Search Results (45)

The escalating demand for sustainable and eco-friendly production processes has necessitated the exploration of renewable resources for the synthesis of valuable chemicals. This study investigated the fermentative synthesis of gluconic acid (GA) and xylonic acid (XA) from hydrolyzed palm fronds by using Gluconobacter oxydans. The key variables examined included agitation speed, inoculum ratio, and composition of fermentation media. In a synthetic medium, maximum GA concentration reached 52.82 ± 12.88 g/L at 65 h using 150 rpm agitation and 15% (v/v) inoculation, while maximum XA concentration achieved 2.31 ± 1.43 g/L at 96 h using 220 rpm agitation and 9% (v/v) inoculation. In the hydrolysate medium, the maximum GA concentration was 3.24 ± 0.66 g/L at fermentation onset using 220 rpm agitation and 15% (v/v) inoculation, while the maximum XA concentration reached 0.62 ± 0.04 g/L at 24 h using 190 rpm agitation and 5% (v/v) inoculation. These findings demonstrate the feasibility of utilizing palm fronds as a renewable feedstock for the sustainable synthesis of high-value biochemicals, promoting waste valorization, and contributing to the advancement of a circular bioeconomy. Full article

Identifying sustainable and efficient methods for the degradation of plastic waste in landfills is critical for the implementation of the Saudi Green Initiative, the European Union’s Strategic Plan, and the 2030 United Nations Action Plan, all of which are aimed at achieving a sustainable environment. This study assesses the influence of palm fronds (PFR) on the thermal degradation of polypropylene plastic (PP) using TGA/FTIR experimental measurements, thermo-kinetics, and machine learning convolutional deep learning neural networks (CDNN). Thermal degradation operations were conducted on pure materials (PFR and PP) as well as mixed (blended) materials containing 25% and 50% PFR, across degradation temperatures ranging from 25 to 600 °C and heating rates of 10, 20, and 40 °C·min⁻¹. The TGA data indicated a synergistic interaction between the agricultural waste (PFR) and PP plastic, with decreased thermal stability at temperatures below 500 °C, attributed to the hemicellulose and cellulose present in the PFR biomass. In contrast, at temperatures exceeding 500 °C, the presence of lignin retards the degradation of the PFR biomass and blends. Activation energy values between 81.92 and 299.34 kJ·mol⁻¹ were obtained through the application of the Flynn–Wall–Ozawa (FWO) and Kissinger–Akahira–Sunose (KAS) model-free methods. The application of CDNN facilitated the extraction of significant features and labels, which were crucial for enhancing modeling accuracy and convergence. This modeling and simulation approach reduced the overall cost function from 41.68 to 0.27, utilizing seven hidden neurons, and 673,910 epochs in 13.28 h. This method effectively bridged the gap between modeling and experimental data, achieving an R² value of approximately 0.992, and identified sample composition as the most critical parameter influencing the thermolysis process. It is hoped that such findings may facilitate an energy-efficient pathway necessary for the thermal decomposition of plastic materials in landfills. Full article

Mining activities often contaminate soils with heavy metals, generating environmental and health risks. This study investigates the ecotoxicity of muddy (Mw) and sandy (Sw) mining wastes on Phaseolus vulgaris and assesses the impact of five locally sourced biochar amendments on plant growth and soil pore water (SPW) properties. Most biochars improved water retention, except for argan nut shells (An) biochar, highlighting the importance of feedstock type. Sw supported better plant growth than Mw regardless of biochar addition, due to textural differences. Palm fronds (Pf) biochar significantly enhanced surface leaf area in Sw. SPW analysis revealed that biochar affected pH and electrical conductivity (EC) differently across soil types. Mw consistently increased pH, while Sw’s pH was biochar-dependent. A significant 5.1-fold EC increase was recorded in Sw amended with Pf. All biochars reduced Pb availability in Mw at planting, while Cu availability decreased in Sw at harvest. In Mw, Pb, Zn, and Cu, uptake and accumulation were unaffected by biochar, while a slight reduction was observed in Sw roots. A germination test with Lepidium sativum confirmed these findings, particularly the inhibition observed with An. This dual approach highlights the toxicity of mining soils and biochars’ potential as amendments for soil remediation programs. Full article

