Search Results (796)

Quantum dots (QDs) composed of the narrow-bandgap semiconductor PbTe were incorporated into the depletion region of p–n junctions based on wide-bandgap II–VI semiconductors (p-ZnTe/n-CdTe). The heterostructures were grown by molecular beam epitaxy (MBE) on semi-insulating GaAs (100) substrates. The depletion region was engineered by depositing 20 alternating thin layers of CdTe and PbTe, then thermal annealing under ultrahigh vacuum. As revealed by cross-sectional scanning electron microscopy (SEM), the initially continuous PbTe layers transformed into arrays of zero-dimensional nanostructures, namely PbTe QDs. The formation of PbTe QDs in a CdTe matrix arises from the structural mismatch between the zinc blende and rock-salt crystal structures of the two materials. Electron beam-induced current (EBIC) scans confirmed that the QDs are localized within the depleted charge region between the p-ZnTe and n-CdTe layers. The resulting wide-gap diodes containing narrow-band QDs show pronounced sensitivity to infrared radiation in the spectral range of 1–4.5 μm, with a peak responsivity of approximately 8 V/W at a wavelength of ~2.0 μm and a temperature of 200 K. A red-shift in the cutoff wavelength when temperature decreases indicates that the infrared (IR) response is governed by band-to-band optical transitions in the PbTe QDs. In addition, the devices show sensitivity to visible radiation, with a maximum responsivity of 20 V/W at 0.69 μm. These results demonstrate that wide-bandgap p–n junctions incorporating narrow-bandgap QDs can function as dual-wavelength (visible and infrared) photodetectors, with potential applications in two-color detection and infrared solar cells. Full article

The influence of ZnO nanolayers as a passivating layer prevents electrons from recombining with the electrolyte or oxidized dye molecules at the interface by acting as a blocking layer for semiconducting materials. At 300 °C, it was observed that FTO-ZnO 500-cycle samples recorded the lowest Rq and Ra values of 1210 nm and 0.877 nm, respectively, resulting in homogeneous, crystalline, and smooth surface thin films. SEM images of FTO-ZnO 500 cycles-300 °C (150.00 KX) show a much more crystalline and homogeneous layer, while FTO-ZnO 500 cycles-100 °C (150.00 KX) show an irregular and agglomerated surface. Energy-dispersive spectroscopy also revealed that ALD successfully deposited ZnO on the FTO glass substrates, especially at 300 °C, resulting in uniform layers. In visible light wavelength (400 nm–800 nm), FTO-ZnO 500 cycles-300 °C exhibited the highest stable transmittance value of 0.78 a.u. However, it can be observed that the temperature with the slowest grain growth at 500 cycles of ZnO deposition was 200 °C, with a layer thickness of 60 nm. The device efficiency increased progressively with deposition temperature, reaching a maximum power conversion efficiency of 4.63% for ZnO films deposited at 300 °C with 500 ALD cycles. The observed enhancement is attributed to improved crystallinity, grain growth, and film uniformity at elevated deposition temperatures, which collectively enhance charge transport and reduce recombination losses. These results demonstrate that optimizing the ALD temperature is a key factor in achieving high-quality ZnO films and improved DSSC performance. Full article

