Search Results (13)

Multipolar bonded magnets based on a thermoset matrix provide the opportunity to expand the applications of bonded magnets, especially within the drive technology industry, in terms of the high thermal and chemical resistance, along with a higher utilisation of the magnetic potential. To realize the application of polymer bonded magnets based on thermosets within the drive technology industry, general design parameters in terms of the material, the process parameters, and the tool concept are needed. These allow for a fundamental realization of multipolar bonded magnets with complex geometries in drive technologies, based on thermosets as the matrix material. This paper investigates the impact of the material (matrix material and filler grade), the process conditions (holding pressure (p_h) and heating time (t_h)), and the tool concept (gating position and system, sleeve material, pole division, and sample thickness) on the magnetic properties in terms of the remanence (B_R) and the deviation (Δs) of the pole division, as well as the orientation of the fillers in the middle of the pole and at the pole pitch. For each parameter, an optimised value is derived. In the majority of the cases, this value is equal in terms of the magnetic properties and the orientation. In terms of the sleeve material and the sample thickness, the ideal value differs between the two criteria. Therefore, an optimised value for each criterion, as well as an overall value, is defined. In terms of the material, PF, along with a high filler grade; in terms of the process conditions, a high holding pressure (p_h) and a low heating time (t_h); and in terms of the tool concept, a two-pinpoint gating system, located in the middle of the pole, a Ferro-Titanit-Cromoni sleeve material, a high pole division, as well as small sample thickness, should be selected to improve the properties of polymer bonded magnets based on thermosets. Full article

Elastomers are made of chain-like molecules to form networks that can sustain large deformation. Rubbers are thermosetting elastomers that are obtained from irreversible curing reactions. Curing reactions create permanent bonds between the molecular chains. On the other hand, thermoplastic elastomers do not need curing reactions. Incorporation of appropriated filler particles, as has been practiced for decades, can significantly enhance mechanical properties of elastomers. However, there are fundamental questions about polymer matrix composites (PMCs) that still elude complete understanding. This is because the macroscopic properties of PMCs depend not only on the overall volume fraction ($\varphi$) of the filler particles, but also on their spatial distribution (i.e., primary, secondary, and tertiary structure). This work aims at reviewing how the mechanical properties of PMCs are related to the microstructure of filler particles and to the interaction between filler particles and polymer matrices. Overall, soft rubbery matrices dictate the elasticity/hyperelasticity of the PMCs while the reinforcement involves polymer–particle interactions that can significantly influence the mechanical properties of the polymer matrix interface. For $\varphi$ values higher than a threshold, percolation of the filler particles can lead to significant reinforcement. While viscoelastic behavior may be attributed to the soft rubbery component, inelastic behaviors like the Mullins and Payne effects are highly correlated to the microstructures of the polymer matrix and the filler particles, as well as that of the polymer–particle interface. Additionally, the incorporation of specific filler particles within intelligently designed polymer systems has been shown to yield a variety of functional and responsive materials, commonly termed smart materials. We review three types of smart PMCs, i.e., magnetoelastic (M-), shape-memory (SM-), and self-healing (SH-) PMCs, and discuss the constitutive models for these smart materials. Full article

With the rapid development of highly integrated electronic devices and high-frequency microwave communication technology, the parasitic resistance–capacitance (RC) delay and propagation loss severely restrict the development of a high-frequency communication system. Benefiting from its low dielectric constants (D_k) and low dielectric loss factor (D_f), polyphenylene oxide (PPO) has attracted widespread attention for its application in the dielectric layers of integrated circuits. However, PPO suffers from a very high melting viscosity, a larger coefficient of thermal expansion than copper wire and poor solvent resistance. Recently, many efforts have focused on the modification of PPO by various means for communication applications. However, review articles focusing on PPO are unexpectedly limited. In this article, the research progress concerning PPO materials in view of the modification of PPO has been summarized. The following aspects are covered: polymerization and design of special chemical structure, low molecular weight PPO and blending with thermosetting resin, hyperbranched PPO, thermosetting PPO and incorporating with fillers. In addition, the advantages and disadvantages of various types of modification methods and their applications are compared, and the possible future development directions are also proposed. It is believed that this review will arouse the interest of the electronics industry because of the detailed summary of the cutting-edge modification technology for PPO. Full article

Vitrimers, as dynamic covalent network polymers, represent a groundbreaking advancement in materials science. They excel in their applications, such as advanced thermal-conductivity composite materials, providing a sustainable alternative to traditional polymers. The incorporation of vitrimers into composite fillers enhances alignment and heat passway broadly, resulting in superior thermal conductivity compared to conventional thermosetting polymers. Their dynamic exchange reactions enable straightforward reprocessing, fostering the easy reuse of damaged composite materials and opening possibilities for recycling both matrix and filler components. We review an overview of the present advancements in utilizing vitrimers for highly thermally conductive composite materials. Full article

