Search Results (19)

(1) Background: Generation IV supercritical water-cooled reactors (SCWRs), including small modular reactor (SCW-SMR) variants, are pivotal in nuclear technology. Operating at 300–500 °C and 25 MPa, these reactors require detailed understanding of radiation chemistry and transient species to optimize water chemistry, reduce corrosion, and enhance safety. Boron, widely used as a neutron absorber, plays a significant role in reactor performance and safety. This study focuses on the yields of radiolytic species in subcritical and supercritical water exposed to ⁴He and ⁷Li recoil ions from the ¹⁰B(n,α)⁷Li fission reaction in SCWR/SCW-SMR environments. (2) Methods: We use Monte Carlo track chemistry simulations to calculate yields (G values) of primary radicals (e⁻_aq, H^•, and ^•OH) and molecular species (H₂ and H₂O₂) from water radiolysis by α-particles and Li³⁺ recoils across 1 picosecond to 0.1 millisecond timescales. (3) Results: Simulations show substantially lower radical yields, notably e⁻_aq and ^•OH, alongside higher molecular product yields compared to low linear energy transfer (LET) radiation, underscoring the high-LET nature of ¹⁰B(n,α)⁷Li recoil nuclei. Key changes include elevated G(^•OH) and G(H₂), and a decrease in G(H^•), primarily driven during the homogeneous chemical stage of radiolysis by the reaction H^• + H₂O → ^•OH + H₂. This reaction significantly contributes to H₂ production, potentially reducing the need for added hydrogen in coolant water to mitigate oxidizing species. In supercritical conditions, low G(H₂O₂) suggests that H₂O₂ is unlikely to be a major contributor to material oxidation. (4) Conclusions: The ¹⁰B(n,α)⁷Li reaction’s yield estimates could significantly impact coolant chemistry strategies in SCWRs and SCW-SMRs. Understanding radiolytic behavior in these conditions aids in refining reactor models and coolant chemistry to minimize corrosion and radiolytic damage. Future experiments are needed to validate these predictions. Full article

(1) Background: Supercritical water-cooled reactors (SCWRs) and their smaller modular variants (SMRs) are part of the ‘Generation IV International Forum’ (GIF) on advanced nuclear energy systems. These reactors operate beyond the critical point of water (t_c = 373.95 °C and P_c = 22.06 MPa), which introduces specific technical challenges that need to be addressed. The primary concerns involve the effects of intense radiation fields—including fast neutrons, recoil protons/oxygen ions, and γ rays—on the chemistry of the coolant fluid and the integrity of construction materials. (2) Methods: This study employs Monte Carlo simulations of radiation track chemistry to investigate the yields of radiolytic species in SCWRs/SMRs exposed to 2 MeV neutrons. In our calculations, only the contributions from the first three recoil protons with initial energies of 1.264, 0.465, and 0.171 MeV were considered. Our analysis was conducted at both subcritical (300 and 350 °C) and supercritical temperatures (400–600 °C), maintaining a constant pressure of 25 MPa. (3) Results: Our simulations provide insights into the radiolytic formation of chemical species such as e⁻_aq, H^●, H₂, ^●OH, and H₂O₂ from ~1 ps to 1 ms. Compared to data from radiation with low linear energy transfer (LET), the G(e⁻_aq) and G(^●OH) values obtained for fast neutrons show a similar temporal dependence but with smaller amplitude—a result demonstrating the high LET nature of fast neutrons. A notable outcome of our simulations is the marked increase in G(^●OH) and G(H₂), coupled with a corresponding reduction in G(H^●), observed during the homogeneous chemical stage of radiolysis. This evolution is attributed to the oxidation of water by the H^● atom according to the reaction H^● + H₂O → ^●OH + H₂. This reaction acts as a significant source of H₂, potentially reducing the need to add extra hydrogen to the reactor’s coolant water to suppress the net radiolytic production of oxidizing species. Unlike in subcritical water, our simulations also indicate that G(H₂O₂) remains very low in low-density SCW throughout the interval from ~1 ps to 1 ms, suggesting that H₂O₂ is less likely to contribute to oxidative stress under these conditions. (4) Conclusions: The results of this study could significantly impact water-chemistry management in the proposed SCWRs and SCW-SMRs, which is crucial for assessing and mitigating the corrosion risks to reactor materials, especially for long-term operation. Full article

