Search Results (32)

In this study, polyvinyl alcohol (PVA) films were reinforced with lignocellulosic nanofibers (LCNFs) extracted from bamboo shoot shells using a choline chloride-based deep eutectic solvent (DES). A filler loading of 10 wt% was identified as the optimal condition for enhancing film performance. To improve interfacial compatibility between the PVA matrix and LCNFs, three surface modification treatments were applied to the nanofibers: hydrochloric acid (HCl) hydrolysis, citric acid (CA) crosslinking, and a dual modification combining both methods (HCl&CA). Among all formulations, films incorporating dual-modified LCNF at 10 wt% loading exhibited the most significant improvements. Compared to neat PVA, these composites showed a 79.2% increase in tensile strength, a 15.1% increase in elongation at break, and a 33.1% enhancement in Young’s modulus. Additionally, thermal stability and barrier properties were improved, while water swelling and solubility were reduced. Specifically, the modified films achieved a thermal residue of 9.21% and the lowest degradation rate of 10.81%/min. Water vapor transmission rate and oxygen permeability decreased by 18.8% and 18.6%, respectively, and swelling and solubility dropped to 14.26% and 3.21%. These results highlight the synergistic effect of HCl hydrolysis and CA crosslinking in promoting uniform filler dispersion and strong interfacial adhesion, offering an effective approach to valorizing bamboo shoot shell waste into high-performance, eco-friendly packaging materials. Full article

Wood cellulose is an abundant bio-based resource with diverse applications in construction, cosmetics, packaging, and the pulp and paper industries. Transparent wood (TW) is a novel, high-quality wood material with several advantages over traditional transparent materials (e.g., glass and plastic). These benefits include renewability, UV shielding, lightweight properties, low thermal expansion, reduced glare, and improved mechanical strength. TW has significant potential for various applications, including transparent roofs, windows, home lighting structures, electronic devices, home decoration, solar cells, packaging, smart packaging materials, and other high-value-added products. The mechanical properties of TW, such as tensile strength and optical transmittance, are typically up to 500 MPa (Young’s modulus of 50 GPa) and 10–90%, respectively. Fabrication methods, wood types, and processing conditions significantly influence the mechanical and optical properties of TW. In addition, recent research has highlighted the feasibility of TW and large-scale production, making it an emerging research topic for future exploration. This review attempted to provide recent and updated manufacturing methods of TW as well as current and future applications. In particular, the effects of structural modification through various chemical pretreatment methods and impregnation methods using various polymers on the properties of TW biocomposites were also reviewed. Full article

Plant fibers’ wide availability and accessibility are the main causes of the growing interest in sustainable technologies. The two primary factors to consider while concentrating on composite materials are their low weight and highly specific features, as well as their environmental friendliness. Pineapple leaf fiber (PALF) stands out among natural fibers due to its rich cellulose content, cost-effectiveness, eco-friendliness, and good fiber strength. This review provides an intensive assessment of the surface treatment, extraction, characterization, modifications and progress, mechanical properties, and potential applications of PALF-based polymer composites. Classification of natural fibers, synthetic fibers, chemical composition, micro cellulose, nanocellulose, and cellulose-based polymer composite applications have been extensively reviewed and reported. Besides, the reviewed PALF can be extracted into natural fiber cellulose and lignin can be used as reinforcement for the development of polymer biocomposites with desirable properties. Furthermore, this review article is keen to study the biodegradation of natural fibers, lignocellulosic biopolymers, and biocomposites in soil and ocean environments. Through an evaluation of the existing literature, this review provides a detailed summary of PALF-based polymer composite material as suitable for various industrial applications, including energy generation, storage, conversion, and mulching films. Full article

Biodegradable mulching films are a very attractive solution to agronomical practices intended to achieve more successful crop results. And, in this context, the employment of agricultural and industrial food residues as starting material for their production is an alternative with economic and environmental advantages. This work reports the preparation of bilayer films having two different wettability characteristics from three bio-derived biopolymers: TEMPO-oxidized cellulose nanofibers isolated from infused Yerba Mate residues, Chitosan and Polylactic acid. The infused Yerba Mate residues, the isolated and oxidized cellulose nanofibers, and the films were characterized. Nanofibrillation yield, optical transmittance, cationic demand, carboxyl content, intrinsic viscosity, degree of polymerization, specific surface area and length were studied for the (ligno)cellulose nanofibers. Textural and chemical analysis, thermal and mechanical properties studies, as well as water and light interactions were included in the characterization of the films. The bilayer films are promising materials to be used as mulching films. Full article

