Search Results (326)

Soil testing has long been used to optimize fertilization and crop production. More recently, soil health testing has emerged to reflect the growing interest in soil multifunctionality and ecosystem services. Soil health encompasses physical, chemical, and biological properties that support ecosystem functions and sustainable agriculture. Despite its relevance to several United Nations Sustainable Development Goals (SDGs 1, 2, 3, 6, 12, 13, and 15), comprehensive soil health testing is not widely practiced due to complexity and cost. The aim of the study presented here was to contribute to the further development, implementation, and testing of an integrated procedure for soil health assessment in practice. We developed and tested a rapid, standardized soil health assessment tool that combines near-infrared spectroscopy (NIRS) and multi-nutrient 0.01 M CaCl₂ extraction with Inductive Coupled Plasma Mass Spectroscopy analysis. The tool evaluates a wide range of soil characteristics with high accuracy (R² ≥ 0.88 for most parameters) and has been evaluated across more than 15 countries, including those in Europe, China, New Zealand, and Vietnam. The results are compiled into a soil health indicator report with tailored management advice and a five-level ABCDE score. In a Dutch test set, 6% of soils scored A (optimal), while 2% scored E (degraded). This scalable tool supports land users, agrifood industries, and policymakers in advancing sustainable soil management and evidence-based environmental policy. Full article

The combined effect of non-thermal plasma (NTP) and hydropriming on the germination performance and seedling characteristics of specific varieties of cucumber (Cucumis sativus L.) and broccoli (Brassica oleracea var. italica Plenck.) seeds after short-term storage is reported. Seeds were treated with NTP for 10 and 15 min, followed by hydropriming in distilled water for 24 h, and then stored for six months in the dark before evaluation. The treated cucumber seeds demonstrated a statistically significant enhancement in seed germination and seedling vitality indices. In contrast, broccoli seeds showed no significant improvement. The stimulatory effects observed in cucumber may be attributed to reactive oxygen and nitrogen species, which act as signaling molecules to promote stress tolerance and early growth. This study also highlights the potential of combined NTP treatment and hydropriming as a pre-sowing treatment for select crops, underscoring the need for species-specific optimization. The used, portable, and relatively inexpensive NTP device offers practical advantages for agricultural applications. Full article

Seed germination and early seedling growth are pivotal stages that define crop establishment and yield potential. Conventional agrochemicals used to improve these processes often raise environmental concerns, highlighting the need for sustainable alternatives. In this study, we demonstrated that water treated with cylindrical dielectric barrier discharge (c-DBD) plasma, enriched with nitric oxide (NO) and reactive nitrogen species (RNS), markedly enhanced onion (Allium cepa) seed germination and seedling vigor. The plasma-treated water (PTW) promoted rapid imbibition, broke dormancy, and accelerated germination rates beyond 98%. Seedlings irrigated with PTW exhibited significantly increased biomass, root and shoot length, chlorophyll content, and antioxidant enzyme activities, accompanied by reduced lipid peroxidation. Transcriptomic profiling revealed that PTW orchestrated a multifaceted regulatory network by upregulating gibberellin biosynthesis genes (GA3OX1/2), suppressing abscisic acid signaling components (ABI5), and activating phenylpropanoid metabolic pathways (PAL, 4CL) and antioxidant defense genes (RBOH1, SOD). These molecular changes coincided with elevated NO₂⁻ and NO₃⁻ levels and finely tuned hydrogen peroxide dynamics, underpinning redox signaling crucial for seed activation and stress resilience. Our findings establish plasma-generated NO-enriched water as an innovative, eco-friendly technology that leverages redox and hormone crosstalk to stimulate germination and early growth, offering promising applications in sustainable agriculture. Full article