Multipolar bonded magnets based on thermosets offer the opportunity to expand the applications of bonded magnets with respect to an increasing chemical and thermal resistance compared to thermoplastics. To utilise this option, the correlation between the material system and the magnetic properties must be explored amongst other influencing factors. This paper investigates the magnetic properties and the orientation of thermoset- (epoxy resin and phenolic resin) based bonded ring magnets with a hard magnetic filler of strontium-ferrite-oxide. The influence of the matrix material and the filler grade on the magnetic properties is correlated with the material characterisation showing a high impact of the embedding of the fillers into the matrix on the orientation and with that the magnetic properties. Based on a network theory, it can be justified that the magnetic properties can be increased due to a phenolic resin and a high filler grade. Further, it was shown that the orientation along the sample depth is highly affected by the strength of the outer magnetic field and limited in terms of the high-tool temperature in a thermoset-based production. With that, the sample depth, which reveals a proper orientation, is restricted so far. Full article

To expand the range of applications of multipolar bonded magnets based on a thermoplastic matrix, the chemical and thermal resistance has to be increased and the reduced orientation in the rapid solidified surface layer has to be overcome. To meet these requirements, the matrix of multipolar bonded magnets can be based on thermosets. This paper investigates in the magnetic properties, especially in the orientation of hard magnetic fillers, the pole accuracy and the mechanical properties of multipolar bonded ring magnets based on the hard magnetic filler strontium-ferrite-oxide and compares the possibilities of thermoplastic (polyamide)- and thermoset (epoxy resin, phenolic resin)-based matrices. It was shown that the magnetic potential of the thermoset-based material can only be fully used with further magnetization. However, the magnetic properties can be increased using thermoset-based compounds compared to thermoplastics in multipolar bonded ring magnets. Further, a model of the orientation and pole accuracy is found in terms of thermoset-based multipolar magnets. In addition, the change of the mechanical properties due to the different matrix systems was shown, with an increase in E-Modulus, E_t, and a reduction in tensile strength, σ_m, and elongation at break, ε_m, in terms of thermosets compared to thermoplastics. Full article

A completely opposite injection molding filling behavior of thermosets and thermoplastics by an effective and useful method developed by the authors was found. Specifically, for the thermoset injection molding, there is a strong slip between the thermoset melt and wall surface, which is not found for the injection molding of thermoplastic materials. In addition, the variables, such as the filler content, the mold temperature, the injection speed, and the surface roughness that could lead to or influence the slip phenomenon of thermoset injection molding compounds, were also investigated. Furthermore, microscopy was conducted to verify the correlation between the mold wall slip and fiber orientation. The results obtained in this paper open challenges in the field of the calculation, analysis, and simulation of mold filling behavior of highly glass fiber-reinforced thermoset resins in the injection molding process with consideration of wall slip boundary conditions. Full article

Polymer-bonded magnets have increased significantly in the application of drive technology, especially in terms of new concepts for the magnetic excitation of synchronous or direct current (DC) machines. To satisfy the increasing demand of hard magnetic filler particles and especially rare earth materials in polymer-bonded magnets, different strategies are possible. In addition to the reduction in products or the substitution of filler materials, the recycling of polymer-bonded magnets is possible. Different strategies have to be distinguished in terms of the target functions such as the recovery of the matrix material, the filler or both materials. In terms of polymer-bonded magnets, the filler material—especially regarding rare earth materials—is important for the recycling strategy due to the limited resource and high costs. This paper illustrates two different recycling strategies relative to the matrix system of polymer-bonded magnets. For thermoset-based magnets, a thermal strategy is portrayed which leads to similar magnetic properties in terms of the appropriated atmosphere and process management. The mechanical reusage of shreds is analyzed for thermoplastic-based magnets. The magnetic properties are reduced by about 20% and there is a change in the flow conditions and with that, an influence on the pole accuracy. Full article

The applications of bonded magnets in the field of injection-molded samples can be expanded by thermoset-based polymer-bonded magnets, as thermosets provide the opportunity to comply with the demands of, for example, the chemical industry or pump systems in drive applications through to their improved chemical and thermal resistance, viscosity and creep behaviour, especially compared to thermoplastic-based magnets. This paper investigates the influence of the matrix material (epoxy resin, phenolic resin), the filler type (strontium-ferrite-oxide, neodymium-iron-boron) and the filler grade on the reaction kinetics and the viscosity. Based on the determination of the impact, the theory of the network structure is founded. The network and the cross-linked structure are essential to know, as they significantly define not only the material but also the sample behaviour. The correlation between the material system and the mechanical as well as the magnetic properties is portrayed based on the general understanding of the behaviour in terms of the reaction kinetics and the viscosity as well as the theory of the network structure. With that, a basic understanding of the correlation within the material system (matrix, filler, filler grade) and between the reaction kinetics, the network and the cross-linked structure was determined, which gives the opportunity to change the mechanical and the magnetic properties based on the analyzed impact factors and to expand the applications of bonded magnets in the field of thermoset-based ones. Full article