Tetra pak packaging is one of the most frequently used types of packaging in the food industry. The recycling of the tetra pak packaging waste presents a difficult task because of its multi-layered, multi-component structure. In this study, the degradation of tetra pak packaging in subcritical (SubCW) and supercritical (SCW) water was investigated. The experiments were carried out in one (SCW) or two stages (SubCW and SCW), whereby the influence of the reaction temperature and time on the yield and composition of the products obtained was investigated. The maximum oil phase yield achieved in a one-stage and a two-stage degradation process was 60.7% and 65.5%, respectively. The oil and gas phases were composed of different types of hydrocarbons. Higher temperature and longer time led to higher amounts of saturated aliphatic hydrocarbons in both the oil and gas phases. The aqueous phase contained sugars (glucose, fructose) and sugar derivatives (levulinic acid, glyceraldehyde, furfurals). Based on these results, the degradation pathway of waste tetra pak packaging in SubCW and SCW was proposed. The results of the study show that the degradation of waste tetra pak packaging with SubCW and SCW is a promising recycling process. Full article

(1) Background: In the quest to accurately model the radiolysis of water in its supercritical state, a detailed understanding of water’s molecular structure, particularly how water molecules are arranged in this unique state, is essential. (2) Methods: We conducted molecular dynamics simulations using the SPC/E water model to investigate the molecular structures of supercritical water (SCW) over a wide temperature range, extending up to 800 °C. (3) Results: Our results show that at a constant pressure of 25 MPa, the average intermolecular distance around a reference water molecule remains remarkably stable at ~2.9 Å. This uniformity persists across a substantial temperature range, demonstrating the unique heterogeneous nature of SCW under these extreme conditions. Notably, the simulations also reveal intricate patterns within SCW, indicating the simultaneous presence of regions with high and low density. As temperatures increase, we observe a rise in the formation of molecular clusters, which are accompanied by a reduction in their average size. (4) Conclusions: These findings highlight the necessity of incorporating the molecular complexity of SCW into traditional track-structure chemistry models to improve predictions of SCW behavior under ionizing radiation. The study establishes a foundational reference for further exploration of the properties of supercritical water, particularly for its application in advanced nuclear technologies, including the next generation of water-cooled reactors and their small modular reactor variants that utilize SCW as a coolant. Full article

Supercritical water gasification (SCWG) technology is highly promising for its ability to cleanly and efficiently convert biomass to hydrogen. This paper developed a model for the gasification of rice straw in supercritical water (SCW) to predict the direction and limit of the reaction based on the Gibbs free energy minimization principle. The equilibrium distribution of rice straw gasification products was analyzed under a wide range of parameters including temperatures of 400–1200 °C, pressures of 20–50 MPa, and rice straw concentrations of 5–40 wt%. Coke may not be produced due to the excellent properties of supercritical water under thermodynamic constraints. Higher temperatures, lower pressures, and biomass concentrations facilitated the movement of the chemical equilibrium towards hydrogen production. The hydrogen yield was 47.17 mol/kg at a temperature of 650 °C, a pressure of 25 MPa, and a rice straw concentration of 5 wt%. Meanwhile, there is an absorptive process in the rice straw SCWG process for high-calorific value hydrogen production. Energy self-sufficiency of the SCWG process can be maintained by adding small amounts of oxygen (ER < 0.2). This work would be of great value in guiding rice straw SCWG experiments. Full article

