Search Results (310)

2,4-Dichlorophenoxyacetic acid (2,4-D) is an extensively applied organic compound, primarily for agricultural weed control and plant growth agents. Although 2,4-D usually exists in the environment in low volumes, the detection of 2,4-D is critical for human health and environmental safety. In this work, a biophotonic biosensor was fabricated by coating the surface of a tapered optical fiber with gold nanoparticles (AuNPs) to excite the localized surface plasmon resonance (LSPR) and functionalizing the fiber with molybdenum disulfide nanosheets (MoS₂-NSs)/zinc oxide nanowires (ZnO-NWs) to extend the effective sensing area. Due to the inhibitory effect of 2,4-D on the hydrolytic activity of ALP, the refractive index (RI) around the sensor surface changes, leading to a shift in the LSPR peak wavelength. According to this sensing technique, the sensor can detect concentrations in the range of 1–10 mg/L, with a limit of detection (LOD) of 0.29 mg/L. The stability, repeatability and selectivity tests show that the sensor has good stability and selectivity. In the actual sample detection experiment, the recovery rates of apples and Chinese cabbage were 96.2–100.4% and 83.8–108.8%, respectively, which indicated that the detection method had good accuracy for the detection of target substances in actual samples. Thus, the proposed sensor has an important application in the detection of 2,4-D herbicides. Full article

This paper proposes and experimentally demonstrates a fiber ring laser (FRL) salinity sensing system based on a Sagnac loop (SL) formed by a tapered polarization-maintaining fiber (TPMF). The operating principle is that salinity modulates the birefringence of the polarization-maintaining fiber (PMF), causing a shift in the interference wavelength of the SL transmission spectrum, while the FRL narrows the optical spectrum and enhances the signal-to-noise ratio (SNR). In the experiment, the SL consists of a 20-cm-long PMF with a tapered waist diameter of 10.86 μm. Over the salinity range of 0‰ to 30‰, the sensitivity of the laser-based sensing system is 97 pm/‰, which agrees well with the 93 pm/‰ sensitivity obtained using a broadband light source (BBS), and the salinity exhibits a good linear relationship with the wavelength shift, with a coefficient of determination (R²) of 0.997. Meanwhile, the ring laser cavity improves the SNR of the sensing system from 22 dB to approximately 54 dB, and compresses the 3-dB bandwidth from 1.75 nm to 0.06 nm. Further adopting the support vector regression (SVR) algorithm for linear regression modeling of the spectral data, the results show that the mean absolute error (MAE) decreases from 0.50‰ to 0.04‰, the root mean square error (RMSE) decreases from 0.54‰ to 0.11‰, and R² reaches as high as 0.99988. To the best of our knowledge, this is the first work that combines salinity laser sensing with an artificial intelligence algorithm. The proposed sensor leverages the narrow linewidth and high SNR advantages of the FRL together with the high-precision linear fitting capability of the SVR algorithm, achieving significantly improved accuracy for salinity measurement compared to conventional spectral demodulation. Full article

This paper presents a high-sensitivity and anti-interference optical intensity differential curvature sensor based on seven-core fiber (SCF), and its performance is verified through simulation. The sensor adopts a “single-mode fiber–tapered SCF” structure, using the light intensity ratio between the peripheral core and the central core for curvature demodulation. It enhances the sensitivity while effectively suppressing common-mode interference. The simulation results show that when the cone zone diameter of the tapered SCF is optimized to 30 µm, the mode coupling between the cores is significant, forming a strongly coupled super-mode transmission system. Based on the intensity differential principle, this sensor achieves excellent linear response within the curvature range of 0–10 m⁻¹, with a sensitivity of −0.145/m⁻¹. The sensor has a compact structure and simple fabrication process, providing new ideas and solutions to break through the technical bottlenecks of existing fiber curvature sensors, and has broad application prospects in engineering monitoring fields. Full article

