Search Results (329)

We report a low-temperature plasma–liquid synthesis of crystalline β-Ga₂O₃ nanoparticles directly from aqueous solution. Pulsed discharge plasma bubbles generate reactive species that drive in situ dehydration and crystallization, bypassing the high-temperature calcination required by conventional methods. By varying the carrier gas, we tune morphology from uniform nanorice structures (He, Ar, and N₂) to amorphous microspheres (O₂ and air), revealing how plasma composition governs interfacial hydroxyl radical chemistry and growth kinetics. This approach demonstrates that localized plasma heating and reactive-species flux can achieve phase-selective oxide crystallization under ambient conditions, establishing plasma bubble reactors as a broadly applicable, low-temperature route for direct aqueous synthesis of crystalline wide-bandgap oxides that bridge solution chemistry and plasma nanomaterials design. Full article

An Al₂O₃/AlN stack deposited via Atomic Layer Deposition (ALD) methods as a gate insulator for silicon carbide (4H-SiC) has been investigated, focusing on the effects of different Al₂O₃ deposition processes on the nitride layer. In particular, dielectric stacks, consisting of a 10 nm AlN interface (001)-oriented layer directly grown on a 4H–SiC substrate and in 20 nm of additional amorphous Al₂O₃ layers were synthesized in sequential deposition runs by thermal ALD (T-ALD) or plasma-enhanced ALD (PEALD) methods. The evolution of the phenomena occurring at the Al₂O₃/AlN interfaces has been established by in situ ellipsometry measurements. Strong effects of the oxygen plasma because of the O-Al-N bond formation have been clearly observed and corroborated by ex situ structural and electrical characterizations, especially in the case of the plasma-enhanced Al₂O₃ process. In particular, the Al₂O₃/AlN bilayer grown by the Al₂O₃ T-ALD method exhibited good insulating behavior and an 8.7-high dielectric constant was measured. By contrast, the Al₂O₃/AlN bilayer grown by the Al₂O₃ PEALD method demonstrated poor insulating properties. Full article

The present study addresses the fabrication of porous gyroid architectures by additive manufacturing from preceramic polymer feedstocks. Photocurable emulsions were engineered by combining a silicone powder with acrylate monomers and dispersing an emulsified secondary phase of calcium nitrate. The formulations showed light-curing behaviour compatible with digital light processing vat photopolymerization (DLP-VPP), enabling high-fidelity replication of triply periodic minimal surface (TPMS) gyroids (designed porosity: 85 vol.%). After pyrolysis in nitrogen at 700 °C, the lattices converted into CaO–SiO₂-derived amorphous matrices embedding an in situ turbostratic/pyrolytic carbon fraction, as suggested by the photothermal response and preliminary impedance behaviour, although the latter was measured in liquid electrolyte and therefore does not isolate electronic transport. To improve robustness during polymer-to-ceramic conversion, pharmaceutical borosilicate waste glass (BASG) was added as a passive filler (30–70 wt.%). The waste-glass phase acts as a passive filler that improves processing robustness and can mitigate shrinkage-induced damage during pyrolysis, while remaining electrically insulating (dielectric) and therefore not directly contributing to electronic conduction. The resulting structures combine high surface-to-volume ratio, controlled open porosity, and structural integrity with electrochemical responsiveness under the adopted test conditions, making them promising architected platforms for electrochemical components where interconnected porosity is advantageous. Full article

To elucidate the corrosion behavior of Ti-based metallic glass composites in chloride-containing environments, this study investigates the corrosion resistance of an in situ dendritic Ti₄₈Zr₂₀Nb₁₂Cu₅Be₁₅ metallic glass composite across varying NaCl concentrations and temperatures. The microstructure, surface film composition, and corrosion characteristics were characterized using XRD, SEM, TEM, EDS, XPS, and electrochemical measurements. Results indicate that the alloy consists of a β-Ti(Zr, Nb) dendritic phase embedded in an amorphous matrix. Both increasing NaCl concentration and rising temperature lead to an increase in corrosion current density and a reduction in the capacitive loop radius, signaling a decline in corrosion resistance. The degradation is primarily characterized by localized corrosion and the selective dissolution of the amorphous matrix, which leaves the dendritic phase increasingly prominent. Following polarization, a multi-component oxide film, dominated by TiO₂, ZrO₂, and Nb₂O₅, develops as a protective layer on the alloy surface. However, higher Cl⁻ concentrations and temperatures destabilize this passive film, accelerating matrix dissolution and compromising the material’s overall protective performance. Full article