Accurate real-time dosimetry is key in megavoltage radiotherapy; however, many detectors require external biasing or complex instrumentation. This study evaluated thin-film CdTe solar cells operating in photovoltaic (zero-bias) mode as medical dosimeters. Superstrate ITO/CdS/CdTe/Cu/Au devices were fabricated and irradiated with 6-MV photons from a clinical linear accelerator to 20 kGy cumulative dose. Electrical and dosimetric properties were assessed based on AM 1.5 current–voltage measurements, external quantum efficiency (EQE), dose linearity, dose-rate dependence, field-size dependence, percentage depth dose (PDD), and one-month reproducibility. With increasing dose (5–20 kGy), the open-circuit voltage and fill factor decreased by ~2–3%, the short-circuit current density by ~10%, retaining ~87% initial efficiency. Series and shunt resistances were stable, while EQE decreased uniformly (~5%), indicating degradation mainly from increased nonradiative recombination. Dose–signal linearity remained intact, and post-irradiation sensitivity loss was corrected with a single calibration factor. Dose-rate dependence was minor; low reverse bias (~3–7 V) enhanced response without nonlinearity. Field-size and PDD responses agreed with ionization chamber data within ~1%, and weekly stability was within ~1%. Parallel stacking of two cells increased signal nearly linearly. CdTe solar-cell detectors thus enable zero-bias, real-time, stable, and scalable dosimetry and strongly agree with reference standards. Full article

Dye-sensitized solar cells (DSSCs) are considered a prospective alternative to silicon-based solar cells due to their lower production cost and simpler fabrication process than conventional solar cells. DSSCs’ adjustable optical properties enable them to function effectively under diverse illumination conditions, making them ideal for powering small electronic devices in indoor environments. In DSSCs, silver nanoparticles (AgNPs) are incorporated into titanium dioxide (TiO₂) photoanodes due to their localized surface plasmon resonance (LSPR) effect, which enhances scattering and absorbing incident light and creates a strong electromagnetic field near the surface. There are diverse manufacturing methods for DSSCs, while the screen printing method is preferred because the area of the TiO₂ film can be easily customized to effectively reduce human error and make the film highly stable. In this study, eight different stacked DSSC film structures were fabricated by adding AgNPs to TiO₂ films. The TiO₂ paste with a concentration of 3 mwt% (percentage by mass) of AgNPs performed best in this study. The photovoltaic performance was evaluated using power conversion efficiency (PCE), and the results showed that the AgNP-doped film on the surface of the fluorine-doped tin oxide (FTO) glass significantly improved the photovoltaic performance. The three layers of TiO₂ doped with AgNPs achieved the highest PCE. PCE was increased since the TiO₂ film containing AgNPs became thicker and closer to the FTO substrate. The PCE of DSSCs was compared using pure TiO₂ NPs and the AgNP-doped TiO₂ photoanode. The efficiency increased from 5.67% to a maximum of 6.13%. This enhanced efficiency, driven by LSPR and improved electron transport, confirms the viability of screen-printed, plasmon-enhanced photoanodes for high-efficiency DSSCs. Full article

Dye-sensitized solar cells (DSSCs) are known for their excellent low-light performance, cost-effectiveness, and flexibility. The photoanode has a crucial role in enhancing the overall performance of DSSCs and can be modified with different nanostructures. This study explores the impact of photoanode structure on the power conversion efficiency (PCE) of DSSCs, where four configurations of freestanding TiO₂ nanotube arrays (f-TNAs), closed-up, closed-down, open-up, and open-down, were employed as photoanodes. Performance was evaluated based on current density (J_sc), open-circuit voltage (V_oc), fill factor (FF), and PCE concerning dye adsorption, electrolyte diffusion, electron transport, and barrier layer. DSSCs based on open configurations, open-up and open-down f-TNAs, demonstrated superior performance, achieving PCE of 7.73% and 7.71%, respectively. The primary distinction between the DSSCs based on open-up f-TNAs and those based on open-down f-TNAs lies in the dye adsorption time and electron diffusion characteristics. The PCE for DSSCs with closed-down f-TNAs was measured at 6.78%, while DSSCs with closed-up f-TNAs showed a lower PCE of 5.52%. The presence of a barrier layer under the bottom of f-TNAs impacted the PCE for DSSCs with closed-down f-TNAs, whereas for DSSCs with closed-up f-TNAs, insufficient dye loading, poor electrolyte diffusion and barrier layer reduced the performance. Full article

