Search Results (43)

This study utilizes a zero-dimensional, constant-pressure, perfectly stirred reactor (PSR) model within the Cantera framework to examine the combustion characteristics of hydrogen, methane, methanol, and propane, both singly and in hydrogen-enriched mixtures. The impact of the equivalence ratio (ϕ = 0.75, 1.0, 1.5), fuel composition, and residence duration on temperature increase, heat release, ignition delay, and emissions (NO_x and CO₂) is methodically assessed. The simulations are performed under steady-state settings to emulate the ignition and flame propagation processes within pre-chambers and primary combustion zones of internal combustion engines. The results demonstrate that hydrogen significantly improves combustion reactivity, decreasing ignition delay and increasing peak flame temperature, especially at short residence times. The incorporation of hydrogen into hydrocarbon fuels, such as methane and methanol, enhances ignition speed, improves thermal efficiency, and stabilizes lean combustion. Nevertheless, elevated hydrogen concentrations result in increased NO_x emissions, particularly at stoichiometric equivalence ratios, due to higher flame temperatures. The examination of fuel mixtures at varying hydrogen concentrations (10–50% by mole) indicates that thermal performance is optimal under stoichiometric settings and diminishes in both fuel-lean and fuel-rich environments. A thermodynamic model was created utilizing classical combustion theory to validate the heat release estimates based on Cantera. The model computes the heat release per unit volume (MJ/m³) by utilizing stoichiometric oxygen demand, nitrogen dilution, fuel mole fraction, and higher heating values (HHVs). The thermodynamic estimates—3.61 MJ/m³ for H₂–CH₃OH, 3.43 MJ/m³ for H₂–CH₄, and 3.35 MJ/m³ for H₂–C₃H₈—exhibit strong concordance with the Cantera results (2.82–3.02 MJ), thereby validating the physical consistency of the numerical methodology. This comparison substantiates the Cantera model for the precise simulation of hydrogen-blended combustion, endorsing its use in the design and development of advanced low-emission engines. Full article

Rapid and precise detection of hydrogen sulfide (H₂S) at trace levels is critical for industrial safety and environmental air quality monitoring, yet existing methods often struggle with cost, speed, or sensitivity. A cost-effective cavity ring-down spectroscopy (CRDS) analyzer is presented, incorporating a novel digital locking circuit for sequential laser-cavity mode matching. This system demonstrates rapid and precise hydrogen sulfide (H₂S) detection capability at parts-per-billion (ppb) concentration levels. Compared to traditional wavelength meters, our system delivers a 140-fold improvement in frequency interval precision (0.07 MHz, 0.027% relative uncertainty). Allan variance analysis under vacuum conditions demonstrates a sensitivity limit of 3 × 10⁻¹² cm⁻¹ at a 60-s averaging time. Validated through calibrated gas dilution tests, the analyzer detects a 4 ppb H₂S absorption signal with a signal-to-noise ratio (SNR) > 6, establishing a 2 ppb detection limit (3σ criterion). This innovative approach meets stringent industrial and environmental requirements, offering a significant advancement in trace gas-sensing technology. Full article

Aluminum nanoparticles (Al NPs) are interesting for energetic and plasmonic applications due to their enhanced size-dependent properties. Passivating the surface of these particles is necessary to avoid forming a native oxide layer, which can degrade energetic and optical characteristics. This work utilized a radiofrequency (RF)-driven capacitively coupled argon/hydrogen plasma to form surface-modified Al NPs from aluminum trichloride (AlCl₃) vapor and 5% silane in argon (dilute SiH₄). Varying the power and dilute SiH₄ flow rate in the afterglow of the plasma led to the formation of varying nanoparticle morphologies: Al–SiO₂ core–shell, Si–Al₂O₃ core–shell, and Al–Si Janus particles. Scanning transmission electron microscopy with a high-angle annular dark-field detector (STEM-HAADF) and energy-dispersive X-ray spectroscopy (EDS) were employed for characterization. The surfaces of the nanoparticles and sample composition were characterized and found to be sensitive to changes in RF power input and dilute SiH₄ flow rate. This work demonstrates a tunable range of Al–SiO₂ core–shell nanoparticles where the Al-to-Si ratio could be varied by changing the plasma parameters. Thermal analysis measurements performed on plasma-synthesized Al, crystalline Si, and Al–SiO₂ samples are compared to those from a commercially available 80 nm Al nanopowder. Core–shell particles exhibit an increase in oxidation temperature from 535 °C for Al to 585 °C for Al–SiO₂. This all-gas-phase synthesis approach offers a simple preparation method to produce high-purity heterostructured Al NPs. Full article

