Search Results (66)

This paper presents a comprehensive analysis and simulation of a cost-effective optical Intensity-Modulation/Direct-Detection (IM/DD) Orthogonal Frequency Division Multiplexing (OFDM) system. Implemented via a MATLABR2024a and OptiSystem 23 co-simulation environment, the study evaluates a 4-QAM modulated link over a 120 km transmission distance, providing detailed investigations into signal spectral properties and constellation characteristics. To address the critical performance limitation posed by high Peak-to-Average Power Ratio (PAPR), a novel Hybrid Whale Optimization Algorithm with Selective Mapping (HWOA-SLM) is proposed. Simulation results demonstrate that the proposed scheme significantly outperforms conventional reduction techniques; specifically, at a Complementary Cumulative Distribution Function (CCDF) of 10⁻² and a fixed computational budget of 256 evaluations, the HWOA-SLM achieves a PAPR reduction gain of 3.9 dB relative to the original OFDM signal. Furthermore, in terms of algorithmic efficiency, it outperforms standard Genetic Algorithm (GA) and WOA-based SLM techniques by approximately 0.4 dB under identical computational budgets. Parametric analysis further confirms that increasing population size and iteration numbers consistently improves convergence, thereby minimizing non-linear distortions and enhancing signal integrity. Moreover, the technique exhibits superior Bit Error Rate (BER) performance, delivering Optical Signal-to-Noise Ratio (OSNR) gains of 0.63 dB, 1.31 dB, and 2.0 dB over standard WOA-SLM, GA-SLM, and conventional SLM, respectively. Conclusively, the HWOA-SLM offers a favorable trade-off between computational complexity and reduction efficiency, validating its potential for reliable, high-speed optical communication networks. Full article

In this study, we consider multi-pair user frequency division duplexing massive MIMO relay systems and design a two-stage combining and beamforming (TSCB) scheme based on statistical channel state information (S-CSI). By leveraging S-CSI to co-design the pre-combining matrix and the pre-beamforming matrix, the scheme reduces the equivalent channel matrix dimensions, thereby cutting the pilot overhead. In the first stage, the two matrices are constructed through a selection of beams from a discrete Fourier transform codebook and mathematically cast as a multivariate optimization problem. An alternative optimization algorithm is proposed by splitting it into three sub-problems. The first two are 0–1 integer programming problems solved by iterative beam selection, while the third is a convex problem that is solved using a convex optimization algorithm. In the second stage, the reduced-dimension equivalent matrices are then estimated with low overhead, and a digital precoding matrix is then designed using zero-forcing algorithms. Simulations confirm the TSCB scheme’s superior ESE performance over that of existing methods. Full article

Orthogonal frequency-division multiplexing (OFDM) has been adopted as the baseline waveform for sixth-generation (6G) networks owing to its robustness and high spectral efficiency. However, its inherently high peak-to-average power ratio (PAPR) limits power amplifier efficiency and causes nonlinear distortion, particularly in power- and cost-constrained 6G scenarios. To address these challenges, we propose a constant-envelope cyclic-prefix OFDM (CE-CP-OFDM) transceiver under the CP-OFDMA framework, which achieves high spectral efficiency while maintaining low PAPR. Specifically, we introduce a spectrally efficient subcarrier mapping scheme with partial frequency overlap and establish a multiuser received signal model under frequency-selective fading channels. Subsequently, to minimize channel estimation error, we develop an optimal multiuser CE pilot design by exploiting frequency-domain phase shifts and generalized discrete Fourier transform-based time-domain sequences. For large-scale multiuser scenarios, a joint delay–frequency-domain channel estimation method is proposed, complemented by a low-complexity linear minimum mean square error (LMMSE) estimator in the delay domain. To mitigate inter-symbol and multiple-access interference, we further design an iterative frequency-domain LMMSE (FD-LMMSE) equalizer based on the multiuser joint received-signal model. Numerical results demonstrate that the proposed CE-CP-OFDM transceiver achieves superior bit-error-rate performance compared with conventional waveforms while maintaining high spectral efficiency. Full article

With the increasing sophistication of electromagnetic environments in modern combat platforms, joint sensing and communication (JSAC) technology has emerged as a critical research frontier. Among these, JSAC waveform design plays a crucial role, as it enables the simultaneous achievement of both sensing and communication functions using the same transmit waveform. This paper presents a novel waveform design for a multi-input multi-output (MIMO) JSAC system. The proposed design leverages orthogonal frequency division multiplexing (OFDM) to reduce signal interference through low cross-correlation characteristics. Linear frequency modulation (LFM) is used as the carrier waveform, effectively narrowing the main lobe width of the autocorrelation function. We introduce phase perturbation into binary phase shift keying (BPSK) signals to enhance waveform performance, formulating the resulting problem as a high-dimensional, non-convex optimization challenge. To address this, we propose a hybrid optimization algorithm QGPV combining a quantum genetic algorithm (QGA), quantum particle swarm optimization (QPSO), and variable neighborhood search (VNS). The simulation results demonstrate that the proposed algorithm achieves superior performance compared with several typical methods. Notably, the peak sidelobe level (PSL) can be suppressed to around −21 dB with five iterations, highlighting the efficiency of the optimization process. These results validate the effectiveness of the proposed approach, showing improved waveform characteristics with an acceptable trade-off in communication performance. Full article

