Search Results (1,729)

To address the issues of high energy consumption and unstable construction quality caused by high-temperature heating during the preparation of traditional hot-mixed/grouted semi-flexible pavement (SFP) mixtures, a cold-mixed integrated (CMI) process was proposed. In addition, the material composition of the mixtures was optimized. The effects of the preparation process and binder type on the high- and low-temperature performance, water stability, and fatigue performance were then analyzed. Furthermore, the microstructural characteristics of the semi-flexible mixture were also investigated. The results indicated that the CMI process facilitated the formation and uniform distribution of calcium silicate hydrate (C-S-H), enhanced the binder’s ability to encapsulate aggregates and fill skeletal voids, significantly reduced the mixture’s void ratio, and improved its pavement performance. The proposed procedure was a means of enhancing high-temperature stability and fatigue life (an increase of 80% and 200 times compared to the hot-mixed/grouted (HMG) process, and 5 times and 300 times compared to AC-13, respectively). Compared with the HMG process, the CMI process offered greater advantages in enhancing the high-temperature stability and fatigue resistance of the mixture, particularly when using SBS-modified asphalt, where fatigue performance exhibited an order-of-magnitude improvement. Furthermore, while SBS modification could improve the road performance of SFP materials, mixtures prepared with SBS-modified emulsified asphalt demonstrated more significant enhancements in high-temperature stability and fatigue resistance, approximately 2 times and 10 times higher than SBS-modified mixtures, respectively. The addition of styrene–acrylic emulsion (SAE) could further enhance the low-temperature crack resistance by approximately 7%. The research results can provide a reference for the development and application of preparation processes for semi-flexible mixtures. Full article

Asphalt pavement on rigid base (cement concrete) differs significantly from traditional granular base pavement. To investigate its mechanical behavior, a viscoelastic–viscoplastic damage constitutive model for asphalt mixtures is proposed and verified. A user-material subroutine (UMAT) is developed to implement the model, and a three-dimensional finite element model is established to analyze pavement responses under various working conditions. Key numerical results include the following: the asphalt layer primarily experiences compressive–shear failure, with peak shear stress (τ₁₂) reaching 141.6 kPa under rigid base conditions; emergency braking increases τ₁₂ to approximately 270.3 kPa, a 91% increase; increasing vehicle speed from 15 m/s to 35 m/s raises τ₁₂ by 36.7%; based on stress analysis alone, the recommended asphalt layer thickness is between 0.10 m and 0.14 m, as thickness beyond 0.10 m yields diminishing stress reduction. The findings provide references for performance prediction, structural design, and material development of asphalt pavement on a rigid base. Full article

In this study, the characteristics of concretes made from mixed recycled aggregate—the cheapest and most common secondary raw material in construction and demolition waste—were determined. For this study, besides experimental concretes using mixed recycled aggregate, reference compositions were developed using river gravel, recycled concrete aggregate, and recycled masonry aggregate. The workability of concrete mixtures was measured as class S1, which is acceptable for use with slipform concrete pavers, and was achieved by varying the water/cement ratio, considering the different water adsorptions of the concrete fillers. The following mechanical characteristics of the concretes were defined on the 3rd and 28th days: density, compressive strength, flexural strength, water absorption, and frost resistance. The test results showed sufficiently high indicators of strength and durability for the recycled aggregate concretes. Moreover, the strength of the concrete developed from mixed recycled aggregate was comparable with that of the reference concretes. Considering the low strength requirements for the construction of the lower layers of rigid pavements, it was established that such an application of recycled aggregate concrete, including that derived from mixed recycled aggregate, could be permitted. Full article

