Search Results (86)

This paper presents the design of a batteryless near-field communication (NFC) multi-sensor node with an integrated adaptive power-management system for sensing applications. The work focuses on harvesting energy from a 13.56 MHz NFC field to power an ultra-low power sensing platform. The design consists of the TI RF430FRL152H, an integrated NFC transponder with an embedded MSP430 microcontroller core and ferroelectric random-access memory (FRAM) non-volatile memory. The system combines an ISO/IEC 15693 NFC front end, a tuned loop antenna for optimized power harvesting, and multiple analog and digital sensor interfaces, and a firmware architecture for intermittent harvested energy operation. The aforementioned design performs on-demand data acquisition, logs measurements in the FRAM, and communicates the measured results through an ISO15693 compliant NFC link while powered entirely by the reader’s radio-frequency (RF) field. Since NFC provides only limited harvested power, efficient energy management is critical. The proposed scheme continuously monitors the storage capacitor voltage and activates each sensor only when sufficient energy is available. After every measurement, the system reassesses the stored charge before triggering the next acquisition, ensuring stable multi-sensor operation. A BMP390 temperature and pressure sensor and the on-chip temperature sensor demonstrate the platform’s capability. Experimental results show that the system harvests 1.064 mW (1.85 V, 560 µA), achieves a wireless operating range of up to 40 mm, and delivers a response time of 800 ms, demonstrating its suitability for low-power temperature and pressure sensing applications. Full article

Radio frequency identification (RFID) technology has been widely adopted in a variety of practical applications. Usually, the size of a passive tag antenna largely determines the read performance of tag. However, excessively large tag antennas can hinder their practical application and a tag that is too small has poor performance. In this paper, a compact, flexible and corrosion-resistant folding dipole tag antenna is proposed, which has a geometrical dimension of 24 mm × 13 mm (0.074${\mathsf{\lambda }}_0\times 0.040{\mathsf{\lambda }}_0$). It is designed on only one surface of a flexible polyethylene terephthalate (PET) substrate, which can be folded. The paper proposes a single-sided laser-patterned GAF/PET flexible RFID tag that is mechanically folded to form a backside dipole arm without vias, targeting compact and corrosion-resistant UHF RFID operation. Changing the size of the folding arm can effectively adjust the resonant frequency and impedance of the tag antenna. A stepped radiation arm is used to extend the current path and lower the resonance frequency. The capacitance and inductance effects introduced by loading a T match for reducing the resonant frequency of the tag to the useful UHF RFID band. Finally, it can achieve a power transfer coefficient of 99.9% and exhibit high impedance matching between the tag antenna and the chip. The proposed tag antenna uses graphene-assembled film (GAF) as its conductor material. Thanks to the physicochemical properties of GAF, the proposed tag antenna maintains stable radiation performance even after prolonged exposure to acidic (5 wt%), alkaline (5 wt%), and salt (5 wt%) corrosion, as well as more than 1000 mechanical bending cycles. When the EIRP of the reader is 2.2 W, the maximum read range of the tag in the 800–1000 MHz is 1.38 m. Full article

In grain storage and transportation, biological activity, including respiration and metabolism, generates heat, creating temperature gradients that can induce moisture migration and form high-humidity areas. This accelerates fungal and insect activity, leading to quality degradation. Long-term, distributed temperature monitoring inside grain piles is essential for ensuring safe storage and early risk warning. Radio Frequency Identification (RFID) technology has become widely adopted in storage temperature monitoring due to its low cost, maintenance-free operation, and high security. However, traditional RFID systems have limited communication ranges, and the large size of storage facilities necessitates the deployment of multiple readers, which increases costs. Additionally, the high density and fluctuating moisture content of bulk grain lead to significant RF signal absorption and scattering, weakening the accessibility of purely wireless systems to deeper parts of the grain pile. To address these issues, a passive distributed temperature monitoring system based on RFID technology is proposed. The system utilizes RFID readers to harvest RF energy for passive power supply, with an external antenna ensuring stable energy harvesting and data transmission. Single-bus multi-point temperature sensor modules are integrated into the system, enabling distributed temperature measurements across grain piles or warehouses. Experimental results show that the system achieves a temperature collection success rate of 98%, with an accuracy of ±1 °C and a polling cycle of less than 30 s, providing a low-cost, battery-free, and scalable solution for grain storage monitoring, significantly improving storage quality. Full article

