Search Results (32)

Stimuli-sensitive (in situ) drug delivery systems are a dynamically developing area of pharmaceutical research. Over the past decade, the number of studies on such systems has doubled. Among these, phase-inversion (or phase-sensitive) formulations, which were among the earliest proposed, offer significant advantages, including enhanced stability and stimuli-responsiveness. However, phase-inversion systems have remained relatively understudied. Despite the existence of three patented technologies (Atrigel^®, BEPO^®, FluidCrystal^®) for delivery systems utilizing phase inversion for various routes of administration, the absence of unified approaches to development and standardization has significantly impeded the introduction of novel, effective drugs into clinical practice. This review examined the main polymers and solvents used to create phase-inversion compositions and discussed the feasibility of introducing other excipients to modify the systems’ physicochemical properties. The most commonly used polymers included polylactide-co-glycolide, shellac, and polylactic acid. The most frequently used solvents were N-methylpyrrolidone and dimethyl sulfoxide. Following an analysis of clinical studies of phase-sensitive drugs conducted over the past 25 years, as well as original research indexed in PubMed, ScienceDirect, and Google Scholar, the main problems hindering the broader adoption of phase-inversion systems in clinical practice were identified, and recommendations for further development in this promising area were provided. Full article

A deep learning strategy was exploited to learn and predict the deformation of stiffeners, 3D printed onto a pre-stretched soft membrane. The working process reads as follows: the membrane is stretched until a pre-defined level; a specific geometry of stiffeners is printed onto it; the membrane is finally released, and due to the presence of the printed stiffeners, the system undergoes an out-of-plane deformation due to buckling. Fused deposition modeling was specifically calibrated to print PLA (Polylactic acid or polylactide) on a Lycra fabric. To assess how the printed pattern affects the buckled configuration, samples featuring different dimensions and in-plane geometries of the stiffeners were printed and numerically modeled via finite elements (FEs). The calibrated model was next exploited to construct a larger training dataset of stiffener geometries. A pre-trained You Only Look Once (YOLO)-based digital model was finally trained to foresee the link between the in-plane dimensions of the stiffeners before the release and the out-of-plane displacements in the buckled configuration. By handling around 100 different patterns, a precision of 93% in terms of recognition of the in-plane dimensions of the stiffeners and a mean absolute percentage error of 5% at most in terms of an estimate of the features of the buckled configuration were attained. The reported results testify the capability of the proposed approach and its potential efficiency to optimize the shape of the 3D printed geometries. Full article

The aim of the work is to study the effect of the 3D printing process on the microstructural and hydrophilic properties of polylactic acid (PLA) samples with various model printing patterns obtained from the black filament PLA by sequentially applying polymer layers using the FDM (fused deposition modeling) method. X-ray phase analysis revealed the partial crystallization of PLA polymer chains in the printed samples, which occurs under thermal and mechanical action on the original amorphous PLA filament during 3D printing to varying degrees, depending on the geometry of the pattern and the morphology of its surface. At the same time, IR spectroscopy data indicate the preservation of all intrastructural chemical bonds of polylactide. Measured at the original installation, the values of the wetting edge angles on the surface of the printed samples are in the range φ = 50–60°, which is significantly less than the right angle. This indicates the hydrophilic properties of the whole sample’s surface. At the same time, the influence of different geometries of model drawings in printed samples was found not only on the morphology of the sample’s surface according to SEM data but also on its wettability. Full article

