Search Results (96)

Façade systems in hot, high-insolation climates are required to simultaneously mitigate cooling loads, ensure high-quality daylight, and, where feasible, harvest on-site electricity demands that are often in tension. This study assesses and compares two efficient façade strategies for a fully glazed office prototype in Hail, Saudi Arabia: semi-transparent photovoltaic glazing (STPV10–30%VLT) and parametrically tuned split louvers (18 depth–spacing–tilt configurations). Using a unified parametric workflow (Rhino/Grasshopper), Radiance/honeybee for daylight metrics, ASHRAE-55 heat-balance metrics for thermal comfort, and EnergyPlus for end-use and PV yield, to evaluate annual and solstice performance across cardinal orientations. Optimized split louvers maintained UDI_300–1000lx and effectively suppress glare, but incur substantial lighting-energy penalties. In contrast, STPV with 10–20% VLT broadly meets daylight targets while strongly reducing cooling and lighting demand, delivering whole-façade energy savings of up to 50–94% depending on orientation, but could be net-neutral to slightly adverse north 3% when daylight penalties dominate. Thermal comfort responses mirrored these trends: summer PMV was near 0 to +0.5 for both systems, with winter under-heating evident when solar gains are strongly suppressed. Overall, in hot-arid, highly glazed offices, STPV of 10–20%VLT provides the most balanced triad of daylight quality, cooling reduction, and net energy benefit, while optimized louvers excel where glare control is paramount but require careful daylight-control integration. Full article

Buildings account for nearly 40% of global energy consumption, mainly due to the demands of artificial lighting and heating, ventilation, and air-conditioning (HVAC) systems. The integration of semi-transparent photovoltaic (STPV) modules into building envelopes presents a sustainable strategy to lower energy use while simultaneously replacing conventional roofs and façades. However, the performance of STPV systems is strongly influenced by incident solar radiation and building orientation, and elevated surface temperatures can further diminish their efficiency. In this study, the performance of an STPV module was assessed by placing it on a horizontal surface and varying its orientation relative to a 90° reference. To mitigate thermal effects and improve efficiency, a thermal management system incorporating a calcium chloride hexahydrate-based phase change material (PCM) was employed. The PCM was enhanced with nanomaterials—graphene oxide (GO) and aluminum oxide (Al₂O₃)—at weight fractions of 0%, 0.25%, 0.5%, and 1%. The thermophysical properties of the nano-enhanced PCM were analyzed using differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), and thermal conductivity measurements. Under incident solar radiation of 941 W/m², the electrical efficiencies of the PV, PV–PCM1, and PV–PCM2 modules were measured at 13.75%, 16.84%, and 15.28%, respectively, demonstrating the potential of nano-enhanced PCM to improve STPV performance. Full article

The use of semi-transparent photovoltaic (Solar PV) glass in buildings is an effective strategy for integrating renewable energy generation, solar control, and thermal comfort. However, conventional simulation models rely on global optical properties, neglecting spectral radiation and its propagation within the material. This limits the accurate assessment of thermal comfort, light distribution, and performance in complex systems such as multi-layer glazing. This study presents the development, implementation, and experimental validation of a numerical model that reproduces the thermal, electrical, and optical behaviour of semi-transparent Solar PV glass, explicitly incorporating radiative transfer. The model simultaneously solves the conduction, convection, and electrical generation equations together with the radiative transfer equation, solved via the finite volume method across two spectral bands. The refractive index and extinction coefficient, derived from manufacturer-provided optical data, were used as inputs. Experimental validation employed 10% semi-transparent a-Si glass, comparing surface temperatures and electrical power generation. The model achieved average relative errors of 3.8% for temperature and 3.3% for electrical power. Comparisons with representative literature models yielded errors between 6% and 21%. Additionally, the proposed model estimated a solar factor of 0.32, closely matching the manufacturer’s 0.29. Full article

All inorganic CsPbBr₃ possesses ideal stability in halide perovskites, but its wide bandgap and relatively poor film quality seriously limit the performance enhancement and possible applications of perovskite solar cells (PSCs). In this work, a triple-functional poly(3-Hexylthiophene) (P3HT) modifier was introduced to realize color-tunable semi-transparent CsPbBr₃ PSCs. From the optical perspective, the P3HT acted as the assistant photoactive layer, enhanced the light absorption capacity of the CsPbBr₃ film, and broadened the spectrum response range of devices. In view of the hole transport layer, P3HT modified the energy level matching between the CsPbBr₃/anode interface and facilitated the hole transport. Simultaneously, the S⁻ in P3HT formed a more stable Pb-S bond with the uncoordinated Pb²⁺ on the surface of CsPbBr₃ and played the role of a defect passivator. As the P3HT concentration increased from 0 to 15 mg/mL, the color of CsPbBr₃ devices gradually changed from light yellow to reddish brown. The PSC treated by an optimal P3HT concentration of 10 mg/mL achieved a champion power conversion efficiency (PCE) of 8.71%, with a V_OC of 1.30 V and a J_SC of 8.54 mA/cm², which are remarkably higher than those of control devices (6.86%, 1.22 V, and 8.21 mA/cm²), as well its non-degrading stability and repeatability. Here, the constructed CsPbBr₃/P3HT heterostructure revealed effective paths for enhancing the photovoltaic performance of CsPbBr₃ PSCs and boosted their semi-transparent applications in building integrated photovoltaics (BIPVs). Full article