Many authors analyze the chaotic motion of the driven and damped double sine-Gordon equations and compute the Melnikov functions by numerical methods, taking an example to verify good agreement between numerical methods and analytical ones. Unfortunately, due to the lack of an explicit presentation of the Melnikov integral, the reader has difficulty navigating and touching upon Melnikov’s elegant theory and, in particular, the formulation of the Melnikov criterion for the occurrence of chaos in a dynamical system, based solely on the provided illustrations of dependencies between the main parameters of the model under consideration. In this paper we will try to shed additional light on this important problem. A new planar system corresponding to the generalized double sine-Gordon model with many free parameters is considered. We also look at the modeling of radiation diagrams and antenna factors as potential uses for the Melnikov functions. A number of simulations are created. We also show off a few specific modules for examining the model’s behavior. There is also discussion of one use for potential oscillation control. Full article

This paper presents a fully passive and wireless glucose concentration sensor that integrates a capacitively coupled complementary split-ring resonator (CSRR) with an H-slot UHF RFID antenna. The CSRR serves as the primary sensing element, where changes in glucose concentration alter the effective permittivity of the surrounding solution, thereby modifying the resonator capacitance and shifting its resonance behavior. Through near-field capacitive coupling, these dielectric variations affect the antenna input impedance and backscatter response, enabling wireless sensing by modulating the maximum read range. The proposed sensor operates within the 902–928 MHz UHF RFID band and is interrogated using commercial RFID readers, eliminating the need for specialized laboratory equipment such as vector network analyzers. Full-wave electromagnetic simulations and experimental measurements validate the sensor performance, demonstrating a variation in the read range from 6.23 m to 4.67 m as glucose concentration increases from 50 to 200 mg/dL. Moreover, the sensor exhibits excellent linearity, with a high coefficient of determination ($R^2=0.986$) based on the curve-fitted data. These results underscore the feasibility of the proposed sensor as a low-cost and fully portable platform for concentration monitoring, with potential applications in liquid characterization and chemical sensing. Full article

This paper presents the design of a circularly polarized RFID ground mat antenna for UHF-band sports-event applications. Considering a practical sports-event timing system, the ground-based mat antenna with characteristics of a low-backward radiation and circular polarization is proposed. A multilayer square patch antenna using an acrylic dielectric substrate with a wideband branch-line coupler feeding network is employed to improve overall radiation efficiency, which, in turn, provides two excitation port with a phase difference of 90°. Thus, right-hand circular polarization can be obtained. Instead of a conventional FR4–air–FR4 structure, the proposed FR4–acrylic–FR4 composite configuration is adopted to substantially increase the antenna’s mechanical strength and durability against external pressure from runners. The antenna’s performance is attributed to the use of an effective composite dielectric constant and an optimized design of its parameters. Additionally, the patch antenna’s low-backward radiation characteristic helps reduce multipath interference in real-world applications. The measured results are in good agreement with the simulated data, validating the proposed antenna design. In order to further assess the practical performance of the antenna, outdoor measurements are carried out to validate the estimated reading distances derived from controlled anechoic chamber tests. The measured return loss remained below −10 dB across the frequency range of 755–990 MHz, exhibiting a slight discrepancy compared to the simulated bandwidth of 800–1030 MHz. For the characteristic of the circular polarization, the measured axial ratio is below 3 dB within the range of 860–920 MHz. While a more relaxed criterion of an axial ratio below 6 dB is considered, the operating frequency range extends from 560 MHz to 985 MHz, which falls within the frequency band relevant for RFID reader applications. Full article

The last few years have seen the introduction of new technologies in beekeeping, including RFID. Using readers and miniaturized tags, RFID systems work in the UHF frequency band, allowing reading distances to reach tens of centimeters. This work analyzes the propagation inside a full beehive, composed of 10 frames supported by a wooden structure. Each frame contains a layer of beeswax supported by metallic wires. The methodology employed involves measuring Received Signal Strength Indicator (RSSI) values and simulating the environment using CST Studio. The results show that tags located along the frame’s wires have more coverage than tags in the center positions, revealing coupling of the microtag antenna with the wire. Furthermore, obtaining coverage through simulations represents a more restrictive approach than through measurements. Frame selectivity is also observed, as most of the coverage is found within the three frames closest to the reader antenna. This result shows that RFID systems can find application in the identification and location of the queen bee in a hive. Full article