Hazardous substances such as hydrogen and chlorine are used in semiconductor manufacturing. When these gasses are discharged, they are mixed with outside air and are connected to a treatment facility through a duct inside a gas box. This study investigated an optimal exhaust design to prevent fire explosions and toxic exposure by optimizing the exhaust volume when hazardous substances leak from the gas box of semiconductor manufacturing equipment. In this study, carbon monoxide was used for modeling. A 75 mm duct was used, and the tracer gas was released into the gas box at 15.4 LPM. The concentrations were measured at nine points inside and outside the gas box. According to the test results, in an experiment designed with 0% air intake, the internal leakage concentration was measured to be more than 25% of the LEL (lower explosive limit) for 10 min when leakage occurred due to stagnant flow, and the outside toxicity concentration was also measured to be more than 50% of the TWA (time-weighted average) value. When the air intake ratio was designed to be 100%, there was a point on the outside that exceeded 50% of the TWA, confirming that excessive air intake could also cause gas to leak outside. Finally, when the intake ratio was designed to be 50% in both directions, it was confirmed that the airflow was maintained smoothly, and the hazardous gasses were safely diluted and discharged through the duct. This study was conducted to improve the safety of workers in the field in the event of leakage of flammable and toxic gasses by testing the location and area of the air intake hole in the gas box exhaust port. Through this effort, the aim is to present specific standards for gas box design and to assist in establishing a legal framework or standardized guidelines. Full article

Hydrogen is a well-known clean energy carrier with a high energetic yield. Its versatility allows it to be produced in diverse ways, including biologically. Specifically, dark fermentation takes advantage of organic wastes, such as agro-industrial residues, to obtain hydrogen. One of these harmful wastes that is poorly discharged into streams is sugarcane bagasse pentose liquor (SBPL). The present study aimed to investigate hydrogen generation from SBPL fermentation in batch reactors by applying different food/microorganism (2–10 F/M) and carbon/nitrogen (10–200 C/N) ratios under mesophilic and thermophilic conditions. Biohydrogen was produced in all pentose liquor experiments along with other soluble microbial products (SMPs): volatile fatty acids (VFAs) (at least 1.38 g L⁻¹ and 1.84 g L⁻¹ by the average of C/N and F/M conditions, respectively) and alcohols (at least 0.67 g L⁻¹ and 0.325 g L⁻¹ by the average of C/N and F/M conditions, respectively). Thermophilic pentose liquor reactors (t-PLRs) showed the highest H₂ production (H₂ maximum: 1.9 ± 0.06 L in 100 C/N) and hydrogen yield (HY) (1.9 ± 0.54 moles of H₂ moles of substrate⁻¹ in 2 F/M) when compared to mesophilic ones (m-PLRs). The main VFA produced was acetate (>0.85 g L⁻¹, considering the average of both nutritional conditions), especially through the butyrate pathway, which was the most common metabolic route of experimental essays. Considering the level of acid dilution used in the pretreatment of bagasse (H₂SO₄ (1%), 1.1 atm, 120 °C, 60 min), it is unlikely that toxic compounds such as furan derivatives, phenol-like substances (neither was measured), and acetate (<1.0 g L⁻¹) hinder the H₂ production in the pentose liquor reactors (PLRs). Sugarcane bagasse pentose liquor fermentation may become a suitable gateway to convert a highly polluting waste into a renewable feedstock through valuable hydrogen production. Full article

In this article we present the first investigation of the stable isotope composition of groundwater in Romania, East-Central Europe, with a focus on the karst areas. Our aim is twofold: (1) to provide a countrywide map with the distribution of stable oxygen and hydrogen isotope ratios in groundwater, and (2) to assess the recharge patterns of karst water. We collected more than 600 water samples from springs and wells across Romania for stable isotope analyses and monitored in detail the stable isotope composition of the waters as they pass through five cave systems. Our data show a spatial distribution of the stable isotope composition of the groundwater with low values in the mountainous area and high values in the surrounding lowlands and the central Transylvanian Depression. However, waters in karst areas induce departures from this distribution, resulting from the fast (hours to days) transfer of waters from high (ponor) to low (spring) altitudes. Water emerging from the karst springs has generally lower δ values than before sinking through the ponors, thus indicating a substantial contribution of winter recharge through diffuse infiltration and seepage. This contribution results in overall dilution of the water entering through ponors, likely resulting in changes in the chemical composition of the water and diluting potential pollutants. Our data call for careful separation between karst and non-karst spring/well waters, as indiscriminate common treatment might lead to erroneous interpretations. Full article

