Search Results (36)

Pillarless mining technology is of great significance for improving coal recovery rates, but the intense mining-induced stress disturbances on gob-side entries often lead to surrounding rock instability. In this study, we focused on the ground control challenges in the headgate of Panel 81308 at Huayang Mine No. 2. Comprehensive monitoring of roof–floor convergence, rib deformation, and support resistance revealed the gob-side entry retaining deformation mechanisms with roof-cutting pressure relief; the results show that this retaining deformation exhibits the following three phases of characteristics: the rapid, decelerated, and stable stages. The average roof–floor convergence (607 mm) was significantly greater than the average rib deformation (170 mm), with floor heave accounting for 72.6% of total convergence. The coal pillar side showed dominant deformation in rib movements. The mining influence zones can be divided, based on their distances behind the working face, into strong disturbance zones (0–88 m), weak disturbance zones (88–142 m), and stabilized zones (>178 m). The cable bolt support system demonstrated advanced response characteristics. Compared with conventional gob-side entry retaining, the roof-cutting pressure relief technique altered stress transmission paths, significantly reduced roof load transfer efficiency, and effectively controlled roadway convergence, providing technical guidance for safe production in both this panel and mines with similar geological conditions. Full article

The mechanical properties of grouting materials and their cured grouts significantly impact the reinforcement effectiveness in deep coal mine roadways. This study employed shear rheology tests of slurry, structural tests, NMR (nuclear magnetic resonance), and uniaxial compression tests to comparatively analyze the mechanical characteristics of a composite cement-based grouting material (HGC), ordinary Portland cement (OPC), and sulfated aluminum cement (SAC) slurry and their cured grouts. The HGC (High-performance Grouting Composite) slurry is formulated with 15.75% sulfated aluminum cement (SAC), 54.25% ordinary Portland cement (OPC), 10% fly ash, and 20% mineral powder, achieving a water/cement ratio of 0.26. The results indicate that HGC slurry more closely follows power-law flow characteristics, while OPC and SAC slurries fit better with the Bingham model. The structural recovery time for HGC slurry after high-strain disturbances is 52 s, significantly lower than the 312 s for OPC and 121 s for SAC, indicating that HGC can quickly produce hydration products that re-bond the flocculated structure. NMR T2 spectra show that HGC cured grouts have the lowest porosity, predominantly featuring inter-nanopores, whereas OPC and SAC have more super-nanopores. Uniaxial compression tests show that the uniaxial compressive strength of HGC, SAC, and OPC samples at various curing ages gradually decreases. Compared to traditional cementitious materials, HGC exhibits a rapid increase in uniaxial compressive strength within the first seven days, with an increase rate of approximately 77.97%. Finally, the relationship between micropore distribution and strength is analyzed, and the micro-mechanisms underlying the strength differences of different grouting materials are discussed. This study aids in developing a comparative analysis system of mechanical properties for deep surrounding rock grouting materials, providing a reference for selecting grouting materials for various engineering fractured rock masses. Full article

Land reclamation is crucial for restoring ecosystems in mining areas, improving land use efficiency, and promoting sustainable regional development. Traditional single-indicator assessments fail to capture the full complexity of reclamation, highlighting the need for a more comprehensive evaluation approach. This study combines field-measured and remote sensing data to develop multiple evaluation indices, creating a comprehensive framework to assess reclamation effectiveness. A soil quality index based on the Minimum Data Set (SQI_MDS) was developed to analyze spatial variations in soil quality, efficiently capturing key soil attributes. Remote sensing data were used to calculate the Dump Reclamation Disturbance Index (DRDI) and the Enhanced Coal Dust Index (E_CDI) to evaluate vegetation recovery and ecological improvements. The Comprehensive Evaluation Quality Index (CEQI) was introduced, synthesizing soil, vegetation, and ecological conditions for a holistic assessment. Key findings include significant soil quality improvement over time, with MDS effectively capturing variations; vegetation recovery increased with reclamation duration, though regional disparities were observed; ecological conditions steadily improved, as evidenced by a decline in ECDI values and reduced contamination; and the CEQI reflected overall improvements in reclamation effectiveness. This study offers a practical framework for coal mining land reclamation, providing scientific support for decision-making and guiding effective reclamation strategies for ecological restoration and sustainable land management. Full article

