Search Results (75)

Replacing artificial dyes with natural pigments in foods, especially carotenoids, has proven to be technologically feasible. This study developed a high-performance pitanga carotenoid extraction process using ionic liquids (ILs) and a factorial design to identify a potential substitute for artificial azo dyes, specifically Allura Red AC and Sunset Yellow FCF. 1-Hexyl-3-methyl-imidazolium chloride [C6mim]Cl was the most efficient IL. The optimized process conditions included a solid–liquid ratio R(S/L) of 1:10 m/m, an IL to ethanol co-solvent ratio R(IL/E) of 1:1 m/m, ultrasound power of 350 W, and six extraction cycles of 7 min each. These conditions yielded a total carotenoid content of 100.40 ± 3.71 μg/g (dry matter), demonstrating effective pigment recovery and a concentration suitable for practical use as a natural colorant alternative to synthetic azo dyes. The reuse of ILs and carotenoid purification were achieved through solid-phase extraction (SPE) using XAD-7HXP adsorbent, resulting in recovery rates of 89.2–76.2% for [C6mim]Cl and 108.9–23.2% for carotenoids. The major carotenoids identified were all-trans-β-cryptoxanthin, all-trans-rubixanthin, and all-trans-lycopene, whose combined presence contributed to a yellowish-orange hue similar to that of Sunset Yellow FCF, as confirmed by CIELAB parameters. Additionally, the [C6mim]Cl carotenoid extract exhibited high antioxidant activity, with an antioxidant capacity of 23.54 µmol of α-tocopherol equivalent. Full article

In this study, the task of integrating capture and conversion of CO₂ into a single material platform is realized by developing bifunctional membranes based on polymer ionic liquids (PILs). The novelty of this work lies in the fabrication and comprehensive evaluation of PIL-based membrane materials that combine catalytic activity toward CO₂ conversion with gas separation performance within one material system. In contrast to most previously reported imidazolium-based PILs, which have mainly been considered either as catalysts or as membrane materials, the present approach focuses on their dual functionality under both catalytic and gas transport conditions. A series of imidazolium-based PILs, including homopolymers and block copolymers with polystyrene, were synthesized. The materials were characterized to determine their catalytic activity during the cycloaddition of CO₂ to epichlorohydrin and to determine their gas transport properties using pure gases (N₂, O₂, CO₂) and a simulated dry flue gas mixture; membrane morphology was studied by scanning electron microscopy. Block copolymers exhibited higher catalytic conversions (up to 82.7%) than homopolymers, with selectivities above 93%. Chloride-containing block copolymers gave the best combination of CO₂ permeability (up to 7.5 Barrer) and CO₂/N₂ selectivity (18–22) under mixed-gas conditions. Iodide-containing analogs demonstrated higher selectivity (up to 30) but lower CO₂ permeability. Morphological analysis confirmed the presence of dense, defect-free structures in materials with the chloride anion, while materials with the iodide anion showed increased free volume and microheterogeneity. These results indicate that by altering the polymer and anion architecture, PIL-based membranes can effectively combine catalytic activity with selective CO₂ transport, providing a promising avenue for enhancing carbon capture and utilization processes. Full article

This study explores the influence of anion hydrogen-bond basicity, quantified by the Kamlet–Taft β parameter, on cellulose dissolution in imidazolium-based ionic liquids (ILs). A series of ILs sharing the common cation 1-benzyl-3-methylimidazolium were synthesized with varying anions, including chloride, acetate, formate, methoxyacetate, and methylphosphonate. The hydrogen-bond accepting ability (β) of each IL was experimentally determined and correlated with cellulose dissolution performance. Dissolution capability was evaluated by solubilizing 5 wt% cotton cellulose at 90 °C and monitoring under polarized light microscopy. Among the studied systems, 1-benzyl-3-methylimidazolium acetate (β = 1.01) demonstrated the highest dissolution efficiency, highlighting the critical role of strong hydrogen-bond basicity in disrupting the cellulose hydrogen-bonding network. To support the experimental observations, COSMO-RS simulations were conducted to probe the molecular-level interactions between anions and cellulose. Parameters such as anion size, theoretical density, viscosity, and surface charge density distribution were analyzed to elucidate their contributions to dissolution behavior. The regenerated cellulose was further characterized using scanning electron microscopy (SEM) and Fourier transform infrared (FTIR) spectroscopy. Full article