Although amorphous calcium phosphate (ACP) has been extensively employed as a biomaterial in dental and orthopedic fields, its exploration for environmental applications—particularly in potentially toxic element remediation—remains notably limited in the scientific literature. This study reports the rational design of a multifunctional adsorbent by integrating sodium citrate-stabilized ACP (Cit-ACP) nanoparticles into calcium-crosslinked sodium alginate (SA) hydrogel beads for selective Cu²⁺ sequestration from aqueous systems. Comprehensive sorption assessments revealed that equilibrium uptake aligned with the Freundlich isotherm (indicating heterogeneous surface interactions), while kinetic profiles adhered to pseudo-second-order behavior, characteristic of chemisorption-driven processes. Under optimized operational parameters (pH 5.0, 45 °C), the Cit-ACP/SA composite attained an exceptional maximum adsorption amount of 307.76 mg/g. Thermodynamic analysis further confirmed the spontaneity (ΔG° < 0) and endothermic nature (ΔH° > 0) of the process. Multi-technique characterization (XPS, FTIR, XRD, pH trajectory) elucidated a dual-mode adsorption mechanism: (i) ion exchange between aqueous Cu²⁺ and structural Ca²⁺ within both the alginate matrix and ACP framework; and (ii) in situ surface precipitation yielding copper-substituted hydroxyapatite. Owing to its facile aqueous-phase synthesis, superior adsorption performance, biodegradability, macroscopic bead morphology enabling rapid separation, and robust selectivity in complex matrices, the Cit-ACP/SA composite presents a sustainable, scalable, and eco-compatible platform for practical remediation of copper-contaminated wastewater. Full article

The corrosion behavior and time-dependent mechanism of 22MnB5 steel featuring a thinned Al-Si coating (60 g/m²) were systematically investigated in a chloride ion wet–dry cyclic environment, motivated by the demand for thinning and toughening development of aluminum-silicon coatings. A periodic immersion accelerated corrosion test using 3.5% NaCl solution was conducted, together with macro/microscopic morphology observation (SEM/EDS), phase analysis (XRD, FTIR), and electrochemical measurements (polarization curves, EIS). The Al-Si coated steel was studied over corrosion periods of 1, 8, 10, and 20 days to elucidate its corrosion behavior, interfacial evolution, and failure mechanism. The results indicated that the corrosion process exhibited a three-stage evolution: stable protection, rapid failure, and dynamic equilibrium. At the initial stage (1 day), a dense Al₂O₃ passive film formed on the coating surface, providing excellent substrate protection, with a corrosion current density of only 1.77 µA/cm² and a maximum charge-transfer resistance (R₂) of 652 Ω·cm². In the middle stage (8 days), Cl⁻ permeated through the cracked film, triggering selective dissolution of Al, while Si was enriched in situ to form a porous residual layer; the corrosion current density (I_corr) sharply increased to 13.25 µA/cm², and R₂ dropped to its minimum of 156.6 Ω·cm². Corrosion products at this stage were mainly Al₂O₃ and SiO₂, accompanied by small amounts of iron oxyhydroxides and hydroxides, and local coating failure began to appear. During the later stage (10–20 days), the corrosion products evolved into γ-FeOOH, α-FeOOH, and Fe₂O₃, which, together with an amorphous SiO₂ gel network enriched at the interface, formed a dual-layer composite rust layer. R2 consequently recovered from 156.6 Ω·cm² at 8 days to 424 Ω·cm² at 20 days, indicating a reduced corrosion rate and entry into a stable inhibition stage. The critical failure mechanism is that Cl⁻ preferentially penetrates the surface of the Al₂O₃ passive film, disrupting the metastable state of the coating and thereby creating pathways for corrosive media intrusion. The findings of this study can provide technical support for the safe application of such as-received coatings in non-load-bearing components with heat and corrosion resistance requirements. Full article

