Search Results (104)

Nickel (Ni) ultrathin films exhibit phase-dependent electrical, magnetic, and optical characteristics that are significantly influenced by deposition methods. However, these films are inherently prone to rapid oxidation, with the oxidation rate dependent on substrate, temperature, and deposition parameters. The focus of this research is to investigate the temporal oxidation of RF-sputtered Ni ultrathin films on Corning glass under ambient atmospheric conditions and its impact on their structural, surface, and optical characteristics. Controlled film thicknesses were achieved through precise manipulation of deposition parameters, enabling the analysis of oxidation-induced modifications. Atomic force microscopy (AFM) revealed that films with high structural integrity and surface uniformity are exhibiting roughness values (Rq) from 0.679 to 4.379 nm of corresponding thicknesses ranging from 4 to 85 nm. Scanning electron microscopy (SEM) validated the formation of Ni grains interspersed with NiO phases, facilitating SPR-like effects. UV-visible spectroscopy is demonstrating thickness-dependent spectral (plasmonic peak) shifts. Finite Difference Time Domain (FDTD) simulations corroborate the observed thickness-dependent optical absorbance and the resultant shifts in the absorbance-induced plasmonic peak position and bandgap. Increased NiO presence primarily drives the enhancement of electromagnetic (EM) field localization and the direct impact on power absorption efficiency, which are modulated by the tunability of the plasmonic peak position. Our work demonstrates that controlled fabrication conditions and optimal film thickness selection allow for accurate manipulation of the Ni oxidation process, significantly altering their optical properties. This enables the tailoring of these Ni films for applications in transparent conductive electrodes (TCEs), magneto-optic (MO) devices, spintronics, wear-resistant coatings, microelectronics, and photonics. Full article

Pulse wave velocity (PWV) has been recognised as the gold standard for assessing arterial stiffness and a relevant indicator in diagnosing cardiovascular disease. Conventional approaches can be affected by factors such as the size of the probe, its positioning on the skin with the appropriate angle and magnitude of the incident force, or influenced by optical properties. Aiming at improving the assessment of PWV parameter, an important cardiovascular risk marker, the present study introduces a new arterial pulse wave measurement technique based on measurements of the impedance phase characteristics of giant magneto-impedance (GMI) sensors submitted to slight magnetic field variations caused by the displacement of a small magnetic marker placed on the patient’s skin, whose movement is coordinated by the local pressure wave. The proposed method eliminates the necessity of using probes with mechanical amplification, enhancing spatial resolution and usability in hard-to-reach anatomical regions through a contactless device unaffected by optical parameters. The obtained experimental results indicate the potential of the developed measurement system in measuring arterial pulse waveform and PWV. Full article

Liquid crystals based on dispersions of two-dimensional (2D) materials have recently been developed for light modulation, exhibiting superior performances compared to conventional organic liquid crystals in a variety of prototypical applications, including coloration, solar-blind communications and blue-light fluoresce. Among the diverse family of 2D liquid crystals, vermiculite-based liquid crystals stand out with advantages in low cost, ease of mass production and environmental sustainability, owing to the high natural abundance of the material. Here, we demonstrated magnetic-field tunable optics with 2D vermiculite dispersions prepared through a facile ‘exchange and redispersion’ method. By exploiting the intrinsic ion-exchange capability of clay minerals, we observed a significantly enhanced magneto-birefringence of the vermiculite dispersion upon replacing the native cations with magnetic ions, manifesting in a doubled Cotton–Mouton coefficient, representing the highest value among previous reports. Magnetization measurements reveal that there is a remarkable magnetic anisotropy in Fe ion-exchanged vermiculite samples in contrast to the isotropic magnetism of pristine vermiculite, which accounts for the observed enhancement of magneto-birefringence. Our findings demonstrate that ion exchange can serve as a simple and effective strategy to modulate the physical and chemical properties of 2D materials’ dispersions, thereby opening avenues for broader and more diverse applications. Full article