This study investigated the successful synthesis and characterization of nonisocyanate polyurethanes (NIPUs) based on polylactide. The NIPUs were synthesized by a condensation reaction of oligomers with hard segments (HSs) and synthesized carbamate-modified polylactic acid containing flexible segments (FSs). The oligomers with HSs were prepared from phenolsulfonic acid (PSA) or a mixture of PSA and hydroxynaphthalenesulfonic acid (HNSA), urea and formaldehyde. The mixing of oligomeric compounds with different amounts of formaldehyde was carried out at room temperature. Obtained NIPU samples with different hard segment content were tested for their mechanical and thermal properties. The tensile strength (TS) of all NIPU samples increased with an increasing amount of HSs, attaining the maximum value at an HS:FS ratio of 1:3. Samples prepared from PSA and HNSA showed higher tensile strength (TS) without significant change in elongation at break compared to the samples based only on PSA. Thermogravimetric analysis data indicated an absence of weight loss for all samples below 100 °C, which can be considered a safe temperature for using NIPU materials. Maximum degradation temperatures reached up to 385 °C. Fourier transform infrared spectroscopy results confirmed the existence of expected specific groups as well as the chemical structure of the prepared polyurethanes. DSC analysis showed the existence of two characteristic phase transitions attributed to the melting and crystallization of hard segments in the NIPU samples. Full article

In the modern world, many products are disposable or have a very short lifespan, while at the same time, those products are made from materials that will remain in the environment in the form of waste for hundreds or even thousands of years. It is a serious problem; non-biodegradable polymer wastes are part of environmental pollution and generate microplastics, which accumulate in the organisms of living beings. One of the proposed solutions is biodegradable polymers and their composites. In our work, three types of polylactide-based composites with plant-derived fillers: microcellulose powder, short flax fibers, and wood flour at 2 wt.% were prepared. Poly(lactic acid) (PLA)-based biocomposite properties were characterized in terms of mechanical and surface properties together with microscopic analysis and Fourier-transform infrared spectroscopy (FTIR), before and after a UV (ultraviolet)-light-aging process to determine the effects of each cellulose-based additive on the UV-induced degradation process. This research shows that the addition of a cellulose additive can improve the properties of the material in terms of the UV-aging process, but the form of the chosen cellulose form plays a crucial role in this case. The testing of physicochemical properties demonstrated that not only can mechanical properties be improved, but also the time of degradation under UV light exposure can be controlled by the proper selection of the reinforcing phase and the parameters of the extrusion and injection molding process. The obtained results turned out to be very interesting, not only in terms of the cost reduction of the biocomposites themselves, as mainly the waste from the wood industry was used as a low-cost filler, but also that the additive delays the aging process occurring during UV light exposure. Even a small, 2 wt.% addition of some of the tested forms of cellulose delayed surface degradation, which is one of the most important factors affecting the biodegradation process. Full article

Biocomposites based on polylactic acid (PLA), tall wheatgrass (TWG), and hemp (H) were made by injection molding. The article discusses the impact of the agrofiller content on the composite properties, including thermal (DSC, DMA, and TG) and mechanical characteristics (tensile modulus, tensile strength, and impact strength). Generally, the introduction of a plant filler into the polylactide matrix reduced the thermal resistance of the resulting composites. Plant fillers influenced primarily the cold crystallization process, probably due to their nucleating properties. The addition of fillers to the PLA matrix resulted in an increased storage modulus across all tested temperatures compared to pure PLA. In the case of a composite with 50% of plant fillers, it was almost 118%. The mechanical properties of the tested composites depended significantly on the amount of plant filler used. It was observed that adding 50% of plant filler to PLA led to a twofold increase in tensile modulus and a decrease in tensile strength and impact strength by an average of 23 and 70%, respectively. It was determined that composites incorporating tall wheatgrass (TWG) particles exhibited a slightly elevated tensile modulus while showcasing a marginally reduced strength and impact resistance in comparison to composites containing hemp (H) components. Full article