Renewable energy sources are becoming increasingly crucial in the global energy industry and are acknowledged as a significant substitute for fossil fuels. Oil palm fronds are a type of biomass fuel that can be utilized as a substitute for fossil fuels in the combustion process of boilers. Co-firing (HT-FRD) is a beneficial technology for reducing exhaust gas emissions generated by coal-burning power stations. By utilizing computational fluid dynamics (CFD), this study has modeled and evaluated co-firing palm frond residue (HT-FRD) with hydrothermal treatment into a 315 MWe boiler. In the simulation, six different HT-FRD co-firing ratios, 0%, 5%, 15%, 25%, 35%, and 50%, were used to demonstrate the differences in combustion characteristics and emissions in the combustion chamber. The data indicate that HT-FRD co-firing can enhance temperature distribution, velocity, and unburned particles. All in all, co-firing conditions with 5–15% HT-FRD ratios appear to have the most favorable combustion temperature, velocity, and exhaust gas characteristics. Full article

This paper investigates, experimentally and numerically, the shear strengthening of Normal Concrete (NC) beams using post-tensioning steel bars and Engineered Cementitious Composite (ECC) reinforced with chemically cured Palm Fronds (PFs). The benefits of strain-hardening ECC and the tensile strength of PFs cured with 6% wt Alkali NaOH solution beside post-tensioned bars have been employed herein. Seven full-scale Reinforced Concrete (RC) beams were fabricated and experimented with under three-point loading until failure. The test parameters include the strengthening technique, type, and configuration of the material used for strengthening. The strengthening process has been implemented through two techniques: Externally Bonded Reinforcement (EBR) and Near-Surface Mounted (NSM) Reinforcement. The strengthening materials have been configured and placed in horizontal, vertical, and inclined positions. The effectiveness of the strengthening methods has been evaluated by examining their cracking propagations, load-deflection responses, collapse modes, elastic stiffness, and absorbed energy. It was found that the proposed strengthening systems could significantly control the crack pattern and failure mode, and they could enhance the ultimate load amplitude up to 37% and 50% for NSM ECC with PFs and EBR post-tensioning steel bars, respectively. Nonlinear three-dimensional finite element models of the tested beams were developed and validated with the test data, where it was found that finite element models predict the structural performance of tested beams with a maximum error of only 2%. Full article

Designers actively pursue the use of novel materials and concepts in furniture and interior design. By providing insights into their processing behavior and suitability for 3D-printing processes, this research helps to highlight the potential of using waste materials to create more environmentally friendly and sustainable 3D-printing filaments that can be used in furniture and interior design. Furthermore, the study evaluates the effect of incorporating palm midrib nanoparticles (DPFNPs) to reinforce a high-density polyethylene (HDPE) matrix with different loadings such as 10, 20, 30, 40, and 50 wt.%. The composites were extruded into filaments using a manual extruder, which was then utilized to fabricate 3D-printed specimens using a 3D-printing pen. The effect of adding DPFNPs on the composite’s chemical, thermal, and mechanical properties was evaluated, with a particular focus on how these modifications influence the melt flow rate (MFR) and, subsequently, the material’s printability. The results revealed that HDPE and filament composites presented similar FTIR spectra. On the other hand, the filament composites presented an increase in the thermal stability and a decrease in the mechanical strength with increasing DPFNP content in the HDPE matrix. The filaments were successfully printed using a 3D-printing pen. Thus, using DPFNPs in the HDPE matrix presents a low-cost alternative for filament production and may expand 3D-printing applications in interior and furniture design with more sustainable materials. Future work will delve into optimizing these composites for improved printability and assessing their recyclability, aiming to broaden their applications in 3D printing and beyond. Full article

This study presents novel life cycle assessment (LCA) findings on hydrochar production from Saudi-Arabia-based date palm fronds biomass waste using hydrothermal carbonization (HTC). The LCA procedure incorporated normalization, weighting, and improvement assessment. The system boundary encompassed water consumption and energy requirements within a lab setting representing a gate-to-gate process. The OpenLCA 1.11.0 software with the European Life Cycle Database 3.2 (ELCD 3.2) was utilized for the study and we employed the ReCiPe Midpoint (H) 2016 and Environmental Footprint 3.0 (EF 3.0) impact assessment methods. The results indicated that fossil fuel usage represented the most significant impact category with the HTC and drying processes identified as major contributors. It was also observed that the HTC process exerted far greater detrimental impacts on the environment than the biomass grinding process. The overwhelming impact of fossil fuel resources could be mitigated by optimizing the batches of biomass or hydrochar samples in each operation, which could alleviate fossil fuel consumption by up to 94%. The findings emphasize the need for targeted interventions to mitigate the environmental burden and contribute to sustainable hydrochar production. Full article