Layers of TiO₂ nanotubes formed by the anodization process represent an area of active research in the context of innovative energy conversion and storage systems. Titanium nanotubes (TNTs) have attracted attention because of their unique properties, especially their high surface-to-volume ratio, which makes them a desirable material for various technological applications. The anodization method is widely used to produce TNTs because of its simplicity and relative cheapness; the method enables precise control over the thickness of TiO₂ nanotubes. Anodization can also be used to create decorative and colored coatings on titanium nanotubes. In this study, a combined structure including anodic TiO₂ nanotubes and SrTiO₃ particles was fabricated using chemical synthesis techniques. TiO₂ nanotubes were prepared by anodizing them in ethylene glycol containing NH₄F and H₂O while applying a voltage of 30 volts. An anode nanotube array heat-treated at 450 °C was then placed in an autoclave filled with dilute SrTiO₃ solution. Scanning electron microscopy (SEM) analysis showed that the TNTs were characterized by clear and open tube ends, with an average outer diameter of 1.01 μm and an inner diameter of 69 nm, and their length is 133 nm. The results confirm the successful formation of a structure that can be potentially applied in a variety of applications, including hydrogen production by the photocatalytic decomposition of water under sunlight. Full article

This paper presents the results of measurements of ignition delay times in hydrogen–oxygen mixtures highly diluted with argon. The experiments were carried out behind an incident shock wave at temperatures from 870 to 2500 K, pressures from 0.5 to 1.5 atm, and equivalence ratios from 0.1 to 2.0. The results obtained were processed in terms of the partial pressure of the combustible mixture stoichiometric part that is consumed in the combustion process. An almost linear dependence of the ignition delay time on the reciprocal value of the partial pressure was found for both rich and lean mixtures. The measured data are compared with calculations based on the previously developed kinetic model and experimental data from other authors. Full article

Teaching and research laboratories generate wastes of various compositions and volumes, ranging from diluted aqueous solutions to concentrated ones, which, due to milder self-regulation waste-management policies, are carelessly discarded, with little attention given to the consequences for the environment and human health. In this sense, the current study proposes the application of the supercritical water oxidation (SCWO) process for the treatment of complex refractory wastewater generated in research and teaching laboratories of universities. The SCWO, which uses water in conditions above its critical point (T > 647.1 K, p > 22.1 MPa), is regarded as an environmentally neutral process, uniquely adequate for the degradation of highly toxic and bio-refractory organic compounds. Initially, the wastewater samples were characterized via headspace gas chromatography coupled with mass spectrometry. Then, using a continuous tubular reactor, the selected operational parameters were optimized by a Taguchi L9 experimental design, aiming to maximize the total organic carbon reduction. Under optimized conditions—that is, temperature of 823.15 K, feed flow rate of 10 mL min⁻¹, oxidizing ratio of 1.5 (50% excess over the oxygen stoichiometric ratio), and sample concentration of 30%—TOC, COD, and BOD reductions of 99.9%. 91.5% and 99.2% were achieved, respectively. During the treatment process, only CO₂, methane, and hydrogen were identified in the gaseous phase. Furthermore, the developed methodology was applied for the treatment of wastewater samples generated in another research laboratory and a TOC reduction of 99.5% was achieved, reinforcing the process’s robustness. A thermodynamic analysis of SCWO treatment of laboratory wastewater under isothermal conditions was performed, using the Gibbs energy minimization methodology with the aid of the GAMS^® 23.9.5. (General Algebraic Modeling System) software and the CONOPT 4 solver. Therefore, the results showed that SCWO could be efficiently applied for the treatment of wastewater generated by different teaching and research laboratories without the production of harmful gases and the addition of hazardous chemicals. Full article

Hydrolysis of light metals and hydrides can potentially be used for the generation of hydrogen on-board fuel cell vehicles, or, alternatively, for refilling their fuel tanks with H₂ generated and pressurised without compressor on site, at near-ambient conditions. Implementation of this approach requires solution of several problems, including the possibility of controlling H₂ release and avoiding thermal runaway. We have solved this problem by developing the apparatus for the controlled generation of pressurised H₂ using hydrolysis of Mg or MgH₂ in organic acid solutions. The development is based on the results of experimental studies of MgH₂ hydrolysis in dilute aqueous solutions of acetic, citric, and oxalic acids. It was shown that the hydrogen yield approaches 100% with a fast hydrolysis rate when the molar ratio acid/MgH₂ exceeds 0.9, 2.0, and 2.7 for the citric, oxalic, and acetic acids, respectively. In doing so, the pH of the reaction solutions after hydrolysis corresponds to 4.53, 2.11, and 4.28, accordingly, testifying to the buffer nature of the solutions “citric acid/magnesium citrate” and “acetic acid/magnesium acetate”. We also overview testing results of the developed apparatus where the process rate is effectively controlled by the control of the acid concentration in the hydrolysis reactor. Full article