Polyphenols are structurally diverse plant secondary metabolites with broad biological activities and growing applications across the food, health, and materials sectors. Conventional extraction based on organic solvents (e.g., methanol, ethanol) is often energy-intensive, inefficient, and environmentally burdensome. Ionic liquids (ILs) and deep eutectic solvents (DESs) have therefore emerged as greener alternatives for polyphenol extraction. This review evaluates recent advances in solvent design, extraction performance, and process sustainability. Imidazolium-based ILs frequently achieve high yields and selectivity, particularly when coupled with ultrasound or microwave-assisted extraction, but high cost, synthetic complexity, viscosity-related constraints, and potential toxicity hinder scaleup. By contrast, DESs—especially those derived from choline chloride or lactic acid—are easier to prepare, less costly, and more compatible with industrial implementation, with efficiency enhanced by tailoring hydrogen bond networks, water content, and process intensification. Critical downstream challenges persist for both solvent classes, notably in extract purification and solvent recovery due to low volatility; approaches such as resin adsorption, antisolvent precipitation, and direct formulation have been explored. Overall, ILs and DESs represent compelling alternatives to conventional solvents, and future progress will depend on integrated extraction–recovery strategies, systematic solvent selection, and validation under scalable, sustainable processing conditions. Full article

This study reports the synthesis and catalytic evaluation of a series of imidazolium-based polymeric ionic liquids (PILs) for the cycloaddition of CO₂ to epichlorohydrin (ECH). The synthesized catalysts include homopolymers, poly(3-hydroxyethyl-1-vinylimidazole chloride) (p[HVIm][Cl]) and poly(3-carboxymethyl-1-vinylimidazole chloride) (p[CMVIm][Cl]), and their block copolymers with polystyrene, synthesized for the first time, pS-b-p[HVIm][Cl] and pS-b-p[CMVIm][Cl]. Structural characterization by NMR, IR spectroscopy, and gel permeation chromatography confirmed the successful synthesis. The block copolymers exhibited a low polydispersity index (PDI 1.1–1.2), which is indicative of homogeneous chain lengths and the propensity to form ordered nanostructures, whereas the homopolymers showed higher PDI (2.4–2.9). Catalytic testing at 90 °C and 1 MPa CO₂ for 4 h revealed a clear activity trend: p[CMVIm][Cl] < p[HVIm][Cl] < pS-b-p[CMVIm][Cl] < pS-b-p[HVIm][Cl], with conversions exceeding 75% for all catalysts and a maximum of 82.69% for pS-b-p[HVIm][Cl]. These results demonstrate that the catalytic performance of PILs is governed by a synergistic interplay between the local chemical functionality of the ionic moiety and the overall polymer architecture. Based on these results, the synthesized polymeric ionic liquids, particularly pS-b-p[HVIm][Cl], demonstrate strong potential for creating multifunctional materials. Their ability to self-assemble into ordered nanostructures with distinct hydrophobic and hydrophilic domains provides a foundational architecture for combined gas separation and catalysis. The observed “micellar catalytic effect”, which enhances local reagent concentration near active sites, could be leveraged in a membrane reactor to simultaneously capture and convert CO₂ directly within the membrane. This integrated “separation–reaction” approach represents a promising strategy for advancing circular carbon economy technologies. Full article

Imidazolium-based ionic liquids bearing a homologous series of oxychlorine anions—1-butyl-3-methylimidazolium chlorite, chlorate, and perchlorate—were synthesized and characterized to relate anion oxygenation to density, thermal expansivity, viscosity, electrical and molar conductivity, ionicity, and antimicrobial performance. Temperature-dependent measurements were carried out from 293.15 to 323.15 K: density and viscosity were recorded and modeled to obtain thermal expansion coefficients; electrical and molar conductivities were measured under identical conditions; and activation parameters were extracted by Arrhenius analysis for viscous flow and for conductivity. Ionicity was assessed from Walden plots and quantified by vertical deviation from the potassium-chloride reference (Angell approach). Complementary DFT calculations provided optimized ion-pair geometries, noncovalent contact patterns, molecular electrostatic potential maps, and frontier-orbital descriptors. In silico ADMET properties were computed to contextualize pharmacokinetic and safety flags. Antimicrobial activity was evaluated by broth microdilution against Escherichia coli, Staphylococcus aureus, Bacillus cereus, and Candida quilliermondii; [Bmim]Cl was included as a comparator to isolate the effect of anion oxygenation. The combined experimental–computational workflow delineates how chlorite, chlorate, and perchlorate shape physicochemical behavior, ionicity, and bioactivity in [Bmim] ionic liquids, providing design guidance for future applications. Full article

