Search Results (188)

Wood polymer composites (WPCs) represent a rapidly growing class of sustainable materials, formed by combining lignocellulosic fibers with thermoplastic or thermoset polymeric matrices. This review summarizes the state of the art in WPC development, emphasizing the use of recyclable (or recycled) and biodegradable polymers as matrix materials. The integration of waste wood particles into the production of WPCs addresses global environmental challenges, including plastic pollution and deforestation, by offering an alternative to conventional wood-based and petroleum-based products. Key topics covered in the review include raw material sources, fiber pre-treatments, compatibilizers, mechanical performance, water absorption behavior, thermal stability and end-use applications. Full article

Geopolymers, as an eco-friendly alternative construction material to ordinary Portland cement (OPC), exhibit superior performance in soil stabilization. However, their inherent brittleness limits engineering applications. To address this, polyethylene terephthalate (PET) fibers can be incorporated into a one-part geopolymer (OPG) binder to enhance ductility while promoting plastic waste recycling. However, the evaluation of ductile behavior of OPG-stabilized soil with PET fiber normally demands extensive laboratory and field experiments. Leveraging artificial intelligence, a predictive model can be developed for this purpose. In this study, data were collected from compressive and tensile tests performed on the OPG-stabilized soil with PET fiber. Four deep learning neural network models, namely ANN, BPNN, CNN, and LSTM, were then used to construct prediction models. The input parameters in the model included the fly ash (FA) dosage, dosage and length of the PET fiber, and the Curing Time. Results revealed that the LSTM model had the best performance in predicting the three ductile properties (i.e., the compressive strength index [UCS], strain energy index [CSE], and tensile strength index [TES]). The SHAP and 2D-PDP methods were further used to verify the rationality of the LSTM model. It is found that the Curing Time was the most important factor for the strength and ductile behavior. The appropriate addition of PET fiber of a certain length had a positive impact on the ductility index. Thus, for the OPG-stabilized soil, the optimal dosage and length of PET fiber were found to be 1.5% and 9 mm, respectively. Additionally, there was a synergistic effect between FA and PET on the ductility metric. This research provides theoretical support for the application of geopolymer and PET fiber in enhancing the ductility of the stabilized soil. Full article

Alkali-activated building materials have attracted the interest of many researchers due to their low cost and eco-efficiency. Different binders with different chemical compositions can be used for their production, so the reaction mechanism can become complex and the results of studies can vary widely. In this work, several alkali-activated mortars based on marginal by-products as binders, such as high calcium fly ash and ladle furnace slag, are investigated. Their mechanical (flexural and compressive strength, ultrasonic pulse velocity, and modulus of elasticity) and physical (porosity, absorption, specific gravity, and pH) properties were determined. After evaluating the mechanical performance of the mortars, the optimum mixture containing fly ash, which reached 15 MPa under compression at 90 days, was selected for the production of precast compressed slabs. Steel or glass fibers were also incorporated to improve their ductility. To reduce the density of the slabs, 60% of the siliceous sand aggregate was also replaced with recycled polyethylene terephthalate (PET) plastic aggregate. The homogeneity, density, porosity, and capillary absorption of the slabs were measured, as well as their flexural strength and fracture energy. The results showed that alkali activation can be used to improve the mechanical properties of weak secondary binders such as ladle furnace slag and hydrated fly ash. The incorporation of recycled PET aggregates produced slabs that could be classified as lightweight, with similar porosity and capillary absorption values, and over 65% achieved strength compared to the normal weight slabs. Full article

Traditional stabilization techniques, such as lime and cement, widely used for their effectiveness, albeit with economic and environmental limitations, are leading to the search for sustainable approaches that utilize agricultural and industrial waste, such as rice husk ash, bagasse, and natural fibers. These have been shown to improve key geotechnical properties, even under saturated conditions, significantly. In particular, the combination of rice husk ash and recycled ceramics has shown notable results in Ecuadorian coastal soils. The article emphasizes the importance of selecting techniques that balance effectiveness, cost, and sustainability and identifies existing limitations, such as the lack of long-term data (ten years) and predictive models adapted to the Ecuadorian climate. From a bibliographic perspective, this article analyzes the challenges posed by expansive soils in the western coastal region of Ecuador, whose high plasticity and instability to moisture negatively affect civil works such as roads and buildings. The Ecuadorian clay contained 30% kaolinite and only 1.73% CaO, limiting its chemical reactivity compared to soils such as Saudi Arabia, which contained 34.7% montmorillonite and 9.31% CaO. Natural fibers such as jute, with 85% cellulose, improved the soil’s mechanical strength, increasing the UCS by up to 130%. Rice husk ash (97.69% SiO₂) and sugarcane bagasse improved the CBR by 90%, highlighting their potential as sustainable stabilizers. All of this is contextualized within Ecuador’s geoenvironmental conditions, which are influenced by climatic phenomena such as El Niño and La Niña, as well as global warming. Finally, it is proposed to promote multidisciplinary research that fosters more efficient and environmentally responsible solutions for stabilizing expansive soils. Full article

