Search Results (148)

This work aimed to advance the knowledge in the field of eco-friendly dielectrics with applicative relevance for future energy-related technologies. New multicomponent composites were prepared by using a cellulose ether/citric acid mixture as the matrix, which was gradually filled with strontium titanate nanoparticles (5–20 wt%). In this case, citric acid can act as a crosslinking agent for the polymer but also can react differently with the other counterparts from the composite as a function of the solvent used (H₂O and H₂O₂). This led to considerable differences in the morphological, thermal, optical, and electrical characteristics due to distinct solvent-driven interactions, as revealed by the infrared spectroscopy investigation. Hence, in contrast to H₂O, the oxidizing activity of H₂O₂ led to changes in the surface morphology, a greater transparency, a greater yellowness, an enhanced refractive index, and higher permittivity. These data provide new pathways to advance the optical and dielectric behavior of eco-compatible materials for energy devices by the careful selection of the composite’s components and the modulation of the molecular interactions via solvent features. Full article

This study fabricated SrTiO₃ grain boundary layer ceramics using hot isostatic pressing (HIP), achieving a remarkably high dielectric constant of 60,350 and a superior breakdown strength of 1722 kV/m. Microstructural characterization via scanning electron microscopy (SEM) and transmission electron microscopy (TEM) revealed that HIP treatment significantly refined grain size uniformity and homogenized bismuth distribution at grain boundaries, thus enhancing the interfacial barrier effect. Probe-based impedance spectroscopy elucidated the dielectric behavior and conduction mechanisms of individual grain boundaries. HIP promotes the formation of interfacial barrier layers (IBLs), significantly improving electrical performance. Compared to untreated samples (average breakdown strength: 555 kV/m), HIP-processed ceramics exhibited a threefold enhancement in breakdown strength (1722 kV/m). The treated ceramic exhibited excellent temperature stability, with TCC ≤8% over −55 to 125 °C. The optimized dielectric properties stem from HIP-induced structural modifications, including reduced oxygen vacancy concentrations and homogenized electronic distribution at grain boundaries. These findings establish a quantitative correlation between HIP parameters, grain boundary restructuring, and macroscopic performance, providing critical insights for designing high-energy-density dielectric materials. Full article

The present study aimed to investigate the interaction between strontium titanate photocatalysts and alkaline soil (solonetz) soil solutions. For this purpose, one commercially available and several synthesized strontium titanates were considered. The photocatalytic activity and material characteristics were assessed before and after immersion in the soil solutions. All samples were characterized by X-ray diffractometry (XRD), infrared spectroscopy (IR), diffuse reflectance spectroscopy (DRS), and scanning electron microscopy (SEM). After interaction with the soil solution, most of the samples became more active for phenol degradation. It was found that the crystalline structure of each sample was preserved, while the primary crystallite sizes decreased after both phenol degradation and immersion in solonetz soil solutions. Moreover, the surface of all synthesized nanostructures was covered by organic residues from either the soil solution or the by-products of phenol degradation. This was also visible from the DR spectra, as an intensive color change was observed. The bandgaps of most samples were also changed, except for the commercial material. The results imply that it is important to investigate the ecofriendly nature of any photocatalytic material, as it tends to influence the surrounding environment. This is important, as solar photocatalysis is rising among the possible methods for water purification and disinfection. Full article

This study presents a comprehensive analysis of the modifications in electronic structure and magnetism resulting from electronic excitation in pulsed laser-deposited Ba_0.7Sr_0.3Fe_xTi_(1−x)O₃ thin films, specifically for compositions with x = 0, 0.1, and 0.2. To investigate the effects of electronic energy loss (S_e) within the lattice, we performed 120 MeV Ag ion irradiation at varying fluences (1 × 10¹² ions/cm² and 5 × 10¹² ions/cm²) and compared the results with those of the pristine sample. The S_e induces lattice damage by generating ion tracks along its trajectory, which subsequently leads to a reduction in peak intensity observed in X-ray diffraction patterns. Atomic force microscopy micrographs indicate that irradiation resulted in a decrease in average grain height, accompanied by a more homogeneous grain distribution. X-ray photoelectron spectroscopy reveals a significant increase in oxygen vacancy (V_O) concentration as ion fluence increases. Ferromagnetism exhibits progressive deterioration with rising irradiation fluence. Due to the high S_e and multiple ion impact processes, cation interstitial defects are highly likely, which may overshadow the influence of V_O in inducing ferromagnetism, thereby contributing to an overall decline in magnetic properties. Furthermore, the elevated S_e potentially disrupts bound magnetic polarons, leading to a degradation of long-range ferromagnetism. Collectively, this investigation elucidates the electronic excitation-induced modulation of ferromagnetism, employing Fe impurity incorporation and irradiation techniques for precise defect engineering. Full article