Vanadium is a strategic metal with critical applications in steel alloys, aerospace, chemical catalysis, and energy storage. However, conventional extraction methods such as high-temperature salt roasting are energy-intensive and environmentally challenging. This study investigated the extraction of V, Ti, and Fe from titanomagnetite ore using aqueous solutions of two ionic liquids (IL), 1-butyl-3-imidazolium hydrogen sulphate ([Bmim][HSO₄], and 1-butyl-3-methylimidazolium hexafluorophosphate [Bmim][PF₆]) as well as two deep eutectic solvents (DESs) (choline chloride:oxalic acid and choline chloride:succinic acid). Na₂CO₃ and Na₂SO₄ roasting were used as benchmarks for comparison purposes. Leaching was performed across a range of concentrations and temperatures, and metal recoveries were quantified by atomic absorption spectroscopy (AAS). Among all methods, ChCl:OA DES achieved the best leaching efficiencies of 97.6% for V, 76.1% for Ti, and 68.8% for Fe at 50% (v/v) and 100 °C, outperforming [Bmim][HSO₄] and conventional roasting. Kinetic analysis using the shrinking core model indicated that leaching is predominantly diffusion-controlled, with apparent activation energies of 35.1 kJ/mol for V, 28.3 kJ/mol for Ti, and 29.8 kJ/mol for Fe. The results demonstrate that ChCl:OA DES provides a low-temperature, biodegradable, and cost-effective approach for V, Ti and Fe extraction, offering a sustainable alternative to conventional salt roasting methods. Full article

A series of sulfur dissolving tetrathionate ionic liquids (ILs), featuring imidazolium and pyridinium cationic heads, have been prepared and characterized along with their chloride IL precursors. A novel synthetic approach for the preparation of the proposed tetrathionate ILs has been introduced and successfully tested in the current work, yielding the desired compounds in quantitative yield and high purity, offering a significant advancement over the traditional Volynskii–Smolyaninov reaction. The presented method addresses key challenges of the traditional approach, solving the issues deriving from the influence of the IL cation on the reaction outcome and the unpredictability of the formed polythionate species. The solubility of elemental sulfur in the considered tetrathionate ILs has been investigated at various temperatures, providing good preliminary evidence of the suitability of these ILs as convenient and effective sulfur solubilizing media readily available on the field in “sour” gas extraction plants. Furthermore, the use of ILs instead of traditional organic solvents in operative conditions represents a noteworthy safety improvement due to their lower flammability and volatility. Finally, interesting results were obtained studying binary mixtures of organic solvents and ILs, with cooperative effects or salting-out effects being observed in relation to the type of solvent used. Full article

Structure–property relationships in imidazolium-based hybrid Sb(III) chlorides provide critical guidance for designing high-performance materials. Three zero-dimensional metal halides, namely, [C₃mmim]₂SbCl₅ (1, [C₃mmim]⁺ = 1-propyl-2,3-dimethylimidazolium), [C₅mmim]₂SbCl₅ (2, [C₅mmim]⁺ = 1-pentyl-2,3-dimethylimidazolium), and [C₅mim]₂SbCl₅ (3, [C₅mim]⁺ = 1-pentyl-3-methylimidazolium), are synthesized by ionothermal methods. These compounds exhibit markedly distinctly photophysical properties at their optimal excitation wavelengths. Structural analyses reveal that elongated alkyl chains in compounds 2 and 3 increase Sb–Sb distances compared to that in 1, effectively isolating [SbCl₅]²⁻ units, suppressing inter-center energy transfer, and reducing non-radiative transitions, thereby enhancing the photoluminescence quantum yield (PLQY). Furthermore, methyl substitution at the C2-position of the imidazolium ring in compounds 1 and 2 induces asymmetric coordination environments around the [SbCl₅]²⁻ emission centers, leading to pronounced structural distortion. This distortion promotes non-radiative decay pathways and diminishes luminescent efficiency. Furthermore, temperature-dependent spectroscopy analysis and fitting of the Huang–Rhys factor (S) reveal significant electron–phonon coupling in compounds 1–3, which effectively promotes the formation of self-trapped excitons (STEs). However, compound 1 exhibits extremely high S, which significantly enhances phonon-mediated non-radiative decay and ultimately reduces its PLQY. Overall, compound 3 has the highest PLQYs. Full article

