical task. This study uses satellite imagery from Landsat to calculate burn severity and map the fire progression for the Dolan Fire of central Coastal California which occurred in August 2020. Several environmental factors, such as temperature, humidity, fuel type, topography, surface conditions, and wind velocity, are known to affect wildfire spread and burn severity. The aim of this study is the investigation of the relationship between these environmental factors, estimates of burn severity, and fire spread patterns. Burn severity is calculated and classified using the Difference in Normalized Burn Ratio (dNBR) before being displayed as a time series of maps. The Dolan Fire had a moderate severity burn with an average dNBR of 0.292. The ignition site location, when paired with the patterns of fire spread, is consistent with wind speed and direction data, suggesting fire movement to the southeast of the fire ignition site. Patterns of increased burn severity are compared with both topography (slope and aspect) and fuel type. Locations that were found to be more susceptible to high burn severity featured Long Needle Timber Litter and Mature Timber fuels, intermediate slope angles between 15 and 35°, and north- and east-facing slopes. This study has implications for the future predictive modeling of wildfires that may serve to develop wildfire mitigation strategies, manage climate change impacts, and protect human lives. Full article

As an integral part of the 2030 Agenda for Sustainable Development, Disaster Risk Reduction (DRR) is essential for human safety and city sustainability. In recent years, natural disasters, which have had a tremendous negative impact on economic and social development, have frequently occurred in cities. As one of these devastating disasters, earthquakes can severely damage the achievements of urban development and impact the sustainable development of cities. To prepare for potential large earthquakes in the future, efficient evacuation plans need to be developed to enhance evacuation efficiency and minimize casualties. Most previous research focuses on minimization of distance or cost while ignoring risk factors. We propose a multi-objective optimization model with the goal of reducing the risk during the evacuation process, which is called the risk reduction model (RRM). Problem-specific indicators for screening optimal solutions are introduced. The research selects the Ogu area in Tokyo as a case study, where there is a relatively high density of wooden structures, increasing the risks of building collapse and fire spread after an earthquake, and is based on a two-phase evacuation flow that considers secondary evacuation for fire response. The results indicate that, in this case, RRM can, in most situations, reduce the risk level during the evacuation process and improve evacuation efficiency and success rate without significantly increasing the total evacuation distance. It proves to be superior to the traditional distance minimization model (DMM), which prioritizes minimizing the total distance as the objective function. Full article

The urban utility tunnel is an indispensable part of modern engineering construction. However, the fire risk cannot be ignored due to the narrow space and limited ventilation of the utility tunnel. A study of smoke filling is performed in a 1/8-scaled utility tunnel (25 m × 0.5 m × 0.45 m). Five heat release rates (5, 10, 15, 20 and 25 kW) and four positions of fire sources are used for tests. The initial position of the one-dimensional smoke movement of strong plume is determined. Based on the traditional model, the longitudinal temperature attenuation model of tunnel smoke is established with consideration of radiation and convection heat losses. The theoretical value of the longitudinal temperature rise of smoke is in good agreement with the experimental value. A one-dimensional spreading velocity model is established that coincides well with the experimental value, and the relative error is less than 20%. The spreading velocity of smoke is increased by the heat release rate. The velocity of the smoke spreading at the near end is smaller than that at the center, due to the long spreading route. The current conclusions disclosed in this study provide important guidance for the ventilation design of utility tunnels for fire smoke scenarios. Full article

Fires resulting from antecedent fires, known as exposure fires, can manifest across diverse environments, including suburban, urban, and rural areas. Notably, exposure fires represented by structure-destroying fires within the wildland–urban interface (WUI) can extend into non-WUI suburban and urban regions, presenting significant challenges. Leveraging data from the United States National Fire Incident Reporting System (NFIRS) spanning 2002 to 2020, this study investigates 131,739 exposure fire incidents impacting 348,089 features (incidents). We analyze reported economic costs, affected feature types, and property utilization patterns for these exposure fires. We also compare these exposure fires to information documented in other databases. Finally, we examine structure separation distance at residential dwellings and describe ignition pathways for selected fires. Reported property losses for some fire incidents amounted to USD 5,647,121,172, with content losses totaling USD 1,777,345,793. Prominent fire incident categories include buildings, vehicles, and natural vegetation fires, predominantly occurring in residential, outdoor, and storage areas. While the NFIRS lacked information on most major structure-destroying WUI fires, highlighting this analysis’s lack of statistical representation, it did provide insights into less extensive exposure fires, both WUI and non-WUI, unrecorded elsewhere. Our study reveals significant distinctions in the distribution of separation distances between damaged-to-damaged structures (average separation of 6.5 m) and damaged-to-not-damaged structures (average separation of 18.1 m). Notably, 84% of the incidents in exposure fires involved fire suppression defensive actions. These defensive actions contributed to the differences in structure separation distance distributions, highlighting the often-neglected role of these measures in assessing structure responses during WUI fires. We examined ignition pathways at select exposure fires, highlighting some common features involved in fire spread and challenges in documenting these pathways. Finally, we propose a set of idealized attributes for documenting exposure fires, accentuating the inherent difficulties in collecting such data across expansive geographical areas, particularly when striving for statistical representation. Our findings yield valuable insights into the multifaceted nature of exposure fires, informing future research and database development to aid in mitigating their impact on vulnerable communities. Full article