The maritime industry is under increasing pressure to reduce greenhouse gas emissions, especially in countries such as Saudi Arabia that are actively working to transition to cleaner energy. In this paper, a new hybrid shipboard power system, which incorporates wind turbines, solar photovoltaic (PV) panels, proton-exchange membrane fuel cells (PEMFCs), and a battery energy storage system (BESS) together for propulsion and hotel load services, is proposed. A multi-loop Energy Management System (EMS) based on proportional–integral control (PI) is developed to coordinate the interconnections of the power sources in real time. In contrast to the widely reported model predictive or artificial intelligence optimization schemes, the PI-derived EMS achieves similar power stability and hydrogen utilization efficiency with significantly reduced computational overhead and full marine suitability. By taking advantage of the high solar irradiance and coastal wind resources in Saudi Arabia, the proposed configuration provides continuous near-zero-emission operation. Simulation results show that the PEMFC accounts for about 90% of the total energy demand, the BESS (±0.4 MW, 2 MWh) accounts for about 3%, and the stationary renewables account for about 7%, which reduces the demand for hydro-gas to about 160 kg. The DC-bus voltage is kept within ±5% of its nominal value of 750 V, and the battery state of charge (SOC) is kept within 20% to 80%. Sensitivity analyses show that by varying renewable input by ±20%, diesel consumption is ±5%. These results demonstrate the system’s ability to meet International Maritime Organization (IMO) emission targets by delivering stable near-zero-emission operation, while achieving high hydrogen efficiency and grid stability with minimal computational cost. Consequently, the proposed system presents a realistic, certifiable, and regionally optimized roadmap for next-generation hybrid PEMFC–battery–renewable marine power systems in Saudi Arabian coastal operations. Full article

This study presents the development and characterization of Grätzel cells (DSSCs), part of third-generation photovoltaic technologies, fabricated with and without the addition of graphene nanoparticles. A TiO₂ paste was prepared by combining colloidal solutions of Polyethylene Glycol (PEG) and Titanium Tetrachloride (TiCl₄), and then deposited on FTO (Fluorine-doped Tin Oxide) glass substrates via spin coating and sensitized with N719 dye. Each cell was assembled using two FTO electrodes, a photoanode (TiO₂/N719) and a platinum-coated counter electrode, separated by a liquid iodide/triiodide-based electrolyte to complete the redox cycle. The core objective was to optimize the graphene nanoparticle concentration within the TiO₂ matrix to improve photovoltaic performance. Samples with 0.1%, 0.2%, and 0.5% graphene were tested under simulated illumination (AM 1.5G), evaluating photocurrent, efficiency, and Fill Factor (FF). Optical analysis included desorption of N719 using NaOH to quantify intrinsic light absorption. Graphene’s high transparency and charge transport properties positively affected light harvesting. Results showed that graphene dosage is critical; 0.1% yielded the best efficiency, while excess concentrations diminished electronic and optical behavior. Controlled integration of graphene nanoparticles enhances DSSC performance and supports the development of more efficient and sustainable solar cells. Full article

Algeria’s transition toward sustainable energy requires the exploitation of its abundant solar and wind resources for green hydrogen production. This study assesses the techno-economic feasibility of an off-grid PV/wind hybrid system integrated with a hydrogen subsystem (electrolyzer, fuel cell, and hydrogen storage) to supply both electricity and hydrogen to decentralized sites in Algeria. Using HOMER Pro, five representative Algerian regions were analyzed, accounting for variations in solar irradiation, wind speed, and groundwater availability. A deferrable water-extraction and treatment load was incorporated to model the water requirements of the electrolyzer. In addition, a comprehensive sensitivity analysis was conducted on solar irradiation, wind speed, and the capital costs of PV panels and wind turbines to capture the effects of renewable resource and investment cost fluctuations. The results indicate significant regional variation, with the levelized cost of energy (LCOE) ranging from 0.514 to 0.868 $/kWh, the levelized cost of hydrogen (LCOH) between 8.31 and 12.4 $/kg, and the net present cost (NPC) between 10.28 M$ and 17.7 M$, demonstrating that all cost metrics are highly sensitive to these variations. Full article