Posidonia oceanica balls (POB), a kind of seagrass, are a significant environmental issue since they are annually discharged onto beaches. Their current usefulness limits interest in their management and enhances the environmental problem. Therefore, in this research, the potential of this lignocellulosic biomass was studied from a holistic biorefinery point of view. To this end, an in-depth study was carried out to select the best pathway for the integral valorization of POBs. First, an autohydrolysis process was studied for the recovery of oligosaccharides. Then, a delignification stage was applied, where, in addition to studying different delignification methods, the influence of the autohydrolysis pre-treatment was also investigated. Finally, cellulose nanofibers (CNFs) were obtained through a chemo-mechanical treatment. The results showed that autohydrolysis not only improved the delignification process and its products, but also allowed the hemicelluloses to be valorized. Acetoformosolv delignification proved to be the most successful in terms of lignin and cellulose properties. However, alkaline delignification was able to extract the highest amount of lignin with low purity. CNFs were also successfully produced from bleached solids. Therefore, the potential of POB as a feedstock for a biorefinery was confirmed, and the pathway should be chosen according to the requirements of the desired end products. Full article

(1) Background: Nanostructured cellulose has emerged as an efficient bio-adsorbent aerogel material, offering biocompatibility and renewable sourcing advantages. This study focuses on isolating (ligno)cellulose nanofibers ((L)CNFs) from barley straw and producing aerogels to develop sustainable and highly efficient decontamination systems. (2) Methods: (Ligno)cellulose pulp has been isolated from barley straw through a pulping process, and was subsequently deconstructed into nanofibers employing various pre-treatment methods (TEMPO-mediated oxidation process or PFI beater mechanical treatment) followed by the high-pressure homogenization (HPH) process. (3) Results: The aerogels made by (L)CNFs, with a higher crystallinity degree, larger aspect ratio, lower shrinkage rate, and higher Young’s modulus than cellulose aerogels, successfully adsorb and remove organic dye pollutants from wastewater. (L)CNF-based aerogels, with a quality index (determined using four characterization parameters) above 70%, exhibited outstanding contaminant removal capacity over 80%. The high specific surface area of nanocellulose isolated using the TEMPO oxidation process significantly enhanced the affinity and interactions between hydroxyl and carboxyl groups of nanofibers and cationic groups of contaminants. The efficacy in adsorbing cationic dyes in wastewater onto the aerogels was verified by the Langmuir adsorption isotherm model. (4) Conclusions: This study offers insights into designing and applying advanced (L)CNF-based aerogels as efficient wastewater decontamination and environmental remediation platforms. Full article

Nanofibrillated cellulose was extracted from potato peel waste using a fast and green method with a simple process. To extract cellulose and eliminate non-cellulosic constituents, alkaline and hydrogen peroxide treatments were performed under microwave irradiation. The nanofibrillated cellulose was extracted from purified cellulose via TEMPO oxidation followed by ultrasonication. The TEM, FTIR, XRD, and TGA experiments were used to evaluate the structural, crystalline, and thermal properties of cellulose fiber and nanofiber. The chemical and FTIR analysis of bleached fibers indicates that almost all non-cellulosic components of biomass have been eliminated. The diameter of the extracted nanofibers is in the range of 4 to 22 nm. In terms of crystallinity, extracted nanocellulose had 70% crystallinity, compared to 17% for unprocessed lignocellulose fibers, which makes it an excellent choice for use as a reinforcement phase in biobased composites. Thermogravimetric analysis reveals that cellulose nanofibers are less thermally stable than potato peel pure cellulose, but it has a higher char content (28%) than pure cellulose (6%), which signifies that the carboxylate functionality acts as a flame retardant. The comparison between cellulose derived from microwave and conventional extraction methods confirmed that their impact on the removal of non-cellulosic materials is nearly identical. Full article

Lignocellulose is a renewable ubiquitous material that comprises cellulose, hemicellulose, and lignin. Lignin has been isolated from different lignocellulosic biomass via chemical treatments, but there has been little or no investigation carried out on the processing of lignin from brewers’ spent grain (BSG) to the best of authors’ knowledge. This material makes up 85% of the brewery industry’s byproducts. Its high moisture content hastens its deterioration, which has posed a huge challenge to its preservation and transportation; this eventually causes environmental pollution. One of the methods of solving this environmental menace is the extraction of lignin as a precursor for carbon fiber production from this waste. This study considers the viability of sourcing lignin from BSG with the use of acid solutions at 100 °C. Structural and thermal analyses were carried out on extracted samples, and the results were compared with other biomass-soured lignin to assess the proficiency of this isolation technique. Wet BSG sourced from Nigeria Breweries (NB), Lagos, was washed and sun-dried for 7 days. Tetraoxosulphate (VI) (H₂SO₄), hydrochloric (HCl), and acetic acid, each of 10 M, were individually reacted with dried BSG at 100 °C for 3 h and designated as H2, HC, and AC lignin. The residue (lignin) was washed and dried for analysis. Wavenumber shift values from Fourier transform infrared spectroscopy (FTIR) show that intra- and intermolecular OH interactions in H2 lignin are the strongest and possess the highest magnitude of hydrogen-bond enthalpy (5.73 kCal/mol). The thermogravimetric analysis (TGA) results show that a higher lignin yield can be achieved when it is isolated from BSG, as 82.9, 79.3, and 70.2% were realized for H2, HC, and AC lignin. The highest size of ordered domains (0.0299 nm) displayed by H2 lignin from X-ray diffraction (XRD) informs that it has the greatest potential of forming nanofibers via electrospinning. The enthalpy of reaction values of 133.3, 126.6, and 114.1 J/g recorded for H2, HC, and AC lignin, respectively, from differential scanning calorimetry (DSC) results affirm that H2 lignin is the most thermally stable with the highest glass transition temperature (T_g = 107 °C). Full article