Given the global challenge of plastic pollution, the development of new bioplastics to replace conventional polymers has become a priority. It is therefore essential to achieve a balance in the performances of biopolymers in order to improve their commercial availability. In this topic, this study aims to investigate the morphology and properties of poly(lactic acid) (PLA)/ poly(3-hydroxybutyrate-co-3-hydroxyhexanoate) (PHBHHx) (at a ratio of 75/25 (w/w)) blends reinforced with halloysite nanotubes (HNTs) and compatibilized with poly(lactic acid)-grafted maleic anhydride (PLA-g-MA). HNTs and PLA-g-MA were added to the polymer blend at 5 and 10 wt.%, respectively, and everything was processed via melt compounding. A scanning electron microscopy (SEM) analysis shows that HNTs are preferentially localized in PHBHHx nodules rather than in the PLA matrix due to its higher wettability. When HNTs are combined with PLA-g-MA, a finer and a more homogeneous morphology is observed, resulting in a reduction in the size of PHBHHx nodules. The presence of HNTs in the polymer blend improves the impact strength from 12.7 to 20.9 kJ/mm². Further, with the addition of PLA-g-MA to PLA/PHBHHX/HNT nanocomposites, the tensile strength, elongation at break, and impact strength all improve significantly, rising from roughly 42 MPa, 14.5%, and 20.9 kJ/mm² to nearly 46 MPa, 18.2%, and 31.2 kJ/mm², respectively. This is consistent with the data obtained via dynamic mechanical analysis (DMA). The thermal stability of the compatibilized blend reinforced with HNTs is also improved compared to the non-compatibilized one. Overall, this study highlights the effectiveness of combining HNTs and PLA-g-AM for the properties enhancement of PLA/PHBHHx blends. Full article

Wood–plastic composites (WPCs) represent composite materials that employ shredded wood combined with a thermoplastic substance, such as polylactic acid (PLA), to establish structural cohesion within the product profile. This amalgamation of materials results in a robust structure designed to fulfill specialized roles under the influence of pressure and temperature. Given the nature of the constituent materials, the resultant product can be classified as a biocomposite. The creation of such biocomposites entails a rigorous process necessitating the fine-tuning of specific parameters and suitable technologies. The foundational materials employed in this process must be both natural and biodegradable. However, it is noteworthy that natural components like fibers exhibit anisotropic behavior, wherein their mechanical attributes are contingent on the direction of the applied force. Consequently, predicting their performance during biocomposite production proves challenging. The principal objective of this study was to conduct a comparative analysis of wood-based composites incorporating PLA thermoplastic binding agents. The intention was to discern variations in density profiles arising from distinct measurement methodologies. Two measurement methods were used for the measurement: X-ray and spectrum desaturation. Additionally, the study sought to investigate the impact of introducing PLA additives at 25% and 50% concentrations on the fabrication of WPC from wood chips. The properties of these composites were assessed by considering the inherent traits of the composite materials. Full article

In this work, the feasibility of applying a digital twin combined with machine learning algorithms (convolutional neural network and random forest classifier) to predict the performance of PLA (polylactic acid or polylactide) parts is being investigated. These parts are printed using a low-cost desktop 3D printer based on the principle of fused filament fabrication. A digital twin of the extruder assembly has been created in this work. This is the component responsible for melting the thermoplastic material and depositing it on the print bed. The extruder assembly digital twin has been separated into three simulations, i.e., conjugate convective heat transfer, multiphase material melting, and non-Newtonian microchannel. The functionality of the physical extruder is controlled by a PID/PWM circuit, which has also been modelled within the digital twin to control the virtual extruder’s operation. The digital twin simulations were validated through experimentation and showed a good agreement. After validation, a variety of parts were printed using PLA at four different extrusion temperatures (180 °C, 190 °C, 200 °C, 210 °C) and ten different extrusion rates (ranging from 70% to 160%). Measurements of the surface roughness, hardness, and tensile strength of the printed parts were recorded. To predict the performance of the printed parts using the digital twin, a correlation was established between the temperature profile of the non-Newtonian microchannel simulation and the experimental results using the machine learning algorithms. To achieve this objective, a reduced order model (ROM) of the extruder assembly digital twin was developed to generate a training database. The database generated by the ROM (simulation results) was used as the input for the machine learning algorithms and experimental data were used as target values (classified into three categories) to establish the correlation between the digital twin output and performance of the physically printed parts. The results show that the random forest classifier has a higher accuracy compared to the convolutional neural network in categorising the printed parts based on the numerical simulations and experimental data. Full article