High-voltage direct-current (HVdc) transmission lines are gaining more attention as an integral part of modern power system networks. Monitoring the dc current is important for metering and the development of dynamic line rating control schemes. However, this has been a challenging task, and there is a need for wireless sensing methods with high accuracy and a dynamic range. Conventional methods require direct contact with the high-voltage conductors and utilize bulky and complex equipment. In this paper, an ultra-high-frequency (UHF) radio frequency identification (RFID)-based sensor is introduced for the monitoring of the dc current of an HVdc transmission line. The sensor is composed of a passive RFID tag with a custom-designed antenna, integrated with a Hall effect magnetic field device and an RF power harvesting unit. The dc current is measured by monitoring the dc magnetic field around the conductor using the Hall effect device. The internal memory of the RFID tag is encoded with the magnetic field data. The entire RFID sensor can be wirelessly powered and interrogated using a conventional RFID reader. The advantage of this approach is that the sensor does not require batteries and does not need additional maintenance during its lifetime. This is an important feature in a high-voltage environment where any maintenance requires either an outage or special equipment. In this paper, the detailed design of the RFID sensor is presented, including the antenna design and measurements for both the RFID tag and the RF harvesting section, the microcontroller interfacing design and testing, the magnetic field sensor calibration, and the RF power harvesting section. The UHF RFID-based magnetic field sensor was fabricated and tested using a laboratory experimental setup. In the experiment, a 40 mm-diameter-aluminum conductor, typically used in 500 kV HVdc transmission lines carrying a dc current of up to 1200 A, was used to conduct dc current tests for the fabricated sensor. The sensor was placed near the conductor such that the Hall effect device was close to the surface of the conductor, and readings were acquired by the RFID reader. The sensitivity of the entire RFID sensor was 30 mV/mT, with linear behavior over a magnetic flux density range from 0 mT to $4.5$ mT. Full article

This paper proposes a standard applications of Radio Frequency Identification (RFID) system to manage vehicles at electronic toll gate system without compromising the vehicle speed. The existing electronic toll gate system has low latency as each car needs to wait in a queue for passing the gate. Installation of reader antenna at each lane makes the system expensive. We propose a two-ray ground model for using minimal reader antenna to define required antenna height and downtilt angle to cover the total gate area. We estimate that reader antenna at a height of 15 m and 45.4° downtilit angle are required for optimal signal reception from the car at a distance of 35–38 m. Modified Pulse Protocol algorithm is suggested for mitigating reader collision and increase throughput and utilization of the system by 14.71% and 15.2% respectively. The probability distribution function of the contention window is modified to triangular function. The M-ary Trimming Q-tree protocol is suggested to resolve the tag collision by trimming the idle nodes from the query tree, which reduces identification time. The total time slot decreases with higher elements, and the total throughput also increases to 98%. The “no-lane” strategy established a fast, efficient and cost effective vehicle toll collection system. Full article

Two-dimensional leaky-wave antennas offer effective, compact, single-feeder, easy-to-fabricate solutions to the longstanding problem of realizing a simultaneously directive and low-profile radiating device. These traveling-wave antennas have been thus proposed as wideband, reconfigurable, or frequency-scanning radiating structures in different application contexts, spacing from the microwave to terahertz frequency range. These diverse contexts call for a comprehensive guide to characterizing and designing two-dimensional leaky-wave antennas. In this work, a review of numerical techniques for the analysis of either quasi-uniform or radially periodic leaky-wave antennas is proposed in order to provide the reader with straightforward yet effective design guidelines. Theoretical results are corroborated through full-wave simulations of realistic three-dimensional models of the considered devices, thus demonstrating the effectiveness of the proposed methods. Full article

Resonators are passive devices that respond to an excitation signal by oscillating at their natural frequency with exponentially decreasing amplitudes. Physical, chemical and electrical variables can modify the natural frequencies of resonators. If resonators are connected to antennas or other transducers that couple into a communication channel, they enable purely passive sensors that can be read wirelessly. In this manuscript, we use maximum likelihood estimation to analyze the measurement accuracy that can be achieved by the wireless readout of passive resonant sensors as a function of the read signal, the stimulation power and noise figure of the reader, the distance and transducer gain of the transmission channel, and the natural frequency and quality factor of the resonant passive sensor. The Crámer–Rao lower bound characterizes the minimum variance of the natural frequency and decay constant of the resonator. We show the derivation of the Crámer–Rao lower bounds from the Fisher information matrix based on a maximum likelihood estimation of discrete-time samples of an exponentially decaying phasor. This theoretical lower limit of accuracy is almost achieved by an iterative algorithm that approximates the maximum of the measured resonator spectrum with a Lorentz curve. Full article