The manufacturing techniques, structural features, and optical attributes of titanium dioxide (TiO₂) nanoparticles are highlighted in this study. These nanoparticles are notable for their remarkable photocatalytic activity, cheap cost, chemical stability, and biocompatibility. TiO₂ consists of three polymorph structures: anatase, rutile, and brookite. Because of its electrical characteristics and large surface area, anatase is the most efficient for photocatalysis when exposed to UV light. The crystallinity, size, and shape of titania nanoparticles (NPs) are influenced by diverse production techniques. Sol-gel, hydrothermal, solvothermal, microwave-assisted, and green synthesis with plant extracts are examples of common methods. Different degrees of control over morphology and surface properties are possible with each approach, and these factors ultimately affect functioning. For example, microwave synthesis provides quick reaction rates, whereas sol-gel enables the creation of homogeneous nanoparticles. XRD and SEM structural investigations validate nanostructures with crystallite sizes between 15 and 70 nm. Particle size, synthesis technique, and annealing temperature all affect optical characteristics such as bandgap (3.0–3.3 eV), fluorescence emission, and UV-visible absorbance. Generally speaking, anatase has a smaller crystallite size and a greater bandgap than rutile. TiO₂ nanoparticles are used in gas sensing, food packaging, biomedical coatings, dye-sensitized solar cells (DSSCs), photocatalysis for wastewater treatment, and agriculture. Researchers are actively exploring methods like adding metals or non-metals, making new composite materials, and changing the surface to improve how well they absorb visible light. Full article

Titanium dioxide (TiO₂) is widely used in solar cells and photocatalysts, given its excellent photoactivity, low cost, and high structural, electronic, and optical stability. Here, a novel TiO₂ composite was prepared by coating TiO₂ inverse opal (IO) with TiO₂ nanorods (NRs). With a porous three-dimensional network structure, the composite exhibited higher light absorption; enhanced the separation of the electron–hole pairs; deepened the infiltration of the electrolyte; better transported and collected charge carriers; and greatly improved the power conversion efficiency (PCE) of the quantum-dot sensitized solar cells (QDSSCs) based on it, while also boosting its own photocatalytic hydrogen generation efficiency. A very high PCE of 12.24% was achieved by QDSSCs utilizing CdS/CdSe sensitizer. Furthermore, the TiO₂ composite exhibited high photocatalytic activity with a H₂ release rate of 1080.2 μ mol h⁻¹ g⁻¹, several times that of bare TiO₂ IO or TiO₂ NRs. Full article

Advancements in flexible, low-cost, and recyclable alternatives to transparent conductive oxides (TCOs) are critical challenges in the sustainability of third-generation solar cells. This work introduces a copper mesh-based transparent electrode for dye-sensitized solar cells, replacing conventional fluorine doped-tin oxide (FTO)-coated glass to simultaneously reduce spectral reflection losses, enhance mechanical flexibility, and enable material recyclability. Titanium dioxide (TiO₂) photoanodes were synthesized and directly deposited onto the mesh via a single-step, low-energy ball milling process, which eliminates TiO₂ paste preparation and high-temperature annealing while reducing fabrication time from over three hours to 30 min. Structural and surface analyses confirmed the deposition of high-purity anatase-phase TiO₂ with strong adhesion to the mesh branches, enabling improved dye loading and electron injection pathways. Optical studies revealed higher visible light absorption for the copper mesh compared to FTO in the visible range, further enhanced upon TiO₂ and Ru-based dye deposition. Electrochemical measurements showed that TiO₂/Cu mesh electrodes exhibited significantly higher photocurrent densities and faster photo response rates than bare Cu mesh, with dye-sensitized Cu mesh achieving the lowest charge transfer resistance in impedance analysis. Techno–economic and sustainability assessments revealed a decrease of 7.8% in cost and 82% in CO₂ emissions associated with the fabrication of electrodes as compared to conventional TCO electrodes. The synergy between high conductivity, transparency, mechanical durability, and a scalable, recyclable fabrication route positions this architecture as a strong candidate for next-generation dye-sensitized solar modules that are both flexible and sustainable. Full article