With the rapid progression of global industrialization and urbanization, emerging contaminants (ECs) have become pervasive in environmental media, posing considerable risks to ecosystems and human health. While multidisciplinary evidence continues to accumulate regarding their environmental persistence and bioaccumulative hazards, critical knowledge gaps persist in understanding their spatiotemporal distribution, cross-media migration mechanisms, and cascading ecotoxicological consequences. This review systematically investigates the global distribution patterns of ECs in aquatic environments over the past five years and evaluates their potential ecological risks. Furthermore, it examines the performance of various treatment technologies, focusing on economic cost, efficiency, and environmental sustainability. Methodologically aligned with PRISMA 2020 guidelines, this study implements dual independent screening protocols, stringent inclusion–exclusion criteria (n = 327 studies). Key findings reveal the following: (1) Occurrences of ECs show geographical clustering in highly industrialized river basins, particularly in Asia (37.05%), Europe (24.31%), and North America (14.01%), where agricultural pharmaceuticals and fluorinated compounds contribute disproportionately to environmental loading. (2) Complex transboundary pollutant transport through atmospheric deposition and oceanic currents, coupled with compound-specific partitioning behaviors across water–sediment–air interfaces. (3) Emerging hybrid treatment systems (e.g., catalytic membrane bioreactors, plasma-assisted advanced oxidation) achieve > 90% removal for recalcitrant ECs, though requiring 15–40% cost reductions for scalable implementation. This work provides actionable insights for developing adaptive regulatory frameworks and advancing green chemistry principles in environmental engineering practice. Full article

Gasification of municipal solid waste and other biogenic residues (e.g., biomass and biowaste) is increasingly recognized as a promising thermochemical pathway for converting non-recyclable fractions into valuable energy carriers, with applications in electricity generation, district heating, hydrogen production, and synthetic fuels. This paper provides a comprehensive analysis of major gasification technologies, including fixed bed, fluidized bed, entrained flow, plasma, supercritical water, microwave-assisted, high-temperature steam, and rotary kiln systems. Key aspects such as feedstock compatibility, operating parameters, technology readiness level, and integration within circular economy frameworks are critically evaluated. A comparative assessment of incineration and pyrolysis highlights the environmental and energetic advantages of gasification. The valorization pathways for main product (syngas) and by-products (syngas, ash, tar, and biochar) are also explored, emphasizing their reuse in environmental, agricultural, and industrial applications. Despite progress, large-scale adoption in Europe is constrained by economic, legislative, and technical barriers. Future research should prioritize scaling emerging systems, optimizing by-product recovery, and improving integration with carbon capture and circular energy infrastructures. Supported by recent European policy frameworks, gasification is positioned to play a key role in sustainable waste-to-energy strategies, biomass valorization, and the transition to a low-emission economy. Full article

Aflatoxins are toxic organic substances that are synthesized on the surfaces of seeds, nuts, and similar products by some fungi under elevated humidity. They decompose at temperatures well above 130 °C, so standard heating or autoclaving is an obsolete technique for the degradation of toxins on surfaces without significant modification of the treated material. Non-equilibrium plasma was used to degrade aflatoxins at low temperatures and determine the efficiency of O atoms. A commercial mixture of aflatoxins was deposited on smooth substrates, and the solvent was evaporated so that about a 3 nm thick film of dry toxins remained on the substrates. The samples were exposed to low-pressure oxygen plasma sustained by an inductively coupled radiofrequency (RF) discharge in either the E or H mode. The gas pressure was 20 Pa, the forward RF power was between 50 and 700 W, and the O-atom flux was between 1.2 × 10²³ and 1.5 × 10²⁴ m⁻² s⁻¹. Plasma treatment caused the rapid degradation of aflatoxins, whose concentration was deduced from the fluorescence signal at 455 nm upon excitation with a monochromatic source at 365 nm. The degradation was faster at higher discharge powers, but the degradation curves fitted well when plotted against the dose of O atoms. The experiments showed that the aflatoxin concentration dropped below the detection limit of the fluorescence probe after receiving the O-atom dose of just above 10²⁵ m⁻². This dose was achieved within 10 s of treatment in plasma in the H mode, and approximately a minute when plasma was in the E mode. The method provides a low-temperature solution for the efficient detoxification of agricultural products. Full article