To meet the stringent demands of next-generation flexible optoelectronic devices, a novel fabrication approach is employed that integrates the spray-coating of copper nanowires (Cu NWs) with the magnetron sputtering of SrTiO₃ thin films, thereby yielding SrTiO₃/Cu NWs/SrTiO₃ hybrid thin films. The incorporation of the SrTiO₃ layers results in improved optical performance, with the transmittance of the Cu NW network increasing from 83.5% to 84.2% and a concurrent reduction in sheet resistance from 16.9 Ω/sq to 14.5 Ω/sq. Moreover, after subjecting the hybrid thin films to 100 repeated tape-peeling tests and 2000 bending cycles with a bending radius of 5.0 mm, the resistance remains essentially unchanged, which underscores the films’ exceptional mechanical flexibility and robust adhesion. Additionally, the hybrid thin films are subjected to rigorous high-temperature, high-humidity, and oxidative conditions, where the resistance exhibits outstanding stability. These results substantiate the potential of the SrTiO₃/Cu NWs/SrTiO₃ hybrid thin films for integration into flexible and wearable electronic devices, delivering enhanced optoelectronic performance and long-term reliability under demanding conditions. Full article

In this manuscript, strontium barium titanate (BST) ferroelectric memory film materials for applications in the feasibility of applying to non-volatile RAM devices were obtained and compared. Solutions were synthesized with a proportional ratio and through the deposition of BST films on titanium nitride/silicon substrates using the sol–gel method, using rapid thermal annealing for defect repair and re-crystallization processing. The crystallization structure and surface morphology of annealed and as-deposited BST films were obtained by XPS, XRD, and SEM measurements. Additionally, the ferroelectric and resistive switching properties for the memory window, the maximum capacitance, and the leakage current were examined for Al/BST/TiN and Cu/BST/TiN structure memory devices. In addition, the first-order reaction equation of the decay reaction behavior for the BST film RRAM devices in the reset state revealed that $r=0.19{[O^{2-}]}^1$. Finally, the Cu/BST/TiN and Al/BST/TiN structures of the ferroelectric BST films RRAM devices exhibited good memory window properties, bipolar switching properties, and non-volatile properties for applications in non-volatile memory devices. Full article

Magnetron sputtering allows for the accurate estimation of film thickness. Strontium titanate (STO) thin films were deposited on Nb-doped STO substrates using radiofrequency magnetron sputtering technology. The microstructures and dielectric properties of STO thin films were investigated. X-ray diffraction (XRD) analysis indicates that uniform polycrystalline STO films were obtained after thermal annealing at 650 °C. The films exhibit a significant correlation between thickness, annealing temperature, and breakdown field strength. The optimal film with a thickness of 1150 nm achieves a capacitance density of 1688 pF/mm² and a breakdown field strength of 270 kV/mm. Additionally, STO films annealed at 650 °C maintained their capacitance value within ±15% across a temperature range of −55 °C to 125 °C. These results highlight the potential of STO thin films for high-performance capacitor applications. Full article

Epitaxial layers of water-soluble Sr₃Al₂O₆ were fabricated as sacrificial layers on SrTiO₃ (100) single-crystal substrates using the Pulsed Laser Deposition technique. This approach envisages the possibility of developing a new generation of micro-Solid Oxide Fuel Cells and micro-Solid Oxide Electrochemical Cells for portable energy conversion and storage devices. The sacrificial layer technique offers a pathway to engineering free-standing membranes of electrolytes, cathodes, and anodes with total thicknesses on the order of a few nanometers. Furthermore, the ability to etch the SAO sacrificial layer and transfer ultra-thin oxide films from single-crystal substrates to silicon-based circuits opens possibilities for creating a novel class of mixed electronic and ionic devices with unexplored potential. In this work, we report the growth mechanism and structural characterization of the SAO sacrificial layer. Epitaxial samarium-doped ceria films, grown on SrTiO3 substrates using Sr₃Al₂O₆ as a buffer layer, were successfully transferred onto silicon wafers. This demonstration highlights the potential of the sacrificial layer method for integrating high-quality oxide thin films into advanced device architectures, bridging the gap between oxide materials and silicon-based technologies. Full article