Nanotextured thin film metallic glasses (TFMGs) have emerged as promising antimicrobial coatings for biomedical applications; however, systematic comparisons across compositionally distinct Ti- and Zr-based systems, as well as their early-stage bactericidal mechanisms, remain limited. Here, we show, for the first time, a comparative, compositionally resolved correlation linking alloy chemistry, nanotexture, and bactericidal mechanisms across polymorphic TFMGs. Three co-sputtered biocompatible coatings (Ti₄₇Fe₄₁Cu₁₂, Zr₇₁Fe₃Al₂₆, and Zr₅₈W₃₁Cu₁₁) were deposited on medical-grade titanium and stainless steel (SS316L) via magnetron co-sputtering, producing uniform amorphous films (190–298 nm) with nanoscale roughness of 1.6 ± 0.05 to 8.1 ± 0.05 nm. Surface wettability spanned hydrophilic (71.1 ± 5.6°) to hydrophobic (106.5 ± 3.5°), modulating bacterial interactions. Antimicrobial performance against Pseudomonas aeruginosa was evaluated using live/dead fluorescence imaging, quantitative image analysis, and electron microscopy after 2–4 h incubation. All coatings reduced bacterial adhesion and viability relative to bare substrates, with Zr₅₈W₃₁Cu₁₁ achieving >60% reduction in surface-associated bacterial coverage. Time-resolved analysis revealed a rapid transition to predominantly non-viable populations on coated surfaces, in contrast to sustained viability on controls. Mechanistically, bactericidal activity arises from the synergistic coupling of nanotopography-induced membrane stress, wettability-governed adhesion energetics, and in situ formation of CuO, Fe₂O₃, WO₃, and ZrO₂ oxides that promote electrostatic interactions and proposed reactive oxygen species generation, driving oxidative membrane damage. These results establish a scalable design framework for TFMGs, while highlighting the need for long-term biofilm and electrochemical validation. Full article

A layered bimetallic CoMo-LDH precursor was prepared on nickel foam via a hydrothermal method, and a 3D hierarchical flower-like nanosheet CoMoP/NF electrocatalyst with a crystalline–amorphous heterostructure was constructed in situ through low-temperature phosphidation. The water electrolysis performance was optimized by adjusting the Co/Mo molar ratio. The 3D hierarchical porous structure provides a large specific surface area and abundant active sites, and Mo doping effectively modulates the electronic structure. The catalyst exhibits superior HER performance with overpotentials of only 37 mV and 65 mV at 10 mA·cm⁻² in acidic and alkaline media and shows a lower HER overpotential than commercial Pt/C at current densities above 426 mA·cm⁻² in acidic conditions. Meanwhile, this catalyst delivers an OER overpotential of 729 mV at 500 mA·cm⁻² in alkaline media and can operate stably for 50 h. The assembled two-electrode overall water splitting cell only requires 1.42 V at 10 mA·cm⁻², outperforming Pt/CǁRuO₂ (1.52 V). This work offers a promising strategy for designing low-cost and high-efficiency overall water splitting electrocatalysts for high-current-density applications. Full article

The electrolytic aluminum industry is facing severe challenges, such as excessive carbon consumption, resulting in more cost and environmental pollution due to the oxidation of carbon anodes. The isothermal oxidation resistance of B₄C-SiO₂-Albite (BSA) composite coating influenced by the in situ formation behavior and self-healing ability of the borosilicate glass at 1173 K was investigated through XRD, TG-DSC, Raman, FTIR spectroscopy, and SEM/EDS in this paper. The results show that the composite coating with 20 wt% B₄C has a relatively low mass gain rate of −0.082% after 24 h at 1173 K. It depends on the in situ formation of the amorphous borosilicate phase layer that can effectively protect the carbon anode from oxidation, which depends on the content of B₄C. The amorphous borosilicate glass forms from the reaction between the SiO₂ and the B₂O_3, from the oxidation of B₄C during exposure. More B₄C promotes the formation and volatilization of B₂O₃, which improves the viscosity and stability of the borosilicate glass by changing the glass network coupled with Na⁺ and Al³⁺ from Albite. It is a feasible strategy for designing durable coatings with appropriate B₄C addition for high-temperature applications. Full article