The use of agricultural waste biomass for nanocellulose production has gained interest due to its environmental and economic benefits compared to conventional bleached pulp feedstock. However, there is still a need to establish robust process technologies that can accommodate the variability of waste feedstocks and to understand the effects of feedstock characteristics on the final nanofiber properties. Here, lignocellulosic nanofibers with unique properties are produced from various waste biomass based on a simple and low-cost process using mild operating conditions. The process robustness is demonstrated by diversifying the feedstock, ranging from food crop waste (corn stover) to invasive grass species (reed canary grass) and industrial lignocellulosic residues (industrial hemp). This comprehensive study provides a thorough examination of the influence of the feedstocks’ physico-chemical characteristics on the conversion treatment, including process yield, degree of delignification, effectiveness of nanofibrillation, fiber morphology, surface charge, and density. Results show that nanofibers have been successfully produced from all feedstocks, with minor to no adjustments to process conditions. This work provides a framework for future studies to engineer nanocellulose with specific properties by taking advantage of biomass feedstocks’ intrinsic characteristics to enable versatile applications. Full article

As a transition strategy towards sustainability, food packaging plays a crucial role in the current era. This, carried out in a biorefinery context of agricultural residues, involves not only obtaining desirable products but a comprehensive utilization of biomass that contributes to the circular bioeconomy. The present work proposes the preparation of bioactive absorbent food pads through a multi-product biorefinery approach from bay tree pruning waste (BTPW). In a first step, chitosan aerogels reinforced with lignocellulose and cellulose micro/nanofibers from BTPW were prepared, studying the effect of residual lignin on the material’s properties. The presence of micro/nanofibers improved the mechanical performance (up to 60%) in addition to increasing the water uptake (42%) when lignin was present. The second step was to make them bioactive by incorporating bay leaf extract. The residual lignin in the micro/nanofibers was decisive, since when present, the release profiles of the extract were faster, reaching an antioxidant power of more than 85% after only 30 min. Finally, these bioactive aerogels were used as absorbent pads for fresh meat. With the use of the bioactive aerogels (with ≥2% extract), the meat remained fresh for 10 days as a result of delayed oxidation of the food during storage (20% metmyoglobin proportion). Full article

Lignin-containing cellulose nanofibrils (LCNFs) have emerged as a new class of nanocelluloses where the presence of residual lignin is expected to impart additional attributes such as hydrophobicity or UV-absorption. In the present work, LCNFs with a lignin content between 7 and 15 wt% were prepared via a TEMPO-mediated oxidation as chemical pretreatment followed by high-pressure homogenization. The impact of the carboxyl content (CC) on the properties of the resulting LCNF gel, in terms of lignin content, colloidal properties, morphology, crystallinity, and thermal stability, were investigated. It was found that lignin content was significantly decreased at increasing CC. In addition, CC had a positive effect on colloidal stability and water contact angle, as well as resulting in smaller fibrils. This lower size, together with the lower lignin content, resulted in a slightly lower thermal stability. The reinforcing potential of the LCNFs when incorporated into a ductile polymer matrix was also explored by preparing nanocomposite films with different LCNF contents that were mechanically tested under linear and non-linear regimes by dynamic mechanical analysis (DMA) and tensile tests. For comparison purposes, the reinforcing effect of the LCNFs with lignin-free CNFs was also reported based on literature data. It was found that lignin hinders the network-forming capacity of LCNFs, as literature data shows a higher reinforcing potential of lignin-free CNFs. Nonetheless, the tensile strength of the acrylic matrix was enhanced by 10-fold at 10 wt% of LCNF content. Full article