Road pavement rehabilitation increasingly incorporates innovative surface technologies aimed at improving pavement performance while reducing environmental impacts. In addition to conventional recycled asphalt pavement (RAP) maintenance strategies, advanced pavement surface systems such as reflective coatings, rejuvenator-based self-healing mixtures, and thin low-noise asphalt layers have been developed to enhance durability and functional performance. This study presents a comparative Life Cycle Assessment (LCA) of four pavement surface technologies using primary inventory data obtained from full-scale road sections. The systems evaluated include a conventional maintenance mixture and three alternative surface solutions: reflective pavement coatings, RAP mixtures incorporating rejuvenator-based self-healing systems, and thin low-noise asphalt layers. The assessment follows ISO 14040 and ISO 14044 standards and applies the ILCD 2011 midpoint+ (EF 2.0) method. To enable comparability between technologies with different durability, the functional unit was defined as 1 m² of rehabilitated pavement per year of service life. The results indicate that thin low-noise asphalt layers provide the highest environmental benefits across most impact categories due to significant material savings associated with reduced layer thickness. Reflective pavement coatings decrease several impacts, particularly fossil resource depletion and atmospheric emissions, although higher burdens are observed in some categories due to synthetic binder production. RAP mixtures incorporating rejuvenator-based self-healing systems improve resource efficiency and extend pavement durability but may increase impacts associated with binder manufacturing. Overall, the findings highlight relevant environmental trade-offs between different pavement surface technologies and demonstrate that parameters such as layer thickness, binder composition, recycled material content, and service life strongly influence environmental performance. The study illustrates how comparative Life Cycle Assessment supports the development and selection of more sustainable pavement surface systems. Full article

Under long-term cyclic loading, the cumulative plastic deformation of unsaturated sandy subgrade is a key control factor for the pavement’s service performance. However, its evolution mechanism and quantitative characterization still lack a universal model. In this study, based on the GDS dynamic triaxial system, a series of cyclic tests were conducted under different conditions: matric suction from 0 to 90 kPa, net confining pressure from 30 to 120 kPa, dynamic stress amplitude from 60 to 240 kPa, and compaction degrees of 87–96%, reaching a total of 10,000 cycles. The results reveal that the permanent deformation of unsaturated sandy subgrade material evolves through three stages: fast, slow, and stable. The deformation is exponentially negatively correlated with matric suction, net confining pressure, and compaction degree, and exponentially positively correlated with dynamic stress amplitude. A coupling prediction model was developed by embedding matric suction and compaction degree factors into the Karg model. This model incorporates net confining pressure, dynamic stress amplitude, matric suction, and compaction degree. By using a normalized master curve method, the permanent deformation curves under different working conditions were compressed into a unique dimensionless function. The parameters have clear physical significance and allow for a unified description across stress, suction, state, and soil types. Experimental data, along with data from the literature, were used to validate the model, showing prediction errors of less than 10% and R² > 0.95. The model provides a simple, high-precision, and transferable theoretical tool for long-service-life subgrade deformation control. Full article

The urban heat island effect is strongly linked to the use of dense mineral pavements with high thermal inertia and lacking passive heat dissipation mechanisms. This article evaluates the potential of evaporatively cooled concrete pavers, based on capillary action and evaporation by incorporating recycled, bio-based, and lightweight materials to develop functional porosity. Ten paver formulations were developed using natural or recycled sand, hemp fibers and shives, and lightweight aggregates. Compressive strength, density, capillary absorption, and thermal behavior were characterized. Tests were conducted outdoors in full sunlight over 48 h in comparison with reference urban materials. The results show that capillary action alone is insufficient to induce effective cooling. The raw recycled sand formulation exhibits high capillary absorption but reaches maximum temperatures of 43–44 °C, which may be due to its low interconnected porosity that limits evaporation. Conversely, formulations incorporating bio-based materials or lightweight aggregates showed a more favorable balance between water availability, reduced density, and surface cooling performance. Hemp-based pavers reach maximum temperatures of 38–40 °C, while those incorporating expanded clay range between 37 and 39 °C, representing a reduction of 7 to 13 °C compared to bitumen and maintaining mechanical strengths suitable for pedestrian use. The results suggest that effective evaporative cooling is associated with sufficient capillary absorption, efficient water transfer toward the surface, and moderate density limiting heat storage. This study demonstrates that high capillary absorption alone does not ensure effective evaporative cooling. By systematically comparing recycled, bio-based and lightweight aggregates, the results reveal that evaporative cooling efficiency probably depends on the functional connectivity of the pore network and on a moderate material density limiting heat storage. Full article