In this work, we propose a bamboo-shaped Mach-Zehnder interferometer coated with chitosan for relative humidity (RH) and temperature measurement. The sensor is fabricated by fusing no-core fiber and multimode fiber segments through arc discharge, followed by tapering with a hydrogen–oxygen flame to form a unique bamboo-shaped configuration. To functionalize the structure for humidity sensing, chitosan is coated onto the fiber surface. The refractive index of chitosan varies with water molecule adsorption, which enhances the spectral response of the sensor to RH. Therefore, the sensitivity response is enhanced after the film coating is applied. Experimental results demonstrate that the proposed sensor achieves the maximum sensitivities to RH and temperature determined at −0.9261 nm/%RH and 0.0952 nm/°C, respectively. The sensor features a compact structure, high sensitivity and the ability to achieve dual-parameter sensing, which supports applications in biomedical, agricultural and electronic manufacturing fields. Full article

Rare-earth-doped microsphere cavities have attracted significant interest for applications in miniaturized photonic devices due to their unique optical properties. In this work, Yb³⁺/Er³⁺ co-doped microsphere cavities were fabricated via a melting method, which enables uniform interior doping at high and tunable rare-earth concentrations through a simpler and more cost-effective process compared with existing coating and fiber-etching approaches. Whispering gallery modes (WGMs) enhanced upconversion luminescence, which was observed using tapered fiber coupling, producing a vivid green fluorescence ring near the equatorial region of the microsphere. The luminescence characteristics of the microsphere cavity were investigated by measuring the fluorescence spectra under varying excitation powers. The results indicated that the fluorescence emission follows a two-photon absorption process, consistent with the upconversion emission mechanism of Er³⁺. A finite difference time domain (FDTD) model was employed to simulate the optical field distribution within the microsphere cavity. At a microsphere diameter of 90 μm and a coupling gap of 0 μm, both the 980 nm pump light and the emitted light were effectively confined near the equatorial region of the microsphere, forming WGM confinement patterns. These findings are expected to advance the application of rare-earth-doped microsphere cavities in fields such as biosensing, bioimaging, optical communications, and upconversion microlasers. Full article

Additive manufacturing by Fused Filament Fabrication (FFF) enables the fabrication of complex polymer components, although limitations in surface quality and dimensional accuracy often require post-processing. Abrasive water jet machining (AWJM) is a non-thermal technique suitable for improving surface integrity in polymers and composites without inducing thermal damage. This study investigates the AWJM performance on FFF-printed polylactic acid (PLA) and carbon-fiber-reinforced PLA (PLA–CF), focusing on the influence of water pressure (WP), traverse feed rate (TFR), and abrasive mass flow rate (AMFR). A full factorial design was implemented, and surface integrity was evaluated through surface roughness (Ra) and kerf taper (T), considering their variation across characteristic cutting regions: initial damage region (IDR), smooth cutting region (SCR), and rough cutting region (RCR). Results show that WP and TFR are the dominant parameters, while AMFR has a limited effect within the studied range. The SCR exhibits the lowest roughness, whereas the RCR shows significant degradation due to energy loss. Both materials present similar behavior, with only minor improvements in PLA–CF. ANOVA confirms that process parameters have a stronger influence than material type, providing useful criteria for AWJM optimization in FFF polymers. Full article

We extended self-similar amplification to a large-mode-area tapered Yb-doped fiber (LMA T-YDF) with longitudinally decreasing nonlinearity. The theoretical analysis and numerical simulation demonstrate that T-YDFs with different nonlinearity profiles can achieve self-similar evolution, which is confirmed by a self-similar amplifier that employs two kinds of T-YDFs. Further experimental study indicates that the T-YDF with a large core diameter at the thin end can achieve self-similar evolution across a wide range of pump powers and generate 51 W average power, 34 fs nearly transform-limited (TL) pulses with 32 dB gain. To the best of our knowledge, this is the first theoretical and experimental demonstration of self-similar amplification in T-YDFs. The high-gain feature of the T-YDF simplifies the laser system and can be used to build a compact all-fiber high-power femtosecond laser source. Full article

To address the need for high electrical insulation, strong immunity to electromagnetic interference, and miniaturized AC electrical-signal detection in complex electromagnetic environments, we propose and experimentally demonstrate a fiber-optic sensor based on a piezoelectric ceramic (PZT)-driven ring tapered-fiber resonator. The applied AC excitation is converted into periodic mechanical deformation through the inverse piezoelectric effect of the PZT, and the resulting strain modulates the resonator response, enabling optical demodulation of the input frequency and amplitude. A comprehensive figure of merit was introduced to optimize the tapered-fiber geometry, yielding an optimal waist diameter of approximately 10 μm. The sensor can effectively distinguish both single- and dual-frequency AC signals. Over the range of 50–500 Hz, the demodulated frequency agrees closely with the input frequency, with a linear fitting coefficient of 0.9999. At a fixed driving frequency of 250 Hz, the amplitude of the characteristic spectral peak increases nearly linearly with the input voltage amplitude, with a fitting coefficient of 0.9945. The device also exhibits good stability over 30–150 °C and during 70 h of continuous operation. With its simple structure, low cost, and strong immunity to electromagnetic interference, this sensor provides a practical solution for AC electrical-signal detection in complex environments. Full article