Reconfigurable Intelligent Surfaces (RISs) are among the key technologies envisaged for sixth-generation (6G) multiple-input multiple-output (MIMO)–orthogonal frequency division multiplexing (OFDM) wireless systems. However, their passive nature and the frequent absence of a line-of-sight (LoS) path in dense urban environments make uplink channel estimation and localization challenging tasks. Therefore, to achieve channel estimation and localization, this study models the RIS-mobile station (MS) channel as a double-sparse angular structure and proposes a hybrid channel parameter estimation framework for RIS-assisted MIMO-OFDM systems. In the hybrid framework, Simultaneous Orthogonal Matching Pursuit (SOMP) first estimates coarse angular supports. The coarse estimates are refined by a novel refinement stage employing a Variational Bayesian Expectation Maximization (VBEM)-based Off-Grid Sparse Bayesian Learning (OG-SBL) algorithm, which jointly updates azimuth and elevation offsets via Newton-style iterations. An Angle of Arrival (AoA)–Angle of Departure (AoD) matching algorithm is introduced to associate angular components, followed by a 3D localization procedure based on non-LoS (NLoS) multipath geometry. Simulation results show that the proposed framework achieves high angular resolution; high localization accuracy, with 97% of the results within 0.01 m; and a channel estimation error of 0.0046% at 40 dB signal-to-noise ratio (SNR). Full article

Massive multiple input–multiple output (M-MIMO) is a promising and pivotal technology in contemporary wireless communication systems that can effectively enhance link reliability and data throughput, especially in uplink scenarios. Even so, the receiving end requires more computational complexity to reconstitute the signal. This problem has emerged in fourth-generation (4G) MIMO system; with the dramatic increase in demand for devices and data in beyond-5G (B5G) systems, this issue will become yet more obvious. To take into account both complexity and signal-revested capability at the receiver, this study uses the matrix iteration method to avoid the staggering amount of operations produced by the inverse matrix. Then, we propose a highly efficient multi-user detector (MUD) named hybrid SOR-based Chebyshev acceleration (CHSOR) for the uplink of M-MIMO orthogonal frequency-division multiplexing (OFDM) and universal filtered multi-carrier (UFMC) waveforms, which can be promoted to B5G developments. The proposed CHSOR scheme includes two stages: the first consists of successive over-relaxation (SOR) and modified successive over-relaxation (MSOR), combining the advantages of low complexity of both and generating a better initial transmission symbol, iteration matrix, and parameters for the next stage; sequentially, the second stage adopts the low-cost iterative Chebyshev acceleration method for performance refinement to obtain a lower bit error rate (BER). Under constrained evaluation settings, Section (Simulation Results and Discussion) presents the results of simulations performed in MATLAB version R2022a. Results show that the proposed detector can achieve a 91.624% improvement in BER performance compared with Chebyshev successive over-relaxation (CSOR). This is very near to the performance of the minimum mean square error (MMSE) detector and is achieved in only a few iterations. In summary, our proposed CHSOR scheme demonstrates fast convergence compared to previous works and as such possesses excellent BER and complexity performance, making it a competitive solution for uplink M-MIMO B5G systems. Full article

Satellite Internet is the key to integrated air–space–ground communication, while the design of waveforms with high spectrum efficiency is an intrinsic requirement for high-speed data transmission in satellite Internet. Time-domain synchronous orthogonal frequency division multiplexing (TDS-OFDM) technology can significantly improve spectrum utilization efficiency by using PN sequences instead of traditional CP cyclic prefixes. However, it also leads to time-domain aliasing between PN sequences and data symbols, posing a serious challenge to channel estimation. To solve this problem, a compressive sensing-based coding iterative channel estimation method for the TDS-OFDM system is proposed in this paper. This method innovatively combines compressive sensing channel estimation technology with the Reed–Solomon low-density parity-check cascade coding (RS-LDPC) scheme, and achieves performance improvements as follows: (1) Construct the iterative optimization mechanism for the compressive sensing algorithm and equalization feedback loop. (2) RS-LDPC cascaded coding is employed to enhance the anti-interference and error correction capability of system. (3) Design the recoding link of error-corrected data to improve the accuracy of sensing matrix. The simulation results demonstrate that compared with conventional methods, the proposed method can obviously converge on the mean squared errors (MSEs) of channel estimation and significantly reduce the bit error rate (BER) of the system. Full article