Aiming to obtain insight into the dynamic properties of ionogels, ¹H NMR relaxation experiments were performed for an ionogel composed of 1-butyl-3-methyl-imidazolium chloride [BMIM][Cl] and propylene carbonate. The experiments were conducted in the frequency range of 10 kHz to 20 MHz, spanning the temperature range of 273 K to 338 K. The data were analyzed in term s of a relaxation model including two relaxation contributions—one of them associated with anisotropic (two-dimensional) translation diffusion, the second one representing a power law dependence of spin-lattice relaxation rates on the resonance frequency. The power law relaxation term (characterized by a very low power law factor of about 0.1) was attributed to the collective dynamics of the partially immobilized propylene carbonate matrix, while the relaxation contribution associated with anisotropic translation diffusion was attributed to the movement of BMIM cations in the matrix; the translation diffusion coefficient was estimated as varying in the range of 10⁻¹³ m²/s–10⁻¹² m²/s. Moreover, other parameters were determined as a result of the analysis, such as the residence lifetime on the matrix surfaces. Subsequently, the temperature dependencies of the determined parameters were assessed. Full article

Strategic utilization of carbon dioxide as both a carbon mitigation tool and a sustainable C1 feedstock represents a pivotal pathway toward green chemistry. Although poly(ionic liquid)s (PILs) exhibit promise in CO₂ conversion, conventional divinylbenzene (DVB) cross-linked architectures are limited by reduced ionic density and limited accessibility of active sites. Herein, we reported a binuclear imidazolium-functionalized PIL catalyst (P-BVIMCl), synthesized through a simple self-polymerization process, derived from rationally designed ionic liquid monomers formed by quaternization of 1,4-bis(chloromethyl)benzene with N-vinylimidazole. The dual active sites in P-BVIMCl-quaternary ammonium cation (N⁺) and nucleophilic chloride anion (Cl⁻) synergistically enhanced CO₂ adsorption/activation and epoxide ring-opening. Under optimal catalyst preparation conditions (100 °C, 24 h, water/ethanol = 1:3 (v/v), 10 wt% AIBN initiator) and reaction conditions (100 °C, 2.0 MPa CO₂, 10 mmol epichlorohydrin, 6.7 wt% catalyst loading, 3.0 h), P-BVIMCl catalyzed the synthesis of glycerol carbonate (GLC) with a yield of up to 93.4% and selectivity of 99.6%, maintaining activity close to 90% after five cycles. Systematic characterization and density functional theory (DFT) calculations confirmed the synergistic activation mechanism. This work established a paradigm for constructing high-ionic-density catalysts through molecular engineering, advancing the development of high-performance PILs for industrial CO₂ valorization. Full article

Understanding the interplay between the molecular structure of the ionic liquid (IL) subunit, the resulting nanostructure and ion transport in polymerized ionic liquids (PILs) is necessary for the realization of high-performance solid-state electrolytes required in various advanced applications. Herein, we present a detailed structural characterization of a recently synthesized series of acrylate-based PIL homopolymers and networks with imidazolium cations and chloride anions with varying alkyl spacer and terminal group lengths designed for organic solid-state batteries based on X-ray scattering. The impact of the concentrations of both the crosslinker and added tetrabutylammonium chloride (TBACl) conducting salt on the structural characteristics is also investigated. The results reveal that the length of both the spacer and terminal group influence the chain packing and, in turn, the nanophase segregation of the polar domains. Long spacers and terminal groups seem to induce denser polar aggregates sandwiched between more compact alkyl spacer and terminal group domains. However, the large inter-backbone spacing achieved seems to limit the ionic conductivity of these PILs. More importantly, our findings show that the previously reported general relationships between the ionic conductivity and the structural parameters of the nanostructure of PILs are not always attainable for different molecular structures of the IL side group. Full article

