Search Results (5,472)

Freeze–thaw damage is one of the most important factors affecting the durability of concrete in cold regions, and how to quantitatively characterize the effect of freeze–thaw cycles on the degree of damage of concrete is a widely concerning issue among researchers. Based on the hydraulic pressure theory, a new concrete freeze–thaw damage model was proposed by assuming the defect development mode of concrete during freeze–thaw cycles. The model shows that the total amount of defects due to freeze–thaw damage is related to the initial defects and the defect development capacity within the concrete. Based on the new freeze–thaw damage model, an equation for the loss of relative dynamic elastic modulus of concrete during freeze–thaw cycles was established using the relative dynamic elastic modulus of concrete as the defect indicator. In order to validate the damage model using relative dynamic elastic modulus as the defect index, freeze–thaw cycle tests of four kinds of concrete with different air content were carried out, and the rationality of the model was verified by the relative dynamic elastic modulus of concrete measured under different freeze–thaw cycling periods. On this basis, a freeze–thaw damage model of concrete was established considering the effect of air content in concrete. In addition, the model proposed in this paper was supplemented and validated by experimental data from other researchers. The results show that the prediction model proposed in this study is not only easy to apply and has clear physical meaning but also has high accuracy and general applicability, which provides support for predicting the degree of freeze–thaw damage of concrete structures in cold regions. Full article

Monitoring the height of secondary forest regrowth is essential for assessing ecosystem recovery, but current methods rely on field surveys, airborne or UAV LiDAR, and 3D reconstruction from high-resolution UAV imagery, which are often costly or limited by logistical constraints. Here, we address the challenge of scaling up canopy height monitoring by evaluating a recent deep learning model, trained on data from the Amazon and Atlantic Forests, developed to extract canopy height from RGB-NIR Planet NICFI imagery. The research questions are as follows: (i) How are canopy height estimates from the model affected by slope and orientation in natural forests, based on a large and well-balanced experimental design? (ii) How effectively does the model capture the growth trajectories of Pinus and Eucalyptus plantations over an eight-year period following planting? We find that the model closely tracks Pinus growth at the parcel scale, with predictions generally within one standard deviation of UAV-derived heights. For Eucalyptus, while growth is detected, the model consistently underestimates height, by more than 10 m in some cases, until late in the cycle when the canopy becomes less dense. In stable natural forests, the model reveals seasonal artifacts driven by topographic variables (slope × aspect × day of year), for which we propose strategies to reduce their influence. These results highlight the model’s potential as a cost-effective and scalable alternative to field-based and LiDAR methods, enabling broad-scale monitoring of forest regrowth and contributing to innovation in remote sensing for forest dynamics assessment. Full article

Understanding changes in land use structures under multiple scenarios and their impacts on carbon storage is essential for revealing the evolution of regional development patterns and the underlying mechanisms of carbon cycle dynamics. This study adopted an integrated PLUS-InVEST modeling framework to analyze and predict changes in carbon storage in the Central Plains Urban Agglomeration (CPUA) under different scenarios for the years 2030 and 2060. The results showed the following: (1) From 2000 to 2020, the areas of forest land, water bodies, and construction land expanded, while the areas of cropland, grassland, and barren land decreased. Over this 20-year period, carbon storage showed a declining trend, decreasing from 2390.07 × 10⁶ t in 2000 to 2372.19 × 10⁶ t in 2020. (2) In both 2030 and 2060, cropland remained the primary land use type in the CPUA. Overall, carbon storage in the CPUA was higher in the southwestern area and decreased in the central and eastern parts, which was mainly related to the land use distribution pattern in the CPUA. (3) Carbon storage under the EP (ecological protection) and CP (cropland protection) scenarios was significantly higher than under the other two scenarios, and in 2030, carbon storage under the CP and EP scenarios exceeded that in 2020, while the UD (urban development) scenario had the lowest total carbon storage. This indicated that the expansion of construction land was detrimental to carbon storage enhancement, underscoring the importance of implementing ecological protection strategies. In summary, the results of this study quantitatively reflected the changes in carbon storage in the CPUA under different future development scenarios, providing a reference for formulating regional development strategies. Full article