Mining significantly impacts terrestrial ecosystems despite its importance to the global economy. As part of soil ecosystems, fungi are highly responsive to environmental and human-induced drivers, shifting community composition and structure. Indeed, fungi play a key role in maintaining ecosystem resilience. Thus, we aim to address the question of whether soil fungal communities maintain similar ecological functions despite changes in community composition due to the impact of mining across ecosystems. To evaluate the ecological role of fungi across four ecosystems with varying iron mining impact levels, we used the FUNGuild database to assign functional guilds at the genus level. Co-occurrence network and ordination analyses were used to infer ecological relationships among fungal taxa and visualize the correlation between edaphic properties and fungal communities. A total of 22 functional guilds were identified, with dung saprotrophs, wood saprotrophs, fungal parasites, plant pathogens, ectomycorrhizal fungi, animal pathogens, and endophytes being the most abundant. Soil properties such as pH, organic matter, texture, and nutrients drive taxonomic and functional shifts. Our findings indicate that while mining activities shift fungal community compositions across ecosystems, the profiles of functional guilds show overlap between highly, moderately, and lowly impacted ecosystems, indicating functional redundancy. Network analysis reveals that highly connected hub taxa contribute to ecological redundancy across ecosystems and might act as a buffer against environmental disturbances. Our findings emphasize the important ecological role of soil fungi and indicate a potential for using fungal communities as bioindicators of ecological recovery in post-mining landscapes. From a mining and restoration perspective, this offers a low-cost, ecologically meaningful tool for monitoring soil recovery and guiding reclamation efforts. Full article

This study investigates the traditional coal pillar support methods employed in double-roadway excavation of high-mining-height longwall faces, specifically those with widths ranging from 20 m to 30 m. It highlights that these methods not only result in substantial coal pillar loss and low recovery rates but also create conditions for stress concentration due to inadequate dimensions, thereby increasing the risk of accidents. Based on the engineering context of the Jinjitan Coal Mine’s 113 and 111 working faces, this paper optimizes coal pillar dimensions through theoretical calculations and Flac3D numerical simulations, with the results indicating that the optimal coal pillar width is 12 m. Analysis of a 12 m inter-roadway coal pillar focuses on the bearing characteristics of auxiliary transport roadways and coal transportation roadways. Five different reinforcement schemes are examined, including (no support, conventional anchor reinforcement, presser anchor cable through reinforcement, constant-resistance large-deformation anchor cable through reinforcement, and a combination of presser with negative Poisson’s ratio (NPR) constant-resistance large-deformation anchor cable support). The findings reveal that in the investigation of the reinforcement mechanism for the 12 m wide coal pillar, employing NPR constant-resistance large-deformation anchor cables alongside presser anchor cables effectively mitigates the compression deformation caused by dynamic loading disturbances from the overlying rock layers. This approach not only dissipates energy but also transforms the coal pillar from a biaxial stress state to a triaxial stress state. The reinforcement scheme successfully reduces the peak stress of the coal pillar from 68.5 MPa to 35.3 MPa, significantly enhancing both the peak strength and residual strength of the coal pillar, thereby ensuring the stability of the inter-roadway coal pillar and the safe recovery of the working face. Full article

The plumes generated during the collection of polymetallic nodules in the deep sea may have a significant impact on the marine ecosystem. Therefore, this article reviews the progress in deep-sea mining and monitoring technologies related to plumes. It is suggested that specific areas of environmental interest (APEIs) and positive altitude characteristic regions (such as seamounts and hills) in the process of polymetallic nodule collection can serve as refuges for benthic organisms and provide a biological basis for the recovery of biodiversity in mining areas. Water-supported vessels, pipeline lifting systems, and hydraulic collection methods are the least disruptive and most promising methods. By sorting out the deep-sea mining process, plumes can be roughly classified into seabed disturbance plumes and tailing plumes. The best way to address plume formation is at the source when developing environmentally friendly mining vehicles. The evaluation of plumes is crucial for the sustainable development of the environment and seabed resources. However, the mechanism is not clear at present. Therefore, laboratory simulation and in situ monitoring need to be coordinated, and attention should be paid to the impact on benthic marine organisms as much as possible during original operations. Plume research in the deep-sea mining process will also provide favorable support for the possible future development of seabed resources. Full article