In radio frequency identification (RFID), differences in spectrum policies and tag misreading in different countries are the two main issues that limit its application. To solve these problems, this article proposes a composite right/left-handed transmission line (CRLH-TL)-based reconfigurable antenna for ultra-high frequency near-field and far-field RFID reader applications. The CRLH-TL is achieved using a periodically capacitive gap-loaded parallel plate line. By deploying the CRLH-TL operating at zeroth-order resonance, a loop antenna with in-phase radiating current is obtained, which contributes to a strong and uniform H-field and a horizontally polarized omnidirectional radiation pattern. By introducing additional tunable components, frequency and reading range reconfigurabilities are enabled. The frequency tuning range is from 833 MHz to 979 MHz, which covers the worldwide UHF RFID band. Moreover, each operation mode has a narrow frequency band, which means it can operate without violating different countries’ radio frequency policy and reduce the design difficulty of designing multiple versions of a reader. Both the near-field interrogation zone and maximum far-field reading distance of the antenna are adjustable. The near-field interrogation zone is 400 mm × 400 mm × 50 mm and can be further confined. The tuning range for far-field reading distance is from 2.71 m to 0.35 m. Full article

Azimuth resolution and swath width are two crucial parameters in spaceborne synthetic aperture radar (SAR) systems. However, it is difficult for conventional spaceborne SAR to simultaneously achieve high-resolution wide-swath (HRWS) due to the minimum antenna area constraint. To mitigate this limitation, some representative HRWS SAR imaging techniques have been investigated, e.g., the azimuth multichannel technique, digital beamforming (DBF) technique, and pulse repetition interval (PRI) variation technique. This paper focus on a comprehensive review of the three techniques with respect to their latest developments. First, some key parameters of HRWS SAR are presented and analyzed to help the reader establish the general concept of SAR. Second, three techniques are introduced in detail, roughly following a simple-to-complex approach, i.e., start with the basic concept, then move to the core principles and classic technical details, and finally report the technical challenges and corresponding solutions. Third, some in-depth insights on the comparison among the three techniques are given. The purpose of this paper is to provide a review and brief perspective on the development of HRWS SAR. Full article

RFID (Radio Frequency Identification), which transmits control data through electronic tags in a non-contact manner, provides a new approach for efficient and low-cost remote control of oil downhole tools. However, the interference of harsh downhole environments and the high-speed movement of tags seriously affect the performance of the current downhole reader. To effectively address this issue, in this study, a novel downhole RFID reader is presented. By introducing the half-duplex communication protocol to replace the current full-duplex communication protocol in the hardware circuits of the reader, its tag recognition ability can be improved. Then, the corresponding hardware circuits and software programs are designed. Furthermore, a sparse solenoid antenna is adopted to replace the traditional tightly wound solenoid antenna, which can provide a longer reading area range to cope with the high-moving tag, and its total length and spacing parameters between adjacent coils are designed in detail. The test results show that the proposed RFID reader based on a half-duplex communication protocol can communicate with tags normally, and its sparse solenoid antenna provides significantly more tag reading times than traditional tightly wound solenoid antennas under the same antenna inductance. Full article

Although RFID(radio frequency identification) tags do not require a direct line of sight, their operational range is often characterized as being limited. Indeed, in the case of passive RFID tags, the interrogating signal from the transmitter needs to reach the tag’s radio transponder and trigger a nearly omnidirectional scattered signal to be harvested by the receiver. This two-way (from Tx to the tag and back to Rx) channel exhibits increased attenuation not only due to the doubled distance (in case Tx and Rx are collocated) but also to the uncontrolled (i.e., unfocused) backscattering. In the work at hand, we propose a way to control the backscattered radiation and focus the produced beam towards the direction of the reader (the Tx-Rx device). Indeed, one can utilize the concept of retrodirective arrays to immediately control the direction of departure of the backscatter link, maximizing the scattered power towards the reader and thus delivering an increase in the operational range of the tag. This of course means that in this case, the tag should be equipped with a minimum of two element radiators. Thus, retrodirective RFID array tags are introduced in the current work to increase the operating range with minimal costs and levels of complexity since 90° hybrids are used to achieve proper backscattering. To evaluate the proposed passive tag array, performance aspects are addressed. Specifically, we examine the Bit Error Rate with respect to the Signal to Noise Ratio for the retrodirective tag, the one antenna, the broadside, and the spatial diversity array. The results prove that the proposed tag allows for a significant increase in the operational range. Full article