This paper explores the potential of phase change materials (PCM) for dynamically tuning the frequency response of a dumbbell u-slot defected ground structure (DGS)-based band stop filter. The DGSs are designed using co-planar waveguide (CPW) line structure on top of a barium strontium titanate (Ba_0.6Sr_0.4TiO₃) (BST) thin film. BST film is used as the high-dielectric material for the planar DGS. Lower insertion loss of less than −2 dB below the lower cutoff frequency, and enhanced band-rejection with notch depth of −39.64 dB at 27.75 GHz is achieved by cascading two-unit cells, compared to −12.26 dB rejection with a single-unit cell using BST thin film only. Further tunability is achieved by using a germanium telluride (GeTe) PCM layer. The electrical properties of PCM can be reversibly altered by transitioning between amorphous and crystalline phases. We demonstrate that incorporating a PCM layer into a DGS device allows for significant tuning of the resonance frequency: a shift in resonance frequency from 30.75 GHz to 33 GHz with a frequency shift of 2.25 GHz is achieved, i.e., 7.32% tuning is shown with a single DGS cell. Furthermore, by cascading two DGS cells with PCM, an even wider tuning range is achievable: a shift in resonance frequency from 27 GHz to 30.25 GHz with a frequency shift of 3.25 GHz is achieved, i.e., 12.04% tuning is shown by cascading two DGS cells. The results are validated through simulations and measurements, showcasing excellent agreement. Full article

The demand for reconfigurable devices for emerging RF and microwave applications has been growing in recent years, with additive manufacturing and photonic thermal treatment presenting new possibilities to supplement conventional fabrication processes to meet this demand. In this paper, we present the realization and analysis of barium–strontium–titanate-(Ba_0.5Sr_0.5TiO₃)-based ferroelectric variable capacitors (varactors), which are additively deposited on top of conventionally fabricated interdigitated capacitors and enhanced by photonic thermal processing. The ferroelectric solution with suspended BST nanoparticles is deposited on the device using an ambient spray pyrolysis method and is sintered at low temperatures using photonic thermal processing by leveraging the high surface-to-volume ratio of the BST nanoparticles. The deposited film is qualitatively characterized using SEM imaging and XRD measurements, while the varactor devices are quantitatively characterized by using high-frequency RF measurements from 300 MHz to 10 GHz under an applied DC bias voltage ranging from 0 V to 50 V. We observe a maximum tunability of 60.6% at 1 GHz under an applied electric field of 25 kV/mm (25 V/μm). These results show promise for the implementation of photonic thermal processing and additive manufacturing as a means to integrate reconfigurable ferroelectric varactors in flexible electronics or tightly packaged on-chip applications, where a limited thermal budget hinders the conventional thermal processing. Full article

Amidst the swift expansion of the electric vehicle industry, the imperative for alternative battery technologies that balance economic feasibility with sustainability has reached unprecedented importance. Herein, we utilized Perovskite-based oxide compounds barium titanate (BaTiO₃) and strontium titanate (SrTiO₃) nanoparticles as anode materials for lithium-ion batteries from straightforward and standard carbonate-based electrolyte with 10% fluoroethylene carbonate (FEC) additive [1M LiPF₆ (1:1 EC: DEC) + 10% FEC]. SrTiO₃ and BaTiO₃ electrodes can deliver a high specific capacity of 80 mA h g⁻¹ at a safe and low average working potential of ≈0.6 V vs. Li/Li⁺ with excellent high-rate performance with specific capacity of ~90 mA h g⁻¹ at low current density of 20 mA g⁻¹ and specific capacity of ~80 mA h g⁻¹ for over 500 cycles at high current density of 100 mA g⁻¹. Our findings pave the way for the direct utilization of perovskite-type materials as anode materials in Li-ion batteries due to their promising potential for Li⁺ ion storage. This investigation addresses the escalating market demands in a sustainable manner and opens avenues for the investigation of diverse perovskite oxides as advanced anodes for next-generation metal-ion batteries. Full article