The importance of promising composites in modern materials science is constantly increasing. The use of various fillers or additives is associated with their influence not only on the defining properties of the composite, but also on physical and mechanical characteristics of the material. In this case, the distribution of the additive and its wetting with a polymer play an important role. The problem highlighted in this article is the influence of different copper-containing fillers (copper (II) sulphate powder, micro-sized copper (II) oxide powder, and nano-structured copper (II) oxide-based hollow microspheres) on the technological and physical–mechanical properties of the composites based on polylactic acid (PLA). The hollow microspheres of copper (II) oxide have been obtained by ultrasonic spray atomization via pyrolysis of copper (II) nitrate. The structure of the copper-based additives has been studied using X-ray diffraction, scanning electron microscopy, and static light scattering. For the PLA-composites, scanning electron microscopy, differential scanning calorimetry, stress-strain properties testing, and density analysis have been performed. The plasticizing effect of polycaprolactone and polyethylene glycol has been studied for the highly filled PLA/CuSO₄ composite. The samples of PLA with over 2 wt.% of CuO microspheres have a full volume-filling and percolation structure of the additive’s particles. Due to the regular spherical shape of the particles and a lower specific volume, CuO hollow microspheres are uniformly distributed in the PLA matrix acting as a structuring and reinforcing modifier. Differential scanning analysis showed heterogeneous crystallization on CuO particles with an increase in the degree of crystallinity and the melting point of the polymer. It has been shown that the pre-masterbatching technology and adding plasticizers to obtain PLA composites contribute minimizing defects and enhance mechanical properties. Full article

The development of functional materials from food waste sources and minerals is currently of high importance. In the present work, polylactic acid (PLA)/silica composites were prepared by in situ ring-opening polymerizations of L-lactide onto the surface of pristine (Silochrom) and amine-functionalized (Silochrom-NH₂) silica. The characteristics of the ring-opening polymerization onto the surface of modified and unmodified silica were identified and discussed. Fourier transform infrared spectroscopy was used to confirm the polymerization of lactide onto the silica surface, and thermogravimetric analysis determined that PLA constituted 5.9% and 7.5% of the composite mass for Silochrom/PLA and Silochrom-NH₂/PLA, respectively. The sorption properties of the composites with respect to Pb(II), Co(II), and Cu(II) ions were investigated, and the effect of contact time, initial metal ion concentration, and initial pH were evaluated. Silochrom-NH₂/PLA composites were found to have a higher adsorption capacity than Silochrom/PLA for all chosen ions, with the highest adsorption value occurring for Pb²⁺ at 1.5 mmol/g (90% removal efficiency). The composites showed the highest performance in the neutral or near-neutral pH (created by distilled water or buffer pH 6.86) during the first 15 min of phase contact. The equilibrium characteristics of adsorption were found to follow the Langmuir isotherm model rather than the Freundlich and Temkin models. Perspective applications for these PLA/silicas include remediation of industrial wastewater or leaching solutions from spent lead-acid and Li-ion batteries. Full article

The present paper analyses the properties of printed polylactic acid (PLA) samples with admixtures of graphene nanopowder (GNP) at wt. 1%, 2% and 4%. The pure polylactide and admixed polylactide printed samples were examined to determine their chemical-physical properties, stiffness, and strength parameters. The tests of tensile, dynamic mechanical analysis (DMA), difference thermogravimetric (TG), and differential scanning calorimetry (DSC) were executed before and after UV (ultraviolet) treatment. The first part of the paper shows the process of manufacturing granulates and filaments mixed with graphene. The second part of the paper concerns the results of the tests made on printed samples. The analysed samples were printed using a Prusa i3 MK3 printer. It transpired that the content of graphene at 1% improved the mechanical parameters of the printed composite by organising its structure. Increasing the amount of graphene caused the values of the measured parameters to drop. This research indicates how important it is to determine the optimal values of nanoadditives in biopolymers. Full article

