Search Results (33)

Lead sulfide colloidal quantum dots (PbS QDs) have demonstrated great potential in short-wave infrared (SWIR) photodetectors due to their tunable bandgap, low cost, and broad spectral response. While significant progress has been made in surface ligand modification and defect state passivation, studies focusing on the interface between QDs and electrodes remain limited, which hinders further improvement in device performance. In this work, we propose an interface engineering strategy based on 3-aminopropyltriethoxysilane (APTES) to enhance the interfacial contact between PbS QD films and ITO interdigitated electrodes, thereby significantly boosting the overall performance of SWIR photodetectors. Experimental results demonstrate that the optimal 0.5 h APTES treatment duration significantly enhances responsivity by achieving balanced interface passivation and charge carrier transport. Moreover, The APTES-modified device exhibits a controllable dark current and faster photo-response under 1310 nm illumination. This interface engineering approach provides an effective pathway for the development of high-performance PbS QD-based SWIR photodetectors, with promising applications in infrared imaging, spectroscopy, and optical communication. Full article

This paper presents an analysis of the current state of processing lead–zinc ores from the Koskudyk deposit (Kazakhstan). At present, polymetallic ores are being extracted from the Ridder-Sokolnoye, Zyryanovskoye, Maleevskoye, and Achisai deposits. However, the reserves of rich and easily beneficiable ores are being depleted, and the supply of raw materials from the developed deposits does not exceed 25 years. As a result, more complex and difficult-to-enrich oxidized and mixed ores are being involved in production, and the extraction of non-ferrous metals from these ores presents a significant technological challenge. The most effective method for enriching oxidized polymetallic ores is flotation with preliminary sulfidization. Laboratory studies were conducted on a sample of oxidized lead–zinc ore from the Koskudyk deposit, which contains 79.69% oxidized lead compounds and 84.72% oxidized zinc compounds. This study examines the effect of sulfidization using sodium sulfide and determines the oxidative–reductive potential (ORP) levels for various reagent dosages. The experiments demonstrated that a sodium sulfide dosage of 700 g/t at an ORP of −200 mV yields the most effective lead flotation, resulting in a lead recovery of 50.07%. Zinc recovery remained relatively unchanged across all tests, confirming the limited response of oxidized zinc minerals under the applied sulfidization conditions. The highest beneficiation efficiency was achieved within the ORP range of −160 to −200 mV, beyond which lead recovery began to decline. The findings underscore the importance of optimizing ORP to ensure the formation of a stable sulfide film on mineral surfaces and efficient collector attachment. These results provide practical guidance for improving flotation performance of oxidized ores and demonstrate the need for additional activation strategies in zinc recovery. Full article

This paper investigates the corrosion behavior of mild steel in simulated oilfield wastewater under CO₂, H₂S, and their mixture. Using the electrical resistance method, the corrosion rates were monitored, and the influence of corrosion product films on overall performance was analyzed. The results show that the CO₂/H₂S mixture causes the highest corrosion rate. Metallographic examination and X-ray diffraction (XRD) provided insights into the nature of the corrosion products formed on the steel surface. While hydrogen sulfide (H₂S) does not prevent general corrosion, it plays a role in mitigating localized damage. Corrosion leads to deep, narrow pits that weaken the structural integrity without significant surface damage, making it more dangerous than uniform corrosion. In CO₂-only environments, electrochemical reactions form protective oxide layers. However, H₂S alters this process by forming iron sulfides (FeS), which are less protective but still act as a barrier against further corrosion. In mixed CO₂/H₂S environments, interactions between the gases complicate the corrosion dynamics, increasing medium aggressiveness and accelerating material degradation. Understanding these mechanisms is critical for the petroleum industry, where equipment is exposed to harsh conditions with varying CO₂ and H₂S concentrations. Recognizing the dual role of H₂S—its inability to inhibit general corrosion but its effectiveness in reducing pitting—can guide material selection and inhibitor development. This knowledge enhances the durability and safety of oil and gas infrastructure by addressing the most damaging forms of corrosion. Full article