The green transition initiative has exposed the importance of effective recycling of Nd-Fe-B magnets for achieving sustainability and foreign independence. In this study, we considered strip-cast, hydrogenated, jet-milled Nd-Fe-B powder as a case study to explore the potential for selective chemical leaching of the Nd-rich phase, aiming to extract the Nd₂Fe₁₄B matrix phase. Diluted citric and nitric acids at concentrations of 0.01, 0.1, and 1 M were considered potential leaching mediums, and the leaching time was 15 min. Microstructural investigation, magnetic characterization, and elemental compositional analysis were performed to investigate leaching efficiency and selectivity. Based on SEM analysis, Nd/Fe ratio monitoring via ICP-MS, and the high moment/mass value at 160 emu/g for the sample leached with 1 M citric acid, 1 M citric acid proved highly selective toward the Nd-rich phase. Exposure to nitric acid resulted in a structurally damaged Nd₂Fe₁₄B matrix phase and severely diminished moment/mass value at 96.2 emu/g, thus making the nitric acid unsuitable for selective leaching. The presence of hydrogen introduced into the material via the hydrogen decrepitation process did not notably influence the leaching dynamics. The proposed leaching process based on mild organic acids is environmentally friendly and can be scaled up and adopted for reprocessing industrial scrap or end-of-life Nd-Fe-B magnets to obtain single-phase Nd-Fe-B powders that can be used for novel magnet-making. Full article

Deep eutectic solvents (DESs) have upgraded the practices of valorizing lignocellulosic feedstock by lessening biomass recalcitrance through delignification in precise and economical manner. In this study, the influence of a series of deep eutectic mixtures was evaluated on the halophyte Atriplex crassifolia for achieving elevated biogas production. Initially, the biomass was pretreated via several DESs with varying hydrogen bond donors (HBDs) including carboxylic acids, amine/amide, and polyols/glycols. DES composed of choline chloride (ChCl) and lactic acid (LA) evidenced as the most effective solvent in achieving high lignin removal rates and was further optimized by evaluating the parameters of molar ratio of DES components, solid-to-liquid ratio, and solvent addition. A maximum delignification value of 89.5% was achieved by 15% diluted ChCl: LA (1:2) DES at a biomass loading of 1:15. The solubilization rate of diluted ChCl: LA was also raised up to 38%. FT-IR analysis revealed significant lignin elimination from ChCl: LA pretreated substrates. Moreover, ≥88% of ChCl: LA DES was recovered after up to three pretreatment cycles, retaining ≥85% delignification efficiency. Fresh DES-pretreated Atriplex crassifolia recorded 32.2 mL/g of biogas production yield due to increased cellulosic content. The findings validated Atriplex crassifolia as an efficient feedstock for biogas production and confirmed the affectivity of ChCl: LA pretreatment in eliminating the lignin barrier, ultimately making cellulosic sugars readily biodegradable and highly accessible for anaerobic microorganisms. Full article

Hydrogen is the energy vector that will lead us toward a more sustainable future. It could be the fuel of both fuel cells and internal combustion engines. Internal combustion engines are today the only motors characterized by high reliability, duration and specific power, and low cost per power unit. The most immediate solution for the near future could be the application of hydrogen as a fuel in modern internal combustion engines. This solution has advantages and disadvantages: specific physical, chemical and operational properties of hydrogen require attention. Hydrogen is the only fuel that could potentially produce no carbon, carbon monoxide and carbon dioxide emissions. It also allows high engine efficiency and low nitrogen oxide emissions. Hydrogen has wide flammability limits and a high flame propagation rate, which provide a stable combustion process for lean and very lean mixtures. Near the stoichiometric air–fuel ratio, hydrogen-fueled engines exhibit abnormal combustions (backfire, pre-ignition, detonation), the suppression of which has proven to be quite challenging. Pre-ignition due to hot spots in or around the spark plug can be avoided by adopting a cooled or unconventional ignition system (such as corona discharge): the latter also ensures the ignition of highly diluted hydrogen–air mixtures. It is worth noting that to correctly reproduce the hydrogen ignition and combustion processes in an ICE with the risks related to abnormal combustion, 3D CFD simulations can be of great help. It is necessary to model the injection process correctly, and then the formation of the mixture, and therefore, the combustion process. It is very complex to model hydrogen gas injection due to the high velocity of the gas in such jets. Experimental tests on hydrogen gas injection are many but never conclusive. It is necessary to have a deep knowledge of the gas injection phenomenon to correctly design the right injector for a specific engine. Furthermore, correlations are needed in the CFD code to predict the laminar flame velocity of hydrogen–air mixtures and the autoignition time. In the literature, experimental data are scarce on air–hydrogen mixtures, particularly for engine-type conditions, because they are complicated by flame instability at pressures similar to those of an engine. The flame velocity exhibits a non-monotonous behavior with respect to the equivalence ratio, increases with a higher unburnt gas temperature and decreases at high pressures. This makes it difficult to develop the correlation required for robust and predictive CFD models. In this work, the authors briefly describe the research path and the main challenges listed above. Full article