Mushroom production is a sustainable practice but requires improvements, such as in Lentinula edodes (Berk) Pegler cultivation, which has high water and labor demands. In this context, this study proposed replacing the traditional primordia induction method by submersion with a water injection method. Two primordia induction methods (submersion and injection) and two cultivation block formats were compared: rectangular cube (2 kg) and cylindrical (3.5 kg). The substrate, composed of eucalyptus sawdust (72%), wheat bran (12.5%), rice bran (12.5%), CaCO₃ (1%), and CaSO₄ (2%), was inoculated with strain LED 19/11 and incubated for 80 days at 26 ± 5 °C and 85 ± 15% humidity. After this period, the blocks were washed and transferred to the production environment. Fruiting was induced either by submersion or water injection, and production was evaluated over four harvest flushes. The 2 kg blocks had higher yields with submersion (16.62%), while the 3.5 kg blocks responded better to injection (13.01%), showing more homogeneous production. Increasing the substrate quantity contributes to greater harvest stability across production cycles. Water injections proved to be a viable alternative, reducing handling and facilitating large-scale production. The use of this technique demonstrates great importance in reducing water use and also the need for labor in cultivation. Full article

Modernizing irrigation systems (ISs) from traditional gravity methods to sprinkler and drip technologies has significantly improved water use efficiency. However, it has simultaneously increased electricity demand and operational costs. Integrating photovoltaic generators into ISs represents a promising solution, as solar energy availability typically aligns with peak irrigation periods. Despite this potential, photovoltaic pumping systems (PVPSs) often face reliability issues due to fluctuations in solar irradiance, resulting in frequent start/stop cycles and premature equipment wear. The IEC 62253 standard establishes procedures for evaluating PVPS performance but primarily addresses steady-state conditions, neglecting transient regimes. As the main contribution, the current paper proposes a non-intrusive, high-resolution monitoring system and a methodology to assess the performance of an isolated, high-power PVPS, considering also transient regimes. The system records critical electrical, hydraulic and environmental parameters every second, enabling in-depth analysis under various weather conditions. Two performance indicators, pumped volume efficiency and equivalent operating time, were used to evaluate the system’s performance. The results indicate that near-optimal performance is only achievable under clear sky conditions. Under the appearance of clouds, control strategies designed to protect the system reduce overall efficiency. The proposed methodology enables detailed performance diagnostics and supports the development of more robust PVPSs. Full article

Dyes are widely used in various industries, but their removal from wastewater remains a challenge due to their resistance to biodegradation. While substantial research exists regarding the removal of individual dyes, there is much less about the removal of their mixtures. The aim of the research was to determine the possibility of using the immobilised mycelium of Pleurotus ostreatus strains to remove three-component mixtures of dyes from different classes. Efficiency of the removal in the continuously aerated reactor was similar to that obtained in a periodically aerated reactor and was over 90% at the end of each cycle. Despite the addition of subsequent portions of dyes, no increase in the toxicity of post-process samples was observed, and even a decrease in zootoxicity was noticed. The results of the study therefore indicate that an immobilised biomass can be used to remove the dyes, without the need to constantly inject air into the reactor. Full article

The main advantage of using biomass for energy generation is the reduction in carbon dioxide emissions. For a fast reduction effect, it is important to use biomass characterised by an annual growth cycle. These may be fallen leaves. The fuel properties of the leaves can change during the growth period. These changes can result from both the natural growth process and environmental factors—particulate matter adsorption. The main objective was to determine changes in the characteristics of leaves and needles during the growth period (from May to October). Furthermore, to determine the effect of adsorbed particulate matter, the washing process was carried out. Studies were carried out for three tree species: Norway maple, horse chestnut and European larch. Proximate and ultimate analysis was performed and mercury content was determined. During the growth period, beneficial changes were observed: an increase in carbon content and a decrease in hydrogen and sulphur content. The unfavourable change was a significant increase in ash content, which caused a decrease in calorific value. The increase in ash content was caused by adsorbed particulate matter. They were mostly absorbed by the tissues of the needle and leaves and could not be removed by washing the surface. Full article