Thin films of strontium titanate, which reveal high structure quality and tunable properties prospective for microwave applications at room temperature, were grown on a semi-insulating silicon carbide substrate using magnetron sputtering for the first time. The films’ growth mechanisms were studied using medium-energy ion scattering, and the films’ structures were investigated using X-ray diffraction. The electrical characteristics of planar capacitors based on strontium titanate films were measured at a frequency of 2 GHz using a high-precision resonance technique. It is shown that the tendency to improve the crystalline structure of strontium titanate film with an increase in the substrate temperature is most pronounced for films deposited at elevated working gas pressure under low supersaturation conditions. Planar capacitors formed on the basis of oriented SrTiO₃ films on silicon carbide showed tunability n = 36%, with a loss tangent of 0.008–0.009 at a level of slow relaxation of capacitance, which is significantly lower than the data published currently regarding planar tunable ferroelectric elements. This is the first successful attempt to realize a planar SrTiO₃ capacitor on a silicon carbide substrate, which exhibits a commutation quality factor more than 2500 at microwaves. Full article

Strontium titanate (STO) and its variants have emerged as leading materials in photocatalysis, particularly for degrading nitrogen oxides (NOx), due to their non-toxic nature, structural adaptability, and exceptional thermal stability. Although the one-pot sol-gel method leads to high-quality photocatalysts, areas remain for improvement. This study examines the impact of ethanol as a cosolvent in STO synthesis, focusing on optimizing the water-to-ethanol volume ratio. The findings reveal that a 1:3 ratio significantly enhances macropore formation and photocatalytic efficiency, achieving 42% NOx degradation under LED within three hours. Furthermore, incorporating 8.0 wt.% Ag into STO substantially improves visible light absorption and enables complete NOx elimination, thanks to enhanced charge separation and localized surface plasmon resonance. Even at high temperatures (1100 °C), the Ag-STO photocatalyst maintains partial activity, despite exceeding silver’s melting point. These results highlight the potential of STO-based materials for industrial applications, positioning them as a promising solution for effective NOx mitigation. Full article

In this study, we prepared a strontium ferrite titanate (STF) thin film using a sol–gel process to insulate resistive random-access memory (RRAM) applications. Compared to the typical strontium titanate (STO) RRAM, the improvement in the resistive switching characteristics in STF RRAM is obvious. The Al/STO/ITO/Glass RRAM set/reset voltages of −1.4 V/+3.3 V and the Al/STF/ITO/Glass RRAM set/reset voltages of −0.45 V/+1.55 V presented a memory window larger than 10³, a low operating voltage and device stability of more than 104 s. In this study, the influence of Fe on the conducting paths and the bipolar resistive switching properties of Al/STF/ITO/Glass RRAM devices is investigated. Full article

In this research, the doping of SrTiO₃ with Mn⁴⁺ was performed in order to evaluate the potential application as a photocatalyst for the degradation of organic dye pollutants. Since photocatalytic activity depends on grain microstructure, fractal analysis was used to estimate the Hausdorff dimension to provide a more thorough investigation of Mn@SrTiO₃ morphology. Structural analysis by infrared spectroscopy indicated the incorporation of Mn⁴⁺ into the SrTiO₃ lattice, while by using x-ray diffraction, the crystallite size of 44 nm was determined. The photocatalytic activity test performed on complex ethyl violet organic dye revealed potential for Mn@SrTiO₃ application in water treatment. Based on fractal regression analysis, a good estimate was obtained for the reconstruction of grain shape, with a Hasudorff dimension of 1.13679, which was used to find the best kinetics model for the photodegradation reaction. The experimental data showed a nearly linear fit with fractal-like pseudo-zero order. These findings and applications of fractal dimensions could contribute to future characterizations of photocatalysts, providing a deeper understanding of surface properties and their influence on photocatalytic activity. Full article