The integration of photovoltaic (PV) panels in greenhouses enables dual land use, combining crop production with electricity generation. However, PV installations can reduce both the intensity and uniformity of light at the canopy level, potentially affecting crop growth. This study employed computational fluid dynamics (CFD) simulations to evaluate the effects of different layouts of commercial-size thin PV modules—both opaque and semi-transparent—installed at gutter height in greenhouses on irradiance and, in particular, on its distribution within the greenhouse. Achieving a homogeneous distribution of light is critical for effective plant growth beneath photovoltaic systems. The influence of greenhouse size and roof shape on the intensity and uniformity of visible radiation was investigated as well. The results showed that during winter (21 December), irradiance in a mono-span tunnel greenhouse was 4–6% higher than in a multi-span large structure; in summer (21 June), this difference increased to 10–13%. Among the opaque PV layouts tested, the north–south (NS) straight-line arrangement provided the most uniform light distribution, outperforming the checkerboard and east–west (EW) layouts. The EW straight-line layout was the least effective regarding light uniformity. Roof shape (arched vs. pitched) had minimal impact on radiation distribution. Semi-transparent PV modules consistently resulted in 17% higher irradiance and more uniform light distribution than opaque ones. These findings can inform efficient PV deployment strategies in greenhouses to enhance both energy yield and crop productivity. Full article

Transparent conductive aluminum-doped zinc oxide (AZO) films were investigated as potential recombination layers for perovskite/silicon tandem solar cells, comparing the results of atomic layer deposition (ALD) and magnetron sputtering (MS) on vertically aligned silicon nanowire (SiNW) scaffolds. Conformality and thickness control were examined by cross-sectional SEM/TEM and profilometry, revealing fully conformal ALD coatings with tunable thicknesses (40–120 nm) versus tip-capped, semi-uniform MS films (100–120 nm). Optical transmission measurements on glass substrates showed that both 120 nm ALD and MS layers exhibit interference maxima near 450–500 nm and 72–89% transmission across 800–1200 nm; the thinnest ALD films reached up to 86% near-IR transparency. Four-point probe analysis demonstrated that ALD reduces surface resistance from 1150 Ω/□ at 40 nm to 245 Ω/□ at 120 nm, while MS layers achieved 317 Ω/□ at 120 nm. These results delineate the balance between conformality, transparency, and conductivity, providing design guidelines for AZO recombination interfaces in next-generation tandem photovoltaics. Full article

Building-integrated photovoltaic (BIPV) windows present a viable path towards carbon neutrality in the building sector. However, conventional BIPV windows, such as semi-transparent photovoltaic (STPV) glazings, still suffer from inadequate thermal insulation, which limits their effectiveness across different climate conditions. To address this issue, the cadmium telluride-based vacuum PV glazing has been developed to enhance the thermal performance of BIPV applications. To fully understand the complex thermal behaviour under real-world operational scenarios, this study introduces a one-dimensional transient heat transfer model that can efficiently capture the time-dependent thermal dynamics of this novel glazing system. Based on the numerical solutions using the explicit finite difference method (FDM), the temperature profile of the vacuum PV glazing can be obtained dynamically. Consequently, the heat gain of the semi-transparent vacuum PV glazing can be calculated under time-varying outdoor and indoor conditions. The validated heat transfer model was applied under four different scenarios, viz. summer daytime, summer nighttime, winter daytime, and winter nighttime, to provide a detailed analysis of the dynamic thermal behaviour, including the temperature variation and the energy flow. The dynamic thermal characteristics of the vacuum PV glazing calculated by the transient heat transfer model demonstrate its excellent thermal insulation and solar control capabilities. Moreover, the thermal performance of vacuum PV glazing was compared with a standard double-pane window under various weather conditions of a typical summer day and a typical winter day. The results indicate that the vacuum PV glazing can effectively minimise both heat gain and heat loss. The fluctuation of the inner surface temperature can be controlled within a limited range away from the set point of the indoor room temperature. Therefore, the vacuum PV glazing contributes to stabilising the temperature of the indoor environment despite the fluctuating solar radiation and periodic outdoor temperature. It is suggested that the vacuum PV glazing has the potential to enhance the climate adaptability of BIPV windows under different climate backgrounds. Full article