The extension direction of welding defects is random and uncontrollable, while magneto-optical imaging detection has a good imaging effect on defects perpendicular to the magnetic field direction. At present, magneto-optical detection methods may fail to detect small weld defects parallel to the direction of the magnetic field. To overcome this problem, a non-destructive testing method based on magneto-optical imaging under a vertical combined magnetic field (VCMF) is proposed. The paper first establishes a simulation model to compare and analyze the magnetic leakage characteristics of cross grooves under a constant magnetic field (CMF), an alternating magnetic field (AMF), a rotating magnetic field (RMF), a parallel combined magnetic field (PCMF), and VCMF excitation, proving that detection does not easily fail under VCMF. Secondly, by changing the size of the CMF in the VCMF simulation model, it was found that, as the CMF intensity increases, a new maximum value will appear on the side of the defect contour close to the sample area. This maximum value increases with the increase of the CMF intensity, which can lead to misjudgment of the defect contour, that is, false contours. Finally, magneto-optical imaging was used to verify the imaging effect of weld defects under VCMFs. The results indicate that more comprehensive defect information can be detected under VCMFs. When the maximum value of the excitation current of the AMF is at least 12 times the excitation current of the CMF, there will be no false contour defects. Full article

The increasing demand for image quality in aerospace remote sensing has led to higher performance requirements for inertial stabilization platforms equipped with image sensors, particularly in terms of bandwidth. To achieve wide-bandwidth control in optical stabilization platforms, engineers employ magneto-hydrodynamic (MHD) sensors as key components to enhance system performance because of their wide measurement bandwidth (5–1000 Hz). While MHD sensors offer a wide-frequency response, they are limited by a narrow measuring range and low sensitivity at low frequencies, making them unsuitable as standalone sensors. To address the challenges of over-range measurement and the loss of low-frequency signals, in this study, we developed a soft-switching adaptive Kalman filter method, which enables us to dynamically adjust the fusion weights in the Kalman filter so we can obtain wide-band measurement signals even when the MHD sensor experiences over-range conditions. The proposed method was validated with fusion experiments involving a fiber-optic gyroscope and an MHD sensor; the results demonstrate its ability to expand the sensing bandwidth, regardless of the operating conditions of the MHD sensor. Full article

In this paper, we investigate the optical absorption and luminescence spectra of rare-earth garnets activated by the terbium (Tb³⁺) ion, as well as their magneto-optical properties. Crystals of terbium gallium garnet (TbGaG) and terbium aluminum garnet (TbAlG) are considered. The focus is on the physical and optical properties and structural features of the energy levels of rare-earth ions in the crystal field of garnets. This work highlights the importance of studying intraconfigurational 4f-4f and interconfigurational 4f-5d transitions, as well as the influence of the crystal field on the magnetic and optical properties of materials. Integrated methods are used, including absorption spectroscopy, luminescence and magneto-optical studies, which allows us to obtain detailed information on the excited states of rare-earth ions. The experimental results show the presence of significant Zeeman shifts, as well as anisotropy of the absorption and luminescence spectra, depending on the orientation of the crystal lattice and the external magnetic field. This work contributes to our understanding of the mechanisms of light absorption and emission in rare-earth garnets, which may facilitate the development of new optoelectronic devices based on them. Full article

Infrared (IR) magneto-optical (MO) bi-imaging is an innovative method for detecting weld defects, and it is important to process both IR thermography and MO imaging characteristics of weld defects. IR thermography and MO imaging can not only run simultaneously but can also run separately in special welding processes. This paper studies the sensing processing of eddy current IR thermography and MO imaging for detecting weld defects of laser spot welding and butt joint laser welding, respectively. To address the issues of high-level noise and low contrast in eddy current IR detection thermal images interfering with defect detection and recognition, a method based on least squares and Gaussian-adaptive bilateral filtering is proposed for denoising eddy current IR detection thermal images of laser spot welding cracks and improving the quality of eddy current IR detection thermal images. Meanwhile, the image gradient is processed by Gaussian-adaptive bilateral filtering, and then the filter is embedded in the least squares model to smooth and denoise the image while preserving defect information. Additionally, MO imaging for butt joint laser welding defects is researched. For the acquired MO images of welding cracks, pits, incomplete fusions, burn-outs, and weld bumps, the MO image processing method that includes median filtering, histogram equalization, and Wiener filtering was used, which could eliminate the noise in an image, enhance its contrast, and highlight the weld defect features. The experimental results show that the proposed image processing method can eliminate most of the noise while retaining the weld defect features, and the contrast between the welding defect area and the normal area is greatly improved. The denoising effect using the Natural Image Quality Evaluator (NIQE) and the Blind Image Quality Index (BIQI) has been evaluated, further demonstrating the effectiveness of the proposed method. The differences among weld defects could be obtained by analyzing the gray values of the weld defect MO images, which reflect the weld defect information. The MO imaging method can be used to investigate the magnetic distribution characteristics of welding defects, and its effectiveness has been verified by detecting various butt joint laser welding weldments. Full article