Under long-term heavy load and complex service environments, polyurethane-modified asphalt (PUMA) struggles to simultaneously satisfy the requirements of rutting and cracking resistance of asphalt pavements, as cyclic stress loading reduces the elastic recovery and low-temperature toughness of polyurethane (PU). To address this issue, this study employed hydroxylated crumb rubber (HCR), which is obtained by activating the surface of crumb rubber (CR) and can chemically crosslink with PU in asphalt to form a crosslinked network structure. The aim was to enhance the rutting and cracking resistance of PUMA by utilizing the elasticity and low-temperature toughness of CR. An orthogonal design was employed to systematically design a modified asphalt formulation with PU and HCR (PU/HCRMA) by controlling the isocyanate index and the contents of PU and HCR. The basic properties, rheological properties, and viscoelastic properties of PU/HCRMA were systematically investigated. The results demonstrate that the rutting and cracking resistance of PU/HCRMA are substantially enhanced, with an improvement of 28.91% in the rutting factor at 64 °C compared to PUMA and a reduction of 49.93 MPa in the stiffness modulus at −24 °C. Simultaneously, incorporating HCR in PUMA enhances its viscosity and flow resistance while reducing temperature susceptibility. Furthermore, by providing load-bearing sites, HCR endows PU/HCRMA with exceptional elastic recovery and deformation resistance. Results from FTIR and FM confirm the reaction between isocyanate groups in the PU prepolymer and the hydroxyl groups on the surface of HCR and the formation of HCR-PU crosslinked networks. Finally, PU/HCRMA asphalt mixtures demonstrate significant improvements in both rutting and cracking resistance. This research outcome provides a new direction for the development of high-performance road asphalt materials. Full article

This paper develops a shock-absorbing asphalt mixture for pedestrian pavements that mitigates the impact of normal walking on pedestrians’ bodies by incorporating crumb rubber from recycled tires to produce a soft mixture. This aims to reduce injuries to vulnerable road users, enable the rethinking of urban pavement designs, and address the major challenges facing societies, ultimately achieving more sustainable, resilient, and safer cities. To promote land sustainability, the designed asphalt mixture should be pervious, allowing water to infiltrate into the underlying soil. The development of the asphalt mixture followed an experimental methodology that involved formulating asphalt mixtures with conventional bitumen, polymer-modified bitumen, and bituminous emulsion. The shock-absorbing capability was evaluated by measuring the deformation of the asphalt mixture over time in response to a falling weight from a Light Falling Weight Deflectometer. Permeability capabilities were assessed through the permeability test. Subsequently, the asphalt mixture was characterized according to its macrotexture, friction, air void content, rutting resistance, and stiffness to assess its suitability as a walking surface material. Results indicate that increasing rubber content enhances deformation capacity and improves cushioning but reduces stiffness. Among the solutions, mixtures with polymer-modified bitumen and intermediate rubber content achieved the balance between impact attenuation and mechanical performance. Full article

Motor vehicle exhaust in urban tunnels can cause nitric oxide (NO) to accumulate, severely degrading air quality both inside the tunnel and in the surrounding environment. Photocatalytic technology is an efficient, secondary-pollution-free approach with clear potential for treating tunnel exhaust; however, parametric analyses for practical tunnel engineering applications remain limited. Using computational fluid dynamics (CFD), this study developed a numerical model to simulate photocatalytic NO degradation in a congested tunnel and examined how the surface reaction rate, coating extent, and longitudinal coated section affect NO reduction performance. The results show that NO reduction efficiency increased with the surface reaction rate; however, once the surface reaction rate constant exceeded 2.11 × 10⁻⁴ m/s, further gains diminished and the efficiency approached a plateau due to mass-transfer limitations. With respect to the coating extent, full four-wall coating (sidewalls, ceiling, and road surface) provided the best performance, followed by three-wall coating (excluding the ceiling). Moreover, because the road surface lies in a region of high pollutant concentration and low air velocity, coating on the road surface achieved a markedly stronger reduction effect than coating on the sidewalls or the ceiling. In the simulated 500 m tunnel, the downstream coated section achieved a markedly higher NO reduction efficiency in the ambient environment outside the tunnel (5.9%) than the upstream coated section (1.0%), approaching that of the full-length (500 m) coated section (6.6%). Therefore, in practical engineering applications, priority should be given to coating strategies targeting the downstream section and the road surface in order to balance NO reduction performance and economic cost. Such a strategy is beneficial not only for improving tunnel air quality, but also for promoting sustainable pavement and tunnel-surface engineering by reducing unnecessary coating area and enabling a more resource-efficient and cost-effective use of photocatalytic materials. These findings provide theoretical and methodological support for the sustainable design and application of photocatalytic coating systems in urban tunnels. Full article