Semitransparent perovskite solar cells (PSCs) that possess a high-power conversion efficiency (PCE) and high average visible light transmittance (AVT) can be employed in applications such as photovoltaic windows. In this study, a bifacial modification comprising a buried layer of [4-(3,6-Dimethyl-9H-carbazol-9-yl) butyl] phosphonic acid (Me-4PACz) and a surface passivator of 2-(2-Thienyl) ethylamine hydroiodide (2-TEAI) was proposed to enhance device performance. When the concentrations of Me-4PACz and 2-TEAI were 0.3 mg/mL and 3 mg/mL, opaque PSCs with a 1.57 eV perovskite absorber achieved a PCE of 22.62% (with a V_OC of 1.18 V) and retained 88% of their original value after being stored in air for 1000 h. By substituting a metal electrode with an indium zinc oxide electrode, the resulting semitransparent PSCs showed a PCE of over 20% and an AVT of 9.45%. It was, therefore, suggested that the synergistic effect of Me-4PACz and 2-TEAI improved the crystal quality of perovskites and the carrier transport in devices. When employing an absorber with a wider bandgap (1.67 eV), the corresponding PSC obtained a higher AVT of 20.71% and maintained a PCE of 18.73%; these values show that a superior overall performance is observed compared to that in similar studies. This work is conductive to the future application of semitransparent PSCs. Full article

In the context of rapid decarbonization, photovoltaics (PV) has played a key role. Traditionally, PV installations require large land areas, leading to competition between PV and agriculture for land use. This conflict must be addressed as the demand for both energy and food continues to rise. Additionally, it poses broader challenges, potentially leading local communities to perceive PV energy production as a threat to their economic activities and food security. An emerging and promising solution is agrivoltaics (AV), a combination of agriculture and PV. AV comes in many different forms, ranging from the simple coexistence of crops and PV installations on the same patch of land to a full synergy of the two, producing better crops while also harvesting energy from the sun. This paper paints a complete picture of the scientific work produced so far throughout the field, with special attention to the use of third-generation PV and luminescent solar concentrators (LSCs). Both technologies minimize shading and enable wavelength selection and enrichment (when functionalized with fluorescent materials) to better align with the photosynthetic needs of plants. The viability of AV has also been evaluated from an economic standpoint. This work aims to assess the current landscape of AV research and to point out possible future developments. It also seeks to evaluate whether the advantages of semi-transparent devices are substantial enough to justify their development and employment on a scale comparable to traditional PV. Full article

The increasing demand for food and energy presents challenges for agricultural and energy sustainability, especially in regions with limited arable land. This study analyzed the productivity and morphological adaptations of Phaseolus vulgaris L. in agrivoltaic systems using monofacial, bifacial, and semi-transparent photovoltaic technologies under the high Andean climatic conditions of Chachapoyas, Amazonas, Peru. The evaluated varieties, Panamito and Chaucha, were cultivated with planting distances of 25 cm and 35 cm. The analyzed variables included plant height, number of trifoliate leaves, number of flowers, number and weight of pods, grain weight, and yield. The experiment was designed with plots under agrivoltaic systems and a conventional system as a control. Environmental parameters such as photosynthetically active radiation (PAR), irradiance, precipitation, leaf moisture, soil moisture, and ambient temperature were monitored. Results showed that the bifacial system with a planting density of 25 cm was the most efficient, recording a plant height of 139.38 cm, an average grain weight of 67.97 g, and a yield of 700.5 kg/ha, significantly surpassing the conventional system. These findings shows the potential of agrivoltaic systems to enhance agricultural production by efficiently utilizing solar radiation and land, providing an innovative solution for integrating agriculture and energy generation, as well as increasing productivity in scenarios with land-use competition and climatic challenges. Full article

Despite the huge progress achieved in the optimization of perovskite solar cell (PSC) performance, stability remains a limiting factor for technological commercialization. Here, a study on the photovoltaic, structural and morphological stability of semi-transparent formamidinium lead bromide-based PSCs is presented. This work focuses on the positive role of 2D nanoscale layer passivation, induced by perovskite surface treatment with a mixture of iso-Pentylammonium chloride (ISO) and neo-Pentylammonium chloride (NEO). In situ X-ray diffraction (XRD) is applied in combination with atomic force microscopy (AFM), and the results are correlated to the devices’ photovoltaic performances. The superior power conversion efficiency and overall stability of the ISO-NEO system is evidenced, as compared to the un-passivated device, under illumination in air. Furthermore, the role of the ISO-NEO treatments in increasing the morpho-structural stability is clarified as follows: a bulk effect resulting in a protective role against the loss in crystallinity of the perovskite 3D phase (observed only for the un-passivated device) and an interface effect, being the observed 2D phase crystallinity loss spatially localized at the interface with the 3D phase where a higher concentration of defects is expected. Importantly, the complete stability of the device is achieved with the passivated ISO-NEO-encapsulated device, allowing us to exclude the intrinsic degradation effects. Full article