The Complementary Relationship (CR) principle of evapotranspiration provides an efficient approach for estimating actual evapotranspiration (ET_a), owing to its simplified computation and effectiveness in utilizing meteorological factors. Accurate estimation of actual evapotranspiration (ET_a) is crucial for understanding surface energy and water cycles, especially in permafrost regions. This study aims to evaluate the applicability of two Complementary Relationship (CR)-based methods—Bouchet’s in 1963 and Brutsaert’s in 2015—for estimating ETa on the Qinghai–Tibetan Plateau (QTP), using observations from Eddy Covariance (EC) systems. The potential evapotranspiration (ET_p) was calculated using the Penman equation with two wind functions: the Rome wind function and the Monin–Obukhov Similarity Theory (MOST). The comparison revealed that Bouchet’s method underestimated ET_a during frozen soil periods and overestimated it during thawed periods. In contrast, Brutsaert’s method combined with the MOST yielded the lowest RMSE values (0.67–0.70 mm/day) and the highest correlation coefficients (r > 0.85), indicating superior performance. Sensitivity analysis showed that net radiation (Rn) had the strongest influence on ET_a, with a daily sensitivity coefficient of up to 1.35. This study highlights the improved accuracy and reliability of Brutsaert’s CR method in cold alpine environments, underscoring the importance of considering freeze–thaw dynamics in ET modeling. Future research should incorporate seasonal calibration of key parameters (e.g., ε) to further reduce uncertainty. Full article

During the Pleistocene, the successive ice ages prompted the southward expansion of the “Mammoth Steppe” ecosystem, a prevalent habitat that supported species adapted to cold environments such as the mammoth, woolly rhinoceros, and reindeer. Previously, the earliest evidence for such cold-adapted species in the Iberian Peninsula dated back to Marine Isotope Stage 6 (MIS 6, ~191–123 ka). This paper reports the discovery of a reindeer (Rangifer) tooth from Unit GIII of the Galería site at the Atapuerca-Trinchera site complex, dated to MIS 8 (~300–243 ka). This find is significant as it represents not only the oldest evidence of glacial fauna in the Iberian Peninsula but also the southernmost occurrence of reindeer in Europe of this age. The presence of Rangifer at this latitude (42°21′ N) during MIS 8 suggests that the glacial conditions affected the Iberian fauna earlier and with greater intensity than previously understood. Over the subsequent climatic cycles, cold-adapted species spread further south, reaching Madrid (40°20′) during the penultimate glacial period and the province of Granada (37°01′) during the last glacial maximum. The coexistence of human fossils and lithic artefacts within Units GII and GIII at Galería indicates that early humans also inhabited these glacial environments at Atapuerca. This study elaborates on the morphological and archaeological significance of the reindeer fossil, emphasizing its role in understanding the biogeographical patterns of glacial fauna and the adaptability of Middle Pleistocene human populations. Full article

China is one of the countries severely affected by earthquakes, making precise and timely identification of earthquake precursors essential for reducing casualties and property damage. A novel method is proposed that combines a rock acoustic emission (AE) detection technique with deep learning methods to facilitate real-time monitoring and advance earthquake precursor detection. The AE equipment and seismometers were installed in a granite tunnel 150 m deep in the mountains of eastern Guangdong, China, allowing for the collection of experimental data on the correlation between rock AE and seismic activity. The deep learning model uses features from rock AE time series, including AE events, rate, frequency, and amplitude, as inputs, and estimates the likelihood of seismic events as the output. Precursor features are extracted to create the AE and seismic dataset, and three deep learning models are trained using neural networks, with validation and testing. The results show that after 1000 training cycles, the deep learning model achieves an accuracy of 98.7% on the validation set. On the test set, it reaches a recognition accuracy of 97.6%, with a recall rate of 99.6% and an F₁ score of 0.975. Additionally, it successfully identified the two biggest seismic events during the monitoring period, confirming its effectiveness in practical applications. Compared to traditional analysis methods, the deep learning model can automatically process and analyse recorded massive AE data, enabling real-time monitoring of seismic events and timely earthquake warning in the future. This study serves as a valuable reference for earthquake disaster prevention and intelligent early warning. Full article