The three-dimensional (3D) printing of a SiO₂-filled thermosetting polyimide (SiO₂@TSPI) composite with outstanding performance is realized via the direct ink writing (DIW) of polyamide acid (PAA) composite ink and thermal treatment conducted thereafter. The composite ink consists of phenylethynyl-terminated PAA and silica nanoparticles, where the SiO₂ nanoparticles serve as the rheology modifier that is necessary for the DIW technique to obtain self-supporting feedstock during 3D printing and the reinforcement filler that is used to enhance the performance of the final composite. As a result, printed parts with complex geometry and robust thermal stability are obtained. Due to the extrusion-based DIW technique, the printed structures exhibit anisotropic mechanical strength that highly depends on printing roads. This simple and convenient means of realizing 3D structures of thermosetting polyimides is a promising strategy in aerospace and other fields. Full article

Polymer bonded magnets based on thermoplastics are economically produced by the injection molding process for applications in sensor and drive technology. Especially the lack of orientation in the edge layer, as well as the chemical resistance and the creep behavior limit the possible implementations of thermoplastic based polymer bonded magnets. However, thermoset based polymer bonded magnets have the opportunity to expand the applications by complying with the demands of the chemical industry or pump systems through to improved chemical and thermal resistance, viscosity and creep behavior of thermosets. This paper investigates the influence of hard magnetic particles on the flow and curing behavior of highly filled thermoset compounds based on an epoxy resin. The basic understanding of the behavior of those highly filled hard magnetic thermoset systems is essential for the fabrication of polymer bonded magnets based on thermosets in the injection molding process. It is shown that several factors like the crystal structure, the particle shape and size, as well as the thermal conductivity and the adherence between filler and matrix influence the flow and curing behavior of highly filled thermoset compounds based on epoxy resin. However, these influencing factors can be applied to any filler system with respect to a high filler amount in a thermoset compound, as they are based on the material behavior of particles. Further, the impact of the flow and curing behavior on the magnetic properties of polymer bonded magnets based on thermosets is shown. With that, the correlation between material based factors and magnetic properties within thermosets are portrayed. Full article

Recycling and recovery of waste tires is a serious environmental problem since vulcanized rubbers require several years to degrade naturally and remain for long periods of time in the environment. This is associated to a complex three dimensional (3D) crosslinked structure and the presence of a high number of different additives inside a tire formulation. Most end-of-life tires are discarded as waste in landfills taking space or incinerated for energy recovery, especially for highly degraded rubber wastes. All these options are no longer acceptable for the environment and circular economy. However, a great deal of progress has been made on the sustainability of waste tires via recycling as this material has high potential being a source of valuable raw materials. Extensive researches were performed on using these end-of-life tires as fillers in civil engineering applications (concrete and asphalt), as well as blending with polymeric matrices (thermoplastics, thermosets or virgin rubber). Several grinding technologies, such as ambient, wet or cryogenic processes, are widely used for downsizing waste tires and converting them into ground tire rubber (GTR) with a larger specific surface area. Here, a focus is made on the use of GTR as a partial replacement in virgin rubber compounds. The paper also presents a review of the possible physical and chemical surface treatments to improve the GTR adhesion and interaction with different matrices, including rubber regeneration processes such as thermomechanical, microwave, ultrasonic and thermochemical producing regenerated tire rubber (RTR). This review also includes a detailed discussion on the effect of GTR/RTR particle size, concentration and crosslinking level on the curing, rheological, mechanical, aging, thermal, dynamic mechanical and swelling properties of rubber compounds. Finally, a conclusion on the current situation is provided with openings for future works. Full article

The aim of the article is to present recent developments in material research with bisphenyl-polymer/carbon-fiber-reinforced composite that have produced highly influential results toward improving upon current titanium bone implant clinical osseointegration success. Titanium is now the standard intra-oral tooth root/bone implant material with biocompatible interface relationships that confer potential osseointegration. Titanium produces a TiO₂ oxide surface layer reactively that can provide chemical bonding through various electron interactions as a possible explanation for biocompatibility. Nevertheless, titanium alloy implants produce corrosion particles and fail by mechanisms generally related to surface interaction on bone to promote an inflammation with fibrous aseptic loosening or infection that can require implant removal. Further, lowered oxygen concentrations from poor vasculature at a foreign metal surface interface promote a build-up of host-cell-related electrons as free radicals and proton acid that can encourage infection and inflammation to greatly influence implant failure. To provide improved osseointegration many different coating processes and alternate polymer matrix composite (PMC) solutions have been considered that supply new designing potential to possibly overcome problems with titanium bone implants. Now for important consideration, PMCs have decisive biofunctional fabrication possibilities while maintaining mechanical properties from addition of high-strengthening varied fiber-reinforcement and complex fillers/additives to include hydroxyapatite or antimicrobial incorporation through thermoset polymers that cure at low temperatures. Topics/issues reviewed in this manuscript include titanium corrosion, implant infection, coatings and the new epoxy/carbon-fiber implant results discussing osseointegration with biocompatibility related to nonpolar molecular attractions with secondary bonding, carbon fiber in vivo properties, electrical semiconductors, stress transfer, additives with low thermal PMC processing and new coating possibilities. Full article