Long-term reliability is crucial for the commercialization of semi-transparent photovoltaic panels based on Luminescent Solar Concentrators (LSCs). This study addresses key challenges such as photodegradation and hail resistance using glazed LSC prototypes functionalized with organic Lumogen F dyes. A pilot-scale batch of LSC prototypes (10 × 10 cm²) underwent extensive outdoor exposure tests following the IEC 62108 “10.15 Outdoor Exposure Test” to evaluate long-term stability under natural solar radiation. Continuous monitoring revealed that prototypes with Lumogen F Red 305 experienced a 29% efficiency drop initially, which stabilized over time, indicating potential long-term stability. In contrast, those with Lumogen F Violet 570 showed minimal degradation, with only a 9% efficiency reduction. Additionally, the hail resistance of LSC panels was tested using the IEC 62108 “10.9 Hail Impact Test”. Panels with varying glass thickness, tempering methods, and surface areas were subjected to impact from 25 mm hailstones launched at 22.4 ± 5% m/s. All samples remained undamaged, highlighting their excellent hail resistance, a critical feature for preserving performance despite potential surface damage. This study demonstrates that combining glazed lightguides with polyvinyl butyral improves photostability and provides a cost-effective alternative to expensive fluorophores, while ensuring compliance with hail resistance standards. Full article

In the context of climate change and the increasing demand for innovative solutions in agriculture and energy, agrivoltaic systems (AVSs) have emerged as promising technologies. These systems integrate photovoltaic panels with agricultural practices, optimizing both food and energy production. This study provides a comprehensive review focused on monitoring techniques applicable to AVS, including fixed sensors and remote monitoring tools. Bibliographic analysis revealed a significant increase in scientific interest in AVSs since 2019, with most publications focusing on technological, agronomic, and environmental aspects. Key findings highlight environmental benefits such as reduced greenhouse gas emissions, improved water efficiency, and enhanced soil quality. Otherwise, challenges including high initial costs and the persistence of technical complexities. Innovative configurations such as semi-transparent or vertically bifacial panels enable resource optimization and improved agricultural yields if combined with advanced monitoring systems. This study highlights the importance of incentive policies and further research to maximize the potential of AVSs in promoting sustainable land management. Full article

Due to limited roof area, photovoltaic (PV) has gradually been installed on other facades of buildings. This research investigates the practical application of a lightweight PV curtain wall. We use EnergyPlus to build a base office building model of fit with a lightweight PV curtain wall. The performance of two typical lightweight PV curtain wall modules is evaluated in five sample Chinese cities of different climates. Simulations were carried out to determine the power generation of faux architectural material PV curtain wall modules (FAM PVCWMs) for the best cavity distance per facade in various cities. We discovered that, in Harbin, Beijing, and Shanghai, the capacity of PV curtain wall modules installed on the south facade is the best, while in Chengdu and Guangzhou, it is the west facade. We also analyzed the power generation and the impact on the indoor environment when installing semi-transparent PV curtain wall modules (ST PVCWMs). Compared with glass, the ST PVCWM’s power generation increased by at least 50%, while the glare index setpoint exceeded time reduced by at least 30.19%. Furthermore, when installed on the north facade of Chengdu and similar cities, it can ensure more than 50% of daylight indexed time and create a more favorable indoor environment. Full article

This research addresses the need for enhanced thermal management in building-integrated photovoltaic systems, specifically focusing on semi-transparent PV panels based on luminescent solar concentrator (LSC) technology. In pursuit of optimal thermal regulation, the cooling effect of a paraffin PCM was investigated via finite element simulations developed with COMSOL Multiphysics. The PCM was thermally coupled with the PV cells situated in the frame of a south-facing window. Due to the seasonal difference between winter and summer, the PCM latent heat capacity and melting temperature were optimized to ensure the maximum nominal operating cell temperature (NOCT) reduction during summer months. PCM latent heat capacities equivalent to 120 kJ/kg, 180 kJ/kg, and 240 kJ/kg have been investigated, whereas for the melting temperature a range from 20 °C to 42 °C was spanned. The combination of higher latent heat and 36 °C melting point showed the most significant thermal benefits, by reducing the NOCT from 42 °C to 36 °C, which led to an 11.80% increase in power output across the whole PV window. Considering the same latent heat, the other melting temperature resulted in more moderate benefits, namely an enhancement of 7.88% and 3.94%, for 38 °C and 40 °C, respectively. The lower latent heat capacities resulted in an NOCT reduction that ranged between 2.7 °C and 5.3 °C, according to the associated melting point. These results testify that the presented solution could significantly enhance energy production in semi-transparent PV applications based on LSC panels. Full article