Coal mining has a certain influence on and causes disturbances in groundwater. To investigate the variation trend of groundwater around the open-pit mine in grassland area, taking Shengli No. 1 open-pit mine as an example, the impact and variation trend of groundwater level in Quaternary aquifer around the mine area was studied by using the data of hydrological monitoring wells. The results show that the water level around the mining area varies from one year to the next. Since 2008, the water level has experienced a process of reduction, stability and increase. Compared with the background water level value, the current water level of each monitoring well is lower than the background water level. The influence radius calculated by Kusakin formula ranges from 94.15 m to 906.80 m, and the aquifer is heterogeneous. On the basis of the correlations between changes in waterline in monitoring wells and the stope distance, the disturbance radius of open-pit mining on surrounding diving water in grassland area is less than 2000 m. Based on the comprehensive analysis of the alteration of diving waterline and its influencing factors, the main factors affecting the variation in the phreatic water level are atmospheric precipitation, evaporation, groundwater usage and dewatering water. All factors act on the diversification of diving water level synthetically. The internal waste dump of an open-pit mine has a positive effect on the surrounding groundwater recovery. The aim of this study is to reveal the impact of open-pit mining on surrounding groundwater and providing scientific basis for future mining in other open-pit mines. Full article

In the discussion about sustainable forestry, a key role is played by the development of ecosystem services, including ecological, social, and economic ones, in which biodiversity and carbon (C) sequestration are among the most important. Afforestation of disturbed and post-mining sites is one of the ways to minimize the negative impact of civilization on the environment. Optimizing C sequestration strategies at post-mining sites plays a crucial role in promoting ecosystem recovery, supporting climate change mitigation, and enabling C offsetting. In this study, we compared the C storage in the soil and plant biomass of forest ecosystems developed on coal-mine heaps for different scenarios of reclamation and succession. We tested combinations of sites (i.e., non-reclaimed sites on bare carboniferous rock [BR] and sites reclaimed by applying topsoil [TS]) and successional woodland and tree plantation. The estimated potential for total C storage (in the soil + biomass) for TS sites ranged from 68.13 to 121.08 Mg ha⁻¹, of which 52.20–102.89 Mg ha⁻¹ was stored in the soil and 12.09–20.15 Mg ha⁻¹ in the biomass. In the non-reclaimed sites on BR, the total C storage was much higher, amounting to 523.14 Mg ha⁻¹ (507.66 Mg ha⁻¹ being in the soil), which was due to the geogenic coal content in the BR. However, the C storage in the biomass (15.48 Mg ha⁻¹) and litter (5.91 Mg ha⁻¹) was similar to the amounts obtained from the reclaimed sites. The number of species did not differ statistically significantly between the analyzed variants. On average, 14 species were recorded in the plots. The average Shannon–Wiener index (H’) value was higher for sites with BR (1.99) than TS variants on reclaimed plots (1.71). The lowest H’ value was for those plots with Robinia pseudacacia in the stand. One of the main implications of the obtained results for sustainable forestry is the perspective of using succession in the recovery of a disturbed ecosystem. We noted that woodlands from succession on BR are highly biodiverse, have high C sequestration potential, and do not require time-consuming reclamation treatments. Full article

Artisanal small-scale mines (ASMs) in the Amazon Rainforest are an important cause of deforestation, forest degradation, biodiversity loss, sedimentation in rivers, and mercury emissions. Satellite image data are widely used in environmental decision-making to monitor changes in the land surface, but ASMs are difficult to map from space. ASMs are small, irregularly shaped, unevenly distributed, and confused (spectrally) with other land clearance types. To address this issue, we developed a reliable and efficient ASM detection method for the Tapajós River Basin of Brazil—an important gold mining region of the Amazon Rainforest. We enhanced detection in three key ways. First, we used the time-series segmentation (LandTrendr) Google Earth Engine (GEE) Application Programming Interface to map the pixel-wise trajectory of natural vegetation disturbance and recovery on an annual basis with a 2000 to 2019 Landsat image time series. Second, we segmented 26 textural features in addition to 5 spectral features to account for the high spatial heterogeneity in ASM pixels. Third, we trained and tested a Random Forest model to detect ASMs after eliminating irrelevant and redundant features with the Variable Selection Using Random Forests “ensemble of ensembles” technique. The out-of-bag error and overall accuracy of the final Random Forest was 3.73 and 92.6%, which are comparable to studies mapping large industrial mines with the normalized difference vegetation index (NDVI) and LandTrendr. The most important feature in our study was NDVI, followed by textural features in the near and shortwave infrared. Our work paves the way for future ASM regulation through large area monitoring from space with free and open-source GEE and operational satellites. Studies with sufficient computational resources can improve ASM monitoring with advanced sensors consisting of spectral narrow bands (Sentinel-2, Environmental Mapping and Analysis Program, PRecursore IperSpettrale della Missione Applicativa) and deep learning. Full article