The transformations of iron (Fe), phosphorus (P), and sulfide (S) have been previously investigated in many areas, but quantifying the effects of the seasons on nutrient transformations and bacterial community distributions is a major issue that requires urgent attention in areas with serious anthropogenic disturbance. The authors used the diffusive gradients in thin films (DGTs) technique and 16S rRNA gene sequencing to determine the spatial heterogeneity in the nutrient distribution and bacterial community structure in the overlying water and sediment in the Pearl River Delta (PRD). Sampling campaigns were conducted in summer and winter. The results show that the nutrient salts exhibited greater differences in time than in space and there were higher water pollution levels in winter than in summer. During summer, the abundant non-point source pollution from the rainfall input provided a rich substrate for the bacteria in the water, leading to a strong competitiveness of the PAOs and nitrifying bacteria. Meanwhile, a high temperature was favorable for the exchange of elements at the SWI, with a greater release of P, Fe, and N, while, with the low temperatures and high DO and nutrient salts seen in winter, the SOB and denitrifying bacteria were active, which correctly indicated the high concentration of SO₄²⁻ and NH₄⁺-N in the water. The microbial diversity and abundance were also affected by the season, with a higher richness and diversity of the microbial communities in summer than in winter, and the high salinity and nutrient salt concentration had a significant inhibitory effect on the microorganisms. A Mantel test revealed that the spatiotemporal distribution patterns of the dominant bacteria were closely related to the TOC and DO levels and played an important role in the P, Fe, S, and N cycle. These observations are important for understanding the nutrient salt transformation and diffusion in the Pearl River Delta. Full article

The efficient recovery of fine argentite from polymetallic lead–zinc (Pb–Zn) sulfide ore is challenging. This study investigated nanobubble (NB) adsorption on the argentite surface and its role in enhancing fine argentite flotation using various analytical techniques, including contact angle measurements, adsorption capacity analysis, infrared spectroscopy, zeta potential measurements, turbidity tests, microscopic imaging, scanning electron microscopy, and flotation experiments. Results indicated that the NBs exhibited long-term stability and were adsorbed onto the argentite surface, thereby enhancing surface hydrophobicity, reducing electrostatic repulsion between fine argentite particles, and promoting particle agglomeration. Furthermore, the NBs formed a thin film on the argentite surface, which decreased the adsorption of sodium diethyldithiocarbamate. Microflotation tests confirmed that the introduction of NBs considerably enhanced the recovery of argentite using flotation technology. Full article

During the process of liquefied petroleum gas (LPG) exploitation, various sulfide-containing gases are produced, which significantly bring about corrosion attacks to copper equipment and facilities. Investigations on the effects of sulfides, hydrogen sulfide (H₂S), carbonyl sulfide (COS), and ethanethiol (C₂H₆S) on copper corrosion and synergistic mechanisms are of great significance for LPG production. This paper studied the synergistic corrosion effects of mixed sulfide-containing gases in LPG on copper plates, including the influence of H₂S + COS, H₂S + C₂H₆S, as well as H₂S + COS + C₂H₆S. The results showed that there exists an apparent synergistic effect between different sulfide-containing gases, which decreased the critical point of corrosion and enhanced the severity of copper corrosion. SEM observation on corrosion products with the addition of different sulfide-containing gases demonstrated that the microstructures of corrosion products are significantly different, which reveals different corrosion mechanisms. By characterizing the corrosion products on copper surfaces, corresponding corrosion mechanisms were proposed. Individual H₂S reacts with copper directly as chemical corrosion. The presence of water leads to the dissolution of H₂S into water film at the copper surface and results in electrochemical corrosion in nature. COS tends to decompose into acidic gas H₂S and CO₂, which accelerates the electrochemical corrosion at the copper surface. C₂H₆S can react with copper directly as chemical corrosion. A mixture of different sulfur-containing gases enhanced the corrosion attack by synergistic effect. Full article