The burgeoning crisis of plastic waste accumulation necessitates innovative approaches towards sustainable packaging solutions. Polylactic acid (PLA), a leading biopolymer, emerges as a promising candidate in this realm, especially for environmentally friendly packaging. PLA is renowned for its compostable properties, offering a strategic avenue to mitigate plastic waste. However, its dependency on specific industrial composting conditions, characterized by elevated temperatures, humidity, and thermophilic microbes, limits its utility for household composting. This study aims to bridge the research gap in PLA’s recyclability and explore its feasibility in mechanical recycling processes. The research focuses on assessing the mechanical characteristics of PLA and PLA-based composites post-recycling. Specifically, we examined the effects of two extrusion methods—conical and parallel—on PLA and its composites containing 20 wt.% basalt fibers (BF). The recycling process encompassed repeated cycles of hot melt extrusion (HME), followed by mechanical grinding to produce granules. These granules were then subjected to injection moulding (IM) after 1, 3 and 5 recycling cycles. The tensile properties of the resulting IM-produced bars provided insights into the material’s durability and stability. The findings reveal that both PLA and PLA/BF composites retain their mechanical integrity through up to 5 cycles of mechanical recycling. This resilience underscores PLA’s potential for integration into existing recycling streams, addressing the dual challenges of environmental sustainability and waste management. The study contributes to the broader understanding of PLA’s lifecycle and opens new possibilities for its application in eco-friendly packaging, beyond the limits of composting. The implications of these findings extend towards enhancing the circularity of biopolymers and reducing the environmental footprint of plastic packaging. Full article

This study presents a new approach to chemical processing using pyridine-based solvolysis to produce high-quality glass fiber from epoxy composites. Pyridine was chosen due to its solubility parameter, which precisely matches the parameters calculated for the epoxy matrix segment. Experiments with exposure in a pyridine medium demonstrated effective swelling and the potential for destruction. The solvolysis experiments were conducted in a round-bottomed flask with a reflux condenser and stirrer, under ambient conditions (20 °C) until the boiling point was reached (115.2 °C). Additionally, data from experimental studies conducted at subcritical temperatures before reaching 280 °C are presented. The dependences of changes in the mass of composites on time and temperature during the solvolysis process were determined. The tensile strength of the recovered fibers was examined, and thermogravimetric analysis was used to determine their properties. Fiberglass recovered at the boiling point is characterized by 91% tensile strength and 20% residual degradation products on the surface. The residual strength of fiberglass-reinforced plastic (FGRP) is 70.3%. The use of subcritical pyridine helps improve the quality of plastic products made from recycled fibers. This process retains 93% of the residual tensile strength for fibers that have been processed at 250 °C for two hours. Recycled fibers also contain 2.82% organic components on their surfaces. Using this material results in an increase in flexural strength of FGRP by 16.1%, compared to the reference samples. Full article

This paper presents an experimental investigation of six different types of composite sandwich panels manufactured from waste-based materials, which are comprised of two different types of skins (made from hemp and recycled PET (Polyethylene terephthalate) fabrics with bio-epoxy resin) and three different cores (composite wood, recycled plastic, and styrofoam) materials. The skins of these sandwich panels were investigated under five different environmental conditions (normal air, water, hygrothermal, saline solution, and 80 °C elevated temperature) over seven months to evaluate their durability performance. In addition, the tensile and dynamic mechanical properties of those sandwich panels were studied. The bending behavior of cores and sandwich panels was also investigated and compared. The results indicated that elevated temperatures are 30% more detrimental to fiber composite laminates than normal water. Composite laminates made of hemp are more sensitive to environmental conditions than composite laminates made of recycled PET. A higher-density core makes panels more rigid and less susceptible to indentation failure. The flexible plastic cores are found to be up to 25% more effective at increasing the strength of sandwich panels than brittle wood cores. Full article