To study the influence of coal mining on the water richness overlying strata in the mining area using time-lapse electrical monitoring technology, four dataset acquisitions were completed with the same acquisition method, equipment, parameters, and processing flow. According to the characteristics of the data, major problems such as topographic correction, high-precision denoising, spatial and temporal normalization, and resistivity data inversion have been solved. Precise tomographic imaging was achieved through high-precision data processing and difference inversion. The results show that the electrical stratification characteristics of the overlying soil and rock layers are clear, the resistivity from the surface down gradually increases, and the electrical layers are not uniform locally. During mining, the overlying strata are affected by mining, the electrical resistivity of the underlying aquifers increased to varying degrees, and the fluctuation of electrical resistivity increased while the aquifer’s water content decreased. After mining, the overlying aquifer has the phenomenon of ‘reduced resistivity and water recovery’. After a period of time, the overlying soil disturbance and overlying rock failure zone will gradually tend to be stable. Meanwhile, the aquifer structure and water content will also gradually recover. Our results could provide guidance for water resources protection in this region. Full article

Coal mining and ecological restoration activities significantly affect land surfaces, particularly vegetation. Long-term quantitative analyses of vegetation disturbance and restoration are crucial for effective mining management and ecological environmental supervision. In this study, using the Google Earth Engine and all available Landsat images from 1987 to 2020, we employed the Landsat-based Detection of Trends in Disturbance and Recovery (LandTrendr) algorithm and Support Vector Machine (SVM) to conduct a comprehensive analysis of the year, intensity, duration, and pattern of vegetation disturbance and restoration in the Heidaigou and Haerwusu open-pit coal mines (H-HOCMs) in the Jungar Coalfield of China. Our findings indicate that the overall accuracy for extractions of disturbance and restoration events in the H-HOCMs area is 83% and 84.5%, respectively, with kappa coefficients of 0.82 for both. Mining in Heidaigou has continued since its beginning in the 1990s, advancing toward the south and then eastward directions, and mining in the Haerwusu has advanced from west to east since 2010. The disturbance magnitude of the vegetation greenness in the mining area is relatively low, with a duration of about 4–5 years, and the restoration magnitude and duration vary considerably. The trajectory types show that vegetation restoration (R, 44%) occupies the largest area, followed by disturbance (D, 31%), restoration–disturbance (RD, 16%), disturbance–restoration (DR, 8%), restoration–disturbance–restoration (RDR), and no change (NC). The LandTrendr algorithm effectively detected changes in vegetation disturbance and restoration in H-HOCMs. Vegetation disturbance and restoration occurred in the study area, with a cumulative disturbance-to-restoration ratio of 61.79% since 1988. Significant restoration occurred primarily in the external dumps and continued ecological recovery occurred in the surrounding area. Full article

Aspilia grazielae (J. U. Santos) is an endemic plant species in Morro do Urucum in the Pantanal wetland (Brazil). A. grazielae is used for the restoration of areas impacted by iron mining activities. This study evaluates the diversity (composition, value and abundance) of endophytic fungal communities, considering parts of the plant and soil condition. The leaves and roots of A. grazielae were collected from native vegetation areas (NVA) and recovery areas (RCA) in Morro do Urucum. Illumina sequencing technology was used to investigate variation in endophytic fungal biodiversity. The operational taxonomic units detected in NVA ranged from 183 to 263 (leaf) and 115 to 285 (root), while RCA samples ranged from 200 to 282 (leaf) and 156 to 348 (root). Ascomycota phylum was the most common species among all plant samples. The most significant classes identified were Lecanoromycetes and Dothideomycetes that differed significantly (p ≤ 0.05) according to their plant hosts and soil stress. The relative abundance of Pestalotiopsis (Sordariomycetes class) and Stereocaulon (Lecanoromycetes class) genera was influenced by the iron mining activities according to the leaf samples analysed. However, the abundance and wealth of endophytic fungal communities in A. grazielae from RCA were evidence that could explain their high resilience to environmental disturbances and the source-sink dynamics of fungal propagules. Full article