Lead sulfide (PbS) on the nanoscale was synthesized via a chemical route at room temperature using lead nitrate {Pb(NO₃)₂} and sodium sulfide (Na₂S). The Na₂S was prepared at ~105 °C using sodium hydroxide (NaOH) and sulfur (S) powder. The produced PbS, denoted as Lab-PbS, was compared with a high-concentration PbS phase of galena. The produced Na₂S and Lab-PbS were examined using scanning electron microscopy and energy dispersive X-ray spectroscopy for microstructural and chemical analysis. The results confirmed a high-purity PbS compound (>99%) with a nanoscale particle size. The results showed that ultrasonic agitation was vital for obtaining the nanoparticle size of the Lab-PbS. Furthermore, thin films from the synthesized Lab-PbS and galena were successfully thermally evaporated on glass, quartz, and silicon substrates. The formation of nanometric grains was confirmed by scanning electron microscopy (SEM). XRD and FTIR spectroscopy were carried out for the Lab-PbS, galena fine powders, and galena thin films. The average crystal diameter was calculated for the galena thin films and was found to be approximately 26.6 nm. Moreover, the UV–Visible transmission curve was measured for the thin films in the wavelength range of 200–1100 nm in order to calculate the bandgap energy (E_g) for the thin films. The values of E_g were approximately 2.65 eV and 2.85 eV for the galena and Lab-PbS thin films, respectively. Finally, the sintering of the Lab-PbS and galena powders was carried out at ~700 °C for 1 h under vacuum, achieving relative densities of ~98.1% and ~99.2% for the Lab-PbS and galena, respectively. Full article

As a layered material with single/multi-atom thickness, two-dimensional transition metal sulfide WS₂ has attracted extensive attention in the field of science for its excellent physical, chemical, optical, and electrical properties. The photoelectric properties of WS₂ are even more promising than graphene. However, there are many existing preparation methods for WS₂, but few reports on its direct growth on tungsten films. Therefore, this paper studies its preparation method and proposes an innovative two-dimensional material preparation method to grow large-sized WS₂ with higher quality on metal film. In this experiment, it was found that the reaction temperature could regulate the growth direction of WS₂. When the temperature was below 950 °C, the film showed horizontal growth, while when the temperature was above 1000 °C, the film showed vertical growth. At the same time, through Raman and band gap measurements, it is found that the different thicknesses of precursor film will lead to a difference in the number of layers of WS₂. The number of layers of WS₂ can be controlled by adjusting the thickness of the precursor. Full article

This research article provides a comprehensive investigation into the optoelectronic characteristics of three distinct types of cadmium sulfide (CdS) thin films, namely: (a) conventionally prepared CdS thin films using chemical bath deposition (CBD-CdS), (b) CdS thin films produced via chemical bath deposition with the inclusion of zinc (CBD-Cd_(1−x)Zn_xS, x = 0.3), and (c) CdS thin films synthesized using a seed-assisted approach, treated with ethylenediaminetetraacetic acid (EDTA), and incorporating zinc (ED/CBD + EDTA-Cd_(1−x)Zn_xS). The investigation reveals that the crystallite size of these thin films decreases upon the addition of EDTA to the reaction solution, leading to an increase in the inter-planar spacing and dislocation density. Furthermore, a blue shift in the transmittance edge of the ED/CBD + EDTA-Cd_(1−x)Zn_xS samples compared to CBD-CdS implies modifications in the band gaps of the deposited films. The incorporation of Zn²⁺ into the reaction solution results in an increased band gap value of up to 2.42 eV. This suggests that Cd_(1−x)Zn_xS thin films permit more efficient photon transmission compared to conventional CdS. Among the three types of films studied, ED/CBD + EDTA-Cd_(1−x)Zn_xS exhibits the highest optical band gap of 2.50 eV. This increase in the optical band gap is attributed to the smaller crystallite size and the splitting of the tail levels from the band structure. Additionally, the increment in the optical band gap leads to reduced light absorption at longer wavelengths, thereby enhancing the electrical properties. Notably, ED/CBD + EDTA-Cd_(1−x)Zn_xS thin films demonstrate improved photovoltaic performance in a photoelectrochemical (PEC) cell, characterized by enhanced open-circuit voltage (363 mV, V_OC), short-circuit current (35.35 μA, I_SC), and flat-band voltage (−692 mV, V_fb). These improvements are attributed to the better adhesion of CdS to the fluorine-doped tin oxide (FTO) substrate and improved inter-particle connectivity. Full article