Biodesulfurization using biotrickling filters (BTFs) under anoxic conditions is a cost-effective method for biogas clean-up. To improve the performance of BTFs, the microbial consortia from the anaerobic pond of a swine farm (SW), the denitrification pond of a tuna factory (DN), and the UASB of the concentrated latex industry (LW) were immobilized on BTFs. In this study, the efficiency of BTFs immobilized with the microbial consortia for the reduction of H₂S gas combined with the reduction of nitrate contained in wastewater was investigated. The results showed that H₂S was completely removed at the inlet H₂S concentration of 207.8–1476 ppmv with wastewater circulation under anoxic conditions. However, only the DN-BTF achieved H₂S removal of 95.2% at an inlet concentration of 2500 ppmv. An increase in the N/S ratio (0.356–2.07 mol/mol) improved the H₂S removal of the SW-BTF, LW-BTF, and DN-BTF but not the BTF-C. Moreover, the DN-BTF had the highest nitrate removal rate (71.1%) with an N/S ratio of 2.07 mol/mol. When oxygen was supplied in wastewater at DO = 3.60 ± 0.41 mg/L, sulfate was generated at a higher rate, but nitrite production was lower than at DO~0. After microbial community analysis, Proteobacteria were the main phyla involved in the biodesulfurization process. Full article

Water pollution with dye effluents from different industries is a broadly established environmental and health problem that needs serious attention. In this study, making use of Acacia nilotica seed extract, greenly synthesized MnO₂ nanoparticles were loaded on the surface of biochar derived from palm waste (MnO₂/PF), with specific surface areas of 70.97 m²/g. Batch experiments were adopted, aiming to evaluate the performance of palm fronds, biochar, and the MnO₂/PF adsorbents in methyl orange (MO) removal from an aqueous solution. The feedstock and synthesized biochars were comprehensively characterized using XRD, SEM-EDX, FTIR, and BET surface area techniques. Moreover, the influences of the modification of palm fronds, initial dye concentrations, pH, and adsorbent dosage on MO uptake were examined. The results demonstrated that MnO₂/PF biochar nanocomposite led to an increase in the removal efficiency by 6 and 1.5 times more than those of palm fronds and biochar, respectively. In addition, it was found that the second-order kinetic model presented the kinetic adsorption very well. This paper demonstrates that the depositing of greenly synthesized MnO₂ nanoparticles on the date palm waste biochar forms a novel adsorbent (MnO₂/PF) for the removal of MO from aqueous solutions. Furthermore, this adsorbent was easy to synthesize under moderate conditions without the need for chemical capping agents, and would thus be cost-effective and eco-friendly. Full article

The present study deals with the sound absorption performance of natural fibres from the oil palm frond (OPF), mainly considered agricultural waste. Therefore, this study aimed to investigate the sound absorption performance of OPF fibre-reinforced composite under normal incidence sound. The materials used were OPF particles and urea-formaldehyde was used as an adhesive. The particleboards were produced with three particle sizes and four target densities. The absorption coefficient of normal incidence sound (α_n) was tested using an impedance tube. The effects of particle size and bulk density were also evaluated. The findings reveal thatα_n exceeded 0.45 at 1000 Hz and could reach 0.95 above 3.3 kHz. This occurred when the bulk density of the OPF composite particleboards ranged between 0.3–0.4 g/cm³, and the particle size varied between medium to coarse. The results also indicated that the absorption frequency and the degree of α_n significantly increased as the bulk density decreased. Therefore, OPF fibres can be used to create sound-absorbing composite particleboards. Full article

Green roofs contribute to more sustainable cities, but current commercial substrates suffer from important limitations. If carefully selected, biochar could serve as a viable option for a more sustainable green roof substrate. We propose a protocol to select an optimal biochar for green roof substrate amendment. Coffee husks, medium-density fiberboard, palm date fronds, and a mixture of waste wood, tree bark, and olive stone kernels are selected as residues for biochar production to develop a selection protocol. The residues are pyrolyzed at 350, 450, 500, and 550 °C in a lab-scale reactor. A pyrolysis temperature of 450 °C is selected for upscaling and is based on biochar yield, pH, salinity, and elemental composition. From evaluating the biochar characteristics after upscaling, it can be concluded that the biochar’s carbonization degree is mainly controlled by pyrolysis temperature, while yield, pH, and salinity are more dependent on the biomass properties. Ultimately, our procedure evaluates the presence of important contaminants, the biochar’s water holding capacity, salinity, pH, and carbonization degree. To validate the developed protocol, plant coverage experiments on green roofs are performed, which are quantified using a novel digital image processing method, demonstrating its efficient use to facilitate future biochar selection in substrates. Full article

Novel biosensors based on carboxymethyl cellulose extract from date palm fronds containing Ag nanoparticles as an electrochemical working electrode for fast hydroxymethylfurfural (HMF) sensing in date molasses were prepared. The morphological, structural, and crystallinity characteristics of the prepared Ag@CMC were described via SEM, DLS, TEM, and XRD. In addition, Raman spectroscopy and UV–VIS spectroscopy were performed, and thermal stability was studied. The investigated techniques indicated the successful incorporation of AgNPs into the CMC polymer. The sensing behavior of the prepared AgNPs@CMC electrode was studied in terms of cyclic voltammetry and linear scan voltammetry at different HMF concentrations. The results indicated high performance of the designed AgNPs@CMC, which was confirmed by the linear behavior of the relationship between the cathodic current and HMF content. Besides, real commercial samples were investigated using the novel AgNPs@CMC electrode. Full article