Inorganic components in coal play a significant role during the supercritical water gasification (SCWG) process. This study comprehensively investigated the effect of major mineral components (SiO₂, Al₂O₃, and CaO) on the SCWG of semi-coke with/without K₂CO₃. The inhibition/promotion mechanism and conversion of mineral chemical components were explored. The results showed that, without K₂CO₃, CaO promoted gasification because CaO’s adsorption of CO₂ contributed to the fixed carbon steam reforming reaction and the catalysis of highly dispersed calcite. When K₂CO₃ was added, SiO₂ and CaO were prone to sintering and agglomeration due to the formation of low-melting-point minerals, which hindered further gasification of fine carbon particles. Al₂O₃ prevented the aggregation of slags, increased the probability of fine carbon particles contacting SCW and K₂CO₃, and promoted complete gasification. This study’s results may provide theoretical guidance for the directional control of minerals in coal during SCWG, and complete gasification of solid-phase carbon can be achieved by properly adjusting the mineral components. Full article

Utilizing Monte Carlo multi-track chemistry simulations along with a cylindrical instantaneous pulse (Dirac) irradiation model, we assessed the initial acidic response in both subcritical and supercritical water under high radiation dose rates. This investigation spans a temperature range of 300 to 500 °C at a nominal pressure of 25 MPa, aligning with the operational conditions anticipated in proposed supercritical water (SCW)-cooled small modular reactors (SCW-SMRs). A pivotal finding from our study is the observation of a significant ‘acid spike’ effect, which shows a notable intensification in response to increasing radiation dose rates. Our results bring to light the potential risks posed by this acidity, which could potentially foster a corrosive environment and thereby increase the risk of accelerated material degradation in reactor components. Full article

Pharmaceutical pollutants are considered emerging contaminants, representing a significant concern to the ecosystem. Thus, this study reports on the degradation of antihypertensive and cardiovascular drugs (atenolol, captopril, propranolol hydrochloride, diosmin, hesperidin, losartan potassium, hydrochlorothiazide, and trimetazidine) present in simulated wastewater through applying the technology of oxidation using supercritical water (SCW). The operational parameters of the treatment process, particularly the feed flow rate, temperature, and concentration of H₂O₂, were assessed. A central composite design of experiments associated with differential evolution was employed in the optimization. Both liquid and gaseous phase products were submitted to physical–chemical characterization. As a result, the optimized conditions for the treatment were discovered to be a feed flow rate of 13.3 mL/min, a temperature of 600 °C, and a H₂O₂ oxidation coefficient of 0.65, corresponding to the oxygen stoichiometric coefficient in the carbon oxidation chemical reaction. Under optimal conditions, the total organic carbon (TOC) decreased from 332 to 25 mg/L (92.1%), and the pharmaceutical molecules underwent near-complete degradation. The physical–chemical parameters also met with the main environmental regulations for wastewater disposal. The compounds determined in the gaseous phase were CO₂ (97.9%), H₂ (1.3%), CH₄ (0.3%), and CO (0.5%.). Additionally, a modeling thermodynamic equilibrium of the system was performed, based on the experimental data. The results revealed that SCW technology has a great potential to oxidize/degrade organic matter and can be applied to treat pharmaceutical pollutants. Full article

One of the challenges of small modular reactors (SMRs) in comparison with large reactors is the greater difficulty in achieving high burnups in smaller cores. With greater neutron leakage through the periphery, a key factor is the neutron economy of the fuel cladding. However, all large supercritical water-cooled reactor (SCWR) concepts have employed neutron-absorbing stainless steels and nickel-based alloys in order to meet all the requirements in terms of corrosion and thermalhydraulics. In order to achieve higher burnups and extend the time between refueling in a SCW-SMR, the use of chromium-coated zirconium alloy as a potential fuel cladding candidate has been explored. Chromium coatings up to a few micrometers thick have shown improved oxidation resistance of zirconium-based claddings under operating conditions relevant to SCWR concepts. In this study, Zr-2.5Nb alloy (UNS R60904) from pressure tube samples was coated using a physical vapor-deposition (PVD) method. Oxidation tests were performed on coated samples at 500 °C and approximately 25 MPa in a refreshed autoclave. The effects of the oxide on heat transfer and hydraulic resistance are also discussed in this study. Last, but not least, this study evaluates the coating cost of the fuel cladding with chromium in a vacuum plasma spray process. Full article