This paper proposes a source encoding rate control and cross-layer data stream allocation scheme for uplink millimeter-wave (mmWave) multi-user massive MIMO (MU-mMIMO) orthogonal frequency division multiplexing (OFDM) hybrid beamforming video communication systems. Unlike most previous studies that focus on the downlink scenario, our proposed scheme optimizes the uplink transmission while also addressing the limitation of prior works that only consider single-data-stream users. A key distinction of our approach is the integration of cross-layer resource allocation, which jointly considers both the physical layer channel state information (CSI) and the application layer video rate-distortion (RD) function. While traditional methods optimize for spectral efficiency (SE), our proposed method directly maximizes the peak signal-to-noise ratio (PSNR) to enhance video quality, aligning with the growing demand for high-quality video communication. We introduce a novel iterative cross-layer dynamic data stream allocation scheme, where the initial allocation is based on conventional physical-layer data stream allocation, followed by iterative refinement. Through multiple iterations, users with lower PSNR can dynamically contend for data streams, leading to a more balanced and optimized resource allocation. Our approach is a general framework that can incorporate any existing physical-layer data stream allocation as an initialization step before iteration. Simulation results demonstrate that the proposed cross-layer scheme outperforms three conventional physical-layer schemes by 0.4 to 1.14 dB in PSNR for 4–6 users, at the cost of a 1.8 to 2.3× increase in computational complexity (requiring 3.6–5.8 iterations). Full article

Estimating the downlink (DL) channel covariance matrix (CCM) is crucial for beamforming and capacity optimization in massive MIMO frequency division duplexing (FDD) systems, yet it poses significant challenges due to the lack of direct channel reciprocity. To address this issue, a turbo channel covariance conversion (Turbo-CCC) algorithm is proposed to enhance estimation accuracy and robustness by utilizing the angular power spectrum (APS) reciprocity. Specifically, based on the electromagnetic wave propagation characteristics, we model the APS as multikernel functions. On this basis, we then develop the Turbo-CCC algorithm by integrating the orthogonal approximate message passing (OAMP) algorithm and the multikernel adaptive filtering (MKAF) algorithm based on a Bayesian framework. The OAMP module estimates the APS from the uplink (UL) CCM regardless of its structural characteristics, whereas the MKAF module refines the APS estimation by leveraging its structural characteristics. These two modules operate iteratively, progressively improving the accuracy of the DL CCM estimation. Simulation results demonstrate that the proposed algorithm noticeably enhances the estimation performance and exhibits strong adaptability to diverse APS distributions and propagation environments, offering a novel approach for the DL CCM estimation in massive MIMO FDD systems. Full article

In this paper, we first introduced asymmetric coupled lines (ACLs) into both the transmission path and isolation path in traditional in-phase Gysel power dividers and proposed the single-resistor asymmetric coupled line in-phase Gysel power dividers (ACPDs). Utilizing the decoupled branch-line model of ACLs, a generalized design approach for ACPDs with arbitrary terminal real impedances and arbitrary power division ratio was innovatively proposed. Design formulas relating terminal real impedances, power division ratio, and image impedances of ACLs, for simultaneously satisfying the perfect port isolation and match conditions, are presented. ACPDs achieved a large in-phase power division ratio of 100:1 (20 dB) and offered significant advantages, including impedance transformation, high design freedom, and miniaturization. To automatically determine accurate initial values of geometric parameters for ACLs, a solution software based on MATLAB-HFSS co-simulation and multi-layer perception neural networks was developed, significantly reducing subsequent optimization iterations. To verify the proposed analysis theory and design approach, three ACPDs with different power division ratios of 1:1 (3 dB), 10:1 (10 dB), and 100:1 (20 dB) were implemented. Comparisons of the measured and simulated results showed great accordance, and the three ACPDs achieved good frequency bandwidth, high isolation, excellent port match, and compact size. Full article

In this paper, an adaptive frequency-domain block equalizer (FDBE) implementing the adaptive moment estimation (Adam) algorithm is proposed for mode-division multiplexing (MDM) optical fiber communication systems. By packing all frequency components into frequency-dependent blocks of a specified size $B$, we define an adaptive equalization matrix to simultaneously compensate for multiple frequency components at each block, which is computed iteratively using the Adam, recursive least squares (RLS) and least mean squares (LMS) algorithms. Simulations show that the proposed FDBE using the Adam algorithm outperforms those using the LMS and RLS algorithms in terms of adaptation speed and symbol error rate (SER) performance. The FDBE using the Adam algorithm with $B=1$ has the fastest adaption time, requiring about $n_{tr}=100$ and $n_{tr}=900$ less training blocks than the RLS algorithm at the SER of $3.8\times {10}^{-3}$ for the accumulated mode-dependent loss (MDL) of $\xi =1 \mathrm{d}$B and $\xi =5 \mathrm{d}$B, respectively. The Adam algorithm with $B=16$ and $B=8$ has $0.4 \mathrm{d}$B and $0.3 \mathrm{d}$B SNR better than the RLS algorithm with $B=4$ for MDL and $\xi =1 \mathrm{d}$B and $\xi =55 \mathrm{d}$B, respectively. Full article