Vegetable supply in the world is more than double than vegetable intake, which supposes a significant waste of vegetables, in addition to the agricultural residues produced. As sensitive food products, the reasons for this waste vary from the use of only a part of the vegetable due to its different properties to the product appearance and market image. An alternative high-added-value application for these wastes rich in cellulose could be the reduction in size to produce lignocellulose micro- and nanofibrils (LCMNF). In this sense, a direct treatment of greengrocery waste (leek, lettuce, and artichoke) to produce LCMNFs without the extraction of cellulose has been studied, obtaining highly concentrated suspensions, without using chemicals. After drying the wastes, these suspensions were produced by milling and blending at high shear followed by several passes in the high-pressure homogenizer (up to six passes). The presence of more extractives and shorter fiber lengths allowed the obtention of 5–5.5% leek LCMNF suspensions and 3.5–4% lettuce LCMNF suspensions, whereas for artichoke, only suspensions of under 1% were obtained. The main novelty of the work was the obtention of a high concentration of micro- and nanofiber suspension from the total waste without any pretreatment. These high concentrations are not obtained from other raw materials (wood or annual plants) due to the clogging of the homogenizer, requiring the dilution of the sample up to 1% or the use of chemical pretreatments. Full article

Cellulose nanofiber is the world’s most advanced biomass material. Most importantly, it is biodegradable. In this work, nanofibers were obtained from pineapple leaves, a large solid waste in Colombia, using a combined extraction method (chemical procedures and ultrasound). The native fibers were bleached, hydrolyzed, treated with ultrasound, and characterized by scanning electron microscopy (SEM), infrared analysis (FTIR), thermogravimetric analysis (TGA), and transmission electron microscopy (TEM). As a comparison, a commercial microcrystalline cellulose sample was analyzed, which demonstrated the efficiency of cellulose extraction. The nanofibers had a diameter and a length of 18 nm and 237 nm, respectively, with a maximum degradation temperature of 306 °C. The analysis showed the efficiency of acid treatment combined with ultrasound to obtain nanofibers and confirmed that pineapple residues can be valorized by this method. These results indicate that lignocellulosic matrices from pineapple leaves have potential application for obtaining polymeric-type composite materials. Due to their morphology and characteristic physical properties, the cellulose nanofibers obtained in this work could be a promising material for use in a wealth of fields and applications such as filter material, high gas barrier packaging material, electronic devices, foods, medicine, construction, cosmetics, pharmacy, and health care, among others. Full article

Lignin is one of the most studied and analyzed materials due to its importance in cell structure and in lignocellulosic biomass. Because lignin exhibits autofluorescence, methods have been developed that allow it to be analyzed and characterized directly in plant tissue and in samples of lignocellulose fibers. Compared to destructive and costly analytical techniques, fluorescence microscopy presents suitable alternatives for the analysis of lignin autofluorescence. Therefore, this review article analyzes the different methods that exist and that have focused specifically on the study of lignin because with the revised methods, lignin is characterized efficiently and in a short time. The existing qualitative methods are Epifluorescence and Confocal Laser Scanning Microscopy; however, other semi-qualitative methods have been developed that allow fluorescence measurements and to quantify the differences in the structural composition of lignin. The methods are fluorescence lifetime spectroscopy, two-photon microscopy, Föster resonance energy transfer, fluorescence recovery after photobleaching, total internal reflection fluorescence, and stimulated emission depletion. With these methods, it is possible to analyze the transport and polymerization of lignin monomers, distribution of lignin of the syringyl or guaiacyl type in the tissues of various plant species, and changes in the degradation of wood by pulping and biopulping treatments as well as identify the purity of cellulose nanofibers though lignocellulosic biomass. Full article

The accumulation of dissolved and colloidal substances (DCS) in the increasingly closed paper circulating water system can seriously lower the productivity and safety of papermaking machines, and it has been a challenge to develop an adsorbent with low cost, high adsorption efficiency and large adsorption capacity for DCS removal. In this study, cationic lignocellulose nanofibers (CLCNF) were obtained by cationic modification of agricultural waste bagasse in deep eutectic solvents (DES) followed by mechanical defibrillation, and then CLCNF were employed as an adsorbent for DCS model contaminant polygalacturonic acid (PGA) removal. CLCNF was characterized by transmission electron microscopy, Fourier transform infrared, elemental analysis, X-ray diffraction, and thermogravimetric analysis. The analytical results confirmed the successful preparation of CLCNF with 4.6–7.9 nm diameters and 0.97–1.76 mmol/g quaternary ammonium groups. The effects of quaternary ammonium group contents, pH, contact time and initial concentration of PGA on the adsorption were investigated in a batch adsorption study. According to the results, the cationic modification significantly enhanced the adsorption of PGA by CLCNF and the adsorption performance increased with the increase of the quaternary ammonium group contents. The adsorption of PGA on CLCNF followed the pseudo-second-order and the fitted Langmuir isotherm model. The adsorption showed fast initial kinetics and the experimental maximum adsorption capacity was 1054 mg/g, which is much higher than PGA adsorbents previously reported in the literature. Therefore, CLCNF with high cationic group content developed in this paper is a promising adsorbent for DCS removal. Full article