In this study, a sol-gel film based on lead sulfide (PbS) quantum dots incorporated into a host network was synthesized as a special nanostructured composite material with potential applications in temperature sensor systems. This work dealt with the optical, structural, and morphological properties of a representative PbS quantum dot (QD)-containing thin film belonging to the Al₂O₃–SiO₂–P₂O₅ system. The film was prepared using the sol-gel method combined with the spin coating technique, starting from a precursor solution containing a suspension of PbS QDs in toluene with a narrow size distribution and coated on a glass substrate in a multilayer process, followed by annealing of each deposited layer. The size (approximately 10 nm) of the lead sulfide nanocrystallites was validated by XRD and by the quantum confinement effect based on the band gap value and by TEM results. The photoluminescence peak of 1505 nm was very close to that of the precursor PbS QD solution, which demonstrated that the synthesis route of the film preserved the optical emission characteristic of the PbS QDs. The photoluminescence of the lead sulfide QD-containing film in the near infrared domain demonstrates that this material is a promising candidate for future sensing applications in temperature monitoring. Full article

PbS films grown on quartz substrates by the chemical bath deposition method were annealed in an O₂ atmosphere to investigate the role of oxygen in the sensitization process at different annealing temperatures. The average grain size of the PbS films gradually increased as the annealing temperature increased from 400 °C to 700 °C. At an annealing temperature of 650 °C, the photoresponsivity and detectivity reached 1.67 A W⁻¹ and 1.22 × 10¹⁰ cm Hz^1/2 W⁻¹, respectively. The role of oxides in the sensitization process was analyzed in combination with X-ray diffraction and scanning electron microscopy results, and a three-dimensional network model of the sensitization mechanism of PbS films was proposed. During the annealing process, O functioned as a p-type impurity, forming p⁺-type PbS layers with high hole concentrations on the surface and between the PbS grains. As annealing proceeds, the p⁺-type PbS layers at the grain boundaries interconnect to form a three-dimensional network structure of hole transport channels, while the unoxidized p-type PbS layers act as electron transport channels. Under bias, photogenerated electron–hole pairs were efficiently separated by the formed p⁺-p charge separation junction, thereby reducing electron–hole recombination and facilitating a higher infrared response. Full article

Photoluminescent (PL) layers and electroluminescent (EL) systems have gained significant attention for their applications in constructing flat panels, screen monitors, and lighting systems. In this study, we present a groundbreaking approach to fabricating temperature sensors using barium-calcium zirconium titanate (BCZT) with thermo-optic properties, leading to the development of opto-thermal sensors for electric vehicle battery packs. We prepared zinc sulfide (ZnS) fluorescent films on BCZT ceramics, specifically two optimal compositions, BCZT0.85 (Ba_0.85Ca_0.15Zr_0.1Ti_0.9O₃) and BCZT0.9 (Ba_0.9Ca_0.1Zr_0.1Ti_0.9O₃), via the solid-state reaction method for the dielectric layer. The BCZT powders were calcined at varying temperatures (1200 and 1250 °C) and dwell times (2 and 4 h). The resulting phase formation and microstructure characteristics were analyzed using X-ray diffraction and scanning electron microscopy, respectively. Our investigation aimed to establish a correlation between the dielectric behavior and optical properties to determine the optimal composition and conditions for utilizing BCZT as thermal detectors in electric vehicle battery packs. All BCZT powders exhibited a tetragonal phase, as confirmed by JCPDS No. 01-079-2265. We observed an increase in the dielectric constant with higher calcining temperatures or longer dwell times. Remarkably, BCZT0.85 ceramic sintered at 1250 °C for 4 h displayed the highest dielectric constant of 15,342, establishing this condition as optimal for preparing the dielectric film with a maximum dielectric constant of 42. Furthermore, we investigated the temperature-dependent electroluminescence intensity of the samples, revealing a significant enhancement with increasing temperature, reaching its peak at 80 °C. Additionally, we observed a positive correlation between electroluminescence intensity and dielectric constant, indicating the potential for improved opto-thermal sensors. The findings from this study offer promising opportunities for the development of advanced opto-thermal sensors with potential applications in electric vehicle battery packs. Our work contributes to the expanding field of photoluminescent and electroluminescent systems by providing novel insights into the design and optimization of efficient and reliable sensors for thermal monitoring in electric vehicle technologies. Full article