The rock of weakly consolidated coal measure strata has the characteristics of low mechanical strength and strong water sensitivity. Under the stress and seepage disturbance caused by coal seam mining, the surrounding rock structure is prone to instability, which leads to mine safety accidents and water resources loss. In order to master the mechanical response and permeability evolution law of weakly consolidated rock under the disturbance of coal seam mining, the specimens of Jurassic mudstone, sandy mudstone, and sandstone in the Ili mining area of China were collected, and a triaxial compression seepage test was carried out. A comprehensive analysis was carried out on the mineral composition and microstructure characteristics of the rock. The results show the following: (1) Compared to the constant confining pressure condition, mining-induced stress promotes the fracture development rate of weakly consolidated rocks. The ratios of strain at the yield point of mudstone, sandy mudstone, and sandstone under mining-induced stress and constant confining pressure are 0.33, 0.43, and 0.79, respectively, and the ratios of strain at the failure point were 0.48, 0.52, and 0.72, respectively. (2) Under the condition of mining-induced stress, the permeability change range and the permeability recovery rate of the three types of rocks were different, which decreased in the order of mudstone, sandy mudstone, and sandstone. (3) In the process of the triaxial compression test, there was a strong hysteresis in the permeability change of the mudstone, and the permeability and hysteresis of the three types of rocks decreased with the increase in the clay mineral content. (4) Combined with the analysis of the rock mineral composition and microstructure characteristics, it is believed that the clay minerals in the rock after water mud and swelling are the main reasons for the hysteresis of the permeability change of weakly consolidated rock, and the content of clay minerals is the main factor affecting the permeability characteristics of the weakly consolidated rock. Full article

Micro-organisms play important roles in promoting soil ecosystem restoration, but much of the current research has been limited to changes in microbial community structure in general, and little is known regarding the more sensitive and indicative microbial structures or the responses of microbial diversity to environmental change. In this study, based on high-throughput sequencing and molecular ecological network analyses, the structural characteristics of bacterial communities were investigated in response to four different ecological restoration modes in a coal mining subsidence area located in northwest China. The results showed that among soil nutrients, nitrate-nitrogen and fast-acting potassium were the most strongly associated with microbial community structure under different ecological restoration types. Proteobacteria, Actinobacteria, and Acidobacteria were identified as important phyla regarding network connectivity and structural composition. The central natural recovery zone was found to have the smallest network size and low complexity, but high modularity and good microbial community stability. Contrastingly, a highly complex molecular ecological network of soils in the photovoltaic economic zone existed beneath the photovoltaic modules, although no key species, strong bacterial competition, poor resistance to disturbance, and a significant increase in the relative abundance of Gemmatimonadetes were found. Furthermore, the reclamation zone had the highest soil nutrient content, the most complex network structure, and the most key and indicator species; however, the ecological network was less stable and readily disturbed. Full article

A geoenvironmental assessment methodology was developed to estimate waste quantities and disturbances that could be associated with the extraction of undiscovered uranium resources and identify areas on the landscape where uranium and other constituents of potential concern (COPCs) that may co-occur with uranium deposits in this region are likely to persist, if introduced into the environment. Prior to this work, a method was lacking to quantitively assess the environmental aspects associated with potential development of undiscovered uranium resources at a scale of a uranium resource assessment. The mining method of in situ recovery (ISR) was historically used to extract uranium from deposits in the Goliad Sand of the Texas Coastal Plain. For this reason, the study’s methodology projected the following types of wastes and disturbances commonly associated with ISR based on historical ISR mining records: the mine area, affected aquifer volume, mine pore volume, water pumped and disposed during uranium extraction and restoration, and radon emissions. Within the tract permissive for the occurrence of undiscovered uranium resources, maps and statistics of factors were derived that indicate the potential contaminant pathways. The percentage of days meeting the criteria for air stagnation indicate the potential for radon accumulation; the geochemical mobility of COPCs in groundwater in combination with effective recharge indicates the potential for infiltration of surface-derived COPCs; the geochemical mobility of COPCs in groundwater combined with hydraulic conductivity indicates the propensity for transmitting fluids away from contaminated or mined aquifers; and finally, geochemical mobility of COPCs in surface water combined with the factor for climatic erosivity (R factor) indicates the potential for COPCs to persist in surface waters due to runoff. This work resulted in a new methodology that can be applied to any undiscovered mineral resource to better understand possible wastes and disturbances associated with extraction and identify areas on the landscape where COPCs are likely to persist. Full article