Heavy metal pollution is a growing public health concern owing to rising environmental pollution throughout the world. The situation is more vulnerable in Bangladesh; therefore, this study assessed contamination levels in different land use categories such as rural, local market, industrial, research, and coastal areas, as well as the related health risks for farmers in Bangladesh. A total of 45 soil samples were considered from three depths (0–5 cm, 5–10 cm, and 10–15 cm) across five different areas, with three replications per depth, following the monsoon season. Samples were prepared using a diacid mixture, and heavy metals (Cu, Ni, Mn, Cr, Zn, Pb) were investigated using Inductively Coupled Plasma Mass Spectrometry (ICP-MS). Health risks were evaluated using standard assessment models. The results showed that coastal agricultural soils had the highest heavy metal concentrations (except Pb), while rural areas had the lowest (except Cu and Ni), with no clear depth-based pattern. Two contamination sources were identified: component 1 (Cu, Ni, Mn, Cr, Zn) and component 2 (Pb, Zn), indicating mixed and anthropogenic sources, respectively. The Pollution Load Index (PLI) was highest in coastal areas and lowest in rural areas. The average daily intake of metals followed the order of inhalation > dermal > ingestion, with inhalation being the primary exposure route. The highest cumulative cancer risk (CCR) was observed in coastal agricultural soils (5.82 × 10⁻⁹), while rural soils had the lowest CCR (8.24 × 10⁻¹⁰), highlighting significant regional differences in health risks. Full article

Sustainable agriculture necessitates innovative solutions to enhance plant growth while optimizing resource efficiency. Plasma discharge generates reactive oxygen and nitrogen species (NH₄⁺, NO₃⁻, and NO₂⁻), which form plasma-activated water upon dissolution, affecting the nutritional solution pH and electrical conductivity (EC) and, consequently, plant development. Four treatments were applied, resulting from combining high or low plasma discharge intensities at 45 or 60 min spray intervals: low plasma discharge with a 45 min interval (T1), low plasma discharge with a 60 min interval (T2), high plasma discharge with a 45 min interval (T3), and high plasma discharge with a 60 min interval (T4). The experiment followed a 4 × 5 × 2 factorial design comprising the four treatments, five replications per treatment, and two independent experimental repeats, resulting in forty experimental units. Each unit contained 12 lettuce plants, for a total of 480 plants. The multivariate analysis of variance confirmed statistically significant treatment effects. The combination of high plasma intensity and a 45 min spray interval significantly increased the growth parameters and yield as compared with the other treatments. In particular, compared with T1, which produced the lowest values across all measured parameters, T3 resulted in a 97% increase in leaf area, a 72% increase in stem diameter, a 49% increase in leaf number, a 44% increase in leaf width, and a 30% increase in leaf length. Additionally, T3 increased edible yield by 210% and total biomass production by 203% compared with T1. These results demonstrate the combined effect of plasma intensity and spraying frequency in optimizing plant development in aeroponic systems. As far as mineral uptake is concerned, T3 increased the nitrogen, potassium, phosphorus, calcium, and magnesium concentrations by 18.2%, 16.7%, 32.3%, 20.2%, and 11.2%, respectively, compared with T1. The regression analysis further validated the robustness of the findings, indicating plasma intensity to be a dominant factor. Enhanced mineral uptake (N, P, K, Ca, and Mg) and consistent growth trends across treatments highlighted the significance of plasma technology in optimizing plant growth, yield, and nutrient absorption, suggesting it is a sustainable and efficient approach to modern agriculture. Full article