Tillage is a major factor influencing soil biological communities, particularly earthworms, which play a key role in soil structure and nutrient cycling. To address soil degradation, less-intensive tillage practices are increasingly being adopted globally and have shown positive effects on earthworm populations when applied consistently over extended periods. However, understanding of the earthworm population dynamics in the period following the implementation of changes in tillage practices remains limited. This three-year field study (2021–2023) investigates earthworm populations during the early transition phase (4–6 years) following the conversion from conventional ploughing to conservation (<8 cm depth, with residue retention) and no-tillage systems in a temperate arable system in central Slovenia. Earthworms were sampled annually in early October from three adjacent fields, each following the same three-year crop rotation (maize—winter cereal + cover crop—soybeans), using a combination of hand-sorting and allyl isothiocyanate (AITC) extraction. Results showed that reduced tillage practices significantly increased both earthworm biomass and abundance compared to conventional ploughing. However, a significant interaction between tillage and year was observed, with a sharp decline in earthworm abundance and mass in 2022, likely driven by a combination of 2022 summer tillage prior to cover crop sowing and extreme drought conditions. Juvenile earthworms were especially affected, with their proportion decreasing from 62% to 34% in ploughed plots and from 63% to 26% in conservation tillage plots. Despite interannual fluctuations, no-till showed the lowest variability in earthworm population. Long-term monitoring is essential to disentangle management and environmental effects and to inform resilient soil management strategies. Full article

Background: Artificial intelligence (AI) and machine learning (ML) have been reshaping maternal, fetal, neonatal, and reproductive healthcare by enhancing risk prediction, diagnostic accuracy, and operational efficiency across the perinatal continuum. However, no comprehensive synthesis has yet been published. Objective: To conduct a scoping review of reviews of AI/ML applications spanning reproductive, prenatal, postpartum, neonatal, and early child-development care. Methods: We searched PubMed, Embase, the Cochrane Library, Web of Science, and Scopus through April 2025. Two reviewers independently screened records, extracted data, and assessed methodological quality using AMSTAR 2 for systematic reviews, ROBIS for bias assessment, SANRA for narrative reviews, and JBI guidance for scoping reviews. Results: Thirty-nine reviews met our inclusion criteria. In preconception and fertility treatment, convolutional neural network-based platforms can identify viable embryos and key sperm parameters with over 90 percent accuracy, and machine-learning models can personalize follicle-stimulating hormone regimens to boost mature oocyte yield while reducing overall medication use. Digital sexual-health chatbots have enhanced patient education, pre-exposure prophylaxis adherence, and safer sexual behaviors, although data-privacy safeguards and bias mitigation remain priorities. During pregnancy, advanced deep-learning models can segment fetal anatomy on ultrasound images with more than 90 percent overlap compared to expert annotations and can detect anomalies with sensitivity exceeding 93 percent. Predictive biometric tools can estimate gestational age within one week with accuracy and fetal weight within approximately 190 g. In the postpartum period, AI-driven decision-support systems and conversational agents can facilitate early screening for depression and can guide follow-up care. Wearable sensors enable remote monitoring of maternal blood pressure and heart rate to support timely clinical intervention. Within neonatal care, the Heart Rate Observation (HeRO) system has reduced mortality among very low-birth-weight infants by roughly 20 percent, and additional AI models can predict neonatal sepsis, retinopathy of prematurity, and necrotizing enterocolitis with area-under-the-curve values above 0.80. From an operational standpoint, automated ultrasound workflows deliver biometric measurements at about 14 milliseconds per frame, and dynamic scheduling in IVF laboratories lowers staff workload and per-cycle costs. Home-monitoring platforms for pregnant women are associated with 7–11 percent reductions in maternal mortality and preeclampsia incidence. Despite these advances, most evidence derives from retrospective, single-center studies with limited external validation. Low-resource settings, especially in Sub-Saharan Africa, remain under-represented, and few AI solutions are fully embedded in electronic health records. Conclusions: AI holds transformative promise for perinatal care but will require prospective multicenter validation, equity-centered design, robust governance, transparent fairness audits, and seamless electronic health record integration to translate these innovations into routine practice and improve maternal and neonatal outcomes. Full article