This study provides insight into the accelerated hydrolysis of polyester PLA through the addition of phosphites based on pentaerythritol. To control hydrolysis and ensure processing stability, different types of phosphites and combinations of phosphites with acid scavengers were studied. Therefore, commercially available PLA was compounded with selected additives on a twin-screw extruder, and hydrolysis experiments were performed at 23 °C, 35 °C and 58 °C in deionized water. Hydrolysis of PLA was evaluated by the melt volume rate (MVR) and size-exclusion chromatography (SEC). For example, after 4 days of water storage at 58 °C, the number average molecular weight of the PLA comparison sample was reduced by 31.3%, whereas PLA compounded with 0.8% phosphite P1 had a 57.7% lower molecular weight. The results are in good agreement with the expected and tested stability against hydrolysis of the investigated phosphite structures. ³¹P-NMR spectroscopy was utilized to elucidate the hydrolysis of phosphites in the presence of lactic acid. With the addition of phosphites based on pentaerythritol, the hydrolysis rate can be enhanced, and faster biodegradation behavior of biodegradable polyesters is expected. Accelerated biodegradation is beneficial for reducing the residence time of polymers in composting facilities or during home composting and as litter or microplastic residues. Full article

Drug-loaded microspheres are an ideal bone tissue delivery material. In this study, a biodegradable Schiff base chitosan–polylactide was used as the encapsulation material to prepare drug-loaded microspheres as biocompatible carriers for controlled vancomycin release. In this regard, Schiff base chitosan was prepared by the Schiff base method, and then different proportions of the Schiff base chitosan–polylactide polymer were prepared by ring-opening polymerization. Drug-loaded microspheres were prepared by the W/O emulsion method, and the polymers and polymer microspheres were characterized and studied by NMR, IR, and antibacterial methods. The drug loading and release rates of microspheres were determined to investigate the drug loading, encapsulation efficiency, and release rate of drug microspheres at different ratios. In this study, different proportions of Schiff base chitosan–polylactic acid materials are successfully prepared, and vancomycin-loaded microspheres are successfully prepared using them as carriers. This study proves that the materials have antibacterial activities against Staphylococcus aureus and Escherichia coli. The particle size of drug-loaded microspheres was below 10 μm, and the particle size decreased with decreasing molecular weight. The obtained results show that 1:100 microspheres have the highest drug-loading and encapsulation efficiencies, the drug-loaded microspheres have no burst release within 24 h, and the release quantity reaches more than 20%. After 30 days of release, the release amounts of 1:10, 1:20, 1:40, 1:60, and 1:100 drug-loaded microspheres were 64.80 ± 0.29%, 54.43 ± 0.54%, 44.60 ± 0.43%, 42.53 ± 0.40% and 69.73 ± 0.45%, respectively, and the release amount of 1:100 was the highest. Full article

The aim of this study was to investigate an antimicrobial and degradable composite material consisting of melt-blown poly(lactic acid) nonwoven fabrics, alginate, and zinc. This paper describes the method of preparation and the characterization of the physicochemical and antimicrobial properties of the new fibrous composite material. The procedure consists of fabrication of nonwoven fabric and two steps of dip-coating modification: (1) impregnation of nonwoven samples in the solution of alginic sodium salt and (2) immersion in a solution of zinc (II) chloride. The characterization and analysis of new material included scanning electron microscopy (SEM), specific surface area (SSA), and total/average pore volume (BET). The polylactide/alginate/Zn fibrous composite were subjected to microbial activity tests against colonies of Gram-positive (Staphylococcus aureus), Gram-negative (Escherichia coli) bacterial strains, and the following fungal strains: Aspergillus niger van Tieghem and Chaetomium globosum. These results lay a technical foundation for the development and potential application of new composite as an antibacterial/antifungal material in biomedical areas. Full article