This work focuses on research into innovative lead-free perovskite materials to be employed as a sensitive layer for a new generation of solar cells, exploiting their potential applications in covering greenhouses to move toward an eco-friendly environment. Two types of lead-free perovskites—yellow and orange double-cation Cs₂AgBiBr₆, synthesized with an innovative method without chemical thinners—have been used, for the first time, as a cover for greenhouses in indoor experiments by analyzing the incident electromagnetic radiation. Two plant species, Solanum lycopersicum L. and Artemisia annua L., were cultivated indoors under controlled light, temperature, and humidity, covering the greenhouses with yellow (PY+) and orange (PO+) panels for comparison with control plants (P−) roofed by a glass panel. The growth and development parameters of all plants were investigated, referring to the aerial and root parts. Significant differences were found in terms of the plant growth parameters and photosynthetic pigments of both PY+ and PO+ compared to P− and also between them, with the yellow panel being less invasive. These results, dealing with two different plant species, confirm the feasibility of using perovskite-based panels for indoor cultivation and pave the way for outdoor application in greenhouses under sunlight. Full article

This paper introduces a power-driven systems engineering methodology for the early-phase design of highly miniaturized satellites: PlanarSats. We derive an analytical framework linking power requirements, contingency policies, solar-cell performance, and subsystem integration to determine the absolute minimum satellite size. Through idealized and detailed case studies, we explore the trade-offs inherent in subsystem selection and integration constraints. Sensitivity analysis identifies critical factors affecting minimum area and operational envelopes. Our framework provides a clear tool for balancing functionality, reliability, and physical limits in next-generation ultra-small satellite missions. Full article

Perovskite solar cells (PSCs) are next-generation solar cells; they are replacing silicon-based solar cells due to their higher efficiency, greater cost-effectiveness, and enhanced potential for various applications. Exceeding the efficiency of crystalline silicon-based solar cells, the commercialization of PSCs has driven not only the development of perovskite photoactive materials but also charge transport layer advancements, interfacial engineering, and processing technologies. PSCs were developed later than dye-sensitized solar cells and organic solar cells; the adoption of techniques previously employed in these technologies is significant to enhancing their performance. Among them, polymers are widely employed in perovskite solar cells to facilitate efficient charge transport, provide interfacial passivation, enhance mechanical flexibility, enable solution-based processing, and improve environmental stability. In this review, we highlight the roles of polymer materials as charge transport layers, interfacial layers, and other functional layers for highly efficient and stable PSCs. Full article

Binary oxide ceramics have emerged as key materials in solar energy research due to their versatility, chemical stability, and tunable electronic properties. This study presents a comparative analysis of seven prominent oxides (TiO₂, ZnO, Al₂O₃, SiO₂, CeO₂, Fe₂O₃, and WO₃), focusing on their functional roles in silicon, perovskite, dye-sensitized, and thin-film solar cells. A bibliometric analysis covering over 50,000 publications highlights TiO₂ and ZnO as the most widely studied materials, serving as electron transport layers, antireflective coatings, and buffer layers. Al₂O₃ and SiO₂ demonstrate highly specialized applications in surface passivation and interface engineering, while CeO₂ offers UV-blocking capability and Fe₂O₃ shows potential as an absorber material in photoelectrochemical systems. WO₃ is noted for its multifunctionality and suitability for scalable, high-rate processing. Together, these findings suggest that binary oxide ceramics are poised to transition from supporting roles to essential components of stable, efficient, and environmentally safer next-generation solar cells. Full article