Global agriculture remains dependent on nitrogen fertilizers produced through fossil fuel-based processes, contributing to greenhouse gas emissions, energy use, and supply chain vulnerabilities. This review introduces plasma-activated water (PAW) as a novel, electricity-driven alternative for sustainable nitrogen delivery. Generated by non-thermal plasma, PAW infuses water with reactive oxygen and nitrogen species, offering a clean, decentralized substitute for conventional synthetic fertilizers derived from the Haber–Bosch and Ostwald processes. It can be produced on-site using renewable energy, reducing transportation costs and depending on fertilizers. Beyond its fertilizer properties, PAW enhances seed germination, plant growth, stress tolerance, and pest resistance, making it a multifunctional input for controlled environment agriculture. We also assess PAW’s techno-economic viability, including energy requirements, production costs, and potential scalability through renewable energy. These factors are crucial for determining its feasibility in both industrial systems and localized agricultural applications. Finally, the review examines PAW’s contribution to the ten United Nations Sustainable Development Goals, particularly in climate action, clean energy, and sustainable food production. By combining agronomic performance with circular production and emissions reduction, PAW presents a promising path toward more resilient, low-impact, and self-sufficient agricultural systems. Full article

Tomato brown rugose fruit virus (ToBRFV) is an important emerging virus that poses a serious threat to the global agricultural economy. Ubiquitination is one of the key post-translational protein modification types in plant responses to biotic stress, but the extent to which ToBRFV infection alters the overall ubiquitination status has not been reported. This study conducted integrated ubiquitome and proteome analyses of Nicotiana benthamiana leaves infected with ToBRFV and identified differentially ubiquitinated proteins. A total of 346 lysine sites on 302 identified proteins were found to be affected, with 260 sites exhibiting upregulated ubiquitination levels in 224 proteins and 86 sites showing downregulated ubiquitination levels in 80 proteins. The differentially ubiquitinated proteins were primarily localized in the cytoplasm (29%), nucleus (18%), plasma membrane (8.9%), mitochondria (5.1%), and chloroplasts (4.6%). Fourteen conserved ubiquitination motifs, including ENNNK, ENNK, SK, and KNG, were identified. Furthermore, enrichment analysis indicated that ToBRFV infection induces an increase in the ubiquitination levels of proteins associated with ion transport, MAPK signaling pathways, and plant hormone signal transduction, while the ubiquitination levels of proteins related to carbon metabolism and secondary metabolite synthesis decreased. Functional analysis of the three differentially ubiquitinated proteins revealed that a RING/U-box superfamily protein negatively regulates ToBRFV infection. Our work provides the first systematic analysis of the ubiquitination profile in N. benthamiana leaves following ToBRFV infection, providing important resources for further studies on the regulatory mechanisms of ubiquitination in plant responses to ToBRFV. Full article

With the rapid growth of the global population, increasing per capita energy demands, and waste generation, the need for innovative strategies to mitigate greenhouse gas emissions and effective waste management has become paramount. Pyrolysis, a thermochemical conversion process, facilitates the transformation of diverse biomass feedstocks, including agricultural biomass, forestry waste, and other carbonaceous wastes, into valuable biofuels such as bio-oil, biochar, and producer gas. The article reviews the benefits of pyrolysis as an effective and scalable technique for biofuel production from waste biomass. The review describes the different types of pyrolysis processes, such as slow, intermediate, fast, and catalytic, focusing on the effects of process parameters like temperature, heating rate, and residence time on biofuel yields and properties. The review also highlights the configurations and operating principles of different reactors used for pyrolysis, such as fixed bed, fluidized bed, entrained flow, plasma system, and microwaves. The review examines the factors affecting reactor performance, including energy consumption and feedstock attributes while highlighting the necessity of optimizing these systems to improve sustainability and economic feasibility in pyrolysis processes. The diverse value-added applications of biochar, bio-oil, and producer gas obtained from biomass pyrolysis are also discussed. Full article