Asphalt pavements are essential to modern transport infrastructure but remain highly dependent on virgin aggregates and petroleum-based binders, resulting in high energy demand and significant greenhouse gas emissions. In response, research has advanced recycled-material solutions and low-temperature asphalt technologies. However, sustainability is still often inferred from isolated environmental indicators, without consistent consideration of mechanical durability or economic feasibility throughout the life cycle. This review provides an integrated synthesis of sustainable asphalt mixtures by jointly examining recycling strategies, temperature-reduction processes (warm-mix, half-warm-mix, and cold-mix asphalt technologies), and their combined applications through an integrated performance–cost–environment perspective. The literature reveals substantial methodological fragmentation, with limited harmonisation of functional units, system boundaries, and allocation rules, which constrains cross-study comparability. Evidence indicates that reclaimed asphalt, recycled concrete aggregates, and steel slag can maintain or improve rutting resistance, stiffness, and moisture durability while enabling material cost savings of approximately 5–68%. Temperature-reduction technologies further achieve significant energy and GHG reductions in the production phase (20–70%), with integrated recycling–temperature-reduction systems showing the most consistent combined benefits. Overall, this review demonstrates that asphalt sustainability cannot be established through single-dimensional assessments but requires harmonised life-cycle frameworks that explicitly link environmental gains to mechanical performance, durability, and economic viability. Full article

Comparing cold-recycled asphalt mixtures (CRAMs) to conventional hot-mix asphalt (HMA) shows that CRAMs offer several logistical, financial, and environmental advantages. However, such CRAMs, when using asphalt emulsion, still suffer from excessive water damage and poor early-age performance. The main aim of this study is to improve CRAMs by incorporating two biomass ashes and reclaimed asphalt pavement (RAP): palm leaf ash (PLA) and reed ash (RA) with different percentages of RAP. RAP was used in five percentage levels, 0%, 25%, 50%, 75%, and 100% by weight of mix, to develop the CRAMs. In addition, the improvement in CMA mechanical properties was assessed by incorporating PLA as filler replacement in five percentages, namely: 0%, 1.75%, 3.5%, 5.25%, and 7% by weight of aggregate. RA was used as an activator at 0.25%, 0.5, 1%, and 2% by weight of aggregate. The moisture susceptibility test, Indirect Tensile Strength Test (ITS), and Marshall test were used to assess the mechanical properties. The results obtained showed that the durability and mechanical properties of CMA are effectively enhanced with the addition of 1.5% PLA, 0.45% RA, and 5.5% Ordinary Portland Cement (OPC) as fillers. In addition, CRAMs with a higher percentage of RAP 75%, showed higher strength in terms of Marshall stability. These findings demonstrate that the studied CRAMs offer a reliable alternative for pavement applications, namely when sustainable and cost-effective materials are required. Full article

Freeze–thaw damage significantly reduces the performance and durability of airport pavements in cold regions. Traditional assessment methods, such as the F300 freeze–thaw test, are time-consuming and hinder rapid optimisation of mix design. In addition, previous studies have mostly relied on long-term laboratory testing and have evaluated phase-change concrete (PCC) independently, without considering synergistic effects. These approaches lack fast, synergy-aware predictive capability and interpretable tools for mix proportion design, resulting in a gap between laboratory research and practical engineering applications. To address this issue, this study proposes an intelligent and explainable framework for predicting freeze–thaw damage and guiding mix design of steel fibre-reinforced phase-change concrete (SF–PCC). A boundary-controlled experimental programme was first conducted, varying steel fibre (SF) content from 0 to 1.2% and phase-change material (PCM) content from 0 to 12% under fixed mixture conditions. The freeze–thaw test results were recorded sequentially and used to construct a supervised learning dataset. Then, an XGBoost model was developed to predict two key durability indicators: relative dynamic modulus of elasticity (RDEM) and mass loss. SHAP (SHapley Additive exPlanations) analysis was further applied to quantify feature importance and interaction effects. The model achieved high predictive accuracy (R² = 0.9938 for mass loss and R² = 0.9935 for RDEM) under controlled experimental conditions. After 300 freeze–thaw cycles, the reference mix exhibited an RDEM of 61.2%, while optimised configurations showed improved performance. The economical design (9% PCM + 0.9% SF) achieved an RDEM of 66.8%, and the high-performance design (12% PCM + 1.2% SF) reached 72.6%. These results demonstrate that the proposed framework can effectively enhance durability and support rapid preliminary decision-making. The framework significantly accelerates freeze–thaw performance evaluation by enabling near-instant prediction and serves as an efficient supplementary tool for mix design optimisation alongside conventional laboratory testing. It also provides interpretable, data-driven insights for the design of freeze–thaw-resistant airport pavement concrete in cold regions. Full article