Multiple intermolecular H-bonding interactions play a pivotal role in determining the macroscopic state of ionic liquids (ILs). Hence, the relationship between the microscopic and the macroscopic properties is key for a rational design of new imidazolium ILs. In the present work, we investigated how the physicochemical property of hydroxyl-functionalized imidazolium chloride is connected to the molecular structure and intermolecular interactions. In the isolated ion pair, strong N-H···Cl H-bonding interactions are observed rather than H-bonding interactions at the acidic C₂-H site and alkyl-OH···Cl of the hydroxyl-functionalized imidazolium chloride. However, the N-H···Cl H-bonding interaction of the cation plays a significant role in ion-pair formations and polymeric clusters. For 3-(2-Hydroxy)-1H-imidazolium chloride (EtOHImCl), the oxygen atom (O) engages in two significant interactions within its homodimeric ion-pair cluster: N-H···O and alkyl OH···Cl. Vibrational spectroscopy and DFT calculations reveal that the chloride ion (Cl⁻) forms a hydrogen bond with the C2-H group via a C2-H···Cl interaction site. Natural Bond Orbital (NBO) analysis indicates that the O-H···Cl hydrogen-bonding interaction is crucial for the stability of the IL, with a second-order perturbation energy of approximately 133.8 kJ/mol. Additional computational studies using Atoms in Molecules (AIMs), non-covalent interaction (NCI) analysis, Electron Localization Function (ELF), and Localized Orbital Locator (LOL) provide significant insights into the properties and nature of non-covalent interactions in ILs. Ab initio molecular dynamics (AIMD) simulations of the IL demonstrate its stable states with relatively low energy values around −1680.6510 atomic units (a.u.) at both 100 fs and 400 fs due to O-H···Cl and C-H···Cl interactions. Full article

We present a novel approach to characterize and quantify microheterogeneity and microphase separation in computer simulations of complex liquid mixtures. Our post-processing method is based on local density fluctuations of the different constituents in sampling spheres of varying size. It can be easily applied to both molecular dynamics (MD) and Monte Carlo (MC) simulations, including periodic boundary conditions. Multidimensional correlation of the density distributions yields a clear picture of the domain formation due to the subtle balance of different interactions. We apply our approach to the example of force field molecular dynamics simulations of imidazolium-based ionic liquids with different side chain lengths at different temperatures, namely 1-ethyl-3-methylimidazolium chloride, 1-hexyl-3-methylimidazolium chloride, and 1-decyl-3-methylimidazolium chloride, which are known to form distinct liquid domains. We put the results into the context of existing microheterogeneity analyses and demonstrate the advantages and sensitivity of our novel method. Furthermore, we show how to estimate the configuration entropy from our analysis, and we investigate voids in the system. The analysis has been implemented into our program package TRAVIS and is thus available as free software. Full article

Stretchable ionogels, as soft ion-conducting materials, have generated significant interest. However, the integration of multiple functions into a single ionogel, including temperature tolerance, self-adhesiveness, and stability in diverse environments, remains a challenge. In this study, a new class of fluorine-containing ionogels was synthesized through photo-initiated copolymerization of fluorinated hexafluorobutyl methacrylate and butyl acrylate in a fluorinated ionic liquid 1-butyl-3-methyl imidazolium bis (trifluoromethylsulfonyl) imide. The resulting ionogels demonstrate good stretchability with a fracture strain of ~1300%. Owing to the advantages of the fluorinated network and the ionic liquid, the ionogels show excellent stability in air and vacuum, as well as in various solvent media such as water, sodium chloride solution, and hexane. Additionally, the ionogels display impressive wide temperature tolerance, functioning effectively within a wide temperature range from −60 to 350 °C. Moreover, due to their adhesive properties, the ionogels can be easily attached to various substrates, including plastic, rubber, steel, and glass. Sensors made of these ionogels reliably respond to repetitive tensile-release motion and finger bending in both air and underwater. These findings suggest that the developed ionogels hold great promise for application in wearable devices. Full article