Heavy metal pollution poses a significant threat to aquatic ecosystems and drinking water sources, necessitating comprehensive environmental assessments. This study investigated the spatial distribution, potential ecological risks, and sources of heavy metals in the surface sediments of Wanfeng Lake to inform effective pollution management strategies. Twelve sediment samples were collected and analyzed for eight heavy metals (Hg, As, Cu, Pb, Cd, Cr, Ni, Zn) using inductively coupled plasma mass spectrometry. The geo-accumulation index (I_geo) and potential ecological risk index (RI) were applied to assess contamination levels and ecological risks. Cluster analysis and Kriging interpolation were used to identify potential pollution sources and spatial patterns. Results revealed that heavy metal concentrations decreased in the order Zn > Pb > Cu > Cr > Ni > As > Cd > Hg, with Hg concentrations exceeding the national average for Chinese lake sediments. Ecological risk assessments identified Hg (0.06 μg/g) and Cd (0.10 μg/g) as the priority pollutants. The Hg posed a moderate ecological risk, particularly in upstream areas, while Cd pollution was concentrated downstream. Atmospheric deposition was identified as the primary source of Hg, whereas agricultural activities were determined to be the main driver of Cd contamination. These findings provide a scientific basis for developing targeted pollution control measures in Wanfeng Lake. Full article

This paper presents a comprehensive analysis of recent advancements in the application of thermal spraying techniques to enhance the durability and wear resistance of agricultural machinery components, with a particular focus on disc harrow assemblies. Given the harsh conditions under which tillage tools operate—characterized by abrasive wear, impact stresses, and chemical exposure from various soil types—thermal sprayed coatings have emerged as a viable solution to extend the service life of these components. The study discusses various deposition methods, particularly Atmospheric Plasma Spraying (APS), and evaluates their effectiveness in creating high-performance surface layers that resist wear, corrosion, and mechanical degradation. The review also summarizes experimental and field test results for coatings based on materials such as NiCrBSi, WC-Co-Cr, TiO₂, Al₂O₃, Cr₂O_3, and ceramic–metal composites, highlighting their significant improvements in hardness, friction reduction, and resistance to delamination and oxidation. The paper highlights research using thermal spraying techniques, especially APS for agricultural applications, with emphasis mostly on components intended for soil processing and requiring good resistance to abrasive wear. Full article

Due to the environmental concerns surrounding widely used antimicrobial agents, the use of nanotechnology to suppress crop diseases has attracted increasing attention in the agricultural field. This paper investigated the inhibitory effects of manganese-based nanomaterials (NMs) on rice leaf blight. In vitro experiments showed that manganese oxide (MnO₂) NMs and manganese tetroxide (Mn₃O₄) NMs directly inhibited Xanthomonas oryzae (Xoo) with a maximum OD value of 0.177, which was 11.5% lower than the control. In vivo experiments demonstrated that spraying MnO₂ NMs and Mn₃O₄ NMs reduced the diseased leaf length to 22–28% and 25–26%, respectively. This is due to Mn-based NMs inducing enhanced plant resistance by increasing the activity of phenylalanine ammonia–lyase in rice leaves by 36–61%. Single particle inductively coupled plasma mass spectrometry showed that Mn₃O₄ NMs are more frequently retained as NMs in rice than MnO₂ NMs, resulting in enhanced antimicrobial effects. Mn-based NMs exhibit strong antimicrobial activity and hold significant promise as alternatives for plant protection and agricultural applications; however, careful consideration must be given to their concentrations and application methods. Full article

Cold atmospheric plasma (CAP) is a novel and versatile technology, which is not yet used in the food and agricultural sector for barley processing. In lab-scale applications, the technology shows potential in extending shelf life and ensuring food safety and quality, e.g., during storage. CAP reactive nature counteracts insect pests, fungi, and bacteria, but also improves seed germination and facilitates plant growth not only under stress conditions. Its generation does not require water, chemicals, or solvents and consumes little energy due to low operating temperatures (<60 °C) with a short time span that makes additional production steps (e.g., cooling) obsolete. Therefore, CAP is a sustainable technology capable of further optimising the use of limited resources with the potential of offering solutions for upcoming environmental challenges and political requirements for replacing existing practices and technologies due to the growing impact of climate change. This review summarises recent developments and findings concerning CAP application in barley production and processing with air as the process gas. Furthermore, this comprehensive overview could help identify further research needs to overcome its current technical limitations, e.g., efficiency, capacity, etc., that hamper the upscale and market introduction of this environmentally friendly technology. Full article