Recycling carbon-fiber-reinforced plastics (CFRPs) is crucial for sustainable material utilization, particularly in aerospace applications, where large quantities of prepreg waste are generated. This study investigated the mechanical properties of highly oriented recycled CFRP (rCFRP) molded using vacuum-assisted resin transfer molding (VaRTM), wet-layup, and traditional RTM methods. Recycled carbon fibers (rCFs) obtained via solvolysis and pyrolysis were processed into nonwoven preforms to ensure fiber alignment through carding. The influence of molding methods, fiber recycling techniques, and fiber orientation on mechanical performance was examined through tensile tests, fiber volume fraction (Vf) analysis, and scanning electron microscopy observations. The results indicated that the solvolysis-recycled rCF exhibited superior interfacial adhesion with the resin, leading to a higher tensile strength and stiffness, particularly in the RTM process, where a high Vf was achieved. Wet-layup molding effectively reduced the void content owing to autoclave curing, maintaining stable properties even with pyrolyzed rCF. VaRTM, while enabling vacuum-assisted resin infusion, exhibited a higher void content, limiting improvements in mechanical performance. This study highlights that tailoring the molding method according to the desired performance, such as increasing stiffness potential by enhancing Vf in RTM or improving tensile strength by improving fiber–matrix adhesion in wet-layup molding, is critical for optimizing rCFRP properties, providing important insights into sustainable CFRP recycling and high-performance material design. Full article

In this study, a microwave-assisted sulfuric acid recovery method is proposed for the efficient recovery of high-value carbon fibers at 100–140 °C. The recycled carbon fibers (RCF) were characterized, and recycled carbon fiber-reinforced plastics (RCFRP) were fabricated using their fibers. The recycling process preserved the surface morphology of the carbon fibers, with the RCF maintaining the axial groove structure on the surface of the virgin carbon fiber (VCF). X-ray diffraction (XRD) and Raman spectroscopy analyses confirmed that the degree of graphitization and crystalline structure of the RCF remained largely unchanged compared to the original carbon fibers. Surface oxidation occurred during the recycling process, leading to an increase in O–C=O content on the surface of the RCF compared to that of the VCF, which facilitated interfacial chemical bonding with the resin and enhanced the wettability. Compared to virgin carbon fiber-reinforced plastics (VCFRP), RCFRP retained up to 95.25% of the tensile strength, 97.47% of the shear strength, and 96.76% of the bending stress, demonstrating excellent mechanical properties. This study provides a simple and effective approach for the low-temperature and high-efficiency recycling of carbon fiber composites. Full article

This review explores the evolving landscape of sustainable textile manufacturing, with a focus on rubber-based materials for various industrial applications. The textile and rubber industries are shifting towards eco-friendly practices, driven by environmental concerns and the need to reduce carbon footprints. The integration of sustainable textiles in rubber-based products, such as tires, conveyor belts, and defense products, is becoming increasingly prominent. This review discusses the adoption of natural fibers like flax, jute, and hemp, which offer biodegradability and improved mechanical properties. Additionally, it highlights sustainable elastomer sources, including natural rubber from Hevea brasiliensis and alternative plants like Guayule and Russian dandelion, as well as bio-based synthetic rubbers derived from terpenes and biomass. The review also covers sustainable additives, such as silica fillers, nanoclay, and bio-based plasticizers, which enhance performance while reducing environmental impact. Textile–rubber composites offer a cost-effective alternative to traditional fiber-reinforced polymers when high flexibility and impact resistance are needed. Rubber matrices enhance fatigue life under cyclic loading, and sustainable textiles like jute can reduce environmental impact. The manufacturing process involves rubber preparation, composite assembly, consolidation/curing, and post-processing, with precise control over temperature and pressure during curing being critical. These composites are versatile and robust, finding applications in tires, conveyor belts, insulation, and more. The review also highlights the advantages of textile–rubber composites, innovative recycling and upcycling initiatives, addressing current challenges and outlining future perspectives for achieving a circular economy in the textile and rubber sectors. Full article

This research utilized recycled acetate fibers from discarded cigarette butts (CBs) as reinforcing materials, reducing solid waste and enhancing the properties of bitumen. The surface properties of the fibers significantly impacted the binder characteristics. The treatment of CB fibers with anhydrous ethanol was employed to remove the plasticizer glycerol triacetate (GTA), enabling the better homogeneity of the fibers in the binder. Thermogravimetric analysis (TGA) and scanning electron microscopy (SEM) were used to assess the effectiveness of the fiber treatment. A dynamic shear rheometer (DSR) was used to explore the properties of bitumen with varying CB contents (0%, 0.25%, 0.75%, and 1.25% by weight). A whole life cycle analysis further confirmed the eco-efficiency of CB binders. The results show that the pretreatment effectively removed GTA, leading to a more homogeneous dispersion of fibers in the binder. Adding CBs can significantly improve bitumen properties, but this effect does not increase with higher dosages; when the CB content exceeded 1.25%, a reduction in fatigue resistance was observed. Among the tested dosages, the optimal amount was 0.75%, which improved the high-temperature performance of the binder by 2.7 times, the medium-temperature fatigue life by 1.78 times, and the low-temperature performance by 1.08 times. In terms of ecological benefits, the addition of CB fibers to bitumen pavement reduced carbon emissions by two-thirds compared to traditional bitumen pavement, resulting in a significant decrease in carbon emissions. This study provides valuable insights into the construction of sustainable transportation infrastructure. Full article