Efficient, low-cost catalysts are required for on-demand H₂ generation from chemical hydrides. This study utilized piezoelectric poly(vinylidene fluoride-co-hexafluoropropylene) (PVDF-HFP) nanofibers (NFs) as a support to encapsulate bimetallic Co–Mo nanoparticles (NPs) for H₂ production via sodium borohydride (SBH) methanolysis. The PVDF-HFP membranes were synthesized through electrospinning, followed by in situ SBH reduction, which resulted in the uniform dispersion of amorphous Co–Mo NPs within the nanofibrous matrix. The optimized CoMo-0.2@PVDF-HFP membrane exhibited a hydrogen generation rate (HGR) of 1.9 × 10³ mL·min⁻¹·g⁻¹ (Co) at 298 K, indicating a 3.6-fold improvement relative to monometallic Co. Kinetic studies showed a nearly first-order relationship with catalyst dose and a nearly zero-order relationship with respect to SBH concentration, suggesting kinetics controlled by surface saturation. The activation energy (E_a) was determined to be 14.03 kJ·mol⁻¹. Moreover, the catalyst maintained over 80% of its original activity after five cycles. This enhanced performance is attributed to the combined effects of Co and Mo, the amorphous nature of the active sites, and the piezoelectric polarization of PVDF-HFP during mechanical stirring, which together improve charge transfer and reduce NP agglomeration. Full article

The large-scale generation of waste graphite not only poses environmental challenges but also provides an opportunity for resource recovery. This study proposes a sustainable strategy that utilizes the graphite cutting waste produced during the production of large graphite electrodes through chemical intercalation, microwave-assisted expansion, and in situ urea nitrogen doping techniques to prepare nitrogen-containing micro-expanded graphite (NMG) composite materials. Structural analysis reveals that the nitrogen-doped amorphous carbon layer formed on the expanded graphite (EG) matrix effectively suppresses excessive expansion while preserving its typical worm-like interlayer morphology and porous structure. XPS confirms successful nitrogen doping with predominant pyridinic-N configuration, introducing abundant defect sites and enhancing lithiophilicity. As an anode for LIBs, NMG delivers an exceptional initial discharge capacity of 1907.5 mAh g⁻¹ at 20 mA g⁻¹ and maintains 798.2 mAh g⁻¹ after 50 cycles, nearly twice that of purified waste graphite (G). Remarkably, after 1000 cycles at 1 A g⁻¹, it retains 650.4 mAh g⁻¹ with 89.9% capacity retention, indicating an electrochemical activation process. Kinetic analysis reveals that the superior performance originates from synergistic diffusion-controlled intercalation and surface-dominated pseudocapacitance, with nitrogen-doped defect sites and hierarchical pore architecture promoting rapid ion/electron transport and surface faradaic reactions. This work demonstrates a viable pathway for value-added upcycling of waste graphite while providing insights into designing high-performance anodes through integrated defect engineering and heteroatom doping. Full article

This study explores the effects of sputtering pressure and power on FeCoNi high-entropy alloy films prepared by DC magnetron sputtering, focusing on microstructure, surface morphology, and static/high-frequency magnetic properties. In situ Lorentz TEM (LZ-TEM) was used to directly observe magnetic domain evolution. Results show that low sputtering pressure (1 mTorr) promotes strong FCC (111) crystallization, and smooth and dense surfaces. Increasing pressure leads to amorphization, higher roughness, and degraded magnetic performance. Under optimized pressure, 100 W sputtering power yields the best crystallinity, the smoothest surface, and optimal soft magnetic properties, including high remanence ratio, low coercivity, and clear ferromagnetic resonance in the 2–7.5 GHz range. The optimal parameters are confirmed as 1 mTorr and 100 W, producing uniform nanocrystalline FeCoNi films. In situ LZ-TEM reveals river-like domain walls, vortex–antivortex structures, and uniform magnetic moment precession, indicating weak domain pinning and excellent high-frequency magnetization consistency. This study provides experimental and theoretical support for the controllable fabrication of high-performance FeCoNi soft magnetic films for high-frequency devices. Full article