Pavement engineers frequently need a rapid and accurate evaluation of layer thicknesses and conditions. Such an assessment is critical for evaluating current conditions and identifying optimal maintenance and rehabilitation needs. The objective of this study was to use remote sensing for assessing pavement thickness uniformity. For this purpose, the potential use of Ground-Penetrating Radar (GPR) data was considered. Traditional GPR data interpretation methods are generally not intended to quantify the spatial variability information required for pavement management-related analyses. Thus, the method presented herein is based on several layers of statistical assessment of pavement thickness changes for identifying homogeneous sections. The suggested approach provides consistent thickness assessment over consecutive pavement segment lengths. Such evaluation is particularly useful for integration into Pavement Management System (PMS) analyses at both the project and network levels. The approach was used in concrete pavements, and data from an in-service roadway are provided as an example to demonstrate how this analysis is applied. This analysis approach provides several benefits to highway agencies: a quick and accurate condition assessment regarding existing pavement thickness; better decision-making in identifying alternative maintenance and rehabilitation techniques for uniform sections with respect to thickness, which clearly need to be combined with condition assessment of pavement layer materials; and efficient use of remote sensing data for pavement sections where construction inventory data may not be available. Full article

Noise in long highway tunnels and underground interchanges poses a significant environmental concern, affecting both drivers and nearby residents. This research develops an acoustic finite element model of a long tunnel in Leuven Measurement Systems (LMS) Virtual Lab to characterize the tunnel noise field, and the effectiveness of different noise mitigation measures was also evaluated and optimized accordingly. The model is validated against in situ monitoring data, with deviations controlled within 3 dB(A) and strong agreement confirmed by the Kappa consistency test. Both simulations and measurements show that sound pressure levels (SPLs) are generally highest near the tunnel center and lower toward the portal, exhibiting periodic fluctuations rather than a monotonic decrease. The dominant noise energy is concentrated between 125 Hz and 500 Hz. SPLs at 1.8 m above the road surface are noticeably higher than at 1.2 m and 1.5 m, indicating greater noise exposure for drivers of large vehicles compared with smaller vehicles. Noise reduction performance is further assessed for different lining materials and pavement types. Installing sound-absorbing panels in the tunnel midsection provides effective attenuation, with expanded perlite panels, single-layer metal micro-perforated panels, and FC quiet perforated panels (FC-PP) performing best, while porous asphalt shows superior noise reduction compared with conventional dense-graded asphalt pavements. Full article

Urban districts are increasingly exposed to overlapping heat stress and stormwater loads driven by warming trends, more intense rainfall, and continued growth of impervious surfaces. Pavements occupy a large share of the public right-of-way, so their material and structural design offers a scalable pathway for urban climate adaptation. Yet the literature on porous asphalt remains fragmented, with hydrological performance often assessed using infiltration or permeability metrics in isolation, while thermal studies frequently report surface cooling without consistently tracking the governing water budget or its persistence. To reconcile these disconnected strands, this review synthesizes a conceptual hydro-thermal balance framework in which runoff mitigation and heat moderation are treated as a coupled problem controlled by storage, drainage pathways, and evaporative demand. Within this framing, cooling is primarily water-limited: permeability enables wetting and redistribution, but the magnitude and duration of temperature reduction depend on how much water is retained near the surface and how long it remains available for evaporation, rather than on permeability alone. The review integrates the current understanding of mixture structure and pore connectivity, permeability–storage behavior, moisture availability and evaporation, and the operational factors that govern performance persistence. Laboratory and field evaluation approaches are summarized alongside modeling methods used to interpret coupled hydro-thermal responses under different climates. Practical constraints—including clogging, maintenance requirements, and durability risks under repeated moisture–temperature cycling—are discussed as mechanisms that can progressively suppress both infiltration and water availability, undermining long-term function without performance-based specifications and life-cycle planning. Finally, design and policy implications are outlined for integrating porous asphalt into coordinated heat-and-stormwater strategies, and research priorities are identified to advance standardization, long-term monitoring, and coupled hydro-thermal–mechanical assessment. Full article