Supercritical fluid extraction (SCFE) is an ever-expanding approach that can be applied both for extracting components of high commercial value from natural matrices or removal of undesirable or toxic components from many types of matrices. When it comes to the removal of contaminants from natural matrices, a great deal of research has been limited to the solid residues, where both supercritical water (SCW) and supercritical carbon dioxide (SCCO2) are valid choices for extracting medium. This review, instead, focuses on the treatment of liquid matrices by SCCO2. Full article

In the following work, the hydrothermal degradation of polypropylene waste (PP) using supercritical water (SCW) has been studied. The procedure was carried out in a high-pressure, high-temperature batch reactor at 425 °C and 450 °C from 15 to 240 min. The results show a high yield of the oil (up to 95%) and gas (up to 20%) phases. The gained oil phase was composed of alkanes, alkenes, cycloalkanes, aromatic hydrocarbons, and alcohols. Alkanes and alcohols predominated at 425 °C and shorter reaction times, while the content of aromatic hydrocarbons sharply increased at higher temperatures and times. The higher heating values (HHVs) of oil phases were in the range of liquid fuel (diesel, gasoline, crude and fuel oil), and they were between 48 and 42 MJ/kg. The gas phase contained light hydrocarbons (C₁–C₆), where propane was the most represented component. The results for PP degradation obtained in the present work were compared to the results of SCW degradation of colored PE waste, and the potential degradation mechanism of polyolefins waste in SCW is proposed. The results allowed to conclude that SCW processing technology represents a promising and eco-friendly tool for the liquefaction of polyolefin (PE and PP) waste into oil with a high conversion rate. Full article

The generation of hydrogen from unconventional oil is expected to increase significantly during the next decade. It is commonly known that hydrogen is an environmentally friendly alternative fuel, and its production would partially cover the gap in energy market requirements. However, developing new cheap catalysts for its production from crude oil is still a challenging area in the field of petroleum and the petrochemical industry. This study presents a new approach to synthesizing and applying promising catalysts based on Ni, Co, and Ni-Co alloys that are supported by aluminum oxide Al₂O₃ in the production of hydrogen from extra-heavy crude oil in the Tahe Oil Field (China), in the presence of supercritical water (SCW). The obtained catalysts were characterized via scanning electron microscopy (SEM), Brunauer-Emmett-Teller (BET) surface area analysis, transmission electron microscopy (TEM), and, X-ray diffraction analysis (XRD). The obtained XRD data showed 3.22% of Co²⁺ in the Co/Al₂O₄ catalyst, 10.89% of Ni²⁺ in the Ni/Al₂O₄ catalyst, and 1.51% of Co²⁺ and 2.42% of Ni²⁺ in the Ni-CoAl₂O₃ bimetallic catalyst. The BET measurements of the obtained catalysts showed a surface area ranging from 3.04 to 162 m²/g, an average particle size ranging from 0.037 to 0.944 µm, and micropore volumes ranging from 0.000377 to 0.004882 cm³/g. The thermal, SCW, and catalytic upgrading processes of the studied samples were conducted in a discontinuous autoclave reactor for 2 h at a temperature of 420 °C. The obtained results revealed that thermal upgrading yielded 1.059 mol.% of H₂, and SCW led to 6.132 mol.% of H₂; meanwhile, the presence of Ni-CoAl₂O₃ provided the maximal rate of hydrogen generation with 11.783 mol.%. Moreover, Ni-CoAl₂O₃ and NiAl₂O₃ catalysts have been found to possess good affinity and selectivity toward H₂ (11.783 mol.%) and methane CH₄ (40.541 mol.%). According to our results, the presence of SCW increases the yield of upgraded oil (from 34.68 wt.% to 58.83 wt.%) while decreasing the amount of coke (from 51.02 wt.% to 33.64 wt.%) due to the significant amount of hydrogen generation in the reaction zone, which reduces free-radical recombination, and thus, improves oil recovery. Moreover, the combination of SCW and the synthetized catalysts resulted in a significant decrease in asphaltene content in the upgraded oil, from 28% to 2%, as a result of the good redistribution of hydrogen over carbons (H/C) during the upgrading processes, where it increased from 1.39 to 1.41 in the presence of SCW and reached 1.63 in the presence of the Ni-CoAl₂O₃ catalyst. According to the XRD results of the transformed form of catalysts (CoNi₃S₄), after thermal processing, heteroatom removal from extra-heavy crude oil via oxidative and adsorptive desulfurization processes is promoted. These findings contribute to the expanding body of knowledge on hydrogen production from in situ unconventional oil upgrading. Full article