Wear tends to shorten tool life, reduce component quality. To prevent or postpone the wear of tool steel forming tools, methods to increase wear resistance, such as increasing the material hardness, optimizing the carbide distribution and application of surface coatings, are often used. However, the formation of lubricating phases in steels leading to anti-attrition is less investigated. The friction behavior of three steels were investigated thoroughly by a tribo test with different normal loads. A Field-emission scanning electron microscope (FE-SEM) along with energy dispersive X-ray spectroscopy (EDS) were used to characterize the microstructure as well as the influence of the precipitated phases on the wear mechanisms. Results showed the friction coefficient decreased with increasing normal load, whereas the wear rate increased with increasing normal load. Compared with SKD11 and DC53 steels, the friction coefficient and wear volume of SLD-MAGIC steel were reduced by 0.1 to 0.3 and 10% to 30%, respectively. With the increase of normal load, the wear mechanism changed in order from abrasive wear, adhesive wear to oxidation wear. The more carbide contents, the rounder the carbide, the better the wear resistance of the tool steel. It can be shown that, under different normal loads, SLD-MAGIC exhibits better wear performance than SKD11 and DC53 tool steels, which is mainly due to the self-lubricating phenomenon of SLD-MAGIC steel. The self-lubricating mechanism was due to the fact that the exfoliated sulfide during wear formed a lubricating film to reduce wear. Full article

Colloidal quantum dots (CQDs) are gaining increasing attention for gas sensing applications due to their large surface area and abundant active sites. However, traditional resistor-type gas sensors using CQDs to realize molecule recognition and signal transduction at the same time are associated with the trade-off between sensitivity and conductivity. This limitation has restricted their range of practical applications. In this study, we propose and demonstrate a monolithically integrated field-effect transistor (FET) gas sensor. This novel FET-type gas sensor utilizes the capacitance coupling effect of the CQD sensing film based on a floating gate, and the quantum capacitance plays a role in the capacitance response of the CQD sensing film. By effectively separating the gate sensing film from the two-dimensional electron gas (2DEG) conduction channel, the lead sulfide (PbS) CQD gate-sensitized FET gas sensor offers high sensitivity, a high signal-to-noise ratio, and a wide range, with a real-time response of sub-ppb NO₂. This work highlights the potential of quantum dot-sensitized FET gas sensors as a practical solution for integrated gas sensor chip applications using CQDs. Full article

The film casting method is implemented to synthesize a series of films consisting of polyvinyl alcohol (PVA) films and 4 wt%, 8 wt%, and 12 wt% lead sulfide (PbS) nanoparticles (NPs). X-ray diffraction (XRD), Fourier-transform infrared spectroscopy (FTIR), and Ultraviolet-visible (UV-vis) spectroscopy were used to ensure the impact of PbS loading on PVA properties, particularly optical ones. The FTIR results show a decrease in the intensity for all the bands and the XRD results show different features for the composites from that of the pure PVA. The optical properties, including optical transmission, surface reflection, and absorption, were investigated. Additionally, the significant optical parameters, for instance, the dielectric nature and refractive index of the films, were analyzed. The findings have shown that PbS NPs in the PVA films decrease UV and visible transmission through polymer composites and increase their ability to reflect the incident light. Tauc’s equation is applied to determine the optical bandgap energy (E_g) and verify whether it is direct or indirect. Using the relation between photon energy and optical dielectric loss, the E_g was measured and the type of electron transition was measured, which eases the exponent value (𝜸) specification from Tauc’s method. The E_g decreases from 6.3 eV to 5.25 eV when PbS NPs are added. The refractive index is improved from 1.27 to 2.16 for the polymer nanocomposite (NCPs) film with optimum PbS NPs. Then, the Wemple–DiDomenico model corresponding to a single oscillator is applied to the dispersive medium to determine the refractive index dispersion. Both the dispersive energy ($E_d$) and single-oscillator energy ($E_o$) are evaluated accurately. Moreover, the variation of both real and imaginary parts of the dielectric constant of polymer films were studied. Finally the optical parameters such as charge density, dielectric constant at high frequencies, optical mobility (µ), angular frequency (${\omega }_p$), optical resistivity (ρ), and relaxation time (τ) of electrons are shown quantitatively. The ${\omega }_p$ of the electron is increased from 1.06 × 10²⁹ to 81.5 × 10²⁹ Hz when the PbS NPs is added. The µ of the electrons is also increased from 4.85 to 6.22 cm²/(V·s) by adding the PbS NP. Full article