Local knowledge of a region is an asset that encourages the identification of a region. Hence, the specificity, uniqueness, and character that animates a particular city can distinguish it significantly from other cities. Sago tree fronds are widely applied to buildings as an alternative material for making tiles for roofs and other parts of buildings. The sago palm has long been used for making roofs and walls, especially in traditional houses. Few previous studies have used sago fronds as a manufacturing material for traditional houses. However, based on data in the field, many traditional houses still use sago fronds as a roof and wall framing material. This is also an effort to overcome the urban heat island phenomenon (UHI) in buildings. The UHI phenomenon is a phenomenon of urban development that highly affects environmental quality conditions and causes microclimate changes where air temperature conditions in urban areas are higher than the surrounding air temperatures. Sago midrib fiber is a natural composite material used as a reinforcing material for natural composite materials due to its thermal and mechanical properties. Composite materials using the hand lay-up technique—with characterization methods including the impact test and the DSC test, variations in $NaOH$ levels, and variations in the resin–catalyst matrix—were used in this study. The results obtained were then compared with those in the literature. The results showed that 6% $NaOH$ obtained the most significant impact value of 2.1 $J$, and the resin–catalyst matrix variation of 97.5%:2.5% obtained the most significant impact value, which was 2.4 $J$. Meanwhile, the DSC test results showed that the material’s best value for retaining heat was at 4% $NaOH$ content variation and a resin–catalyst matrix variation of 97.5%:2.5%. Full article

Oil palm frond as an abundant and inexpensive lignocellulosic waste was used to optimize alkaline pretreatment for ethanol production. The studied lignocellulosic waste is one of the largest biomasses (47%) in oil palm waste. Oil palm frond fibers were processed by steam explosion, hot water extraction, and alkaline extraction pretreatment, followed by simultaneous saccharification and fermentation (SSF), for ethanol production as an alternative energy resource. To optimize alkaline extraction for oil palm frond, a Taguchi method with a three-factor design constituted a concentration of NaOH (15%, 20%, and 25%), time (30, 60, and 90 min), and temperature (70, 80, and 90 °C). An optimum alkaline extraction condition of 15% NaOH at 90 °C for 60 min gave the highest percentage of α-cellulose (80.74%) and the lowest percentages of lignin (15.99%), ash (1.05%), and pentosan (2.09%). In addition, the optimized pretreatment condition significantly improved α-cellulose to 52.65% and removed lignin up to 51.78%. Simultaneous saccharification and fermentation (SSF) was carried out with 10% (dry weight) alkaline pretreated OPF fibers, Celluclast 1.5 L (15 FU/gram substrate), Novozyme 188 (15 IU/gram substrate), and Saccharomyces cerevisiae SC90 at 40 and 45 °C. The highest ethanol concentration, theoretical ethanol yield, and ethanol productivity observed at 40 °C were 33.15 g/L, 72.54%, and 0.55 g/L/h, respectively. The results suggest that an optimized alkaline pretreatment process using palm frond as a lignocellulosic waste is a sustainable approach to produce efficient ethanol production. Full article

The oyster mushroom (Pleurotus species) is a popular and widely cultivated edible mushroom that can be found worldwide, including in Malaysia. However, its local production is unable to fulfil the market demand, partly due to the limited availability of rubber wood sawdust (RWS) as the conventional cultivation substrate. Furthermore, the palm oil industry in Malaysia generates large volumes of organic by-products that have caused environmental concerns. Therefore, the potential utilisation of oil palm waste-based substrates in order to develop a substitute RWS for Pleurotus ostreatus mushroom production is evaluated in this study, based on their agronomic performance and nutritional properties. Empty fruit bunches (EFBs), oil palm fronds (OPFs), and oil palm trunks (OPTs) were used to formulate the substrates. The control used was 100% RWS. Generally, 100% EFB showed a better agronomic performance, and mushroom growth was 1.9 times faster compared to the control, with a comparable mushroom yield. The crude protein and beta glucan content of mushrooms grown on oil palm by-product-formulated substrates were significantly higher than those grown using the control. Additionally, the number of fruiting bodies, crude protein, and beta glucan content of the mushrooms were positively correlated with potassium in the substrate. Therefore, 100% EFB could be used as a potential substitute for RWS for the cultivation and production of P. ostreatus. Full article