Exhaled breath analysis offers a non-invasive route for metabolic monitoring and disease screening, but its practical implementation requires sensing platforms that combine high sensitivity, robustness, and simplicity. Here, we report an evanescent wave-excited fiber-optic surface-enhanced Raman scattering (SERS) sensor based on silver nanocubes (Ag NCs) assembled onto a fiber taper waist (FTW), and the design is further extended to an Ag/graphene oxide (GO) hybrid interface for enhanced gas detection. Finite element and finite-difference time-domain simulations were employed to optimize the FTW geometry and Ag NC dimensions for efficient evanescent-field excitation and plasmonic enhancement. The fabricated FTW-SERS probe achieved a minimum detectable concentration of 10⁻⁹ M for crystal violet, together with good linearity and a relative standard deviation below 5%. For gas sensing, ethanol and acetone vapors were detected down to 50 ppm using the Ag NC-based FTW-SERS probe. After introducing a 0.3 mg/mL GO functional layer, the minimum detectable concentrations of both analytes were further reduced to 25 ppm. In addition, proof-of-concept monitoring of exhaled ethanol after alcohol consumption revealed dynamic spectral changes consistent with ethanol metabolism. These results demonstrate the potential of evanescent wave-excited FTW-SERS probes for compact and sensitive breath-analysis applications. Full article

In extreme scenarios such as nuclear explosions and high-energy radiation detection in space, UV-cured adhesives are usually used as coupling media to bind tapered optic fiber arrays with intensified charge-coupled devices or complementary metal–oxide semiconductors and a tapered optic fiber array for effective optical signal transmission. To address the issue of weak bonding strength caused by the small binding area between charge-coupled devices or complementary metal–oxide semiconductors and TOFA, a stage-wise curing process was investigated and proved to be efficient through comparison with the single curing process. The effect of interval time between the initial and final curing on coupling strength was characterized by tensile strength, shear strength and shock acceleration testing, and the samples were exposed to high and low temperatures for evaluation of their environmental adaptability. The curing mechanism was analyzed by surface morphology of the adhesive layer after decoupling and an energy-dispersive X-ray spectroscopy elemental analysis of interface layer. The results show that when the interval time is extended from 5 min to 60 min, the shock acceleration of the coupling device decreases by 26.1%, while the tensile and shear strengths also decrease by 49.4% and 60.7%, respectively. The decline in coupling strength is attributed to oxygen inhibition during interval time. The exposure of the adhesive surface to the air allows oxygen to diffuse into and react with active the free radicals that remain from the initial curing, which inhibits further polymerization and generates a thin, incompletely cured weak boundary layer. These findings provide insights for optimizing stage-wise curing processes and improving the reliability of coupled imaging devices. Full article

Polymer nanocomposites offer significant potential for improving the strength-to-weight ratio and dynamic behavior of drone blades. This study examines the vibration characteristics of tapered aramid (Kevlar)/epoxy composite blades reinforced with nanocarbon fillers—graphene (2D), multi-walled carbon nanotubes (MWCNTs, 1D), and fullerene (0D)—to determine the most effective filler for enhancing stiffness and operational stability. The laminated blades (300 mm length, 200 mm width, root thickness 13 mm, tip thickness 8 mm) incorporate ply drop-offs and a central honeycomb core. Modeling was performed using classical laminate plate theory integrated with the finite element method (FEM) in MATLAB (R2016a). Under clamped–free–free–free boundary conditions, the study considered rotational speeds of 750–2250 rpm, setting angles of 30–60°, various fiber orientations, and nanofiller contents of 0–10 wt.%. The results indicate that while the setting angle minimally affects natural frequency, it significantly influences damping in modes (1,2) and (2,1). Increasing nanofiller content improves stiffness, with optimal performance observed near 5 wt.%. At 1500 rpm in mode (1,1), MWCNTs provided the greatest enhancement. Overall, MWCNTs exhibited superior stiffness improvement and rotational stability compared to other fillers. Full article