Magneto-optical magnetic field/current sensors are based on the Faraday effect, which involves changing the polarized state of light. Polarimetric methods are therefore used for measuring polarization characteristics. Channeled polarimetry allows polarization information to be obtained from the analysis of the spectral domain. Although this allows the characterization of Faraday materials, the method has not yet been used for detection in magneto-optical sensors. This paper reports experimental results for magnetic field/current detection using the channeled polarimetry method. It is shown that in contrast to other methods, this method allows the detection of the phase shift caused by Faraday rotation alone, making the detection independent of temperature. Although an increase in measurement accuracy is required for practical applications by refining the data processing, the experimental results obtained show that this method offers a new approach to improving the performance of magneto-optical current sensors. Full article

It is difficult to detect and identify natural defects in welded components. To solve this problem, according to the Faraday magneto-optical (MO) effect, a nondestructive testing system for MO imaging, excited by an alternating magnetic field, is established. For the acquired MO images of crack, pit, lack of penetration, gas pore, and no defect, Gaussian filtering, bilateral filtering, and median filtering are applied for image preprocessing. The effectiveness of these filtering methods is evaluated using metrics such as peak signal–noise ratio (PSNR) and mean squared error. Principal component analysis (PCA) is employed to extract column vector features from the downsampled defect MO images, which then serve as the input layer for the error backpropagation (BP) neural network model and the support vector machine (SVM) model. These two models can be used for the classification of partial defect MO images, but the recognition accuracy for cracks and gas pores is comparatively low. To further enhance the classification accuracy of natural weld defects, a convolutional neural network (CNN) classification model and a ResNet50 classification model for MO images of natural weld defects are established, and the model parameters are evaluated and optimized. The experimental results show that the overall classification accuracy of the ResNet50 model is 99%. Compared with the PCA-SVM model and CNN model, the overall classification accuracy was increased by 7.4% and 1.8%, and the classification accuracy of gas pore increased by 10% and 4%, respectively, indicating that the ResNet50 model can effectively and accurately classify natural weld defects. Full article

Thin (~50 nm thick) BaM hexaferrite (BaFe₁₂O₁₉) films were grown on (1–102) and (0001) cut α-Al₂O₃ (sapphire) substrates via laser molecular beam epitaxy using a one- or two-stage growth protocol. The advantages of a two-stage protocol are shown. The surface morphology, structural and magnetic properties of films were studied using atomic force microscopy, reflected high-energy electron diffraction, three-dimensional X-ray diffraction reciprocal space mapping, powder X-ray diffraction, magneto-optical, and magnetometric methods. Annealed BaFe₁₂O₁₉/Al₂O₃ (1–102) structures consist of close-packed islands epitaxially bonded to the substrate. The hexagonal crystallographic axis and the easy axis (EA) of the magnetization of the films are deflected from the normal to the film by an angle of φ~60°. The films exhibit magnetic hysteresis loops for both in-plane H_in-plane and out-of-plane H_out-of-plane magnetic fields. The shape of M_out-of-plane(H_in-plane) and M_in-plane(H_in-plane) hysteresis loops strongly depends on the azimuth θ of the H_{in plane}, confirming the tilted orientation of the EA. The M_out-of-plane(H_out-of-plane) magnetization curves are caused by the reversible rotation of magnetization and irreversible magnetization jumps associated with the appearance and motion of domain walls. In the absence of a magnetic field, the magnetization is oriented at an angle close to φ. Full article

A preprocessing technique named “spiral annealing” was applied for the first time to magnetic microwires. In this process, the sample was arranged in a flat spiral shape during annealing, and subsequent measurements were conducted on the unbent sample with the induced stress distribution along and transverse to the sample. The research utilized both magnetic and magneto-optical methods. The anisotropy field magnitude in both the volume and surface of the microwire was measured, and for the first time, a direct correlation between the anisotropy field and the curvature of a spirally annealed microwire was established. Additionally, a connection between the type of surface domain structure and the degree of spiral curvature was identified. The preservation of the distribution of spiral annealing-induced magnetic properties both along and across the microwire is a key effect influencing the technological application of the microwire. The range of induced curvature within which a specific helical magnetic structure can exist was also determined. This insight links the conditions of spiral annealing to the selection of microwires as active elements in magnetic sensors. Full article