In this work, a hybrid polymer electrolyte integrating single- and dual-ion conducting systems was developed for lithium-ion batteries using bio-based materials, namely oleic-acid derivatives and epoxidized soybean oil, through an in situ polymerization process. The fixed FSI anions in LiEFSOA enhance the selectivity of Li⁺ transport, while the cross-linked network formed by ESO provides mechanical stability, and the LiFSI incorporated into the polymer matrix helps maintain sufficient overall ionic conductivity. In addition, the long C18 oleic chains increase the internal free volume of the matrix, thereby improving segmental mobility within the amorphous phase. The in situ polymerization inside the cell causes intimate interfacial contact between the electrode and electrolyte, achieving an ionic conductivity of 1.05 × 10⁻⁴ S cm⁻¹ at 30 °C. Electrochemical evaluation using LiFePO₄/FSOA-2/Li cells shows an initial discharge capacity of 149.09 mAh g⁻¹ and a capacity retention of 81.09% after 100 cycles, and the average coulombic efficiency was 99.62%, demonstrating that the designed FSOA electrolyte exhibits stable cycling performance and competitive capacity. Overall, the combination of eco-friendly materials and a hybrid ion transport strategy provides a promising platform for developing sustainable and high-performance polymer electrolytes for lithium-ion batteries. Full article

Mechanical properties of lead-free hybrid perovskites have attracted growing interest because of their significance in future eco-friendly optoelectronic applications. However, there are very limited studies about the intrinsic elastic properties and high-pressure structural evolution of hybrid perovskites, and the fundamental structure–mechanical property relationships are insufficiently understood. Here, we report the elastic behavior of a three-dimensional (3D) hybrid organic–inorganic perovskite, (DABCO)RbBr₃ (DABCO = triethylenediammonium), and confirm the processability through processing with chiral metasurfaces and the generation of circular dichroism. Our in situ high-pressure synchrotron X-ray diffraction experiments demonstrate that this crystal does not start to amorphize until 2.3 GPa. Density functional theory calculations reveal that its E, G and v range between 20.73 and 27.93 GPa, 8.21 and 11.62 GPa and 0.18–0.39, respectively. Additionally, due to the low elastic moduli and polar crystal structure, we fabricate a device of (DABCO)RbBr₃ composite film, which shows favorable performance for piezoelectric energy harvesting. This work utilizes (DABCO)RbBr₃ to open up new avenues for applications in manufacturing and energy harvesting. Full article

Background/Objectives: The formulation development of Isotretinoin (ISN) is limited by its solubility and stability issues. This study aimed to characterise the BCS class II drug ISN, particularly the possible different solid state and formulate amorphous solid dispersion aiming for a supersaturation state. Methods: ISN’s physical states are investigated in its raw form, quench-cooled form, physical mixture with the polymer and corresponding solid dispersion form. Quench-cooled ISN was prepared in situ using DSC. Carrier stabilisation of ISN was attempted using the solid dispersion technique. Hereby, the solid dispersion of drug-polymer PVPVA at a ratio of 1:3 was prepared using the solvent evaporation method. Solid dispersion, physical mixture and raw ISN were characterised for the saturated solubility. Physical characterisation of the samples was performed using DSC, ATR-FTIR and a light microscope. Results: Two polymorphs of ISN (forms I and II) were found in the raw ISN, with form II being thermodynamically more stable. ISN possesses strong crystallinity and resistance to amorphisation under the applied quench-cooling condition without the presence of a carrier system. The conjugated polyene structure in ISN contributes to the polymorphic transformation and isomerisation. The incorporation of PVPVA in the solid dispersion system successfully improved the water solubility (sixfold) of ISN despite a combination of crystalline and amorphous components being present in the system. Conclusions: ISN is a class II drug crystal molecule. Taking advantage of solubility and possibility in the polymorphic transformation of ISN in a binary system, we concluded that ISN could potentially be formulated into its corresponding crystalline solid dispersion form. Full article