We focused on the functional components, antioxidant activity, skin-whitening, and anti-wrinkle properties of subcritical and supercritical water (SCW)-treated rutin. Rutin treatments were performed at the following temperature and pressure conditions: 200 °C/15 bar, 300 °C/100 bar, and 400 °C/250 bar. ABTS and DPPH radical scavenging activities and reducing power presented their highest values (1193.72 mg AAE/g, 728.73 mg AAE/g, and 0.65, respectively) at 300 °C/100 bar. The tyrosinase inhibitory activity of SCW-treated rutin was 21.72–60.05% at 1 mg/mL. The ethyl acetate fraction showed 14.91% melanin inhibitory activity at a concentration of 10 µg/mL compared to the α-MSH treatment group. The protein expression inhibition rates of MITF, tyrosinase, TRP-1, and TRP-2 in the ethyl acetate fractions were 14.05%, 72%, 93.05%, and 53.44%, respectively, at a concentration of 10 µg/mL, compared to the control. These results indicate that SCW treatment could be used to develop cosmetic materials and functional food with physiological activity, and that SCW-treated rutin can be used as a skin-whitening cosmetic material. Full article

In response to increasing energy demand, various types of organic wastes, including industrial and municipal wastewaters, or biomass wastes, are considered reliable energy sources. Wastes are now treated in supercritical water (SCW) for non-fossil fuel production and energy recovery. Considering that SCW technologies are green and energetically effective, to implement them on a large scale is a worldwide interest. However, issues related to the stability and functionality of materials used in the harsh conditions of SCW reactors still need to be addressed. Here we present an overview on materials used in the SCW technologies for energy harvesting from wastes. There are catalysts based on metals or metal oxides, and we discuss on these materials’ efficiency and selectivity in SCW conditions. We focus on processes relevant to the waste-to-energy field, such as supercritical water gasification (SCWG) and supercritical water oxidation (SCWO). We discuss the results reported, mainly in the last decades in connection to the current concept of supercritical pseudo-boiling (PB), a phenomenon occurring at the phase change from liquid-like (LL) to gas-like (GL) state of a fluid. This review aims to be a useful database that provides guidelines for the selection of the abovementioned functional materials (catalysts, catalyst supports, and sorbents) for the SCW process, starting from wastes and ending with energy-relevant products. Full article

In this study the environmental performance of a first-of-its-kind integrated process based on supercritical water gasification and oxidation (SCW-GcO), was evaluated using life cycle assessment (LCA). The process was applied to the treatment of carbon black and used oil as model wastes. Mass and energy balances were performed using Aspen Plus, and the environmental assessment was carried out through SimaPro. A “from cradle to grave” approach was chosen for the analysis, considering impact categories such as climate change, ozone depletion, human toxicity, particulate matter, land use, resource depletion, and other relevant indicators. The environmental profile of the SCW-GcO process was compared to other technologies for the treatment of dangerous wastes, solvent mixtures, and exhaust mineral oils by using the Ecoinvent database. It is shown that SCW-GcO allows for reduced impacts in different categories and the obtention of a favorable positive life cycle energy balance, achieving good environmental performance. Full article