Molecular beam epitaxy (MBE) is a powerful tool in modern technologies, including electronic, optoelectronic, spintronic, and sensoric applications. The primary factor determining epitaxial heterostructure properties is the growth mode and the resulting atomic structure and microstructure. In this paper, we present a novel method for growing epitaxial layers and nanostructures with specific and optimized structural and magnetic properties by assisting the MBE process using electromagnetic and mechanical external stimuli: an electric field (EF), a magnetic field (MF), and a strain field (SF). The transmission of the external fields to the sample is realized using a system of specialized sample holders, advanced transfers, and dedicated manipulators. Examples of applications include the influence of MFs on the growth and anisotropy of epitaxial magnetite and iron films, the use of EFs for in situ resistivity measurements, the realization of in situ magneto-optic measurements, and the application of SFs to the structural modification of metal films on mica. Full article

Tb₃Sc_1.95Lu_0.05Al₃O₁₂ (TSLAG) crystals are novel and high-quality magneto-optical materials with the most promising application as the core component of Faraday devices. Cracking is an obstacle to TSLAG crystal growth and is closely influenced by crystal thermal stress distribution. In this work, the evolution of thermal stress during TSLAG crystal growth in the initial Czochralski (Cz) furnace is numerically studied. The reasons for high thermal stress in TSLAG crystal are explained based on the results about the melt flow, the temperature distribution in the furnace, and the crystal/melt interface shape. A large crucible with a shallow melt is proposed to address the problem of significant variations in melt depth during TSLAG crystal growth. Based on the numerical results, the proposed design can stabilize the melt flow structure, suppressing changes in the crystal/melt interface shape and effectively improving thermal stress in the TSLAG crystal growth process, which contributes to precisely regulating the preparation of large-sized high-quality TSLAG crystals. Full article

An integrated optical isolator is a crucial part of photonic integrated circuits (PICs). Existing optical isolators, predominantly based on the silicon-on-insulator (SOI) platform, face challenges in integrating with active devices. We propose a broadband, compact TM mode Mach–Zehnder optical isolator based on InP-on-insulator platforms. We designed two distinct magneto-optical waveguide structures, employing different methods for bonding Ce:YIG and InP, namely O₂ plasma surface activation direct wafer bonding and DVS-benzocyclobutene (BCB) adhesive bonding. Detailed calculations and optimizations were conducted to enhance their non-reciprocal phase shift (NRPS). At a wavelength of 1550 nm, the direct-bonded waveguide structure achieved a 30 dB bandwidth of 72 nm with a length difference of 0.256 µm. The effects of waveguide arm length, fabrication accuracy, and dimensional errors on the device performance are discussed. Additionally, manufacturing tolerances for three types of lithographic processes were calculated, serving as references for practical manufacturing purposes. Full article

Optical Motion Capture Systems (OMCSs) are considered the gold standard for kinematic measurement of human movements. However, in situations such as measuring wrist kinematics during a hairdressing activity, markers can be obscured, resulting in a loss of data. Other measurement methods based on non-optical data can be considered, such as magneto-inertial measurement units (MIMUs). Their accuracy is generally lower than that of an OMCS. In this context, it may be worth considering a hybrid system [MIMU + OMCS] to take advantage of OMCS accuracy while limiting occultation problems. The aim of this work was (1) to propose a methodology for coupling a low-cost MIMU (BNO055) to an OMCS in order to evaluate wrist kinematics, and then (2) to evaluate the accuracy of this hybrid system [MIMU + OMCS] during a simple hairdressing gesture. During hair cutting gestures, the root mean square error compared with the OMCS was 4.53° (1.45°) for flexion/extension, 5.07° (1.30°) for adduction/abduction, and 3.65° (1.19°) for pronation/supination. During combing gestures, they were significantly higher, but remained below 10°. In conclusion, this system allows for maintaining wrist kinematics in case of the loss of hand markers while preserving an acceptable level of precision (<10°) for ergonomic measurement or entertainment purposes. Full article