The increasing demand for fully recyclable composites has spurred extensive research on thermoplastics, valued for their recyclability and excellent mechanical properties. High-performance thermoplastics such as PEEK and PPS have been widely adopted in aerospace applications due to their outstanding load-bearing capabilities, which are well documented. Recently, thermoplastic polymer blends have gained attention for their enhanced recyclability and sustainability, as well as their ability to improve thermal stability, viscosity, and manufacturability. However, limited data are available on the mechanical characterization of composites that incorporate these blends, particularly when recycled thermoplastics are used. In this study, we first examine the stress–strain behavior of the following three polymer blends relevant for structural applications: PES/PEEK, PPS/PEEK, and HDPE/PP. We then perform a numerical analysis to predict the mechanical performance of unidirectional fiber-reinforced composites using each blend as the matrix. This involves a micromechanical Representative Volume Element (RVE) approach combined with an advanced polymer model previously validated against experimental data. The findings are discussed to critically assess the suitability of these blends for producing fully matrix-recycled composites. Full article

The recycling of waste materials that are usually expensive to dispose of, such as carbon fiber reinforced plastic (CFRP) dust and ferrous dust or sludge, can open up interesting economic prospects and free up landfill space. The agglomeration process is used to combine these two types of waste and produce an aggregate that can be used in shaft furnaces. The carbon contained in the CFRP dust serves as a potential reducing agent in metallurgical processes. The report shows the technical parameters of the wet agglomeration with subsequent sintering for the production of the pellets and provides evidence of the material recycling of the carbon fiber waste. A comparison with primary pellets shows the suitability. Full article

The generation of pyrolysis liquids and gases with poor quality is a limiting factor for the development of the recycling process of fiber-reinforced plastic waste. In this article, the life cycle assessment (LCA) of an advanced two-step pyrolysis process to recycle glass fiber-reinforced polyamide waste is presented. First, the solid waste is pyrolyzed by heating up at 3 °C/min to 500 °C in a tank reactor. The generated volatiles are subsequently thermally cracked at 900 °C in a tubular packed bed reactor. The process is able to reclaim the glass fibers similarly to the conventional one reactor pyrolysis, while producing liquids and gases with better properties. The large quantity of oxygenated pyrolysis oils generated in the conventional pyrolysis are cracked into gaseous hydrocarbons, CO, CO₂ and a minor aqueous liquid. The pyrolysis gases become the main product of the process, presenting an interesting composition of hydrogen (39.9 vol.%), methane (22.5 vol.%), carbon monoxide (19.5 vol.%) and ethylene (10.8 vol.%). The LCA shows that advanced pyrolysis demonstrates better environmental performance than conventional pyrolysis, avoiding fossil resource scarcity and reducing global warming by half and human carcinogenic toxicity by one third. Full article

The increasing demand for sustainable materials in automotive applications, coupled with the critical need to address marine plastic pollution, presents an opportunity for innovative material development. This study explores composites made from recycled polyamide 6 (PA6) fishing nets reinforced with switchgrass fibers (0–30 wt%). The composite with 30 wt% switchgrass fibers increased tensile strength by 23% and Young’s modulus by 126% compared to unreinforced recycled PA6, achieving 93% of the tensile strength of commercial automotive-grade neat PA6 and surpassing another grade by 22%. However, higher fiber loading hindered processability, as evidenced by incomplete mold filling and reflected by a decrease in melt flow rate from 19.35 to 8.63 g/10 min. Thermal analysis revealed reduced crystallinity and crystallization temperatures with fiber addition, attributed to restricted polymer chain mobility. While dynamic mechanical analysis demonstrated improved stiffness below the glass transition temperature, scanning electron microscopy indicated optimal fiber-matrix adhesion at up to 20 wt% fiber loading, with aggregation at higher concentrations. These findings establish recycled fishing net-derived PA6/switchgrass fiber composites as a viable alternative to virgin materials in automotive applications, with mechanical properties comparable to commercial grades. Although the composites demonstrate enhanced mechanical strength and modulus, the significant reduction in ductility restricts their use to rigid, semi-structural components where flexibility is not critical. Future research should address processing challenges to enhance fiber dispersion and interfacial adhesion at higher loadings. Full article