The main soil type in the Sanjiang Plain of Northeast China, dryland albic soil is of great significance for studying nutrient distribution characteristics. This study focuses on 852 Farm in the typical dryland albic soil area of the Sanjiang Plain, using a combination of paired t-test, geostatistics, correlation analysis, and principal component analysis to systematically reveal the spatial differentiation of soil nutrients in the black soil layer and white clay layer of dryland albic soil, and to clarify the impact mechanism of plow layer nutrient characteristics on crop productivity. The results show that the nutrient content order in both the black and white clay layers is consistent: total potassium (TK) > organic matter (OM) > total nitrogen (TN) > total phosphorus (TP) > alkali-hydrolyzable nitrogen (HN) > available potassium (AK) > available phosphorus (AP). Both layers exhibit a spatial pattern of overall consistency and local differentiation, with spatial heterogeneity dominated by altitude gradients—nutrient content increases with decreasing altitude. Significant differences exist in nutrient content and distribution between the black and white clay layers, with the comprehensive fertility of the black layer being significantly higher than that of the white clay layer, particularly for TN, TP, TK, HN, and OM contents (effect size > 8). NDVI during the full maize growth period is significantly positively correlated with TP, TN, AK, AP, and HN, and the NDVI dynamics (first increasing. then decreasing) closely align with the peak periods of available nitrogen/phosphorus and crop growth cycles, indicating a strong coupling relationship between vegetation biomass accumulation and nutrient availability. These findings provide important references for guiding rational fertilization, agricultural production layout, and ecological environmental protection, contributing to the sustainable utilization of dryland albic soil resources and sustainable agricultural development. Full article

The main bearing of a tunnel boring machine (TBM) is a critical component of the main driving system that enables continuous excavation, and its performance is crucial for ensuring the safe operation of the TBM. Currently, there are few testing technologies for TBM main bearings, and a comprehensive testing and evaluation system has yet to be established. This study presents an experimental investigation using a self-developed, full-scale TBM main bearing test bench. Based on a representative load spectrum, both operational condition tests and life cycle tests are conducted alternately, during which the signals of the main bearing are collected. The observed vibration signals are weak, with significant vibration attenuation occurring in the large structural components. Compared with the test bearing, which reaches a vibration amplitude of 10 g in scale tests, the difference is several orders of magnitude smaller. To effectively utilize the selected evaluation indicators, the entropy weight method is employed to assign weights to the indicators, and a comprehensive analysis is conducted using grey relational analysis. This strategy results in the development of a comprehensive evaluation method based on entropy weighting and grey relational analysis. The main bearing performance is evaluated under various working conditions and the same working conditions in different time periods. The results show that the greater the bearing load, the lower the comprehensive evaluation coefficient of bearing performance. A multistage evaluation method is adopted to evaluate the performance and condition of the main bearing across multiple working scenarios. With the increase of the test duration, the bearing performance exhibits gradual degradation, aligning with the expected outcomes. The findings demonstrate that the proposed performance evaluation method can effectively and accurately evaluate the performance of TBM main bearings, providing theoretical and technical support for the safe operation of TBMs. Full article

Disruption of circadian rhythms by abnormal light exposure and reduced melatonin secretion has been linked to heightened pain sensitivity and opioid tolerance. This study evaluated how environmental light manipulation and exogenous melatonin supplementation influence pain perception and morphine tolerance in a rat model of neuropathic pain induced by partial sciatic nerve transection (PSNT). Rats were exposed to constant darkness, constant light, or a 12 h/12 h light–dark cycle for one week before PSNT surgery. Behavioral assays and continuous intrathecal (i.t.) infusion of morphine, melatonin, or their combination were conducted over a 7-day period beginning immediately after PSNT. On Day 7, after discontinued drugs infusion, an acute intrathecal morphine challenge (15 µg, i.t.) was administered to assess tolerance expression. Constant light suppressed melatonin levels, exacerbated pain behaviors, and accelerated morphine tolerance. In contrast, circadian-aligned lighting preserved melatonin rhythms and mitigated these effects. Melatonin co-infusion attenuated morphine tolerance and enhanced morphine analgesia. Reduced pro-inflammatory cytokine expression and increase anti-inflammatory cytokine IL-10 level and suppressed astrocyte activation were also observed by melatonin co-infusion during morphine tolerance induction. These findings highlight the potential of melatonin and circadian regulation in improving opioid efficacy and reduced morphine tolerance in managing neuropathic pain. Full article