This study addresses the problem of whispering gallery mode (WGM) selection in spherical microresonators by means of their femtosecond micro-processing. The proposed method involves fabrication on the microsphere surface of defects playing the role of scattering elements for higher-order modes with low azimuthal mode indices. These two T-shaped trenches are created using femtosecond laser ablation, with a depth of 2 microns, gap of 30 microns between them, and each of length of 20 microns along the equatorial direction. A tapered fiber with a sub-micron waist diameter serves as the excitation element for WGMs. This method allows for spectral purification of the WGMs, reducing the number of resonances by 180 times, with a quality factor of $Q>{10}^5$ for the non-inverted spectrum in the form of resonance dips. Additionally, an inverted spectrum with narrow resonance peaks of about 35%, low background level and single mode regime with 3 dB side peak suppression has been simultaneously achieved in the taper transmission, for the first time to our knowledge. The latter was obtained by exciting the microsphere at the taper waist. These results hold promise for the development of narrowband filters, laser mode selectors, and optical sensors based on microresonators. Full article

This paper presents a novel carbon fiber reinforced polymer (CFRP) crash box design, incorporating numerical analysis and manufacturing aspects. Within the design and analysis phases, a novel numerical methodology is employed to mitigate computational costs in estimating specific energy absorption (SEA). The proposed approach involves a reduction in ply interfaces and modification of pertinent material properties to optimize energy dissipation, achieving more than 50% reduction in simulation time. This methodology is applied to the design of a composite crash box made of unidirectional (UD) carbon/epoxy prepregs, resulting in a new geometry: sun-like shape featuring four sinusoidal arms connected to a central circular core. Subsequent manufacturing and testing reveal a SEA value of 79.46 J/g for designed geometry, surpassing metallic counterparts by a factor of 3 to 4. Furthermore, this study conducts a comparative analysis of energy absorption performance between unidirectional and woven fabric prepregs for the same geometry. Utilizing carbon/epoxy woven fabric (WF) prepregs further enhances the SEA to 89.26 J/g. Finally, the application of edge tapering to the crash box structure is shown to eliminate initial peak loads, thereby preventing excessive deceleration. Full article

Optical fiber surface plasmon resonance (SPR) sensing, as a label-free, highly sensitive, rapid-response and in situ detection technology, has demonstrated significant utility in various physical, chemical and biological detection applications. This paper focuses on a fiber-integrated microscale spiral-grating tapered gold tip SPR sensor. We first introduce the working principle and sensing capability with high space–time resolution of this SPR microsensor. Then we provide a comprehensive description of its application in the study on the important fundamental scientific issue of liquid–liquid diffusion. Finally, we demonstrate the application of the spiral-grating tapered gold tip to plasmonic enhanced fluorescence and scanning near-field optical microscopy. By systematically summarizing the excellent multifunctional sensing performance of the microscale spiral-grating tapered gold tip, this paper aims to provide new optical schemes and tools for the study on complex physicochemical processes and light-matter interactions at microscale and nanoscale. Full article

We propose a vector bending sensor based on a tapered few-mode multi-core fiber (FM-MCF). A seven-core six-mode fiber is tapered with an optimized taper ratio, enabling bending sensing through power monitoring. When the tapered FM-MCF bends, coupling occurs between the central core and side cores in the tapered region. By monitoring the power of all cores and employing a power differential method, the bending direction and curvature can be reconstructed. The results show that within a curvature range of 2.5 m⁻¹ to 10 m⁻¹, the sensitivity of the ratio of the side core’s power to the middle core’s power with respect to curvature is not less than 0.14/m⁻¹. A deep fully connected feedforward neural network (DNN) is used to demodulate all power information and predict the bending shape of the optical fiber. The algorithm predicts the bending radius and rotation angle with mean absolute errors less than 0.038 m and 3.087°, respectively. This method is expected to achieve low-cost, high-sensitivity bending measurement applications with vector direction perception, providing an effective solution for scenarios with small curvatures that are challenging to detect using conventional sensing methods. Full article