Drought stress severely threatens plant growth, yield and survivability. Wood vinegar, formed by the condensation of smoke produced during biochar production, has been shown to promote plant growth and enhance stress tolerance. They have now been recognized as a sustainable alternative and are frequently used exogenously to support plants coping with environmental stress. This study aimed to evaluate the efficacy of oil palm wood vinegar (OPWV) in mitigating the adverse effects of drought stress on Pandanus amaryllifolius. The optimal concentrations and frequencies of OPWV application were determined before the drought treatment. The results showed that the imposed drought stress negatively affected the plant growth parameters but applying OPWV at 1:500 dilution at 3-day intervals for 12 days increased its tolerance. These include increased leaf relative water content, root-to-shoot ratio, relative stem circumference, chlorophyll pigments and antioxidant enzyme activities. In contrast, the drought-stressed plants treated with OPWV showed decreased relative electrolyte leakage, hydrogen peroxide, proline, malondialdehyde, and enhanced drought-responsive gene expressions, such as HSP70, GAPDH, and Thau, while ENO and β-Fruc were reduced. These biostimulatory effects of OPWV might be due to several antioxidant compounds, such as anthranilic acid, tetrasiloxane, syringol, guaiacol, and catechol. Altogether, our results showed the effectiveness of OPWV in alleviating the adverse effects of drought stress, and as such, OPWV could be potentially applied in agriculture. Full article

In this study, chitooligosaccharide-niacin acid conjugate was designed and synthesized through the reaction of chitooligosaccharide and nicotinic acid with the aid of N,N′-carbonyldiimidazole. Its cationic derivatives were prepared by the further nucleophilic substitution reaction between the chitooligosaccharide-niacin acid conjugate and bromopropyl trialkyl ammonium bromide with different alkyl chain lengths. The specific structural characterization of all derivatives was identified using Fourier Transform Infrared Spectroscopy (FTIR) and Nuclear Magnetic Resonance (NMR), and the degree of substitution was obtained using the integral area ratio of the hydrogen signals. Specifically, the antibacterial activities against Escherichia coli, Staphylococcus aureus, Pseudoalteromonas citrea and Vibrio harveyi were evaluated using broth dilution methods. In addition, their antifungal activities, including Botrytis cinerea, Glomerella cingulate and Fusarium oxysporum f. sp. cubense were assayed in vitro using the mycelium growth rate method. Experimental data proved that the samples showed antibacterial activity against four pathogenic bacteria (MIC = 1–0.125 mg/mL, MBC = 8–0.5 mg/mL) and enhanced antifungal activity (50.30–68.48% at 1.0 mg/mL) against Botrytis cinerea. In particular, of all chitooligosaccharide derivatives, the chitooligosaccharide derivative containing pyridinium and tri-n-butylamine showed the strongest antibacterial capacity against all of the test pathogenic bacteria; the MIC against Vibrio harveyi was 0.125 mg/mL and the MBC was 1 mg/mL. The experimental results above showed that the introduction of pyridinium salt and quaternary ammonium salt bearing trialkyl enhanced the antimicrobial activity. In addition, the cytotoxicity against L929 cells of the chitooligosaccharide derivatives was evaluated, and the compounds exhibited slight cytotoxicity. Specifically, the cell viability was greater than 91.80% at all test concentrations. The results suggested that the cationic chitooligosaccharide derivatives bearing pyridinium and trialkyl ammonium possessed better antimicrobial activity than pure chitooligosaccharide, indicating their potential as antimicrobial agents in food, medicine, cosmetics and other fields. Full article