Target detection is a core function of integrated sensing and communication (ISAC) systems. The traditional likelihood ratio test (LRT) target detection algorithm performs inadequately under low signal-to-noise ratio (SNR) conditions, and the performance of mainstream orthogonal frequency division multiplexing (OFDM) waveforms declines sharply in high-speed scenarios. To address these issues, an information-theory-based orthogonal time frequency space (OTFS)-ISAC target detection processing framework is proposed. This framework adopts the OTFS waveform as its fundamental signal. The target detection is implemented through a relative entropy test (RET) comparing echo signals against target presence/absence hypotheses. Furthermore, to enhance the system’s target detection capability, the iterative OTFS-ISAC waveform design (I-OTFS-WD) method which maximizes the relative entropy is proposed. This method utilizes the minorization-maximization (MM) algorithm framework and semidefinite relaxation (SDR) technique to transform the non-convex optimization problem into an iterative convex optimization problem for resolution. The simulation results demonstrate that, under sufficient sample conditions, the RET algorithm achieves a 9.12-fold performance improvement over LRT in low-SNR scenarios; additionally, the optimized waveform reduces the sample requirements of the RET algorithm by 40%, further enhancing the target detection capability of the OTFS-ISAC system. Full article

Resources in deserts and sandy landscapes have potential for development, but existing surveys and sampling have not collected desert soil samples. As such, the geochemical background of these spaces remains unexplored due to the vastness and desolation of deserts. Therefore, researching the geochemical background values and geochemical baseline values of deserts is of long-term significance. Our research indicates that in addition to macrostructural environmental divisions, microelement geochemistry can also be used for geological unit zoning. In this paper, geochemical background and geochemical baseline values of 61 desert elements were calculated using the iterative method, frequency histograms method, and multifractal concentration-area method. It also analyzes the distribution characteristics of major, trace, and rare earth elements, and divides the 12 desert sand regions into different geochemical zones. This paper determines, for the first time, the geochemical background values of elements in Chinese deserts, filling the gap in the study of desert background values. By combining machine learning methods, different deserts have been divided into three geochemical zones. This research will greatly enhance our ability to interpret the geochemical distribution and evolutionary patterns of desert elements in China, and it has important scientific significance and practical value for desert research. Full article

In 2023, we proposed the modified delay and Doppler profiler (mDDP) as an inter-carrier interference (ICI) countermeasure for underwater acoustic orthogonal frequency division multiplexing (OFDM) mobile communications in a multipath environment. However, the performance improvement in the computer simulation and pool experiments was not significant. In a subsequent study, the accuracy of the channel transfer function (CTF), which is the input for the mDDP channel parameter estimation, was considered insufficient. Then a sequential ICI canceling mDDP was devised. This paper presents simulations of underwater OFDM communications using an iterative one- to three-step mDDP. The non-reflective pool experiment conditions are a two-wave multipath environment where the receiving transducer moves at a speed of 0.25 m/s and is subjected to a Doppler shift in the opposite direction. As NumCOL, the number of taps in the multitap equalizer which removes ICI, was increased, the bit error rate (BER) of 0.0526661 at NumCOL = 1 was significantly reduced by a factor of approximately 45 to a BER of 0.0011655 at NumCOL = 51 for the sequential ICI canceling mDDP. Full article

Proper timing synchronization is important when data from sensors are acquired by different devices. This paper proposes a simple but effective solution for System on Chip (SoC) architectures that integrates a general-purpose Field Programmable Gate Array (FPGA) with a CPU. The proposed approach relies on a network synchronization protocol implemented in software, such as Network Time Protocol (NTP) or Precision Time Protocol (PTP), and uses the FPGA to generate a clock reference that is maintained in step with the synchronized system clock. The clock generated by the FPGA is obtained from the FPGA oscillator via appropriate fractional clock division. Clock drift is avoided via a software program that periodically compares the FPGA and the system counters, respectively, and adjusts the fractional clock divider in order to slightly adjust the FPGA clock frequency using a Proportional Integral controller. A specific implementation is presented on the RedPitaya platform, generating a 1 MHz clock in step with the NTP synchronized system clock. The presented system has been used in a distributed data acquisition system for fast transient recording in the neutral beam test facility for the ITER nuclear fusion experiment. Full article